Search Documents

By Liu Y, Campbell K. R

The paper shows how breakage parameters may he extracted from laboratory batch grinding results and how they may used with reference full-scale hall mill circuit data to estimate the likely size distributions of values and gangue in a full-sca

Jan 1, 1997

By F. J. Sotillo

Mining in Peru is mainly concentrated on metallic and polymetallic ores of gold, copper, lead, zinc, silver, tin, iron, etc. However, little has been done to develop extensive and rich non-metallic or Industrial Minerals deposits with the exception of some silica and phosphate deposits. This paper presents the characterization and metallurgical studies for the development of a feldspar deposit. These studies showed that the special characteristics of the ore, such as high porosity, high Al2O3 content, low clays content, and sized material allowed us to obtain commercial products applying relatively simple and low cost concentrating unit operations. The characterization studies showed that the feldspar products contained no quartz and about 90% of albite (NaAlSi3O8). The 14x40-mesh size fraction product analyzed 5.91% Na2O, 22.56% Al2O3, 65.73% SiO2, 0.65% K2O, 6.50% CaO, and 0.40% Fe2O3; whereas, the 40x150-mesh size fraction product analyzed 6.22% Na2O, 24.30% Al2O3, 60.80% SiO2, 0.91% K2O, 7.06% CaO, and 0.54% Fe2O3. These products could be used for manufacturing glass, ceramics, refractory, and filters in different applications. In addition, Middlings, could be used as insulation material due to its porosity (bulk density of 0.828 Kg/dm3), analyzing 4.46% Na2O, 15.7% Al2O3, 67.2% SiO2, 2.57% K2O, 3.94% CaO, and 4.24% Fe2O3. The material showed a sphericity of 0.77, a roundness of 0.68, and acid solubility of 13.3025% on only washed and 2.72% effective for clean material suitable for use in these applications. No selective accumulation of the valuable mineral was observed at any specific size fraction. However, iron and titanium bearing impurities trended to concentrate in fine fractions (minus 70 mesh -212 µm-). Metallurgical studies demonstrated that this feldspar ore required sizing at 14x40 mesh and 40x150 mesh to render commercial products. In the case of the 14x40-mesh size fraction, the process involved magnetic separation, gravity separation, and flotation for feldspar (direct flotation) using a blend of primary and condensate amines. However, the reverse flotation for mica-biotite and iron bearing minerals was also possible using petroleum sulfonate. The metallurgical process for the 40x150-mesh size fraction required magnetic separation and reverse flotation of iron and titanium bearing minerals, the feldspar being reported in the sink material. Commercial products from this feldspar deposit for glass, ceramics, refractory, and filtration; and for the manufacturing of insulation material were obtained.

Feb 23, 2014

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

THE program for the 126th meeting of the Institute, to be held in San Francisco Sept. 25 to 29, 1922, is being prepared by the General Arrangements Committee of the Local Section and its details are not yet ready for announcement. The program, however, has developed to a sufficient extent to permit members to decide whether they wish to attend or not. Briefly stated, Monday, Sept. 25, will be devoted to technical sessions which will be held at the Engineers Club, and there will be as many sessions as may be required to present the papers available, some of which are listed below. Under the registration fee plan (see July magazine) entertainment expenses during the week in San Fran-cisco will be borne by those in attendance, not by local members alone. Members who expect to attend the San Francisco meeting, but who will not accompany the President's party, will please notify C. H. Fry, Secretary of the San Francisco Section, 625 Market St., San Francisco, Cal., of their intention.

Jan 8, 1922

By Athorn Mary-Lee, Randall A. Snowdon

During the development of the Selby Coalfield, UK, a Robbins full-face tunnel boring machine (TBM) and a Thyssen Titan roadheader were used to drive a pair of parallel spine roadways. This paper presents a summary of the comparative operational and cutting performance of both the Titan road- header and the Robbins TBM. Statistical techniques were employed to identify relations between machine performance and geotechnical parameters.

Jan 1, 1986

By Ehab Gomaa, K. A. El‑Nagdy

Backfilling material such as tailing (mine wastes) mixing with cement or gypsum has grown throughout the world’s underground mines. However, despite their growing popularity, the typical hydraulic and mechanical fill types utilized in many mines still exist. Deep underground mining has increased due to the lack of commercial minerals nearby. Mine wastes were considered the main part of backfilling to prevent environmental pollution, ground subsidence after mine abandonment, and mine collapse during deeper extraction phases. The cemented backfill technique is the principal technique used in underground mines, which include cement with fly ash and/or filter dust, cement with tailing material and fly ash, gypsum with fly ash, and synthetic anhydrite with fly ash and have been reviewed. It has concluded that a backfilling material must be selected based on further goals, available material near the mine site, and economic factors. This paper analyzes different backfill material mixtures to create a technique that will increase safety in underground mining conditions and foresees an appropriate formula that gives high uniaxial compressive strength. The multiple linear regression (MLR) on the collected data from the experimental works to construct the relationship between the uniaxial compressive strength (UCS) of the mixture and the components of the backfilling and the prediction formula for expected compressive strength was obtained. The results revealed that the predicted regression equation was robust and reliable to predict the (UCS) for the new components of the filling (cement (CE), filter dust (FD), water content (WC), and time (T)).

Oct 3, 2023

I-institute of Metals Division S. SKOWRONSKI, Chairman ZAY JEFFRIES, Vice-chairman WILLIAM M CORSE, Secretary Executive Committee J. R. FREEMAN, JR, Local Section G E JOHNSON R S ARCHER, Non-ferrous Data Sheets P. D. MERICA EDGAR C BAIN, Journal Committee L W SPRING SAM TOUR, Papers Committee F. L. WOLI H. C. JENNISON, Membership Committee Local Section Committee J. R. FREEMAN, JR., Chairman R. J. ANDERSON, Cincinnati R L. DOWDELL. Minneapolis R. S WILLIAMS, BostoI G. H. CLAMER, Philadelphia W. A SCHEUCH, Chicago R. F. WOOD, New York

Jan 1, 1923

By Stewart Gillies A D, Just G. D

An internationally recognised and uniform method for classification, categorisation and designation of mineral and energy resources is not yet available. With the increasing need for reliable and comparable coal resource data it is necessary to standardise the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can considerably improve classification quality. A review is undertaken of major classification with particular emphasis on those that incorporate limits on estimation error.A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed.Application of the classification algorithm for resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results that closely reflect the error associated with an estimate of resource quantities based on current sampling densities.lbis requires a careful geostatistical analysis with an emphasis on geological awareness. Resource category restrictions although albitrarily assigned should remain constant for all deposits being compared. This requires some engineering judgement with additional interpretation also required for isolated and peripheral block.

Jan 1, 1990

By Behdeen Oraee

Constructing tunnels underground is generally described as a high-risk activity because conditions in the surrounding area tend to be unpredictable. This would and can create unique dangers in every situation. It is important to gain a deep understanding of the risks associated with tunneling in order to reduce the likelihood of their occurrence and severity of their consequences should they occur. For this to be achieved, different risks should first be evaluated and ranked according to their relative importance and criticality. The Amir Kabir tunnel is considered one of the most dangerous tunnels in Tehran, Iran, in terms of the risks involved in its excavation and their potential consequences. In particular, part T4 of the tunnel passes through a zone of different strata and also a compound of various soils. This paper studies part T4 of the Amir Kabir tunnel from a risk analysis and risk management point of view. In doing so, factors increasing total cost, causing delay in the project completion time, decreasing the operation rate and downgrading project quality were identified and ranked according to their importance using the aggregate primary index risk method. For this purpose, a comprehensive questionnaire was designed and completed by tunneling experts. By responding to the questionnaires, the experts determined the relative likelihood of occurrence of the studied factors and their potential consequences. As a result, the experts suggested several alternatives to reduce the risks involved in this particular study. Moreover, the experts completed new questionnaires whilst taking into account different alternatives. In the next step, the risks before and after applying the alternatives were compared. As a result of performing the said analyses, it was concluded first that the aggregate primary index risk is an effective tool in identifying the risks involved in such projects. Second, it was concluded that, by taking into account different alternatives when analyzing and ranking the risks, severity of the said risks can potentially be reduced. Also, by considering such matters when analyzing tunneling risks, the projects? efficiency can greatly increase as a result of reducing risks that threaten financial and human resources. The approach introduced in this paper, together with the methodology described, can be adopted by the mining design engineer in all similar situations. They will be of particular advantage in such methods as room and pillar mining, where the number of similar tunnels required is high.

Jan 1, 2014

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

By K. L. Komarek, P. F. J. Landler

Synthetic polycrystals of wustite were reduced ilz H2-H2O mixtures over limited roncentration ranges wiltun the wustite. field and the weight changes were continuously followed with a McBain quartz spiral balance. The reduction was. found to be controlled by a combined surface plus solid-state diffusion reaction. The solid-state diffusion had an activation energy of 38 kcal. Self--diflusioities of iron decreased with itzcreasing vacancy concentration. The activation energy of. the surface reaction runs different tor- different samples. The surface reaction-rate constan increased with increasirzg vacancy concentration. THE reduction of the oxides of iron has been studied for many years. Edstroem' has summarized the early work and has provided much information on the reduction of magnetite and hematite by hydrogen and carbon monoxide. More recent summaries are those by smeltzer2 and Themelis and Gauvin.3 Most investigators have reported that the iron metal which forms the outer layer during gaseous reduction is rather porous. According to Kohl and Engel14 the formation of such a porous iron layer depends on the properties of the underlying wiistite layer, on the reaction of the gas with the wustite surface, and on the transport of matter through the wustite layer. McKewan, Quets, Wadsworth, and Lewis, and Knacke 10 have found that, if a porous iron layer is formed, a surface reaction between gas and wustite at the bottom of the pores controls the rate of reaction. Seth and ROSS 11 and Warner 12 have pointed out that the influence of the gaseous pore diffusion through the porous iron layer cannot be neglected. It has further been shown that the wiistite layer formed during reduction is dense and that transport of matter across the layer occurs only by solid-state diffusion of iron ions.13,14 The solid-state diffusion rates observed by Edstroem and Bitsianis 14 and the surface reaction rates observed by Quets eta1.' show that an interaction of the two steps in controlling the reaction rate has to be considered. In this investigation the reduction of wustite was studied with respect to the interaction of the two steps, isolated from any other effects, by reducing wustite within the wustite field from higher to lower oxygen concentrations with H2-H2O gas mixtures. A similar study with CO-CO2 mixtures has been performed by Levin and wagner.15 Fused synthetic wustite polycrystals were reduced in steps of 0.4 wt pct from 24.4 to 23.2 wt pct 0 and over a temperature range from 700" to 1050°C. A few tests were also conducted with reduction steps from 24.4 to 23.6 wt pct 0 and 24.5 to 23.2 wtpct0. The Fe-O phase diagram is shown in Fig. 1 where the composition of the gas phase in equilibrium with the condensed phases is plotted as pct H2 vs the temperature. A careful study of the literature led to the conclusion that the fully drawn equicomposition curves (in wt pct O) in the wustite field used by Edstroem 1,16 and other authors needed some correction. Based on results by Darken and Gurry17 (shown as open circles) and on some of our own data, four corrected curves for 23.2, 23.6, 24.0, and 24.4 wt pct O were calculated (drawn as dashed lines in Fig. 1) which should replace the fully drawn equicomposition curves. MATERIALS AND APPARATUS Materials and Specimen Preparation. Wustite was prepared from iron sulfate (Fisher Scientific Co., New York) which had a purity of over 99.92 pct, with small amounts of manganese, copper, and zinc adding up to 0.03 pct. From the aqueous solution iron oxalate was precipitated and decomposed to magnetite according to Economos. 18 The magnetite powder was pressed into cylinders and sintered in vacuum at 900°C for several hours. The sintered compacts were placed in a platinum crucible of 2.5 cm diam which was fitted into a high-purity alumina crucible and then inserted into the center of the graphite heating element of an electric resistance furnace.lg The furnace was evacuated to below 1 p Hg and the magnetite sample was slowly heated. The evolution of gases during heating deter-

Jan 1, 1967

By S. W. Mao

Hydrologic and economic criteria figure in many obvious ways in water resources development, but they are rarely linked quantitatively, and most of the applications are pertinent only to the case-in-point. In the preparation of the Regional Plan for the massive program of ground water development in the Punjab, situations have arisen where the choice among two or more alternatives was made by analyzing the economic implications of critical hydrologic parameters. Two of these situations which are of more-or-less general interest are described herein. The first involves basic development policy -- whether ground water development should be based on the demand of the economy, or the conservation concept of safe-yield. The analysis demonstrated that mining of ground water is clearly indicated for areas where alternative supplies are unavailable. The second problem involves integrating hydrologic data into an economic model to determine optimum well design, From an analysis of all pertinent factors, a simple nomograph was derived which can be used to determine well specifications on-site during construction. The nomograph can be modified for use in any alluvial terrain.

Jan 1, 1967

By R. A. Hemstock

"OIL EXPLORATION in Western Canada has produced outstanding results in the past few years. From such successes as Leduc and Redwater on the western plains, oilmen are now moving north in the ever-widening search for oil. They are reaching new frontiers and meeting new problems presented by this vast hinterland.One of the least known but most troublesome phenomena which will be encountered is permafrost. This term relates to a thickness of soil or other superficial deposit, or even of bed-rock at variable depths beneath the surface, in which a temperature below freezing has continually existed .for a long time. This permanently frozen ground affects, in many ways, oil exploration and exploitation. Seismic records are changed, pipe lines cannot easily be ditched into the ground, formation of wax is speeded-up in tubing and pipe lines, roads are difficult to build, and foundations of buildings and even of drilling 'rigs may require entirely new methods of construction.Permafrost underlies roughly one-fifth of the entire 'land surface of the world. It covers the northerly portions of Eurasia and North America. In the area that we are here concerned with, the southern boundary of permafrost extends south of east from about latitude 59°N. on the Pacific coast across the Rocky mountains, through Great Slave and Athabasca lakes, to cape Henrietta Maria, at the junction of Hudson bay and James bay (see Figure 1). Geologists generally agree that permafrost first appeared in the Pleistocene or Ice Age as the result of abnormal ground freezing."

Jan 1, 1952

By John B. Porter

Within the last year or so, a great deal has been heard about Southern iron ; even the Eastern markets have felt the effect of the cheap Alabama ores and coals, and public attention has again been drawn to what is now getting to be an old story—the great mineral wealth of the South. The following paper is based on a report prepared several years ago for a special purpose; but since then, through association with Mr. C. B. Going in a large analytical practice and as chemists to the Queen and Crescent Railway, I have had opportunity to increase my material so greatly that the present paper is really a completely different work. I am under very great obligation to Mr. Going, without whose assistance my work would have been very incomplete, and have also been materially assisted by Mr. F. P. Dewey, of Washington, and a host of gentlemen connected with the railroads and furnaces of the South. The arrangement of this paper is not all that could be desired. Some localities of importance are very poorly represented, both in the description and the tables of analyses. This, however, was in most instances unavoidable, as the study has been done ill the intervals of professional work. I have visited almost all the localities described, and, in all cases possible, have taken my own samples, and have made careful per-

Jan 1, 1887

By Kavetsy A

In surface mining operations, the ease with which a muckpile may be dug is a dominant factor in mining efficiency. Within broad limits this is largely independent of the fragment size dis- tribution, since the equipment used to move the broken rock is generally larger than in underground mines. In such cases, muck- pile shape and voids ratio within a muckpile heavily influence mine productivity. In a particular operation, the muckpile shape after blasting should be tailored to the digging equipment being used. A front- end loader is best suited to a low, flat-lying, loose muckpile, because of its fairly good mobility and small break-out force with its bucket. In contrast, a rope shovel lacks mobility, generates a much larger break-out force with its bucket, and fills its bucket in a vertical filling motion. Therefore, it is ideally suited to well fragmented, steep faces. In situations where a dragline is used, the requirement for a suitable muckpile depends on the operat- ing scheme of the dragline. For a conventional highwall key method the preferred work- ing level of the dragline is the same as the highwall, so that the dragline may sit over its key. In this situation, the ideal muck- pile shape involves relatively little displacement of the fragmented rock, with a minimal "power trough" at the back of the blast. In throw blasting, on the other hand, it is desirable to cast as much of the spoil as possible across the pit. It is then necessary to optimize the blast design by maximizing the throw percentage under any necessary constraints (e.g. damage, vibration, flyrock, explosive cost).

Jan 1, 1988

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023

By David D. Eyer

In today's world coal market, coal quality is becoming increasingly important. Often the coal quality parameters are one of the crucial considerations in the development of a coal mine. Because of the user's tighter specifications and because of strict environmental regulations, coal producers are being called on to predict with increasing accuracy, not only the quality of their product but also the variability of that quality. This area of reserve evaluation is naturally receiving a great deal of scrutiny. Consolidation Coal Company has developed reliable and sophisticated methods for predicting coal quality, but the company's efforts continue to search for even better techniques. The following is a step-wise summary of The methods currently used by consolidation coal company, with A recent project used as an example. Two of the newer, and as yet experimental techniques will be briefly discussed.

Jan 1, 1980

By V. F. Parry

The author wishes to acknowledge the advice and criticism of A. C. Fieldner, chief, Coal Division, Bureau of Mines, United States Department of the Interior; the assistance of Durbin Van Law, consulting industrial engineer, Denver & Rio Grande Western Railroad, Denver, Colo., who furnished valuable information on trends of coal production in Utah by making available his unpublished report "Utah Coal Industry"; and the aid of J.C. Beltz, associate research chemist, Bureau of Mines, Washington, D. C., who reviewed and checked the data, and of W. S. Landers, assistant chemical engineer, Bureau of Mines, Golden, who assisted in the preparation of many of the statistical data, in this report.

Jan 1, 1942

By X. Cao, A. Birur, R. R. Chromik, J. Cuddy, P. Wanjara, J. Gholipour Baradari, T. Shariff

In this study, 3.1 mm thick Ti-5553 (Ti-5Al-5V-5Mo-3Cr) butt joints were autogenously welded using a 4 kW continuous wave Nd:YAG laser. The effect of welding speed and defocusing distance on the weld quality was investigated in terms of the surface morphology, welding defects, microstructure and hardness. Welds with full penetration were achieved at a defocusing distance ranging from -1 mm to 0 mm and welding speeds from 2.25 to 6.0 m/min. Underfill and porosity were the two main defects most frequently observed but within the optimum process window these defects could be maintained to meet aerospace specification tolerances. The fusion zone (FZ) consisted entirely of retained beta with a refined dendritic morphology. Compared to the bimodal alpha (a) + beta (ß) microstructure of the base metal (BM), the dissolution of the a phase was observed in the heat affected zone (HAZ), which led to an 11 % decrease in hardness from the BM to the FZ. To determine the tensile properties of the welded samples, an automated 3D deformation measurement system was used to measure the local strain in the weld region. The yield strength (YS) and ultimate tensile strength (UTS) increased with increasing welding speed with a highest joint efficiency of 75 % being achieved, albeit with a concomitant reduction in the ductility.

Jan 1, 2010

By Eugene Guccione

For at least a decade, the energy crisis was accurately predicted by a small number of industry people who were ignored until last year, when they suddenly found themselves accused for their "lack of planning" and "greed." With the worsening shortage of natural gas and oil, the current scramble is for alternate energy sources-which means: a big rush into coal and uranium mining. (Some big plans are also on the drawing boards regarding geothermal steam, oil shale, tar sands, and even solar energy. But developing such new industries from scratch would be difficult enough even in a healthy economic climate-which is not exactly what the country currently enjoys.)

Jan 8, 1974