Search Documents

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

The impact of moves to introduce Abori- ginal land rights was felt in the Northern Territory as early as 1972 when the Federal Government froze the processing of all appli- cations for mining interests over vacant Crown land. The Aboriginal Land Rights (Northern Territory) Act was finally proclaimed on Aust- ralia Day 1977 and since that date the mining industry and the Territory legislature have struggled to make the Act work. Despite these efforts long delays have been experienced by those required to negotiate mining and explor- ation agreements under the Act. In fact explor- ation on Aboriginal land has been effectively stiffled since the introduction of the Abori- ginal Land Rights Act. The Northern Territory government and the mining industry have both sought amendment to the Act to remedy some of its more onerous problems. These efforts have generally been fruitless. Some of the recommendations put forward by Mr Justice Toohey following his recent review of the Act would provide relief in some important areas. However, any such improvements are more than offset by a number of Mr Justice Toohey's recommendations which would severely disadvantage the vast majority of Territorians. A recent survey of mining companies seeking exploration licences over Aboriginal land indicates that many of the existing diffi- culties could be overcome without significant amendment to the Act but rather by the adoption of a positive administrative approach by the Land Councils. It is now up to the Commonwealth and the Land Councils to demonstrate that their Act can work without crippling the Northern Territory economy and its mining industry.

Jan 1, 1984

By J. S. Long

A finite-difference model using a digital computer was constructed to assist in the water management of a proposed oil-shale mining operation in the Piceance Basin in Colorado. The presence of ground water is both a detriment and a benefit for development of the resource. On one hand, dewatering is required because permeable zones are present in and above the oil-shale sequence, and rich oil shale at the proposed mine is as much as 457 m (1500 ft) below the water table. On the other hand, ground water is the most feasible source of water for processing the oil shale. A ground- water model was constructed to simulate the development of an environmentally acceptable water-management system that will satisfy both the mine-dewatering requirements and the water-supply requirements for processing. The ground-water model discussed in this chapter was constructed for the Rio Blanco Oil Shale Co. (RBOSC) by International Engineering Co., Inc., a subsidiary of Morrison-Knudsen Co. The model was applied to evaluate dewatering and water control systems for several open-pit mining plans initially investigated to develop Federal Lease Tract C-a. A collateral application of the model analyses was to project effects of the proposed dewatering operation on the regional ground-water regime in connection with a permit acquisition program by RBOSC. Subsequently, RBOSC has completely changed its mine development plan and has adopted modeling and related techniques more suitable for study of that plan and dewatering operation. The authors of this chapter are solely responsible for the contents and conclusions.

Jan 1, 1979

By Lloyd Williams

1. Reserves have been estimated for three coal beds in Bledsoe County, Tenn.: Morgan Springs, Lantana, and Sewanee. The Richland and Nelson beds occur in Bledsoe County also, but there was not enough information on them for making an estimate of reserves. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated at 43 million tons as of January 1, 1954. Of this total, 22 million tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves deter-mined by this investigation.

Jan 1, 1956

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By J McNee

Pike River Coal Limited (PRCL) is developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine is being developed to extract a coking coal deposit of the Brunner Seam, some 46 km northeast of Greymouth, using a combination of continuous miners, road-headers and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumped down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.   PRCL faces significant challenges to achieving the goal of cost effective production. The remoteness, high rainfall (greater then 6 metres per year on average), temperature variation and restrictions on access to this subalpine environment have driven the project to develop some distinctive solutions. These include the establishment of survey control in such a difficult environment with vertical and sub-vertical rock faces, significant vegetation and steep slopes by using helicopter survey, aerial photography and LIDAR (Light Detection And Ranging) aerial survey. PRCL has also commenced designing the placement of the main ventilation fans in an underground chamber in the stone drive.

Jan 1, 2007

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1998

By A. Boltax

Precipitation processes occurring during both furnace cooling and aging of copper-iron albys were studied by means of electrical and magnetic measurements. On furnace cooling, two distinct stages in the precipitation process were detected; one occurring above and the other below 850° C. The kinetics of precipitation from quenched alloys were studied between 200° and 700°C. The reaction appears to be consistent with the concept of tmcleation of precipitate particles at dislocation loops formed by the clustering of quenched-in vacancies. A study Of in copper-iron alloys is particularly interesting because the combination of magnetic and electrical properties in these allovs provides a quantitative means of following the course of the precipitation reaction. (The details of precip-

Jan 1, 1961

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

By P. E. Phillips

INTRODUCTION Rocky Mountain Energy is the mining subsidiary of the Union Pacific Corporation, and has been active m uranium exploration since 1966. Since 1970, RME's uranium activities have been funded 50% by Mono Power, the fuels supply division of Southern California Edision. RME and Mono recognized the need for development of new methods for recovering low grade uranium deposits, and contacted Halliburton Services in regard to in situ leaching, because of Halliburton oil industry experience. As a result, a joint venture between the three parties was formed in 1974. BEAR CREEK The first ISL test was at the Bear Creek deposit in the Powder River Basin of Wyoming, about 60 miles north of Douglas. The mineralized sand is the tertiary Wasatch formation, which is an arkosic sandstone. The sand typically contains about 10% clay. The predominant clay being montmorillonite with some kaolin and illite. The roll front type trends occur along the flanks of old stream channels. This deposit was being considered for exploitation as an open pit mine. Routine amenability testing indicated it was quite amenable to a conventional acid leach, consuming about 50 lbs. of sulfuric acid per ton of ore in an agitation leach, while recovering more than 95% of the uranium. Hydrology testing indicated a permeability of about 1 darcy. The groundwater has a pH of about 8. 0 and TDS of about 1200. Test Facility The Bear Creek test was a summer-only operation, with no effort towards weather-proofing. Uranium was removed from the recovered leach solution by fixed bed ion-exchange columns. Loaded resin was eluted with strong sulfuric acid. The recovery plant was designed for simplicity of operation, with little concern for the grade or form of the yellowcake product. The plant was constructed of PVC piping and valves, fiberglass reinforced tanks, and stainless steel pumps. All waste streams were directed toward a lined evaporation pond. Wellfield The test pattern was a 30 foot radius 5 spot, with wells fully penetrating the 30 foot ore sand to a total depth of about 165 feet. The injection wells were three-inch PVC with slotted casing, while the producer was eight-inch I. D. , with a stainless steel screen. The eight-inch well was necessary in order to accommodate a six-inch stainless steel pump. Wells were cemented using cement baskets, at the top of the sand, to contain a latex acid resistant cement. Leach Conditions The lixiviant generally contained from five to seven gpl sulfuric acid, and about 0. 5 gpl hydrogen peroxide. The pH was generally 1.4 and EMF was usually -550 millivolts. Injection rates were rather variable from well to well, with a total injection rate between 12 and 25 GPM. Production rate was set at 25 GPM, since the production pump could not be throttled more than that. Approximately two pore volumes of solution were injected during the three-month test. Leach Results Injectivity was quite variable, but was generally rather poor, because of poor completion techniques. The problem stemmed from injecting before the injection wells had been completely cleaned of drilling mud. Pregnant solutions averaged about 50 ppm U308, with groundwater dilution varying from 10 to 50%, depending on the injection rate. Injectivity did decline with time, probably as a result of contamination of the well faces. A total of 1000 lbs U308 had been recovered when the test was shut down. This probably represented about 10% of the mineral under leach.

Jan 1, 1979

By Neal Harries

Ground movement is normal in open cut mining operations, mainly caused by excavation response and blasting. Movement of the ground can be acceptable provided it is not unexpected and catastrophic. However, in steep mine walls and the very large open pits being developed today the consequence of slope collapse can be catastrophic. Such risks can be minimized at the planning stage by reducing slope angles, but this carries a very high cost. Also, instabilities which develop whilst mining can lead to ore reserves being quarantined, which represent a high cost to the mining operation. In spite of such safety measures, unexpected failures have occurred in the past. These issues motivated the development and production of the slope stability radar (SSR). There are currently over 80 GroundProbe SSR systems deployed in metalliferous and coal mines in 17 countries. The unexpected failure of rock walls at mining sites is a major cause of death and serious injury. Slope failure is also one of the major causes of economic and production losses. An unexpected wall failure can bury critical equipment. It also disrupts the mine plan. It is common to cease mining for several days or weeks following a wall collapse due to uncertainty over stability. Direct economic losses in remediation alone can easily exceed $1,000,000 per incident. The economic costs of injury or fatality are much higher including closure of mines during the incident investigation process. Massive wall failure can result in direct and indirect costs measured in millions of dollars. This paper will present some recent case studies of the SSR operation in open cut mines in North America, including Thompson Creek Mining Company (Idaho), Smoky Canyon Mine (Idaho), and a general case study on extreme cold weather use of the SSR.

May 1, 2009

By M. S. King, B. N. P. Paulsson

Four vertical boreholes in the vicinity of an electrical heater simulating a canister of nuclear waste in a granitic rock mass have been logged with an acoustic borehole sonde before and after thirteen months' heating. Excellent control of the structural geology and fractures present in the rock mass was provided by the considerable amount of oriented core recovered from the four boreholes used for acoustic logging and the large number of others used for a variety of rock mechanics instrumentation. Compressional and shear-wave velocities were measured as a function of stress on some twenty core samples, water-saturated and dry, which were recovered from the four acoustic logging boreholes. Further control was provided by a cross- hole acoustic monitoring program conducted before, during and after heating between the same four boreholes, and by measurements of acoustic velocities in an isolated block of granite in the same heater drift, which was subjected to an increase in temperature and to changes in uniaxial stress. It is concluded from the acoustic logging tests, taken in conjunction with the acoustic cross-hole and heated block experiments, that acoustic techniques: 1. Provide a means for locating and delineating systems of weakly- bonded or open fractures within the rock mass; 2. Provide a sensitive means for monitoring a rock mass for changes in moisture content or structural damage to the rock fabric induced by thermal or mechanical loading; 3. Together with the rock bulk density yield the elastic constants of the rock mass.

Jan 1, 1982

By J. K. Richmond

This is a progress report summarizing more than 5 years of a long-range Bureau of Mines research program. The purpose of this program has been to investigate the fire and explosion properties of Green River oil shale in the Bureau's Experimental Mine, in laboratories, and in the field. The lean limits of explosibility of oil shale dust, by small-and large-scale tests, are reported as a function of grade, ignition source, and particle size. A limited number of laboratory tests on the autoignition of oil shale dust layers and the spontaneous combustion tendencies of oil shale are described. Moderate-scale rubble fire tests were conducted to determine flame spread rates as a function of ventilation flow. With the aid of a system to continuously monitor methane emissions in a deep oil shale mine, the characteristics of the methane flow are reported as a function of ventilation and blasting procedures, and are compared with gas yields from core samples. Tentative predictions as to the emission of the methane to be expected in deep oil shale mines, far from the outcrop, are offered. Brief reference is made to a parallel investigation into the fire and explosion hazards of oil shale mining and processing by a Bureau contractor; detailed results of the latter investigation are to be found in the contractor's reports.

Jan 1, 1982

With one shaft almost completed and another shaft being sunk, the scope of the Saskatchewan potash area is beginning to come into focus. Some 18 companies have reportedly leased more than four million acres to explore potash possibilities. PCA, farthest along, is located about 15 miles southeast of Saskatoon, and IMC has its project underway near Esterhazy in the eastern edge of the province. U. S. Borax and Chemical Corp. is also reported exploring the area. The field lies in the middle Devonian geological formation which was probed by oil companies along the 200-mile area across the province. Extensive examination began after World War II and deep drilling was started a few years later.

Jan 5, 1958

By Eleazar Salinas R., Miguel Perez L., J. Cesar Juarez T., Martin Reyes P., Eduardo Cerecedo S., Isauro Rivera L., Francisco Patino C., Juan Hernández A.

"A complete characterization of burrows from Mining district of Pachuca - Real del Monte, in Hidalgo state Mexico, was done. These kind of residues had not been formally characterized, founding an average chemical composition of 70.43 % wt. of Si02, 7.032 % wt. of Ah03, 2.69 % wt. of Fe20 3, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 1.01 % wt. of MgO, 0.26 % wt. of Ti02, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 g/ton of Ag and 0.6 g/ton of Au; In the same way, the residues present as majority mineralogical phases the following: Quartz, Berlinite, Orthoclase, Feldspar, Anorthoclase and Calcite. By the other hand, joint with the big volume that present these residues and the chemical and mineralogical characteristics, these materials or sub - products can be used for production of ceramics, into mixes forming some materials for architecture (bricks, blocks, and tiles), refractory bricks, in the production of cement and to get some metallic values such as gold and silver involved in these residues.IntroductionActually the mining residues in Hidalgo State, Mexico are the result of more tan 500 years of mining, leading so a great volume of deposits, which we can classify in different types, among the most communes we have: Acid Mining Waters, Waters of solid transport and elements in the form of radicals, deposits of abandoned minerals without processing, and mining wastes of processed minerals known as burrows or dumps, being these the most abundant in the Hidalgo State [1-4].Form the metallurgical point of view, it is known that a characterization study if fundamental to find the viability of reuse of these kind of residues, leading so an additional use and the opportunity of get an alternative use into several industrial processes, due to its contents of oxides of silicon, iron, aluminum, calcium, sodium and potassium, principally, besides of its mineralogy and distribution of chemical elements into its primary and secondary phases [ 1-2, 5- 6]."

Jan 1, 2011

By J. B. Dilworth

OUTCROPS of coal have bees discovered is many localities is the Philippine archipelago, and practically all of the larger islands contain deposits of this mineral. Very little prospecting has been done to determine the value of the various coal-bearing areas, but so far as known, the largest and most promising fields are found : (1) is northern Cebu; (2) is the small island of Batan, a part of the province of Albay is southeasten Luzon; (3) is the somewhat larger island of Polillo, off the east coast of Luzon, and (4) is southern Mindoro, sear the small coast tows of Bulalacao. Northern Panay, south-central Cebu, and various localities is southern Luzon, Masbate, Negros, and Mindanao also afford evidences of the existence of coal-beds, the extent and value of which have not yet bees proved. The general position of these islands and districts is shows on the map of a portion of the Philippine Islands, Fig. 1. Some of these coal-fields have been known for many years (coal was discovered is Cebu 1827 and is Batas is 1842),1 and several futile attempts were made by the Spaniards to operate mines is these districts. But owing to many circumstances, chief among which were indifferent management, the political unrest of the islands, natural difficulties of transportation, and those inherent in the mining of steeply-inclined and somewhat irregular seams, no considerable output was ever obtained from any of these mines, and the fuel required is the many departments of industrial and political life has continued to be drawn largely from Australia and Japan. These conditions exist to a great degree at present, and though much interest is the coal-deposits of the Philippines

Jan 1, 1909

By F. M. Van Tuyl

The oil industry had its inception in the United States in 1859 when the first oil well was drilled by Col. Drake at Titusville, Pennsylvania. From, a production of 2000 barrels for that year there was a slow but steady increase, with some fluctuations, up to 1901 for which year the output was approximately 69,389,194 barrels. Since that time the production has increased with leaps and bounds due to the rapid rise of the automotive industry, the widening use of oil as a fuel under boilers and the development of the. Diesel engine. The production for 1921 is estimated to have been 469,639,000 barrels. During the same year more than 125 millions of barrels were imported from Mexico. The oil industry, including the production, transportation, refining and distribution of petroleum and its products, is now the third largest in the country. Present Condition of the Industry During and immediately after the war the demand for petroleum exceeded the domestic production plus the imports from Mexico with the result that our storage oil was heavily drawn upon. Prices for crude exceeded all previous levels in the history of the industry. Pennsylvania crude sold for $6.10 per barrel and Mid-Continent crude for $3.50. Such prices stimulated wildcatting greatly with the result that several important new oil pools were discovered. Then as production increased the depression came which caused a large falling off in consumption. Pennsylvania crude fell to $2.25 per barrel and Mid-Continent to $1.00. Large oil companies such as the Standard, Sinclair and Empire took advantage of the situation, erected additional storage tanks and bought up millions of barrels to hold until better prices returned. Prices have already improved owing to a better market, but the domestic production coupled with the Mexican importations is still in excess of the demand with the result that the surplus is being stored. At the close of the year 1921, the U. S. Geological Survey estimates that there were 183,890,000 barrels of crude in storage in this country, the largest stocks in the history of the industry, yet an amount sufficient to supply the country for only 119 days at the present rate of consumption. Price reductions are again anticipated in some quarters but in view of the probable falling off in the Mexican output in the near, future due to the rapid rate of exhaustion of several of the most important pools and in view of the expected increase in consumption of gasoline and kerosene during the spring and summer months it is more likely that the present price level will be maintained. Present Sources of Domestic Supply Seven major oil fields are recognized by the U. S. Geological Survey in the United States. These are the Appalachian, Lima-Indiana, Illinois, Mid-Continent, Gulf Coast, Rocky Mountain and California. Two of these, Mid-Continent and California, supply about seventy-five per cent of the present total domestic output

Jan 1, 1922

By F. Mielli

Over the last three years there has been an increase in mining congress and conferences focusing on water management. Water in mining is a key concern for mine managers and operations, and we are now seeing this operational dilemma escalated to the level it deserves. According to Frost & Sullivan research, mining water and wastewater treatment and its related technologies will be a U$3.6 Billion global market in 2016, which translates the importance of this issue. Looking at the current mining trends, some factors increased the importance of water in mining operations, including: ? Future mining investments will be located in geographical locations where water is scarce (water stressed areas) ? A decline in grade will increase the intensity of mineral processes and therefore increase the use of the water ? Increased sustainability and regulations will extend the control/monitoring of water during the entire mine life cycle representation of the mine water flow system. A water balance has several benefits/objectives in a mine operation: ? Mine planning/simulation of mining scenarios/climate change Production optimization ? Minimizing strategic and operational risks ? Social license to operate ? Water-smart mine planning ? Target: water neutral mines ? Benchmarking within and between sites ? Sharing knowledge/technology transfer ? Reporting/communications ? Permitting/Compliance

Feb 23, 2014

By A Jyoti, J R. Black, R R. Haese, E O. Ansah

Copper (Cu) is a critical metal in the transition to a low-carbon power supply. Presently, low-grade copper sulfide ores account for almost 80 per cent of the global reserves. Large amounts of water are required to process these low-grade copper ores. The mining industry utilises lixiviants from recycled water from different sources to conserve water, whilst enhancing Cu recovery. Some utilise intermediate to pregnant leach solutions, sea water, and processed water from electrowinning circuits with highly variable concentrations of ions. Previous studies have highlighted the formation of precipitates that passivate the surfaces of minerals in these low-grade copper ores and/or block flow paths for lixiviant during heap leaching. In this study, we utilised concepts of phase replacement to devise an innovative means of controlling precipitation and increasing copper recovery using industrial brine as opposed to freshwater. We propose the formation of Al-rich phases (such as AlSO4 + or alunite) to replace iron sulfate and iron hydroxysulfates (such as jarosite) during the chalcopyrite dissolution-precipitation mechanism. The rationale is to have available Fe3+ throughout the chalcopyrite leaching process. We tested this method by carrying out various batch experiments using CaCl2, AlCl3, and NaCl industrial brine types compared to freshwater and explored the capacity to leach Cu from chalcopyrite. There is higher Cu recovery during oxidative leaching of chalcopyrite in industrial brine with 91 per cent recovery using AlCl3-rich brine, 84 per cent with NaCl-rich brine, and 56 per cent with CaCl2-rich brine as compared to 35 per cent recovery using freshwater. In the absence of Al3+, various forms of iron sulfates, and jarosite are formed, reducing the availability of Fe3+ for chalcopyrite dissolution. The introduction of Al3+ leads to the formation of AlSO4 + species, thus lowering sulfate activity and the tendency for K-jarosite formation.

Aug 24, 2022

By Prasad Kummarapurugu, Maija Teijonsalo, Sirkka-Liisa Jamsa-Jounela

There has been a significant progress in the use of mathematical modeling and simulation in the minerals industry in the last decade. Process models have moved from academic world to important industrial tools. This paper reviews the status of mineral processing simulators and recent progress in simulator development and applications is discussed. The simulation for process design and optimisation is now an established technique, as evidenced by its increasing use of practising engineers through commercially available simulator software. The paper presents a systematic approach to the process study procedure for the control system development, clarified by practical case examples calculated by SimCon - a novel steady-state simulator for mineral processes. Examples of the application of SimCon in drawing flowsheets, calculating mass balances and making simulations for grinding and flotation processes are presented. At the end of the paper, the state-of-the-art and the future of computer-aided pro- cess study at mineral processing plants is discussed. Keywords: Simulators, modelling, object oriented programming, computer aided control system design

Jan 1, 1996