Search Documents

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

OneSteel and BlueScope Steel have been working with the CSIRO to develop sustainable carbon fuels and reductants which are suitable for use in the iron and steel industry. One of the initial focuses of this work has been a process called steel recarburisation which is the addition of carbon to liquid steel to produce particular steel grades. This paper reports on the preliminary work and the recent full scale recarburisation plant trials conducted at the OneSteel Sydney Steel Mill.   Preliminary experimental work involved kilogram scale recarburisation of liquid steel with a range of commercial and prepared charcoal products. This work showed that charcoal dissolves into liquid steel very quickly and that carbon recovery to steel was inversely related to the charcoal volatile content. Initial larger scale work focused on the collection of wood, and preparation of low volatile charcoal which is required for steel recarburisation. Approximately three tonnes of charcoal was prepared at the Corrimal coke ovens of the Illawarra Coke Company. This charcoal was dried, crushed, sized and packaged in a form suitable for addition to 80 tonne liquid steel ladles.   The recarburisation trial was conducted over 30 ladle heats during June 2009. The charcoal was manually added to the liquid steel in 5 kg bags using normal plant practice. Conventional commercial recarburiser was also added to the liquid steel in alternate ladle heats. The performance of the charcoal was compared with the conventional recarburiser based on the carbon recovery to steel, hydrogen pick-up by steel and the rate of carbon dissolution into steel.   An analysis of the trial results showed that the charcoal performed at least as well as commercial recarburiser in carbon recovery and rate of dissolution but may have resulted in a slightly higher hydrogen content of steel. This is probably due to the higher moisture content of charcoal. The main challenges in the future include: increasing the charcoal density to improve transport and handling economics, securing a sustainable supply of biomass for the steel industry and developing a charcoal production industry so materials of suitable quality for both production and trials on other applications can be conducted.

Jun 1, 2010

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017

By Bruno Augusto Batista Ribeiro, Felipe Terra Elias, Wagner Moulin Silva

In the pyrometallurgical production of copper from its sulfides, converting in the Peirce Smith (P-S) Converter is still the most widespread method to obtain white metal and blister copper from the matte. Despite the fact of being a century-old process, it is still possible to achieve improvements in the process, by the use of modern tools, one of the most valuable being numerical calculation and computer-aided simulation. The present study presents three cases in which the angle for the gas injection and the number of working tuyeres are changed during the slag blow phase of the converting process. It was noticed that a decrease of the number of tuyeres, followed by an increase in the injection gas velocity, results in improved reaction volume and less stress to the refractory lining. However, an increase in the amount of copper lost to the slag as oxide is likely to occur.

Jan 1, 2014

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By Mario E. Rossi

Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations, to assess the uncertainty of minable reserves at the project?s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the ?correct? (or ?accurate?) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. The objective of this paper is to compare the ad-hoc ?uncertainty model? provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered and the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme. The application described in this paper is taken from a medium-sized Cu open and underground mine in northern Chile, and it demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more ?traditional? resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit.

May 1, 2001

The mining industry has been slow at adopting the latest management philosophies from other industry sectors, such as manufacturing, and in retrospect, with good cause. With the plethora of three-letter-acronyms such as TQM, JIT, TPM and now, BPR each touted as the panacea for profit improvement, you wonder if you must choose one or attempt to embrace them all! In truth, each new insight into organisational behaviour bears some investigation. This paper looks at the underlying principles and elements of successful change strategies, and how several mining companies, including coal mines, in Australia, Chile and Canada, are applying these principles to their operations. These examples illustrate the need to think radically, and to view mining as an overall process delivering value to the customer rather than a collection of functional silos. They also show that often, a continuous improvement initiative is not enough when a fundamental redesign, a paradigm shift, is needed for a performance breakthrough.

Jan 1, 1998

By Douglas A. Bartley, Davey Bickford, Raphael Trousselle

The long awaited arrival of a high accuracy detonator to reach the explosives end user will provide new opportunities the blasting community to become better equipped and able to improve upon the current approaches and methodologies used in blast design as they apply to the mitigation of adverse effects from blasting. This paper will detail the approach and findings throughout a several month research project to quantify the high accuracy detonator benefits and to mitigate a long standing vibration problem at a hard rock stone quarry in the state of New York. The tests conducted in this study were designed to provide important information as to the relationship between the use of high accuracy detonators and overall blast performance in terms of ground vibration prediction, control and improved rock fragmentation.

Jan 1, 1998

By L. P. Lamprecht

Traditionally, South African shaft sinking operations have used electric detonators for the initiation of blastholes. Globally, the trend in shaft sinking is to use the shock tube and detonating cord (STDC) initiation system, with value adding benefits. In pursuing this global trend, Cementation Mining of South Africa in partnership with SMX have ventured the STDC route. This paper explores the work carried out to date, and identifies a number of benefits to be gained by using the system.

Jan 1, 1999

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By Howard B. Hamilton

A switching system for high fault current 300 and 600 volt DC trolley and haulage systems, as used in the mining industry is presented. The system consists of paralleled main and auxiliary contactor circuits with a liquid metal current limiting device (CLD) in series with the auxiliary contact-or. Upon detection of a fault, the current is commutated into the CLD circuit. The liquid-metal vaporizes, increasing the CLD resistance and Considerably decreasing the actual current to be interrupted. This system will materially reduce the wear and tear on contactors because of the reduced interrupting requirement. the CLD is pressurized; when the current is interrupted, liquid metal flows back into the bore. Thus, it is resetting. Electrical and mechanical design principles are presented as well as materials for use, as found satisfactory in field tests on the device.

Jan 1, 1982

By Arnold O. Tanner

The domestic mining industry gained more strength in 1988 as the healthy comeback that became evident in 1987 continued and grew for many commodities. The increasing and more stable commodity prices, still predominantly in the metals sector, reinforced both the new ways of conducting business and the use of technological advancements in successfully lowering operating costs during the last 4 to 6 years. Some commodities and companies still struggled to survive, but increases in productivity and profits were becoming more common.

Jan 1, 1990

NASA has received direction for lunar habitation beginning in 2024. Prior to then, it will be necessary to learn about how lunar soil can be used to promote civilization on the moon. Questions must be answered: ?Will it support plant life?,? ?Can it be used as a construction material?,? ?What is needed to maximize health and safety?,? and ?Will it affect equipment, tools, machinery, and clothes?? The only samples available for study came from the Apollo Missions. Because the expense of bringing more material back to Earth is prohibitive, there is not enough available to perform studies to answer the above questions. Hence, there is a great need for its synthesis. Most efforts to date have concentrated on making ?simulant? from single natural resources of volcanic rock. However, another possibility is to use resources here on Earth to extract the minerals of interest into concentrates or so-called ?separates? using traditional mineral processing techniques, and then mix the separates in appropriate ratios to simulate the lunar soil. In this paper, results from a study in which dry Road Norite outcrop and wet mill tailings from the Stillwater Mining Company?s Concentrator located near Nye, MT were examined. Of course, the in-side challenge is to make ?separates? from gangue minerals.

Jan 1, 2012

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Kevin Green, Iván Contreras, Aaron Grosser, Jon Ausdemore, Rachel Leier, Amr Ragy

"Construction of a new tailings dam was required to increase tailings storage capacity at a trona mine near Green River, Wyoming. The new dam was founded on overburden soils underlain by both fractured and competent bedrock. The stored tailings and water had high salt content, resulting in salty seepage water. To reduce the impact of the salty water on groundwater and the Green River, the design of the new tailings dam included a 257,260 SF (23,900 m2) seepage cutoff extending into competent rock.An extensive subsurface characterization was performed prior to completing the design and suitable seepage cutoff methods were evaluated. The approach selected was a full replacement panel using hydromill and clamshell for construction and self-hardening slurry (SHS) for the wall material. Laboratory testing was performed and ongoing monitoring has continued to evaluate the hydraulic conductivity and seepage cutoff performance in the briny environment.The paper includes project background, the collaborative approach and outcomes of the QA/QC program, and the monitoring results for the seepage cutoff wall.PROJECT BACKGROUNDCiner Wyoming, LLC (formerly OCI Wyoming, LLC) owns and operates the Big Island Mine facility near Green River, Wyoming. This underground trona mine has produced soda ash since 1962. The Greater Green River Basin covers much of southwestern Wyoming and extends into northeastern Utah and northwestern Colorado. The Ciner facility is located in the Green River Basin, which is part of the Wyoming Basin physiographic province. The Green River runs to the west and the south of the Ciner facility.Beginning in the early 1990s, Ciner primarily disposed tailings underground in mined-out panels. However, in recent years, underground storage has become limited and some disposal has transitioned to the ground surface. Long-term planning revealed a need to expand Ciner’s surface tailings disposal capabilities. Pond 2, a previously permitted disposal area, was identified as the most viable location for a storage facility. The Pond 2 site is directly north of the Ciner plant facilities, northwest of the active Upper Delta tailings storage facility, and northeast of the Green River (Fig 1)."

Jan 1, 2016

Over the last ten years geological and mining software products have evolved greatly. Software companies developing such products have focussed almost exclusively on the development of technical aspects of the applications, addressing geological, ore reserve estimation and mine planning problems. These specialist applications, and the many other new technologies that are being developed by a myriad of niche developers, are an essential part of todayÆs hi-tech mining operations. Technology is also being used in many other areas to improve the mining process and there is no doubt that tremendous advances are being made in all these fields. Yet there is something missing. The manner in which the technologies are used and implemented has led to the creation of many independent and inefficient æislands of technologyÆ where a variety of products from different vendors are used to address different, but related problems. Problems occur with unreliable information, data duplication, data redundancy and transferring data between applications that may be incompatible or even run on different computer platforms. These problems impede the flow and availability of information and hamper day-to-day decision-making by mine management. A solution to this problem is to take a holistic view of all the various technical applications and incorporate them into a single information technology solution. This solution must encompass all of the information requirements of a mining operation and must provide facilities that address much of the modern thinking about mine management, including strategic mine planning, value management, key performance indicators, and maintenance of a mineral balance sheet. Gemcom is developing an Integrated Resource Asset Management System (IRAMS), which is an enterprise-wide integrated computer system that encompasses various applications typically found at a mining operation. The core component of the system is a common, open, industry standard database that can be shared by many users from each of the different departments at a mine. Around that central repository are the primary applications that provide the mine with information it needs to operate. Ensuring that the information is reliable, accurate, shareable, timely and consistent will eliminate many inefficiencies, and provide significant benefits to mining companies. In turn these benefits will lead to significant improvements in decision-making, productivity and profitability for the operation. The initial version of the IRAMS system is currently being implemented at the De Beers Venetia Mine in South Africa. The system is being built around a core repository using the Microsoft æBack OfficeÆ architecture, and incorporates key technical applications from Gemcom, Whittle, De Beers Technical Team, Wenco and JKTech. The benefits of enterprise-wide systems have long been recognised in the commercial arena and enterprise resource planning (ERP) systems such as SAP, JD Edwards and MIMS are becoming commonplace in the mining industry. The more forward looking software developers and mining companies realise the need for efficient management of the information gathered during the mining process and can see that the concepts used in ERP systems apply equally to the technical applications as they did to commercial applications. The use of IT in the mining industry has expanded tremendously over the last five years as enabling technology and management acceptance has become more prevalent, and there is considerable room for dramatic growth over the next five years. The evolution of geological and mining software has now reached the stage where mines will yield the greatest returns by integrating the applications used in each area of their operations.

Jan 1, 1999

By W. S. Dyer

The Minto coal basin lies in the central part of the province of New Brunswick, near the head of Grand Lake. The village of Minto which is the centre of mining activity of the district, lies about 35 miles east of Fredericton and somewhat greater distances to the north and west of the cities of St. John and Moncton respectively. Although coal has been mined in the basin for a number of years, it was not until recently that the production became sufficient to warrant a thorough geological investigation. The summer of 1922 was spent, in accordance with in structions from the Director of the Geological Survey, in making a detailed study of the geology and coal resources of the Minto coal basin, which is covered by the Minto and Chipman map sheets, each embracing an area of 200 square miles. The present paper is a short outline of the principal results obtained in the field. The writer wishes to acknowledge the assistance cheerfully given him by the managers and officials of the various companies operating in Minto. He wishes especially to thank Mr. W. B. Evans, Manager of the Rothwell Coal Company, for assistance in the collection of fossils and for the generous supply of information relative to the early history of the coal field.

Jan 1, 1924

By M. Hochenhofer

Keywords: desulfurization, mathematical model, slag reaction To produce ferroalloys like ferro-nickel for alloying purposes in a quality that meets the requirements of today?s steel industry, refining processes like desulfurization and dephosphorization are indispensable. The performance of desulfurization-treatment by slag reaction depends on various parameters, such as: sulfide capacity and viscosity of the slag, sulfur distribution between metal and slag, activity of sulfur in melt and movement of melt. Within this work, the combined influences of these parameters on the desulfurization of a ferro-nickel alloy were examined. As a basis for this examination, a mathematical model, based on data from plant trials, was created. This model demonstrates the relationship between desulfurization rate and initial values of the above mentioned parameters. With this model the relevant parameters were evaluated and assessed concerning their influence on desulfurization.

Jan 1, 2005