Search Documents

By William E. Ford, Edward Salisbury Dana

Secondary Twinning. - When there is reason to believe that the twinning has been produced subsequently to the original formation of the crystal, or crystalline mass, as, for example, by pressure, it is said to be secondary. Thus the calcite grains of a crystalline limestone often show such secondary twinning lamella?. The same are occasionally observed (Ilc, 001) in pyroxene crystals. Further, the polysynthetic twinning of the triclinic feldspars is often secondary in origin. This subject is further discussed on a later page, where it is also explained that in certain cases twinning may be produced artificially in a crystal individual - e.g., in calcite (see Art. 282).

Jan 1, 1922

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

By Arthur B. Cummins, Henry Mulryan

DIATOMITE is a hydrous or opaline form of silica, commonly known as diatomaceous earth, diatomaceous silica or kieselguhr. The term "infusorial earth" has lost its original meaning and today is incorrect in view of the distinctions between diatoms and infusoria. Various locality and variety names are obsolete but some retain local significance. Moler and Celite are trade names that have become associated with diatomite products from certain deposits in Denmark and near Lompoc, California. COMPOSITION Diatomite is essentially silica with some combined water (2 to 10 pct). Frequently it contains organic matter (from traces up to over 30 pct) and varying amounts of inorganic impurities such as sand, cryptocrystalline silica, clay, volcanic ash, calcium carbonate, magnesia and soluble salts. In the natural or crude state, diatomite contains from 10 to 65 pct or more of free water. Table I gives analyses of several diatomites from deposits of different types. PROPERTIES Pure varieties, either massive or stratified, are friable and porous, of low apparent density, and somewhat chalklike in appearance. Varieties containing organic matter vary from sedimentary oozes to peatlike materials. Impure varieties may be more or less claylike, sandy, calcareous or cherty. Compacted types approach porcellanite and silicified shales. COLOR-white, cream, gray, tan, brown, greenish to nearly black. HARDNES-light-weight varieties appear 1 to 1.5 because of porosity, but microscopic particles are 4.5 to 6.5. SPECIFIC GRAVITY-1.9 to 2.35. APPARENT DENSITY---dry block form, 20 to 40 lb per cu ft; dry powder, 5 to 16 lb per cu ft. CRYSTAL SYSTEM-generally amorphous (isotropic by X-ray diffraction) but frequently showing faint cristobalite pattern.67.68,70 MELTING POINT-1400° to 1650°C. STREAK-white. LUSTER

Jan 1, 1949

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1937 and the reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Library, Student .Relations, Speakers for Local. Sections and Student Societies, and Mining and Metallurgy. To these reports members are referred for further details. Finances.-Income for the year was the largest since 1930, the figure being $189,394, an increase of $18,803 compared with income for 1936, exclusive of a special Rocky Mountain Fund appropriation of $2500 in that year for visits to western schools and Local Sections. Major items of increase were: $8,000 from current dues and arrears; $7,700 from advertising in MINING AND METALLURGY and the two periodical "Technologies"; and $4,800 from sales of TECHNICAL PUBLICATIONS (pamphlets) and TRANSACTIONS volumes for both current and former years. Initiation fees and clues from new members declined $2,300, principally because of the larger 'proportion of Junior Members to Members among the new enrollments. Junior Members pay no initiation fee and dues are $10 compared with $15 for Members.

Jan 1, 1938

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream's particle size and percent solids.

Jan 1, 1991

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,857 samples, representing the products of 103 companies. The samples were collected during June, July, and August 1955. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1956

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By Edward W. Mehal

This paper presents a review of the technologies which have been used in the application of III-V compound semiconductors to integrated circuits and arrays. These materials have properties which make them useful for various devices such as: light emitters, sensors, microwave sources, and microwave diodes. Technologies for incorporating these devices into integrated circuits have been reported and processes developed for fabricating planar devices using selective epitaxial deposition or selective diffusions. Isolation methods utilizing semi-insulating GaAs, oxide isolation, and ceramic insulation have also been reported. These techniques, and the devices and circuits produced or proposed are discussed. AFTER the invention of the silicon-integrated circuit, methods for utilizing compound semiconductors for integrated circuit applications were proposed. The scope of applications was potentially much broader because of the range of properties available from these materials. There also was the opportunity of coupling these properties with germanium and silicon devices to realize functions and circuits which could not be produced with silicon monolithic circuits. Table I exemplifies the range of electrical properties available in III-V compound semiconductor materials which are currently being widely used. A wide range of sensor and emitter applications result from the range of band gap. The band structure of GaAs and GaAsxP1-x permits their use as microwave oscillator source, and the high electron mobilities further facilitate their utility in microwave devices. The concept of "integrated functions"1 results from the availability of these materials and methods for utilizing their special properties. Heteroepitaxial growth allows the fabrication of a monolithic block of these materials. Semi-insulating GaAs permits the attainment of electrical isolation between components in a monolithic block without resorting to p-n junction biasing or oxide isolation methods. An "integrated function" is a unit which can perform a system or subsystem role and perform a number of electromagnetic functions. These functions could include sensor or input transducer, signal processing, interconnections, and control or output function. Two examples which demonstrate this concept are an optoelectric processor and a microwave receiver front end. The optoelectronic processor, Fig. 1(a), would consist of a light sensor, signal processor, and output emitter. The sensor could be InSb or InAs which would be IR-sensitive. The signal from this sensor would then be amplified and transmitted to the light emitter. The amplifier could utilize GaAs bipolar or field effect transistors. A Gap emitter would then produce visible radiation. The microwave receiver front end, Fig. l(b), would consist of a local oscillator section and a mixer section. A signal input from an antenna is mixed with the signal from the local oscillator. The local oscillator signal is produced by a Gunn oscillator. The single-ended mixer utilizes one Schottky barrier mixer diode. The IF signal would then be amplified further and suitably displayed. A further extension of the capability of utilizing the

Jan 1, 1969

Key elements of open-pit design fixing the ultimate pit limits are stripping ratio, pit slope angle, and grade cutoff. Results of exploratory and development drilling should be reduced to horizontal sections corresponding to level spacing. It is advisable to interpolate the actual drillhole values to a uniformly spaced 50-ft grid system. Vertical sections can be and are used to approximate the fixing of pit limits, but horizontal sections must be used to optimize a pit design. To develop a pit design requires the establishment of the break-even stripping ratio. This ratio is applied only at the surface of the final pit and must not be confused with the over-all ratio, which is always less; otherwise there would be no profit in the operation. The break-even stripping ratio is determined by the formula: [ ]

Jan 10, 1967

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,680 samples, representing the products of 130 companies. The samples were collected during December 1953 and January and February 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past ten years is given on page 5.

Jan 1, 1954

By H. L. Gilbert, C. Travis Anderson, W. J. Kroll

IN a previous paper,1 the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.2 When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8in. in diameter. The supply of direct current of high amperage for producing the . desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flexible tubing of the movable electrode, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decided to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 1900°C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica according to the reaction: Si02 + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1948

The carbonatite-hosted apatite deposit at the Cajati open pit mine in the Jacupiranga igneous-carbonatite complex is located in south-eastern Brazil. The major styles of apatite mineralisation include veins or veinlets, small pods or patches, disseminated apatite and locally massive aggregates. The metallurgical concentration of the apatite is accomplished by grinding the carbonatite, removal of magnetite with a magnetic drum, size classification with cyclones and flotation to suppress carbonates and collect apatite. To examine the character of the apatite grains and to apply those observations to apatite beneficiation, specimens of carbonatite were collected from recent exposures in the mine and from selected drill holes. This study utilised a variety of microscopy methods, including transmitted and reflected light, cathodoluminescence (CL) and scanning electron microscopy with wavelength-dispersive spectrometers for mineral compositions. It was found that LREE, Na and Sr are the main elements replacing Ca in the apatite, with relatively low oxide contents (<0.5 per cent, but up to about one per cent for Sr). LREE and Sr contents consistently increase in the latest intrusions (C4, C5 and SP24). Chemical and morphological modifications of apatite were recognised to be related to detrimental effects on flotation recovery. Three examples illustrate this relationship: 1.  Apatite with reddish CL is fractured. Locally that apatite exhibits no CL due to CL quenching caused by iron entering the apatite structure.2.  Apatite from the xenolith-rich area exhibits abundant fine, platy silicates that appear to interfere with flotation and lower apatite recovery.3.  So called æhardÆ apatite, which is more difficult to grind, occurs in an area in the mine that was affected by hydrothermal activity. That activity is evidenced by the development of a bright, white CL rim in the apatite, and by the presence of late veins of carbonates and sulfides that fill fractures and appear to contribute to higher cohesiveness of those apatite grains.

Jan 1, 2008

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by complex geometry of the open pit and the surrounding natural topography of an open-pit mine. The resulting inversion cap is known to contribute to the degradation of air quality in the open pit, resulting in loss of production. This paper discusses the development and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the analyzes effect of the geometry of the mine and the slope angle of the pit on the contaminants profiles in the mine.

Feb 27, 2013

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the Items is confidential. It present's analytical data for 4,608 samples, representing the products of 101 companies. The samples were collected during December 1956, January and February 1957. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the Notional Motor Gasoline Survey reports published during the post 10 years is given on page 5.

Jan 1, 1957

By E. J. Mayhew

Bentonite and newly discovered deposits of sepiolite, saponite, and hectorite are now being processed and marketed from the Amargosa Valley of Nevada. All of these deposits are large. The bentonite has been known for decades and is the whitest known. The only other sepiolite deposit is in Spain. The only other commercial hectorite deposit is at Hector, California. No other saponite deposit is known. All the components except bentonite are hydrous magnesium silicates. The bentonite is mixed layer Na-Ca. All the materials have characteristics unique to their locale and type, such as high yield point for drilling muds and liquid suspending agents. The sepiolite has geothermal stability. Figure 1.

Jan 1, 1979

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

Several factors contributing to the loss of fibre during treatment are a function of the paragenesis of the veins. The occurrence, of magnetite from the cap rock within the veins prevents complete fiberization. There is a marked similarity between these veins and those in the Koegas-Westerberg area of South Africa.INTRODUCTIONAn investigation of the mineralogy of the Wittenoom Gorge crocidolite veins was undertaken in the latter part of 1962 at the request of the Colonial Sugar Refining Co. Ltd. It was anticipated that such a study might reveal the cause or causes of the lack of recovery of some asbestos during beneficiation. Some interesting features of the mineralogy and paragenesis of the crocidolite veins become apparent, but it is emphasized that the investigation is far from complete, as the study did not extend to the field occurrence.The samples examined were selected from the mill and from the untreated ore.GEOLOGICAL SETTINGWittenoom Gorge is situated on the Fortescue River in the Hammersley Ranges of Western Australia and is one of several gorges in these ranges, on the sides of which 'crocidoIite asbestos is known to occur. The Hammersley, Ranges consist essentially of a series of quartzites, shales, ferruginous quartzites and dolomites. These' rocks are part of the Nullagine Formation (Proterozoic) and are usually either horizontal or gently folded. In some 'areas small beds of riebeckite as well as crocidolite are known to occur interbedded in the sequence.Riebeckite is a monoclinic amphibole, the formula of which may be stated as Na2Fe2"Fe2" (OH) 2Si8O22, and crocidolite is a fibrous variety of this mineral. This formula...

Jan 1, 1963

By Frank E. Cash

Large quantities of explosives are consumed in the underground mining of ores in the Lake Superior district. Because of the recognized danger of accidentally releasing the potential highly destructive forces contained, the safes possible procedure in the transportation, storage, and use of explosives is necessary. Underground magazines recently constructed in the district give evidence of the earnest desire of the mine operators to incorporate all possible safe-guards in the storage of explosives, including a careful choice of location and arrangement in the plan of the magazine.

Jan 1, 1946

By William L. Rice

This Bureau of Mines Open File Report on nickel is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign nickel properties and deposits has been abstracted for use in this report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 1984

By A. J. Lyon, J. B. Johnson, Samuel Daniels

The wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating at 932' F. (500" C.) for 2 hr., cooling in air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that" considerable improvement in the mechanical properties of copper-aluminum alloys may be obtained from suitable heat treatment applied to castings."' Jeffries and Gibson8 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932" F. in a nitrate bath for 1 hr., quenching in fish oil, and reheating at 300' F. for for 1 hr. Their results disclosed the facts that the ultimate strength and the percentage of elongation of sound alloys were usually, and quite uniformly, improved by heat treatment; that with the iron content ranging between 0.36 and 0.88 per cent. and the silicon content between 0.24 and 0.60 per cent. the effect of increasing the copper content (Tables 10

Jan 1, 1925