Search Documents

By R. E. Cook

This paper presents results of a study to determine to what extent errors in estimated free gas saturation affect the results of static pressure calculations from build-up curves in two-phase systems. Use is made of the method of pressure build-up curve analysis developed by Miller, Dyes and Hutchinson1 , with modifications for two-phase flow advanced by Perrine2. Cornhined fluid compressibility of gas-oil mixtures is included, with special attention given to the discontinuity that occurs in fluid compressibility at the saturation pressure and its effect on static pressure calculations from build-up curves. The sensitivity of static pressure calculations to errors in gas saturation is considered over wide ranges of formation and fluid properties and reservoir pressure conditions. It is concluded from this study that for analyses of two-phase pressure build-up curves (I) the use of under-saturated crude compressibility data, even when producing GOR's are at or near solution values, will result in very significant negative errors in calculated static pressrrre, and (2) except for large values of buildup curve .slope and/or very low crude gravities, rather large errors in calculated gas saturation can he tolerated without .significant effect on calculated static pressures. The conc1usions arc qualified as referring only to the effects of gas saturation and excludc possible errors in the nuumerous other factors that enter into the ancllysis of pressure build-up curves. INTRODUCTION As part of the analysis of basic data for several major Eocene reservoirs in the Bolivar Coastal field (Western Venezuela), it was necessary to analyze a large number of pressure build-up curves for oil permeability and static reservoir pressure. From performance data it became apparent that gravity segregation is very active in these reservoirs. As a result of this performance it was recognized that the free gas saturation within the oil leg of the reservoirs would be small but would be subject to certain errors in calculation due to the inaccuracy of relative permeability data in the low gas saturation region. Since all of the various methods of build-up curve analysis were originally derived for sin- gle-phase, constant compressibility systems, and since the presence of a small but rather indeterminate gas saturation would greatly affect the reservoir fluid compressibility, a study was undertaken to investigate the effect of gas saturation on the results of two-phase pressure build-up analyses. TWO-PHASE BUILD-UP CURVE ANALYSIS The method of analysis used in this investigation is basically that originally developed by Miller, Dyes and Hutchinson1, with modifications for two-phase flow advanced by Perrine2. Miller, et al, showed that the original equation for single-phase permeability away from the well bore, held for two-phase flow except that the calculated permeability is the effective permeability to oil away from the wellbore. This finding was acknowledged by Per-rine, who also presented the equation for effective gas permeability* as Since Eqs. 1 and 2 contain no terms influenced by fluid compressibility, no distinct problem should develop in calculating permeability from two-phase build-up curves. In regard to the calculation of static reservoir pressure from build-up curves in single-phase systems, the modified Miller, et al, method as presented by Perrine is briefly as follows. 1. From build-up curve data, PVT data for the reservoir fluid and the well spacing and sand thickness, calculate the climensionless shut-in time corresponding to the highest value of actual shut-in time (t, hrs) on the straight-line portion of a semi-log build-up curve. Dimenrsionless shut-in time is related to actual shut-in time by the relation, t- 0.000264 kt 2. From a graph of dimension less shut-in time vs dimensionless pressure difference (Fig. 1 1 ) find the value of dimensionless pressure difference corresponding to the value of 7 calculated under (1) above. Dimen-

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chryso-tile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings. Four of the more important factors that have influenced recent developments are: 1. The lack of discovering and developing new deposits of any important size to supply the increased demand. 2. Rapid postwar expansion of industrial uses, especially in asbestos cement products, together with in-rreased manufacturing facilities. Euro-peal) countries are again back on the market with their demand. 3. The ability of manufacturers to develop their technique of blending fibers and obtaining more utility value out of each ton of fiber, together with the utilization of shorter grades of fiber to obtain equally as good products. In the past, many manufacturers were wasteful in their use of fibers. 4. The struggle for reduced operating costs, in face of increased wages and prices of supplies, together with the necessity, at some mines, to change the method of mining from open quarry to underground. Most of the recent capital invested in the asbestos mining industry has gone into more efficient extraction of the fibers from the existing ore, especially in the recovery of the shorter grades. There has been very little new plant expansion. Progress in the utilization of shorter fibers has been so far reaching that some of the mining companies are retreating present tailings as they leave the mill, and others are considering retreating of the old tailing dumps for recovery of fibers that, until recently, were not saleable and were discarded as part of the tailing. Many of these dumps contain much valuable fiber from days when milling was very inefficient. It might be appropriate to mention here that the present known asbestos reserves of proved commercial value (excluding Russia) are being depleted at an alarmingly rapid rate, about 10,000,000 tons of ore is being mined annually. No new deposits have come into production during the last 15 years, with the exception of certain deposits in Africa, which are the most promising, and minor developments in Canada, Venezuela, Cyprus, Australia, and Brazil. The African deposits are the only ones that hold promise of developing large reserves. Unless new deposits are developed, in twenty years or maybe sooner, the supply picture will not be a very bright one. Stimulated by the acute shortage, increasing fiber prices and technical developments, many new areas are being prospected in Canada, United States, New Zealand, Newfoundland, South America, Europe, Africa, and China. From information now available, it appears that no real progress has been made in duplicating this rare development of nature by producing synthetic asbestos. The most promising experiments were carried out at the University of Leipzig, but they seem far from practical. There has been marked progress in fiber glass manufacture, but so far, it has replaced asbestos only in very few instances for minor uses. Asbestos ore and the fiber it yields are different in some respect at each mine and vary usually in the following: 1. Percentage of fiber content by weight to the gangue. 2. Variations in proportions of long and short fibers, some deposits being predominantly long fiber and others short fiber. 3. The hardness of the rock in which the fiber occurs. 4. The nature of the fiber, as to

Jan 1, 1950

By D. Zaharaki

The present experimental study underlines the advantages of factorial design in environmental, geotechnical and waste management experimentation. A typical case study regarding solidification of metallurgical wastes is presented and the main effects and interactions of three main factors are determined in order to establish the optimum experimental conditions in terms of compressive strength. Finally, a regression equation that predicts accurately the real compressive strength of a specimen under various experimental conditions is derived.

Jan 1, 2005

By Chidchai Loyprasert, R. A. Stoehr

"A computer model has been developed to predict grain structures in alloys solidified under unidirectional flow using a combination of three techniques -- solution of the equations for flow of an incompressible fluid bounded by curved surfaces by the SOLA-SURF algorithm, calculation of heat flow by a finite difference method, and simulation of grain formation by a two-dimensional cellular automaton (CA) model. The changing rigid surface has been taken into account. Heterogeneous and homogeneous nucleation are considered, and the growth kinetics of a dendrite tip are evaluated by the Kurz-Giovanola-Trivedi (KGT) model. These calculations were applied to solidification of an Al-4.5% Cu alloy flowing over a chill on the bottom of a channel, a system for which experimental results were available. Using a variety of flow rates and superheats, agreement between the computed and experimental results were very good including transitions between columnar and equiaxed grains, the aspect ratio of the grains, and the inclination of the grains to the flow.IntroductionModeling of casting and solidification processes has developed over the years along two distinct tracks: (1.) modeling of macroscopic heat transfer and fluid flow for design purposes, and (2.) modeling of microscopic processes such as nucleation and growth in order to improve the scientific understanding of the phenomena involved. The present work is an attempt to combine the macroscopic and microscopic approaches for the solidification of an alloy flowing over a chill. The specific case chosen is that of an aluminum-4.5 % copper alloy flowing linearly over a water-cooled copper chill for which experimental results were available over a range of flow rates and superheats. For the macroscopic calculations, the SOLA-SURF algorithm for solution of the twodimensional fluid flow equations was combined with the finite difference method (FDM) for calculating heat transfer. For the microscopic calculations, heterogeneous and homogeneous nucleation were considered, and the growth kinetics at the dendrite tips were evaluated. The cellular automaton (CA) technique was used to apply the microscopic kinetics to the temperature and .flow conditions."

Jan 1, 1999

By Leonard Obert

This report describes the development of a dynamic strain gage and a companion amplifier and recording camera -an apparatus designed to pick up and record the strain waves produced in rock by a nearby explosion. Also included in the report is a discussion of the relationships connecting the strain with the displacement, velocity, and acceleration for both plane and spherical waves. The proposed tests for which the strain gages were intended required making measurements in solid rock, a factor that necessitated the development of a gage that could be inserted and anchored in a small-diameter diamond-drill hole. The restriction on the diameter of the drill hole is required so that the presence of the hole in the medium will not influence the propagation of the strain wave. The gage should respond with fidelity to the frequencies present in a wave pulse generated by the nearby detonation of a small quantity of high-velocity explosive. Preliminary tests showed that this frequency range extends from 200 to 10,000 c.p.s. or greater. Also, the gage should be capable of measuring strains ranging from a few micro-inches per inch to several thousand micro-inches per inch. Other desirable design specifications included a low gage output impedance to permit the use of long cables, and a low gage cost, particularly in view of the fact that for the final design none of the gages can be recovered from the medium.

Jan 1, 1949

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electrochemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are modified in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.'-a In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative and may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole. These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in Pennsylvania, carried out by the Pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, in the published literature. The potential differences across the contacts of sandstone and shale are called in this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored Well In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored with diamond tools. The potentials were first measured with fresh water in the hole. A null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and crystals surrounding a pure copper elec-

Jan 1, 1944

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electrochemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are modified in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.'-a In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative and may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole. These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in Pennsylvania, carried out by the Pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, in the published literature. The potential differences across the contacts of sandstone and shale are called in this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored Well In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored with diamond tools. The potentials were first measured with fresh water in the hole. A null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and crystals surrounding a pure copper elec-

Jan 1, 1944

By H. T. Matson, G. Allan Wallis

In the Northern Rhodesia copper fields the size of the orebodies and the exceptionally consistent values over great distances made it possible to outline the ore with drill holes spaced at 1000-ft. intervals; in some cases, 2000-ft. intervals. Owing to the fact that the size of the deposits made it very evident that much outside capital would have to be called in to develop them and, owing to the wide spacing of the holes, it was essential that the sampling of drill holes be as accurate as possible, so that outside examining engineers could adopt the results as trustworthy within the limits of accuracy of the drilling method. With this object in view, the field staffs of the Selection Trust group of companies have studied for the past three years, and are still studying, drill sampling in a very thorough manner, and for this reason it is felt that these notes may be of interest to engineers or students who are, or in the future may be, in charge of drilling operations. The orebodies in this field lie in shales and sandstones, more or less indurated, in the lower strata of the Roan series, and the copper mineralization is in the form of sulfides predominantly, with some oxidized copper minerals. These interested in the geology and history of the area can find full details in a recent paper by Anton Gray and Russell J. Parker.' In some formations core recovery was good—between 90 and 100 per cent.—and where any difficulty occurred in recovering sludge, as in fissured ground, this was not insisted upon; but the samplers' difficulties, both practical and theoretical, do not commence until core recovery drops and sludge recovery becomes important, for if core is being ground up it is recoverable only as sludge, and naturally the sludge sample, which theoretically should contain only the material cut from the annular ring around the core, is being salted, in a sense, by the ground-up core. In the perfect core, where 100 per cent. core is recovered as well as 100 per cent. sludge, the two samples can be treated separately, as in the case

Jan 1, 1931

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By B. Singh

The use of wire ropes has already been tried in a few countries for roof support In mines. But the use of scrap wire ropes, as a method of support on extensive scale has not been reported from anywhere except India. Extensive trials using freshly discarded wire ropes for roof support were undertaken both in the laboratory and field. In laboratory, model beams supported with different reinforcing techniques were tested to evaluate their comparative load bearing capacity vis-a-vis reinforcing factor. Among all the tests, the model supported with wire rope system at 60° angle in combination with two supplementary vertical bolts offered the best result 1.e. about 95% reinforcement. It also accepted post fracture loading of the beam. In statical analysis too, the best result could be obtained with the rope installed across the gallery at 60° angle. All these findings are in conformity with the field observations obtained during roof stitching practices in coal mines. Of late, roof stitching, an effective and economical method of roof support developed at CMRS, India in 1972, found wide application in over 200 coal mines. In this method, a freshly discarded wire rope is grouted across a gallery in two inclined drill holes supplemented with two middle vertical roof bolts at every 1.0 to 1.2 m interval along the gallery. It is tensioned against the roof using wooden sleepers and thus, the whole system functions like a roof truss.

Jan 1, 1990

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents, and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1963 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1966

This paper reviews the developments in understanding of the entrainment mechanism and its modelling in industrial flotation processes over the last 30 years. Both valuable and gangue minerals in the pulp zone of an industrial flotation machine can be transported through the froth zone to the concentrate launder in the water which must also be transferred from the pulp zone to maintain a stable froth zone in conventional flotation. A size dependent portion of each entrained mineral continues in normal circumstances to the concentrate launder. The size dependency arises because the larger particles are able to drain more successfully from the froth region. Gangue minerals are recovered by a number of mechanisms, entrainment being an important one in many cases. The entrainment mechanism is discussed on the basis of the pattern observed in recovery û size data for minerals. Its industrial implications are discussed and means of minimisation of the importance of the mechanism are also discussed. Various means proposed for mathematical modelling of the entrainment mechanism are also described. The effect of process variables on key parameters in these models is reviewed. Properties of both the pulp and froth zones are discussed where needed and means of taking additional measurements with devices developed over the last ten years are discussed as part of the collection of more detailed data on the flotation process in general and the entrainment mechanism in particular.

Jan 1, 2005

By C. Carlson, W. Muir

The oxygen demand of the complex lead-zinc-iron feed at the Cyprus Anvil concentrator was determined dependent on the cyanide ion concentration of the pulp. By redistribution of the cyanide added to the grinding circuit in direct proportion to the amount of surface area created, a more activated flotation feed is obtained. Monitoring the oxygen demand of the flotation feed and grinding mill discharges has proved useful in diagnosing metallurgical problems in day-to-day operation.

Jan 1, 1976

By D. Harrington

Probably over 95 percent of the coal production of the United States depends upon the use of explosives before it can be placed in the railroad car at the mine, and up to the present time it has been impossible to obtain Pry kind of practicable explosive that isn't dangerous unless handled carefully. In other words, no "foolproof" explosives have been found to date and inspection of the accident records of the coal mines of this country indicates that the use of explosives in coal mines has taken a sad toll of lives. ACCIDENTS PROM EXPLOSIVES IN COAL MATES Of the 2,000 to 2,500 persons killed annually in the coal mines if the United States, 100 to 125 have been killed from explosives without an explosion of gas or dust; these accidents have been due to misfires, hangfires, premature blasts, or accidental setting off of explosives through carelessness or otherwise (but chiefly through carelessness in some form). In this type of accident the flame character of the explosive is not necessarily involved, although an unexpected or premature blast is initiated much more easily with black blasting powder, which has a long flame, than with a permissible explosive, which has a flame much shorter and of briefer duration. By far the greater number of such accidents are caused by black blasting powder or dynamite rather than by permissible explosive.

Jan 1, 1936

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By F. H. Edmunds

Introduction This paper, it is hoped, will serve as an introduction to further work upon the origin of the soils and to a more complete interpretation of the geology of Saskatchewan from a study of the soils of the Province. The great difficulty that is encountered in mapping the structure of the prairie regions of the west must be evident to all who have made the attempt. The rarity of good exposures, due to the extensive coverings of glacial drift, is the greatest obstacle, making it difficult to determine the exact stratigraphical position of such exposures as may be found. In many cases palæontological evidence is lacking, or, if available, our present knowledge of the stratigraphy is insufficient to justify division of the formations into horizons; and until many of these formations have been subjected to petrographic investigation, little can be done in using lithological differences as an aid to the correlation of the usually sparse outcrops met with in the Province. Topography may be of the utmost value as an indication of geological structure when considered in conjunction with other evidence. It does not necessarily follow that, because an area in Saskatchewan has resemblances in surface configuration to an area of oil-producing land in Texas, there is sufficient justification for sinking money in wells without further investigation. Such - investigation should include the study of available soil maps.

Jan 1, 1929

By Delvaux Carlos de Miranda Sobrinho, Hegler Zurick Arantes Assunção, Marco Venicio Mendonça de Souza, Luciano Toledo Ribeiro

This paper aims to present the development of a 600mm U-Pile that was done in Gerdau’s Ouro Branco Heavy Section Mill in order to feed the local market with a product.The focus of this study is to show the developmental process the Mill went through until it was prepared for hot trials. All roll pass and guide designs were developed by our own team. Analytical tools like Finite Element Analysis and reduced scale lead trials will be shown and how these tools impacted on the development timeframe and accuracy of the final results on steel.

Oct 1, 2019

By Thomas A. Simpson

THE Birmingham red iron ore district in Jefferson County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons. The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation's total annual production, and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country.

Jan 1, 1955

By J H. Heo, J H. Park, M J. Lee

In this paper, the challenging points regarding the high temperature physical chemistry of slags to achieve the improved and stable electric arc furnace (EAF) or electric smelting furnace (ESF) technology on the way to green steel will be reviewed, and the recent experimental and modelling research will be discussed. For example, the initial melting phenomena of hot briquetted iron (HBI) and the slag formation behaviour was observed using a high-frequency induction furnace. Main component of gangue oxides in HBI was SiO2, Al2O3, and CaO in conjunction with unreduced iron oxide. To increase the dephosphorisation efficiency, the distribution ratio of phosphorus between metal and slag was calculated using FactSage™ software, version 8.2 (CRCT ThermFact, Inc., Montreal, Canada) and was compared to the measured results. The optimisation of slag chemistry is required not only for maximum dephosphorisation efficiency with good slag foamability but also for minimum slag volume with less refractory corrosion in EAF process. The slag chemistry is also one of key parameters affecting the operation efficiency in ESF in view of FeO reduction behaviour, viscosity, sulfide capacity, etc.

Jun 19, 2024