Search Documents

By Hornsey R., P. van der Merwe

The Two Rivers Project is a feasibility study to evaluate the UG2 chromitite layer on Dwarsrivier372KT, Mpumalanga Province, South Africa. The project, which commenced in August 2001, is expected to receive go-ahead early in 2003. The project sponsors (AVMIN 55%, Implats 45%)required project delivery within a short timeframe requiring optimization of the geological and geostatistical programme. Geological modelling was carried out in parallel to the drilling programme, and significant up-front geostatistical preparatory work was done. The time saving was approximately 4 – 6 months on project delivery. The cost saving to the project (excluding NPV considerations) is estimated at R20–30 million. Keywords; Two Rivers Platinum, Dwarsrivier 372KT, UG2 chromitite layer.

Jan 1, 2003

"Increasing demand for timely and accurate information about flotation plant performance requires metal accountants to increase the scope and reporting frequency of plant production. This trend has brought in-process inventory estimation at the forefront of metal accounting issues. Such significant in-process inventories can be locked in diverse process equipment (bins, holding tanks, flotation cells, thickeners, pipeline, etc.) or in stockpiles (ore, concentrates, tailings, etc.). Practice has shown that boldly ignoring these in-process inventories or the errors associated with their estimation lead to unreliable metal balances thereby creating confusion in plant production planning and operational performance assessment. To this extent, the characteristics (physical bounds, spatial heterogeneity and residence time) as well as the available measurements (volume, density, humidity, mass, composition, etc.) of each unit/section found in a generic flotation plant are jointly reviewed with respect to the particular metal accounting issues they present. The daily and monthly metal accounting tasks are then reviewed together with possible methods for obtaining reliable inventory estimates including different procedures for end-of month reconciliation.INTRODUCTION Most of the cost reduction initiatives of the mining industry aim at improving capital efficiency and asset utilization. Among the possible paths through which these goals can be achieved are mine-to-metal optimization, real-time plantwide process control (Hodouin, 2011) and knowledge sharing databases (Bascur & Linares, 2006). However, the successful implementation and subsequent monitoring will ineluctably results in an increased demand for timely and accurate information. This more than often requires metal accountants to increase the scope and reporting frequency of plant metal production. A striking example of such scope expansion is the Minas-Rio iron ore project in Brazil (Anglo American, 2013) having a pipeline route of 525 km between the concentrator and the concentrate shipping area. Several other mining companies have also set an increased frequency for their key performance indicators thereby shrinking the metal accounting period from monthly to weekly and daily. Those concurrent trends have brought in-process inventory estimation at the forefront of metal accounting issues. Indeed, as illustrated in Figure 1, improving trading reactivity requires improvements in production planning which strongly impacts the requirements for reliable metallurgical accounting. Furthermore, practice has shown that boldly ignoring significant in-process inventories or the errors associated with their estimation can lead to unreliable metal balances. In other words, since metal balances are the cornerstones of metal accounting, some of the risks associated with important business decisions are linked to errors associated with in-process inventory measurements."

Jan 1, 2014

By S. D. Dladla, S. Ramsamy

The majority of the tailings dam operations in South Africa will be required to comply with the new Global Industry Standard on Tailings Management (GISTM) within the next one to three years, depending on the dam classification and the requirements of the respective investors and insurers. With up to 72 auditable requirements, the implementation of the Standard needs careful planning and prioritization. This paper focuses on the practical steps to GISTM compliance for tailings facilities in operation in South Africa. The discussions are based on current practices, South African regulations, and industry standards requirements. The possible changes in dam classifications and the associated requirements are presented.

Jun 2, 2022

One of the important directions of further increase of quality and efficiency of control of mining companies and branches is the creation of the operation and development monitoring systems of such facilities. The main purpose of these systems is to provide managers with reliable and timely information on the current state and typical tendencies of operation of the facilities under control. However until the present time no scientific and methodical ground for system monitoring of the mining companies and branches has been created. Therefore, the authors of the report have aimed to assess the current situation with regard to the researches in this field and to do analysis of the most important aspects and ways of solution of the issue under consideration.

Dec 6, 2010

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By M. A. Roche

AST fall over half a million tons of ore and rock were broken in one blast at the open pit of the Hudson Bay Mining & Smelting Company's operation, at Flin Flon, Manitoba. The following particulars of the blast, and details of the preparatory work, indicate how an operation of this scope is carried out. The data given, in essentially the present form, were first published by The Canadian Mining Journal. The area blasted was 150 ft. wide and about 700 ft. long. A total of 123 tons of 50 per cent forcite gelatin, in 5 by 16-in. cartridges, was used for the charge. Drilling for the blast was started on May 29, and was completed late in August, requiring 1297 machine shifts for drilling only. Total footage drilled for the shot was over 5 miles of 6-in. hole. The main blast consisted of 232 holes spaced on 17.5-ft.

Jan 1, 1934

The development and distribution of gold placers in Otago û Southland is related primarily to the evolution and architecture of three distinctly different drainage networks that developed during and since Gondwana breakup: +        Late-Gondwana û Pre-marine; +        Middle Tertiary Post-marine; and +        Modern. Late Gondwana û Pre-marine drainage was dominantly recti-linear and controlled by normal faults and sedimentary basins formed before or during Gondwana breakup. Placers formed dominantly in 2nd order transverse drainages with primary sources in their catchments. This drainage network was progressively destroyed by inundation and burial by marine strata during Late Cretaceous û Middle Tertiary marine transgression that ultimately covered most of New Zealand. Middle Tertiary Post-marine drainage evolved on and incised the newly emergent low-relief landscape during regional marine regression driven by development of the present plate boundary through South Island. Most of Central Otago was drained into Southland and to the southern coast via a large braided river system with an extensive network of tributaries in its Central Otago reach. East Otago was drained by several smaller systems. Placers formed dominantly in proximal and medial reaches of 1st and 2nd order drainages with primary or pre-existing placers in their catchments. This drainage network was destroyed by inundation and burial of the Central Otago reach of the major system by lacustrine strata following tectonic damning of its middle reach by range uplift and development of a lake complex that covered >5000km2 of Central Otago. The Modern drainage network evolved from the Middle Tertiary network through complex response, firstly to uplift of NW-trending and NE-trending ranges throughout the region since the Late Miocene, and secondly to the effects of major Pleistocene glacial advances in West Otago. Placers formed in alluvial fans at range margins, proximal and medial pre-glacial fluvial systems and glacial outwash sequences. Evolution of each of these drainage networks has been accompanied by widespread sedimentary recycling of alluvial gold from older to younger placers, augmented locally by input of first-cycle gold derived from erosion of primary sources in the repeatedly exhumed basement rocks.

Jan 1, 2006

By James A. Madonna

Several universities and colleges in Australia, Canada and the United States, recognized the need to establish or reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this, a cooperative study with industry in one state or province from each country was initiated. These include Tasmania in Australia, British Columbia in Canada and Alaska in the United States. The objective of this work was to develop a diversified geoscience educational model at the two-year technical, vocational and continuing education level that provides the source from which any nation can draw the proper educational tools to create a new geoscience program, modernize an existing program or strengthen a weak program. More than 100 mineral industry organizations provided information regarding their specific training needs for support personnel. The data gathered have been used to identify training areas for semi-skilled, skilled and technical personnel in geochemical mineral exploration. These included geological, geochemical, environmental and computer skills. With the areas of major educational need defined for geochemical exploration, an educational field skills model was developed for the three levels of training. The international need for a study of this type was recognized as early as 1980, following numerous contacts from domestic and foreign geoscience educators regarding the structure and success of training within the University of Alaska Fairbanks Mining Extension program, located in Fairbanks. Contacts, correspondence and visits included educators from Australia, Brazil, Canada, Mozambique and the conterminous United States. The need was magnified between 1985 and 1989 at the University of Alaska Fairbanks, when an attempt failed at initiating and developing a two-year geoscience vocational-technology program leading to an Associate of Science degree.

Jan 1, 1994

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By S. Khoshkhooei

In this research, the effects of rare earth elements addition on thermal fatigue behaviors of AZ91 alloy were studied. Repeated heating and cooling cycles were applied on the samples at 170°C and 210 °C to develop thermal fatigue cracks, Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy (SEM) as well as energy dispersive X-ray spectroscopy (EDS), Thermal fatigue behaviors were improved successively by addition of up to 2-wt% RE, This improvement is attributed to consummation of the aluminum of the melt by precipitation of the needle shape Al 11 RE3 phases, This process reduces the volume of Mg17Al12 phases and consequently decreases the brittle Mg/Mg17Al12 interfaces which are the main reason of weak thermal properties of the alloy at rather high temperatures, Further additions of RE, however, reduced the thermal shock resistance of samples by increasing in the mean length of the brittle needle shape phases.

Jan 1, 2005

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

By Hermann A. Derbuch

Twin Mining made a conscious decision when it changed from gold mine explorer and developer to become a diamond explorer in Canada?s Arctic. It was a decision of survival in an environment that saw junior gold companies either disappear or turn into dot com companies. Twin Mining learned fast and staked within weeks of that decision the first 50 sq. km of claims on, what became, its TORNGAT property at 59½° latitude on the east coast of the Ungava Bay in northern Quebec. This land position, 724 diamonds later (including 322 macro diamonds of gem quality, white and transparent) grew to 507 sq. km today. The 74° latitude called when Twin Mining exercised the option to acquire 3 claims owned by Helix Resources Inc. which revealed exceptional diamond potential. A gem quality 5.4 mm (0.768 carat white and transparent) diamond and the discovery of 16 pipes on 15.2 ha convinced Twin Mining?s board to sanction the deal. Both properties have outstanding features. Kimberlite Dykes and Pipes are in outcrop. The property locations have deep-sea access near existing infrastructure. Their locations are in an environment that is stable and development friendly and has a positive track record with successfully operating mines near-by.

May 1, 2001

By A. Brown

RAPIDLY rising world demand for mineral products has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations. In recent years the Mines Branch of the Department of Mines and Technical Surveys in Canada has conducted such an investigation. This report of the work is primarily concerned with stress problems in some Canadian coal mines and, in particular, with mine bumps. Mines Branch investigations of this and related problems are carried out by a small team of mining engineers and physicists who, with assistance from geologists, pool their special skills in an integrated program. These Canadian investigations combine a field and laboratory approach. Since data obtained under contrasting mining conditions allow useful comparisons of ground behavior under stress, this article will present data gathered under a wide range of Canadian coal mining conditions. Two contrasting longwalls in eastern Canada will be discussed and two dissimilar pillar extraction operations in western Canada. Locale of Observations In eastern Canada observations are being made in the collieries at Springhill, Nova Scotia. The district's No. 2 mine, which has a history of bump occurrences dating back to 1917, is currently being worked at a depth of 4200 ft. The mining method is longwall retreating along the strike and the practice is to retreat three walls in line, each about 350 ft long. There is no machine cutting or shooting—the coal is hand-picked and hand-loaded onto face conveyors. There are three rows of hardwood chock block supports parallel to the coal face. These supports are built during the two daily coal loading shifts, and the rear line is withdrawn during the midnight shift. The goaves are partially packed by stone midwalls 12 ft wide which are built forward daily in step with the face advance. The seam dips at 15° and averages 9 ft of strong, well cleated bituminous coal enclosed in competent beds of shales, sandy shales, and sandstones of Carboniferous age. The bumps rarely disturb the retreating longwall faces but manifest themselves as violent upthrusts of pavement in the levels leading to the walls. Observations have also been made in Springhill's No. 6 mine, which operated in a 5-ft seam of coal at a depth of about 2500 ft. Although No. 6 mine was

Jan 1, 1959

Sampling errors result from heterogeneities within the lot under study. Within a rock mass in situ heterogeneity results in the geological nugget effect, which accounts for most of the natural variability. In broken rock, constitution and distribution heterogeneities are important. A major result of the constitution heterogeneity is the Fundamental Sampling Error (FSE) which is the smallest residual error that can be achieved. It cannot be eliminated, but can be minimised and refl ects the fact that the broken rock sampling process is never completely free of error. Together with other sampling errors, FSE contributes to the total nugget effect. The FSE for a sampling protocol can be evaluated using the so-called Gy equation. Its practical applications to low-grade gold ores have often been unsuccessful due to problems linking the FSE and minimum sampling mass and the defi nition of key parameters such as the liberation diameter. Well-designed sample protocols minimise the total sampling error and hence the nugget effect. Reduction of the nugget effect is a key requirement for all sampling programs whether related to exploration and resource evaluation, metallurgical test sampling, grade control or metallurgical plant sampling. This contribution reviews the relationship between heterogeneity, FSE and nugget effect in gold deposits; and emphasises the need for FSE management throughout the mine value chain.

Aug 1, 2010

By L. Garycki, P. Poks, R. Urbaniak, T. Gabka

In 2016 at Głogów Copper Smelter KGHM Polska Miedź S.A., after shutting down the shaft furnaces new FSF was launched. Currently, it is the only smelter with two direct to blister flash smelting furnaces in operation. The main difference between the vessels are the dimensions and production capacity. The new furnace design output is about 30% higher compared to the old flash smelting furnace working for 40 years. The paper presents a comparison of both FSFs operation, differences in technology and the way to optimize the process to maximize efficiency. INTRODUCTION KGHM Polska Miedź S.A. is the only company in Poland (eastern part of Europe) that extracts and processes copper ores. It is located in the south west of Poland and this region is called the "Copper Basin”. KGHM PM S.A. consists of three underground mines: Lubin, Polkowice-Sieroszowice, Rudna, concentrator plants, a tailings pond plant, three copper plants: Legnica, Głogów and Cedynia wire rod plant in Orsk. The publication relates to the operation of the furnaces in Głogów (the plant in Głogów consists of Głogów 1 and Głogów 2 which form integrated smelting and refining facilities). In 2016, after closure of the shaft furnaces technologies in the Głogów 1, a new FSF commenced operation. The simplified process flow sheets are given in Figure 1 and 2. Technological schemes are similar, but due to the differences in them, they will be discussed separately. Głogów 1 Enriched ores are discharged and directed to the feed preparation plant. Delivered concentrates are built up on the three bedding aisles in appropriate proportions. The concentrates are distributed in even layers in one of the three aisles. Aisle emptying is done with a blending machine which cuts across the concentrate layers and collects thus blended material, sending it via belt conveyors to a storage bin. From the cross- blending machine and conveyor assembly, the mixture of concentrates is directed to drying in the steam dryer. Part of the charge is directed to the FSF and part to the roaster for carbon elimination. Known in the world roasters are used to eliminate sulfur compounds or arsenic. In the case of KGHM deposits, the aim of the process is to reduce the energy value of the feed by eliminating carbon and converting sulfur from sulfide to sulfate. Changing the nature of exothermic to endothermic material is crucial in the case of furnace operation with design performance. Roaster is a separate furnace with an innovative character.

Jan 1, 2019

By Baafi EY

Open cut mining in Australia is facing the greatest challenge in its history in attempting to compete not only with other operations internationally, but also with underground operations domestically. Most flat dip and shallow depth surface-mineable coal reserves have been depleted during the last two decades and new open cut operations must extract deeper coal deposits. As open cut coal mines move into deeper areas and the stripping ratios increase, the relative cost of overburden removal also increases. It therefore becomes even more important to design the mine around the optimum overburden removal scheme. The deeper mines are usually multi-seam operations with a more complex geology and with more geotechnical and hydrological problems. Deeper mines are subjected to greater problems requiring more detailed mine planning and design, such as selection of the optimum mining method and pit layout. In planning and design of such operations, the number of alternative methods which need to be considered is consequently greater.Dragline productivity and its stripping capabilities are directly affected by the selection of digging method, strip layout and pit geometry. Every mine has a unique combination of geological conditions. The operating methods that work well at one mine may not necessarily work at another site. Selection of an optimal stripping method, strip layout and pit geometry for a given dragline must be considered with respect to the geological conditions of the mine. With increasing geological complexity of Australian strip mines, it is becoming more important to use sophisticated techniques such as computerised mine planning methods to assist in optimising dragline operations.

Jan 1, 1998

By E. Emami, J. Valencia, J. Sattarvand

The knowledge of the final location of a drillhole is critical in obtaining the expected blasting results. This paper proposes a new methodology to control the drilling accuracy in open-pit mines using aerial images and machine learning. Specifically, it investigates how support vector machines (SVM) and convolutional neural networks (CNN) are useful for automatically detecting blastholes over drone images captured in blasting patterns. Several datasets were obtained from different mines in Nevada (USA) and were used to train and test models. We then processed those images to create orthomosaic and digital elevation representations of the patterns. Thousands of patches were then extracted and augmented to develop SVM and CNN models. The results demonstrate that machine learning is useful for drillhole detection and, in this way, to control the drilling accuracy and use the explosive energy more efficiently.

Sep 1, 2021

By E. Varouchakis

Spartan Spatial Random Fields (SSRF?s) provide a new geostatistical framework (Hristopulos, 2003) with applications targeting environmental risk assessment and natural resources estimation. SSRF?s have the ability to incorporate constraints based on physical laws in the statistical description and have proved to be computationally fast in the analysis of synthetic data sets. This paper presents an application of a specific SSRF model and a new local-error spatial estimator (Hristopulos, 2005) in the mapping of environmental pollutants using a real data set. A detailed comparison of the local SSRF estimator with a classical kriging method is presented. It is shown that the SSRF approach provides a competitive alternative for spatial estimation.

Jan 1, 2005