Search Documents

By A. W. Ambrose

"Introduction.Oil-field operations have often been carried on under great stress and haste, in which the prime purpose has been to put the wells down rapidly as possible, without regard to a few of the various factors affecting cost. In such fields as Burkurnett, Texas, where the well locations are town lots and other small tracts, the operator was concerned primarily with in drilling. In such cases a few thousand dollars more or less in the cost of a well not considered. We are reaching a time, however, when our reserves a,more definitely outlined and properties are being along more economic lines. Operators are becoming more concerned with the actual cost of this work, and are gradually learning that fuel consumption can be reduced in drilling and producing without delaying the speed of drilling, and in the case of production, it will greatly reduce the unit cost per barrel of production.Types of Field Boilers.In the oil fields there are in general two types of boilers; those which are used for drilling wells and are of a more or less portable character, and those established later in a more permanent form and serve for the purpose,of generating steam for producing the oil. As a rule, the latter type of boilers are larger than those of the drilling type. Usually, little care is given to the installation of drilling boilers; particularly in attempting to set them up in such a way as to avoid waste in of fuel. Because of the temporary nature of these installations there may be some justification for not giving them more,attention in this resend, but it is believed that a few precautions could be taken that would amply repay the cost and trouble taken. In connection with the boiler plants that are afterwards established, when a few producing wells have been,brought in with a life of two to ten years and probably longer, much care to the boiler-plant construction and to the installation of recording instruments which will assist in operating the plant at minimum cost."

Nov 1, 1920

'Nothing happens until something is sold' This statement is not original - it is a necessary orientation for marketing industrial minerals. The most important single philosophy of marketing is that it recognises the consumer as the starting point. Production orientation is concerned with producing products that the customer might buy. Market orientation is concerned with finding the needs of the customer and how they can be satisfied. The difference between the two approaches can be recognised in company structures but the most tangible difference is in the approach by a company to selling and development. In other words, it is the market that decides what can be done with a mineral. The markets requirements dictate what mineral, what grade and what price will be paid. Therefore it follows that when pricing a product we should avoid taking the basic cost and arriving at a final selling price through a series of standard markups (unless government insists on it). We should start with the price the market can stand and work backwards to find out whether you have a profitable product or one that will fail because it is too dear. Naturally a thorough understanding of production costs is necessary particularly when marginal markets are concerned.

Jan 1, 1978

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905

By B. Clermont

Ball mills are usually the largest consumers of energy within a mineral concentrator. Comminution is responsible for 50% of the total mineral processing cost. In today?s global markets, expanding mining groups are trying to optimize mill performances. Since comminution is concerned with liberating valuable minerals for recovery in the separation process, it is crucial to run the mills at the best operating conditions which lead to good liberation at competitive throughputs with minimum costs (energy and wear). The high availability of the equipment is also essential to maximize production and profit. To reach this key objective, continuous and reliable information about the mill operation is vital. An innovative tool which can deliver information about in-mill dynamics has been developed by Magotteaux. It can provide online and accurate measurements of the degree of grinding ball fill and pulp position for timely decision making and actions. This tool could be used on its own or linked to an automatic grinding ball loading system named Magoload. Therefore, ball load could be kept constant by using direct measurement. This article describes the Sensomag and presents some of the major improvements that can be achieved with it. Some other promising avenues are still to be explored. Keywords: Comminution, process control, process optimization, process instrumentation, online analysis.

Jan 1, 2010

By Henry Howe

THIS paper is a discussion of the extremely valuable one of Mathewson and Phillips, The Recrystallization of Cold-Worked Alpha Brass on Annealing,1 which not only gives us a wealth of important data reached with great intelligence, but also shows both uncommon powers of imagination and a perfectly fair spirit. Let me try to analyze some of their results, and to enunciate some of the laws to which these results point. For brevity I refer to them as "The Authors." The page numbers in parentheses refer to their paper. 1. The Visible Aspects of Recrystallization.-Plastic deformation in a single direction, as in cold-rolling, draws the grains out in that direction, that is, inequiaxes them, without destroying their apparent individuality. Each grain seems to endure the drawing out without changing either its volume or its orientation materially, for the etching tint of each grain seems to be as uniform after as before the drawing out, save for the "etch bands,"2 shown in Figs. A to D of the Authors' Plate I. As the drawn-out metal is heated progressively, on reaching a certain "disintegration temperature" these old grains seem to break up, probably into submicroscopic fragments, and this apparent disintegration is followed by a coalescence of these fragments, so that their number decreases and their size increases, till they may become very much coarser than before the drawing out. Ruder3 coarsened the grains of silicon steel in this way till single grains reached an area of 50 cm. (7.75 sq. in.). The deformation itself probably breaks each grain up into many very small fragments, but the fact that each grain continues to have a uniform etching tint different from that of its neighbors indicates that these fragments retain the initial common orientation of the grain. The apparent disintegration which we observe, then, is rather an abandonment of community of orientation for individuality of orientation, by the fragments formed earlier during the deformation. Hence we

Jan 10, 1916

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.' The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit in Yemen contains at least 9.4 Mt (10.4 million st) of ore at a grade of 10.7% zinc, 2.2% lead and 77 g/t (2.2 opst) silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to a conventional zinc smelter, and it has been necessary to formulate a less-conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material at Yanbu, Saudi Arabia. To give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulfide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, presents the flowsheet for Yanbu and estimates preliminary costs for both operations.

Jan 1, 2003

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler's performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of -43 per cent (LHV basis). This operating unit has also proven the use of the world's first FW/BENSONTM vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 x 1000 MWe solid fuel power block.

Jan 1, 2012

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler?s performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of ~43 per cent (LHV basis). This operating unit has also proven the use of the world?s first FW/BENSON? vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 × 1000 MWe solid fuel power block.

Jan 1, 2012

By P Lever, D Hainsworth, H Gurgenci

The ACARP Landmark initiative has created the opportunity to advance the level of automation in the coal industry by first focusing on the core production area of longwall mining. A Landmark Longwall Automation project was commenced in July 2001. The major outcome of automation using on-face observation has been divided into ten outcome areas that have been fully scoped for a three-year initial project life. A major facilitating technology has been the implementation inertial navigation system (INS) technology that can map the shearer position in 3D. A focus of the project is to deliver a system that is at least as productive as the current most productive manually controlled longwall face.

Jan 1, 2002

By Hugo Meggitt, Damian R. Siebert, Wystan Carswell

Excavation-induced ground movements are a critical component in the design and construction of deep excavations in urban settings due to the potential adverse effects on adjacent structures and infrastructure. Ground movements are influenced by soil stratigraphy, soil properties, adjacent structures, and construction means and methods. The use of empirical relationships, computer models, and reliance on experience with similar excavations in similar soil conditions often provides a basis for predicting excavation-induced ground movements. In this paper, data from 21 deep excavations approximately 20 ft to 75 ft deep supported by concrete diaphragm “slurry” walls in the Greater Boston area are compared to published literature, considering how different foundation systems (e.g. shallow foundations, caissons, and piles) of abutting structures have been affected by adjacent excavations. The influence of construction method (conventional vs. top-down) on adjacent foundation movements indicate that top-down construction typically results in smaller foundation movements. INTRODUCTION Estimation of ground movements due to excavation is a challenging endeavor, even with complex three- dimensional finite element modeling and high-order constitutive models that are increasingly available in modern engineering practice. Aside from the expense of the soil exploration and testing used to inform these higher-order models, the challenges of modeling past stress history, adjacent structures, and the groundwater conditions during excavation require not only large investments of time during design but also validation from past experience (to avoid a “garbage in, garbage out” paradigm). While site conditions such as soil stratigraphy, soil properties, groundwater conditions, and as-built conditions of adjacent structures can be obtained, measured, and estimated, the effects that means and methods of construction have on ground movements are difficult to quantify. During early phase design, assessments of predicted ground movement are unable to account for all aspects of project construction, nor is it cost-efficient to fully design an excavation while project parameters such as site size and excavation depth are under consideration by the design team. While construction is in progress, benchmarking support of excavation performance and associated ground movements in the context of successfully completed projects allows for a more nuanced view of system performance and provides the opportunity for more informed decision-making (if required) as construction proceeds. For these reasons, the use of empirical relationships and the collection of historical support of excavation performance holds high value for the practicing geotechnical engineer at all phases of the project.

Jan 1, 2019

By Leslie C. Richards

Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

Recent work on decoppering lead is reviewed CUS is formed rapidly even from dilute solutions of copper in lead. The mechanism of decoppering is discussed and an explanation for the retention of metals such as silver in lead is advanced. As decoppering tin appears to be an analogous process, the, Cu-Sn-S system is studied at 300°C.. CuS, which is not an equilibrium product, is found m decoppermg drosses. In the removal of nickel from lead, Ni3Pb2S2 is formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by stirring in sulphur. Decoppering bIsmuth IS thermodynamically favoured, but is complicated by the occurrence of CuBiS2 The Cu-Pb-S system IS the only one of the four studied where the equilibrium can be calculated simply, as the presence of ternary sulphIde or other phases invalidates calculations based on binary data.

Jan 1, 1971

This work presents: 1.) the results obtained from measurements of temperature profiles in pillars and at working faces of three coal mines located in Colorado and New Mexico, 2) a comparison of the experimental results with theoretical predictors based on linear heat flow models, and 3) temperature profile predictions based on a two dimensional coal mine model with an inclined crack located in the roof or wall of the opening. The thermal properties of the coal and shale samples taken from the mines were used as input data for the computer model. Good agreement was found between the measured profiles and the theoretical values obtained with the one dimensional model. The two dimensional model results show that a visible crack (0.01-0.07-ft thick) in a coal roof causes a surface temperature difference from 0.2 to 1°F at the edge of the crack for rock exposed to air from 1 hr to 288 hrs and with the air to rock temperature differences from 2°-6°F. A temperature difference of 0.3 °F was found between solid and broken rock in a shale roof with a 0.03-ft thick crack inclined 45° to the horizontal after a ventilating time of 48 hrs and the air to rock temperature difference of 2.1°F.

Jan 1, 1972

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

Your thoughts on the current status of the global minerals industries? The global economic, technological, social and political changes of the last two decades of the 20th century resulted in the emergence of a restructured minerals industry. This industry is now based on a new cost-cutting philosophy; utilization of modern technology; productivity gains rather than production tonnages; diversification of mineral markets; and globalization of exploration, mining and processing. Quantity and tons used to be the focus. The emphasis today is on remaining competitive in the marketplace by lowering per-unit production costs as much as possible. What factors and trends will impact the minerals industries in this, the 21st century? A number of parameters will impact minerals operations and shape the future sustainability and growth of the minerals industries. Increased demand for minerals will be accompanied by the demand for technical advancements. We will also see a continued emphasis on health and safety, environmental stewardship, and education and training. Let me elaborate.

Jan 1, 2002

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003

The criterion for assessing the accuracy of coal reserve estimates proposed by Philip and Watson (1982) is criticized.Following Royle (1977), it is suggested that the global estimation variance found by geostatistical methods is more appropriate.This method is applied to coal data from the Bowen Basin. This shows that two factors (the inherent variability of the variable under study and the total number of drill holes) have more influence over the accuracy of the reserve estimate than the form of the drilling pattern. Comparisons between the relative errors for different sized regions demonstrate that the spacing between drill holes is of secondary importance. The dominant factor is the total number of holes.Comparisons between the relative errors show that some variables such as sulphur need a much denser sampling than the others to obtain the same level of precision.

Jan 1, 1983

By S. C. Ells

Within the Dominion of Canada occurrences of petro-liferous shales have been known for many years. Nevertheless, with the exception of a comparatively brief period, Canada has had to depend largely on foreign sources for its supplies of crude petroleum and petroleum products. Attempts were made to retort local shales in 1859, near Collingwood, Ontario, and again in 1862, near Baltimore, New Brunswick. In each instance these attempts were abandoned owing to the rapidly increasing production of well petroleum from the newly discovered pools of western Ontario and Pennsylvania. Now, after a lapse of nearly sixty years, attention is again directed to the commercial value of Canadian shales as a possible source of crude petroleum. Province of Nova Scotia: The principal deposits of oil-shales occur in Pictou and Antigonish counties and have been known for more than 60 years. During the three years following its discovery, several thousand tons of a particularly rich sub-variety, known as stellarite (stellar coal or oil coal) was mined near Stellarton in Pictou county. It is stated that stellarite yielded upwards of 10,000 cubic feet of 36 candle gas, and that selected samples gave a yield equivalent to 170 Imperial gallons (204 U.S. gallons) of crude petroleum per ton. The average petroleum content of a cargo shipped to Boston was 48 Imperial gallons (57.6 U. S. gallons) and the associated shale or 'bat', gave a yield of 39 Imperial gallons (46.8 U.S. gallons). Part of the above output was shipped to retorting works in Boston and in Portland, and part was mixed with bituminous coals for the enrichment of illuminating gas. Following the discovery of well petroleum in Ontario and in the United States, the mining of stellarite ceased.

Jan 1, 1925

By D. J. Young

Alloys used at high temperature must resist both creep and corrosion. Design for corrosion resistance is based on the formation of a slow-growing, protective oxide scale by selective oxidation of an appropriate alloy component, usually chromium or aluminium. A successful scale will exclude other corrodents, notably carbon, which can otherwise cause extremely rapid corrosion at high temperatures. Selective oxidation of an alloy component necessarily lowers the concentration of that metal in the alloy subsurface region. Under thermal cycling conditions, mechanical damage to the scale leads to renewed oxide growth and accelerated alloy depletion. Eventually, a point is reached where diffusion of a corrodent into the alloy becomes competitive with the outward diffusion of alloy metal to repair the protective scale. Two examples of alloy failure by carbon attack are considered. In the steam cracking (pyrolysis) process, centrifugally cast tubes of heat-resisting alloy are exposed to a gas stream of hydrocarbon and steam, at a carbon activity of unity. Formation and repair of the surface chromia scale causes alloy depletion, Kirkendall void formation, and subsequent internal precipitation of chromium-rich carbides. Their formation makes chromia scale formation much more difficult, and generates internal stress. Eventually, the tubes fail by creep rupture. In other processes (e.g. steam reforming, heat treatment), synthesis gases are supersaturated with carbon at intermediate temperatures. Once the alloy's protective scale is breached, carbon attacks the depleted substrate. In the case of ferritic alloys, it forms a surface scale of Fe3C. As this scale thickens, the supersaturated carbon precipitates as graphite within its outer regions. The resulting volume expansion causes disintegration of the cementite in a process known as metal dusting. In the case of austenitic alloys, no metal carbide is formed. Instead, carbon dissolves in the depleted metal to diffuse inward and precipitate as graphite within the metal matrix. Again, volume expansion causes disintegration of the alloy, and metal dusting results. Dusting occurs at an extraordinarily rapid rate, and leads to failure by section loss or even penetration.

Jan 1, 2013