Search Documents

By F. Robert Hollo

Programmable controllers have achieved remarkable acceptance over the relatively few years since their introduction. They provide some unique advantages over conventional relay and solid-state logic, which they often replace. Programmable controllers are discussed in both conceptual and functional terms, followed by an exploration of their applicability to material handling tasks with particular emphasis on conveyor systems.

Jan 1, 1973

By J. Suiter, H. F. Ryan

H. F. Ryan and J. Suiter (CSIRO)—In this paper the authors have presented "a physical model which has as its central hypothesis the solution strengthening of regions along grain boundaries in the order of tens of angstroms thick", and their calculations have used 40Å as the zhalf-width of this boundary region. Selection of this value by the authors suggests that they were unaware of a number of recent field-ion microscope observations of grain boundary structures (e.g., Refs. 29 and 30). The accompanying figure, Fig. 9, shows a portion of an ion micrograph of a tungsten specimen containing a grain boundary, and the regular arrangement of atoms in various crystal planes in each grain can be seen, except in the boundary zone which is not more than two atom diameters in width. Since it is expected that solute atoms will segregate only to the region where the lattice is disturbed, it would seem that a value of 4Å for the half-width of the boundary region would be more appropriate than the value of 40Å assumed by the authors. If the former value is used in Eq. [8] of their paper to obtain curves showing solute concentration in the grain boundary as a function of temperature, the resulting curves differ significantly from those obtained by the authors. Although there are only relatively slight changes in the regions corresponding to higher temperatures (i.e., grain boundary concentrations of approximately 1 at. pet), at lower temperatures the curves are no longer realistic. For example, the curve corresponding to u = 7000 cal per mole gives a solute grain boundary concentration in excess of 100 pet at a temperature of approximately 360°K, and "flattens out" at a grain boundary concentration of about 300 pet! Similar results are obtained with each of the other curves. Ion microscopy of dilute solid-solution alloys has shown that solute atoms give rise to image points which in most cases are of higher intensity than those of the solvent atoms.31 If the same behavior occurs when the solute atoms are present in much lower concentrations then ion microscopy should provide a sensitive tool for studying the segregation of impurities to the grain boundary regions. Although many grain boundaries in tungsten have been examined after different thermal and mechanical treatments, there has not been, as yet, any systematic study of such segregation. In general the micrographs show no clear indications of marked grain boundary segregation, but occasionally areas are found where the grain boundary contains an appreciable number of image points of high intensity in a very narrow zone, see Fig. 9. If it is assumed that these correspond to impurity atoms then it is possible to estimate the impurity concentration both in the grain boundary and within the body of the grains. Application of this method (to a larger area

Jan 1, 1965

By J. Duncan Keppie

"Auriferous quartz veins occupy zones of dilation. Foldgenerated dilation zones are systematically distributed and are dependent upon the folding mechanism. Comparison of natural and theoretical folds indicates that different mechanisms operated in the Halifax and Goldenville formations.In the slates of the Halifax Formation, the folds are of similar type and internal strain is most intense in the limbs. This internal strain is probably accommodated with little or no dilation.In the meta-sandstone and slates of the Goldenville Formation, a combined flexural and tangential longitudinal strain mechanism, modified by pure strain, produced the folds. Tension fissures produced by this mechanism are: (a) saddle 1'eef veins in slate horizons, (b) veins normal to bedding in meta-sandstone layers in the fold hinges,(c) veins along faults in the cores of tight fold hinges and (d) zones of en- échelon veins in slate honzons in the limbs of folds. Because veins in fold hinges (a, b and c above) account for most of the gold production in the Meguma Group, other factors controlling the distribution and size of these veins are summarized below.1. The size of saddle reef veins is controlled by the curvature of the fold hinge. Thus, a Curvature Index greater than 600 degrees indicates a promising prospect, where"

Jan 1, 1976

By Xinghui Meng

The leaching behavior of platinum powder in .iodide solutions under oxygen pressure in an autoclave was investigated. Ammonium salts were added to the leaching solution at neutral pH as a key lixiviant for platinum. The effect of temperature, partial pressure of oxygen, concentration of iodide and of arttmonium salts on the dissolution rate of platinum was examined. Under experimental conditions, the leaching behavior of platinum powder exhibited a complex reaction mechanism. A precipitate was found during the leaching process and was identified to be platinum ammine iodide, Pt(NH3hI4. The dissolution rate was controlled by a series of chemical reactions, the equilibrium concentration of the platinum ammine iodide being responsible for the ultimate limit to the recovery.

Jan 1, 1996

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By W. G. Sinclair

The North Texas district incorporated in this paper corresponds with the Railroad Commission's District No. 9, and includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger, and Young.† Table I,Oil and Gas Production in North Texas District, has been changed to conform with the nomenclature of pools designated by the Commission in order to facilitate compilation of the data, since most of the companies operating in the area are coming more and more to recognize one central authority in the matter of naming each new oil pool. No effort is being made to discuss the structural characteristics of the region, since it is generally known by oil men that most of the oil and gas comes from Pennsyl-vanian, with some of less importance from the Mississippian and Ordovician. Development during 1944 There were 1550 wells drilled during 1944, an increase of 450. Of this number, 677 were completed as oil wells, and 11 as gassers. Production increased 1,505,025 bbl., making the year's total 43,172,005 bbl. of oil having an average gravity of 40". Development generally, however, was somewhat disappointing. The 47 new pools, extensions, or new pay horizons in old fields, had a combined initial production of only 19,146 bbl. It is estimated that these wells added approximately 10,000,000 bbl. to the reserves. The largest single addition to the reserves was in the Caddo conglomerate in the Hildreth pool, Montague County. During the year, 66 wells were completed as the result of three extensions, I to 136 miles west, northwest and north of the field. Young, Archer, and Clay were the most active counties. Eleven new potential - oil fields were developed in Young County, nine in Archer and nine in Clay. Outlook for 1945 In spite of the fact that exploration as a whole was disappointing in 1944, prospects for increased development are bright for 1945. At the close of last year, 2.1 geophysical crews were operating in the district, which, together with the Ohio Oil Company's No. I W. R. Ross, a wildcat Strawn discovery in King County, 1 1/2 miles beyond the west boundary of district 9, stimulated a lease play extending over four counties. Two of them, viz., Foard and Knox, are in the area incorporated in this report. Acknowledgments The writer is indebted to Mr. C. W. Hanley, Zone Agent of the North Texas District, and Mr. William M. Lourcey, head of the Land, Leasing and Scouting Department for the Gulf Oil Corporation, both of Fort Worth, Texas, for permission to prepare this paper.

Jan 1, 1945

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By A Logan, B Cuthbert

Brown and Chitombo (2007) indicated that during the last two decades, the international mining industry has been using mainly mass mining methods to extract safely and economically some of the important commodities such as copper, diamonds, gold, iron and nickel. Mass mining may be implemented either on the surface through large open pits or underground using mining methods such as sublevel, block and panel caving. Developments in the last ten years have demonstrated that caving methods can be applied successfully in strong orebodies at greater depths and in increasingly challenging geotechnical environments for which more traditional mining methods would be unsuitable, unsafe and/or uneconomic. These underground mass mining challenges require æfront endÆ investigation and analysis, robust engineering design and disciplined implementation and operation. Newcrest Mining Limited has focused its efforts on the development of gold/copper projects of substantial scale and margin. To help achieve this, the company is applying and further developing mass mining methods. These include large-scale open pits (OP) and underground mining methods such as sublevel (SLC), block (BC) and panel caving (PC). Block and panel caving now offer economies of scale opportunities for Newcrest to achieve high production rates at lower production costs; thus enabling the exploitation of mineral endowments at higher margins. This paper discusses the practical aspects of caving technologies that Newcrest continues to develop through its expertise at Telfer and Ridgeway SLC operations, Ridgeway Deeps BC and Cadia East PC projects.

Jan 1, 2008

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.' The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By J. B. Clark, A. J. McEvily, R. L. Snyder

The nonuniform distribution of precipitate particles has been recognized as a leading factor contributing to the relatively low fatigue resistance of aluminum alloys. The structure of many of these alloys is characterized by narrow precipitate-free zones adjacent to the grain boundaries. Alloys with such zones exhibit a tendency for brittle inter crystalline fracture. The interrelation between this type of structure and mechanical properties was investigated in an Al-10 wt pct Mg alloy. It was found that deformation during fatigue occurs preferentially along these zones and cracks initiate there. In Al-10wt pct Mg, the zones were found to be supersaturated even after extensive general precipitation and are due to the absence of proper precipitate nuclei in the region near the grain boundaries. Cold working the alloy prior to aging improves the mechanical properties by inducing precipitation within the zones and also by jogging of grain boundaries. The mode of fracture is changed from brittle inter crystalline to more ductile trans granular fracture. THE process of fatigue is highly structure sensitive, with the strength of the whole often dependent upon some localized discontinuity, either geometrical or metallurgical in nature. Much has been learned about the role of geometrical discontinuities, e.g., notches, in fatigue, but with the exception of the effects of inclusions or the shapes of carbides, relatively little is known about the specific effects of discontinuities in metallurgical structure such as nonuniform precipitation. In most age-hardening aluminum alloys, metallo-graphic studies have shown that the extent of precipitation adjacent to grain boundaries is much less than that which occurs in the interior of the grains. The width of these almost precipitate-free regions, which are sometimes called denuded zones, and the extent of solute depletion within them, are dependent upon the particular alloy and its aging treatment. It has been observed1 that these zones are relatively soft with the result that plastic deformation takes place preferentially within them. It has also been shown 2-4 that there exists a tendency for intercrys- talline cracking in fatigue when such zones are present. It is of interest to note that Broom et al.2,3 were able to reduce the incidence of this type of failure in an A1-4 wt pct Cu alloy by stretching the material 10 pct prior to aging. In the present study, the effects of precipitate-free regions on the fatigue properties of an A1-10 wt pct Mg alloy were studied in detail, and the effects of deformation prior to aging on the nature of the precipitation process as well as on fatigue properties were also investigated. MATERIAL AND PROCESSING An A1-10 wt pct Mg alloy was selected for this study, because it was known that well-defined precipitate-free regions along the grain boundaries are readily obtained in this alloy after aging at 200oC.5 The starting materials were 99.998 pct A1 and singly sublimed magnesium of about 99.9 pct purity. The aluminum was induction melted in a graphite crucible, and then the magnesium addition was immersed until dissolved. Chlorine gas was then bubbled through the molten alloy for 4 min to degas the melt, after which the melt was cast at a pouring temperature of 730" to 760°C into a cold, graphite-coated, tapered steel mold. Since A1-Mg alloys are difficult to homogenize,5 special care was taken to obtain a uniform composition. Two-in. cubes were cut from the ingot and heated at 446°C for 30 min. These cubes were then hot forged approximately 35 pct in each of the three cube directions and homogenized for 16 hr at 446°C. Sheet specimens were then obtained by pressing 40 pct and rolling 35 pct per pass with reheating between reduction steps to a final thickness of approximately 0.10 in. The sheet was then solution treated for 16 hr at 446°C and water quenched. The age hardening behavior of this material at 200°C was then determined, and the results are shown in Fig. 1. The age hardening of this alloy when subjected to cold work prior to aging is also shown in this figure. Preliminary work indicated that extensive deformation after quenching was required to affect drastically the precipitate-free regions in this alloy, and a rolling reduction of 50 pct was chosen. For purposes of comparison the following three conditions were studied: a) Solution treated, quenched, and aged 20 hr at 200°C

Jan 1, 1963

By E. J. White

Data from oil well logs and core analyses were used to quantitatively evaluate formation porosity and water saturation of heterogeneous carbonates and to study the pore geometry and performance characteristics of cores from these formations. Logs and cores from the Madison limestone from 233 wells in three fields in the Williston basin were used in the investigation. A comparison of log and core analyses shows that log porosities are consistently larger than core porosities, and the differences are correlatable with core porosity ranges. Water saturations from logs are usually smaller than the corresponding core saturations by summation of fluids, but the difference is attributable to mud filtrate invasion into the cores during drilling. Petrophysical studies show that the low permeabilities and high residual water saturations in these reservoir rocks are due to their fine crystalline texture and complex pore geometry (heterogeneity). It is concluded that both log and core analyses must be used for reliable evaluation of these carbonate formations.

Jan 1, 1971

By Shawn Healey, Ray Norcross

"Site IdentificationNew Britannia MineA 50/50 WX Gold Inc. - High River Gold Mines Ltd. Joint VentureTVX Gold Inc. is the OperatorLocationThe New Britannia Mine is located in the town of Snow Lake, Manitoba, which is situated between Flin Flon and Thompson, 420 miles north of Winnipeg.Brief Description of OperationNew Britannia Mine processes 2000 tonnes per day at an average grade of 4.5 g/t. Mill recoveries are currently 91 YO, accounting for forecast of 98,000 ounces for 1998.New Britannia Mine's mill complex incorporates conventional crushing, grinding and carbon-in-pulp technology. The design capacity of the New Britannia Mine mill is 1850 tonnes per day. The mill has processed upwards of 2300 tonnes per day, with no required upgrades.Gold recovery averaged 89.8% for 1997 compared to the planned 87% recovery expected from projected metallurgical test work. Year to date recovery mid December 1998 stands at 91.1 %Cash costs for the 1998 year to date were down to U.S. $221.49 per ounce, down 12% from the 3rd quarter of 1997. Milling costs for 1998 YTD were at Cdn. $9.38 per tonne and Cdn. $73.50 per ounce.Geology - (Orebody Description)The Snow Lake gold deposit is located within the Aphebian Flin Flon / Snow Lake Greenstone belt. This belt is composed of an assemblage of poly-deformed volcanosedimentary supercrustal sequences intruded by pre and sin tectonic ultra mafic and mafic intrusions and sin to post tectonic granitoid.The principal gold bearing rock at the New Britannia Mine is made up of quartzcarbonate material in sequence of basic and acidic volcanic rocks contained within a shear zone. The ore itself is gold associated with the sulphide mineral arsenopyrite and contains some pyrite, pyrotite, plus chalcopyrite. Proven and probable reserves at December 31, 1997 were at 4.04 million tonnes at 4.6 g/t and underground exploration continues to confirm the extension of the ore zones to depth."

Jan 1, 1999

By Gilmar Ferreira Bataglia

The possibility of parameterization of hot tensile data together with creep data is investigated, for Aluminium Alloy 7475-T7351. This study represents part of a broader research program aiming at the validation of a methodology recently proposed for analyzing both kinds of data together, considering different metallic materials. The results presented in Part 1 of this work, were analyzed according to 4 traditional methods of the literature for parameterization of creep data, namely: Larson-Miller, Orr-Sherby-Dorn, Manson-Succop and Manson-Hafferd. The compatibility of the hot tensile test results with those of creep is remarkably good, indicating the possibility of using both kind of data together also in extrapolation schemes. The criterion proposed for equivalence between hot tensile and creep data is verified to work well also for this kind of material, under the present experimental conditions.

Aug 8, 2018

By G. A. Frame, J. G. Patterson

The 24,000-tpd Frood-Stobie mill grinding circuit operation and control are described. Changes implemented during the past three years to improve grinding efficiency and capacity are discussed.

Jan 1, 1971

By F. L. D. Cloete, M. C. Coetzee

This study was aimed at a comparison of the efectiveness of a new axial-flow type of mixer impeller (the Prochem design) with the traditional inclined-blade turbine. The intended application of the mixers was in carbon-in-pulp plants for the extraction of gold from cyanide-leached pulps. The first part of the project involved water and ion-exchange resin, and measurement of the power drawn by the various sizes of impeller to fully suspend the resin. The rate of reaction between the resin and the solution was measured as a function of the power input to the mixer. In the second part of the project, use was made of activated carbon, silver cyanide solutions, and ore pulps. The rate of absorption of silver from the solutions and pulps was determined, as well as the rate of attrition of the activated carbon caused by the various impellers in clear water. The Prochem design of axial-flow impeller was shown to fully suspend solids at only one-quarter of the power requireabyan inclined-blade turbine of similar size. The axial-flow pattern produced was responsible for the more uniform vertical concentration profile of suspended beads produced by the Prochem design. These measurements verified the observations of other researchers that the rate of reaction is not affected by the ;design of impeller provided that al the solids are fully suspended. The Prochem design of impeller therefore achieved the same reaction rate as the conventional turbine at a quarter of the power input. The atrition rates of activated carbon could be correlated, in terms of the energy absorbed, by the same equation for al the impellers. Higher concentrations of activated carbon increased the amount of carbon fines produced. These results emphasize the importance of designing mixers for minimum power consumption.

Jan 1, 1989

By Dengfu Chen, Huabiao Chen, Yunwei Huang, Mujun Long, Youguang Ma, Lintao Gui

In the current work, a three-dimensional model coupling turbulent flow, heat and solute transport was developed to investigate the solute transport and redistribution in the mold of slab continuous casting where the Reynolds number is very high and the molten steel flows strongly. The conservation equations of momentum, energy and species for a multicomponent system which includes solute element C, Si, Mn, P, S were solved with the commercial software ANSYS Fluent. The parameters used in the model are based on the actual continuous casting. The fluid flow, temperature distribution and solute elements distribution were analyzed. Results showed that negative segregation occurred near the strand surface, and the species concentration reached a peak value at the solidification front during solidification. The segregation degree of solute element S is higher than the other solute elements because of its lower equilibrium partition coefficient. The species concentration in the liquid pool is homogeneous because of the turbulent flow effect.

Jan 1, 2015

By A A. Struthers, A D. Farmer

Power ultrasound may be applied to enhancing the processing of minerals. The enhanced performance is achieved through the very localised high-energy release at the mineral surface from the collapse of cavitation bubbles produced by power ultrasound. This gives rise to two effects: initially, the rapid cleaning of mineral surfaces û of oxidation products and coatings of fine adhering gangue minerals û and the attenuation of the boundary layer at the mineral surface during leaching, which allows fresh leachant to contact the surface more readily. Work carried out at CSIRO in conjunction with Tiwest Joint Venture has demonstrated that it is feasible to apply ultrasound to the leaching process in order to enhance the removal of contaminating minerals. When applied to the production of synthetic rutile from reduced ilmenite produced by the Becher process, the use of ultrasound proved beneficial to both the aeration and the final acid leach process. The effect of ultrasound was less marked in the case of the aeration process, once the method of introducing and dispersing the air was optimised. In the subsequent acid leaching step of the Becher process it was found that the application of power ultrasound could reduce leaching time to about one quarter of the time required when only agitation was employed. Projected capital and operating costs, based on currently available commercial equipment, are also presented, and indicate that the use of ultrasound is commercially as well as technically feasible.

Jan 1, 2001

By D Giles, A C. Bailey

In the first 20 years of the 21st century, just over 20 per cent of Australian mineral exploration expenditure was dedicated to iron ore, totalling >A$8 billion and >30 million metres of drilling (Australian Bureau of Statistics, 2021). Improvements in the cost, efficiency, safety, reliability and data quality of drilling have the potential to deliver significant productivity improvements, increasing the probability of discovery and reducing the time from discovery to mining. Currently in its third year of research, Mineral Exploration Cooperative Research Centre (MinEx CRC) is focused on a new set of exploration tools and new ways to deploy those tools which recognise the fundamental importance of collecting quantity and quality data from the subsurface, to enable exploration success for all minerals, including iron ore. MinEx CRC is focused on developing more productive, safer and environmentally friendly drilling methods to discover and drill-out deposits. This includes pioneering work on Coil Tube (CT) drilling technology and innovations in Diamond and Reverse Circulation (RC) drilling techniques aimed at improved drilling optimisation and automation. In parallel, MinEx is developing new technologies for collecting data whilst drilling. This is being undertaken in four separate industry-led projects utilising geophysical, seismic, downhole analytical and 3-dimensional (3D) modelling improvements. A National Drilling Initiative (NDI) is also underway, with two drilling programs completed in 2020. The NDI is a world-first collaboration of Geological Surveys, researchers and industry, which undertakes drilling in under-explored areas of potential mineral wealth in Australia and provides a test-bed for new mineral exploration technologies.

Nov 8, 2021