Search Documents

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962

By Paul R. Smith

The theoretical requirements for the flotation d large particles are discussed. A flotation machine is described which has components which meet many of the theoretical requirements for the flotation of large particles. The machine&apos;s salient features include multiple fine-bubble attachment, froth level feeding, quiescence, shallow depth, and short flotation time. Test conditions and results are presented for the laboratory flotation of 10 mesh phosphate, 4 mesh potash, and 1/2 inch coal. In addition, test conditions and results of pilot plant flotation of minus 14 plus 35 mesh phosphate and minus 14 plus 150 mesh phosphate are also presented.

Jan 1, 1969

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

By A. T. Yu

Two key components make up the core of a rapid excavation operation. They are: the breaking up of the rock and its removal. Owing to the complexity inherent in mechanical rock-breaking and the relative infancy of the art, for a number of years the first of these two components has received virtually undivided attention from the industry. Only recently has some concern been expressed about the technology and the economics of the much ignored second component: muck removal. As the continuous boring machine&apos;s percentage downtime continues to trend lower in the future, the need for adequate and more effective materials handling systems in rapid excavation will become increasingly more acute. (1) Recognition of the need for a broader and more far-sighted approach to our problem has been eloquently underscored in the conclusions of the Committee on Rapid Excavation sponsored by the National Research Council: "Ultimate attainment of the desired cost and speed improvements is significantly dependent on recognition of the excavation process as a system whose subsystems are critically inter-related. Substantial amounts of full-scale field testing of integrated driving, muck removal, and support subsystems are required." (2)

Jan 1, 1997

By Samuel P. Polack

This report reviews investigations to determine the fire hazard in coal mining when using flammable petroleum hydraulic oils to actuate mining equipment and summarizes research by the Bureau of Mines and industry on fire-resistant hydraulic fluids. Tests were established to evaluate fire resistance and the necessary characteristics to assure adequate service when fire-resistant fluids are used to replace petroleum hydraulic oils. The research was conducted in the laboratory and field trials under actual operating conditions in underground mines. Bureau of Mines Schedule 30 became effective December 17, 1959; the first approval was granted on February 18, 1960, and the twelfth was granted on March 17, 1961. The approvals include nine ready-mixed (by the producer) fluids and seven concentrates to which water is added by the user according to instructions from the producer. Seven synthetic-type fire-resistant hydraulic fluids submitted by two producers are also approved. Over 100 coal mines are now using water-in-oil emulsion-type fire-resistant hydraulic fluids in varying degrees from a trial in one machine to all the hydraulic equipment in an entire mine.

Jan 1, 1961

Metso Minerals Process Technology Asia-Pacific (MMPT-AP) has been working with many mining companies worldwide performing `Mine to Mill&apos; or Process Integration and Optimisation (PIO) studies. MMPT-AP has developed a proven methodology to improve the efficiency of the mine-mill interface and gain maximum benefit. The PIO methodology involves rock characterisation, mathematical modelling and simulation to generate a list of operational and control changes for both the mine and concentrator. Following the methodology, the list of recommendations is developed relatively easily; the more challenging part depends on the company. Success of a PIO project relies on the ability of an organisation to implement change - both operationally and culturally: the human element. When a PIO project is started, there is initial interest and commitment from the company. But how can this be maintained? How does an operation know if the benefit continues? MMPT AP is now developing long-term relationships with clients to ensure that the increased production and improved efficiency continues. Direct and indirect measurements are used to determine the key factors involved and to understand the cause/effect relationships. Simulation tools also can be used to compare current with recommended practices - so when material properties vary over time, the benefits can still be quantified. PIO is about empowerment: by measuring and understanding what parameters affect concentrator performance, the site personnel now have the knowledge to make a difference. Rather than simply reporting variable or poor concentrator performance, operations can predict when production will be affected and put controls in place to prevent it from happening. This requires support and commitment from the company or `buy in&apos;. Ensuring this buy in continues is the challenge facing every company involved in PIO work - but the benefits are well worth it. This paper will review MMPT-AP&apos;s experiences in implementing PIO projects in the long term: from both the consulting and operational viewpoints. MMPT-AP&apos;s involvement with a number of companies will be discussed as examples of what works and what does not.

Jan 1, 2007

By M. Karsten

Platinum mines in the Bushveld Complex are located in areas with a high geothermal gradient. This means that, compared to, for example, gold mines of the Witwatersrand region, high rock temperatures are encountered at relatively shallower depths. Thus air cooling and refrigeration need to be considered at early stages in mine development. Another factor that influences air cooling and ventilation requirements is the use of trackless diesel equipment for loading and hauling broken rock. At shallower depths it will be more cost-effective to locate the cooling and ventilation equipment on surface, whereas for deeper mines the more cost-effective option is to locate cooling equipment underground. For intermediate depths, trade-off studies need to be undertaken to determine the optimum mix between more cooling and less air or more air and less cooling, as well as the optimum location for this cooling equipment. Factors that are taken into account include power requirements, positional efficiency, and additional infrastructure requirements. Traditionally the approach has been to ventilate ?all of the mine all of the time?. However, with increasing power costs and growing pressure to ensure sustainability, this strategy must be modified to apply ventilation and cooling on demand. In other words, both cooling and ventilation equipment should be operated only when needed and should be adjusted to the demand at the time. Obviously there will be areas that will need to be ventilated (and cooled) continuously (for example, for dilution of flammable gases), but this can be built in to the overall strategy. In addition, in devising ventilation on demand (VoD) strategies, occupational criteria relating to exposure to gases, noise, and heat need to be taken into account. This paper discusses options available for implementing energy-efficient ventilation and cooling systems and suggests ways of changing traditional thinking in the overall ventilation and cooling of mines. Efficient ventilation and cooling designs can play a major role in improving sustainability and reducing energy costs and carbon footprint.

Jan 1, 2012

By Leland E. Paulson

This investigation examined the feasibility of altering the inorganic component of North Dakota lignite by ion exchange. Lignite of specific size consist was washed with various ionic solutions and examined for evidence of exchange. Ions of higher valance substituted preferentially at equivalent concentrations. Results indicate that a major portion of the inorganic material associated with lignite is combined in exchangeable form with the organic component. Particle size of the treated coal is a critical factor in determining the rate of exchange. The data indicate that monovalent ions are easily replaced by divalent and trivalent ions, and the presence of ionic material in slurries containing finely divided lignite significantly increases filtration rates.

Jan 1, 1968

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 1/8-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Vladimir Adamek

Two existing predictive methods were chosen for evaluation; an influence function (Gals Theory) and a profile function (hyperbolic). These were applied to several field measured subsidence pro¬files over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1981

By Stéphane Robert

This document presents estimates of future "total cash cost per ounce" and "minesite cost per tonne" that are not recognized measures under United States generally accepted accounting principles ("US GAAP"). This data may not be comparable to data presented by other gold producers. These future estimates are based upon the total cash costs per ounce and minesite costs per tonne that the Company expects to incur to mine gold at the applicable projects and do not include production costs attributable to accretion expense and other asset retirement costs, which will vary over time as each project is developed and mined. It is therefore not practicable to reconcile these forward-looking non-GAAP financial measures to the most comparable GAAP measure. A reconciliation of the Company&apos;s total cash cost per ounce and minesite cost per tonne to the most comparable financial measures calculated and presented in accordance with US GAAP for the Company&apos;s historical results of operations is set forth in the notes to the financial statements included in the Company&apos;s Annual Information Form and Annual Report on Form 20-F, for the year ended December 31, 2009, as well as the Company&apos;s other filings with the Canadian Securities Administrators and the SEC.

May 1, 2011

By Sun-Hee Cheong

This study sought to produce L(+)-calcium lactate using precipitated calcium carbonate as a starter culture composite of lactic acid bacteria in lactic acid fermentation. Specifically, precipitated calcium carbonate was synthesized by reacting calcium hydroxide with sodium carbonate in the previous study by the authors. Synthetic precipitated calcium carbonate was then used as the calcium source of lactic acid bacteria during the fermentation process. In general, precipitated calcium carbonate has low absorption rate in the human body. On the other hand, calcium lactate has high absorption rate; it is commonly used in food and drug industries as calcium additives in various foods such as cookies, beverages, bread, sauces, powdered milk, and fruit juice. Calcium lactate has two racemates, e.g., L(+)-lactate and D(-)-lactate. In particular, L(+)-lactate is known to be more soluble than D(-)-lactate and generally produced from lactose by homo-fermentative lactic acid bacteria such as Lactococcus spp., Lactobacillus plantarum, Lactobacillus casei, Lactobacillus curvatus, and Pediococcus spp. Thus, the characteristics of the pertinent lactic acid bacteria and optimal condition such as temperature, pH, precipitated calcium carbonate addition rate, and content of fermentation for increasing formation yield and purity were investigated. The findings suggested the possibility of manufacturing L(+)-calcium lactate using precipitated calcium carbonate as a calcium source with high value-added instead of commercial calcium lactate.

Jan 1, 2006

By Fieldner. A. C.

"In preparing this paper, an attempt was made to obtain results of plant-scale carbonization tests on washed and unwashed coal tram to same mine. A letter. in which the following questions were asked, was sent to some 50 coke-oven superintendents and others who might be interested:“What is the influence of washing coal on:(1) The chemical and physical properties of coke, as for example, the size, the amount of breeze, the fracture, strength, cell-structure, etc.(2) The quantity and quality of gas and by-products.(3) The capacity of the ovens.(4) The composition of the coal..""Your general opinion, as well as any specific data or results of testa, on this important subject will be greatly appreciated.""Of the 45 replies received, 24 stated that they had never used washed coal; 11 had used washed coal but had no comparative data on similar coals washed and unwashed; 7 answered some of the questions based on their general experience; and 3 gave some test data on Pittsburgh bed coal from western Pennsylvania. In none of the three tests did the washed coal come from the same mine as the unwashed. The washed coals in the three tests were from the same washery - one of modern construction in which the operations are under careful technical control in order to give a uniform product containing a minimum of surface moisture. The unwashed coals which were previously used in these plants were from different nearby mines in the same coal bed, and were supplied by the same company. Obviously, no sweeping or finale conclusions can be drawn from these few tests on coal from a single washery. Therefore, the writer vas obliged to consult the literature, coal-carbonization and coal-washing engineers, and other authorities to supplement the fragmentary information gleaned from the questionnaires in order to present a picture of chat gas engineers may expect from the use of washed coal in a carbonizing plant."

May 1, 1930

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By K. W. Fritzsche

The prosperity of any nation depends, to a large extent, on its natural resources such as oil, coal, &apos;metal, timber, waterpower, and fertile soil. Each one of these resources forms the basis of a huge industry. The mining and smelting industry ranks among the first since it paves the way for a number of other industries. The mines and smelters provide a market for electric power, coal, timber, and agricultural products: other industries in turn provide a market for metals and non-metals. The real pioneering, however, is done by the prospector who goes into the wilderness to search for the ores from which the metals are to be extracted for the use of men. Prospecting is an interesting and fascinating occupation. There are many difficulties and hardships in the way but the lure of gold and the vision of finding an outcrop that may develop into a large bank account, within a reasonably short time, will urge the prospector forward. Thus, on the outskirts of this northern hemisphere hundreds of prospectors are searching and toiling and of whom nothing is known or heard until they reach civilization and announce a new discovery. Then a mad rush takes place and everybody who can afford to go will take a gamblers chance and plant stakes in the neighbourhood of the new discovery, or wherever an outcrop of mineralized rock can be found, with the hope of winning a fortune.

Jan 1, 1925

By S. K. Mahata, P. G. Suresh Kumar, B. B. Singh

Improvement of post tap hole practices is achievable by mechanized handling of melt during the production of Ferro Chrome, resulting in higher recovery of chromium. The paper deals with modern practices adopted in the production of ferro-chrome since past two decades. The methods and practices deal with various areas : a) Improved method of operating the tap hole by selection of right quality of refractory to maintain the life of tap hole. b) Collection of melt in different types of receptacles like refractory brick lined mild steel ladles, cast steel ladles, cast iron pans being chosen for cost effective and efficient handling. c) Separation of slag and metal, casting of metal, crushing, sizing and stock piling etc. d) Slag disposal and recovery of entrapped metal. The drive behind the above development is continuous improvement, which results in higher chromium recovery and reduces loss of metal in slag by completely mechanized method so as to be at the same level with producers of ferro-chrome in other advanced countries , in the emerging global economy.

Jan 1, 2007

By Alfonso Nájera

Turbulent flow of liquid steel and its control is studied using different geometries of turbulence inhibitors. Four designs of turbulence inhibitors were characterized through experiments of tracer injection I a water model and mathematical simulations using the Reynolds Stress Model (RSM) of turbulence. Geometries included octagonal-regular, octagonal-irregular, pentagonal and squared. A layer of oil was used to model the behaviour of tundish flux during steel flow. Fluid flows in a tundish using these geometries were compared with that in a bare tundish. Experimental and simulation results indicate that the flow in the bare tundish and a tundish using turbulence inhibitors open large areas of oil due to strong shear stresses at the water-oil interface but the squared inhibitor. These phenomena are explained by the high gradient of the dissipation rate of the turbulent kinetic energy using the squared inhibitor. Using this device the kinetic energy reports a high gradient from the tundish floor to the free bath surface as compared with other geometries.

Jan 1, 2006

By Peter Altounyan

Goedehoop Colliery in the Witbank Coalfield of South Africa produces some 8 million tonnes of coal from fully mechanised room and pillar mining methods, using resin anchored bolts as roof support. Investigation of the quality of the installed bolts resulted in the finding that it was possible to pull out fully encapsulated roofbolts. This led to a drive to improve the quality of installation by making it easier to install a roofbolt correctly and more difficult to install incorrectly, whilst at the same time achieving high bond strength. The method of installation which was investigated, developed and implemented is known as &apos;spin to stall.&apos; The roofbolt is pushed through the resin capsule to the top of the hole and then spun to mix the resin, until the increasing resistance to rotation exceeds the breakout limit on the bolt torque nut. The nut then runs up the bolt thread and is tightened to the roof as the drill stalls. This procedure is simple and avoids human factors such as non adherence to &apos;spin&apos; and &apos;wait&apos; times which contribute to poor installation with conventional methods. However spin to stall installation has been avoided in the past because of concerns over damage to the resin bond. This paper reports on the efforts made to investigate and understand the factors involved, and the progress made in overcoming the problem of resin damage so that the advantages of this installation method can be realised.

Jan 1, 2003

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974