Search Documents

By F. Elgersma

A high purity electrolysis solution is essential for hydrometallurgical zinc winning processes. For this reason ferric iron containing compounds such as jarosite are precipitated as iron and impurity collector during the calcine leaching. Jarosite thus forms a chemical waste and creates environmental problems. This research contributes to the development of a wet jarosite treatment process, where less contaminated jarosite is produced which can act as an iron source. The present work studies jarosite precipitation kinetics and the uptake of zinc cations in batch and continuous experiments. The distribution coefficient for zinc in continuous experiments is constant for a wide ratio of zinc over ferric ions in the solution. Addition of NH, + ions in batch experiments accelerates the conversion rate equivalent to the driving force increment. Addition of 50,2-ions above the stoichiometric ratio increases the conversion rate less then could be expected from the increase in the estimated driving force. Zinc ions tend to retard the conversion rate. An increasing reaction temperature increases the conversion rate. Below 75 ?C the conversion rate approximates zero.

Jan 1, 1990

By Chas. F. Jackson

This paper is published as a progress report for the first half of 1929 on the study of wining methods and costs in the Eastern and Central States. Data obtained from 25 mines using open-stope methods are correlated and summarized. Some of these mines have been described in considerable detail in reports already published as Information Circulars. In addition to the published reports on individual mines, considerable data have been obtained from other mines which were visited and studied during the course of the investigation. Many of these mines will later be described in detail in separate papers, and when the field has been covered in this manner it is planned to issue a bulletin on open-stops methods of mining which will amplify the subject matter of the present paper. Definition of ?Open-Stops?. - The term "open-stopes" as employed by the Bureau of Mines is applied to all naturally supported stopes; that is, stopes in which the excavated ore is not replaced by support of an artificial nature other than preps or stulls and in which the ore or (and) capping are not caved during the active life of the stopes.

Jan 1, 1931

By A. A. Levinson, M. B. Kirkley, J. J. Gurney

"Scientific advances in the past decade have greatly clarified our understanding of certain concepts relating to the age and origin of diamonds. These advances are largely the result of geochemical studies of mineral inclusions in diamonds, made possible by modem analytical techniques which enable the accurate chemical analysis of micro-sized particles of the order of 200 microns in maximum dimension. As a generalization, the inclusions indicate that most diamonds formed from either of two rock types, peridotite and eclogite. Peridotitic diamonds have yielded ages of 3300 million years, whereas eclogitic diamonds areyounger and rangein agefrom approximately 1000to 1600million years. Kimberlite and lamproite, the two rock types usually associated with diamonds, typically are much younger than the diamonds they contain. Thus, it is now dear that kimberlites and lamproites are only the transporting mechanisms which brought diamonds to the surface and are in no way related to the formation of most diamonds. The latest concepts which developed during the past decade regarding the sources of carbon for the crystallization of diamonds from peridotite and eclogite, and the mechanisms of kimberlite and lamproite emplacement, IntroductionThe decade of the 1980s has seen major advances in our understanding of the age, origin and emplacement of diamonds. The information presented herein is applicable to virtually all natural diamonds, excluding diamonds related to meteorite impacts. There is still some question, however, as to the applicability of the new information to industrial grade ""fibrous"" or ""coated"" diamonds, and to microdiamonds (< 1 mm). In addition to drawing upon our own experiences, this review is summarized from a voluminous literature and for those interested in the original sources we recommend the books by Mitchell and Bergman (1991), Ross (1989), Nixon (1987), Mitchell (1986), Glover and Harris (1984) and Dawson (1980), and the review articles by Mitchell (1991), Gurney (1989) and Meyer (1985).are also discussed."

Jan 1, 1992

By Bradford F. Townsend, Marc R. Kritzer, Michael F. Roach, Dennis Ofiara

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2008

IN presenting a&apos;description of milling and treatment methods at the Waihi mine, it is advisable to first traverse a good deal of the past history of the mine, and show the various steps which have led up to present-day practice. The record of the company is one of steady, solid advancement, both in metallurgical and financial results. This is illustrated by the following figures, dating back from 1897...

Jan 1, 1912

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By Michael W. Russnak

Productivity and operating expenses are everything when it comes to judging how well your mine and company are doing. Stakeholders are always looking at these numbers and trying to understand if productivity is improving, if operating costs are trending downward and what you are basing your decisions on. o make improvements you first need to understand how you are performing. If you can?t get this basic information, you will never improve. You will not be able to make simple decisions related to maintenance, operations or production. Forget about planning, as you will only be guessing based on the numbers some stakeholder or your executive wants to see. The problem miners run into is not that the data doesn?t exist; it does, but typically it?s raw, it?s everywhere and its volume is huge. Today there is more on-board computing capability in shovels than we had on our desktops three years ago. Add other mobile equipment, plant systems and multiple OEM vendors to the equation and the challenge is daunting.

May 1, 2007

By William R. Barton

Sampling to determine development potential of beryllium deposits was conducted at 31 New England localities. A total of 54 additional areas where the geochemical environment appeared favorable were sampled to determine if economically interesting percentages of beryllia (BeO) might occur. Newry Hill-Plumbago Mountain, Maine, Iron Mountain, N.H., and Long Island, Maine, were investigated in some detail to determine the size and grade of deposits. The mineralized pegmatites at Newry Hill-Phunbago Mountain are extensive but very low grade; at Iron Mountain the ore bodies are very rich but of small volume; at Long Island beryl occurs with molybdenite, wolframite, and scheelite, but the tonnage of ore was not determined.

Jan 1, 1968

By O. M. Arafat, J. A. Finch

Since its development, the functional performance equation for ball milling (McIvor, 1988) has facilitated a new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the functional performance mill grinding rate at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining selection rate and breakage size distribution functions. The much simpler ball mill model has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this business-friendly ball mill model with optimization criteria from functional performance analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/ material provider and circuit designer.

Jan 11, 2017

By G. F. Cross

INTRODUCTION THE electrical system associated with the mining development of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, may be conveniently divided into three main parts, namely, the Island Falls power plant, the transmission line, and the distribution systems at the mine and metallurgical plants. For a description of the Island Falls power plant and the transmission line, the reader is referred to the paper, to be presented at this meeting, by R. W. Davis and M.F. Huffaker (1). The transmission line and sectionalizing combinations are shown diagrammatically in Figure 1. The present paper deals with the distribution systems at the Flin Flon mine and metallurgical plants. THE FLIN FLON DISTRIBUTION SYSTEM In the high-tension sub-station at Flin Flon, each incoming 110 kv. line is provided with manually operated, gang-type disconnecting switches. Each line is connected to Canadian General Electric type F.H.K. 39-60B-F.2 T.P.S.T. 110 kv. 400 amp. oil circuit breakers, each provided with M.K.4 centrifugal motor-operated closing mechanism. Gang-type disconnecting switches are installed on each side of incoming line breakers, and a complete ring bus system is formed through station tie breaker, which is&apos; further provided with gang-type disconnecting switches on either side. The?bus tie breaker is of Canadian Westinghouse design, type G.22B, 110 kv., 400-amp., solenoid-operated. All three breakers are provided with bushing-type current transformers, and the two line breakers are further equipped with bushing-type potential devices. Oxide film lightning arresters (121 kv.) are installed on each incoming line and are located outside the station. Each line is further provided with interlocked gang-operated ground disconnecting switches. All disconnecting switches are mechanically connected to auxiliary switches, which provide pilot service to indicating lamps in the remote-control room, located in a separate building.

Jan 1, 1935

By Frank M. Howell, Claude E. Schmidt

To counteract the spiralling costs of labor and materials against the fixed sale of its product, namely, gold at $35 per oz, Homestake Mining Co. has revised the milling flowsheet once and effected increases in the daily milling rate twice in the past 12 years. During this period the mining department has been able to hold production costs steady by increased productivity through technical improvements and utilization of the most modern mining by CLAUDE E. SCHMIDT and FRANK M. HOWELL, JR. 46-MINING ENGINEERING, APRIL 1963 equipment. The flowsheet alteration occurred during 1951-1953 when the two crushing plants at the shaft head frames were converted to a three-stage crushing system with the third stage closed circuited to produce a minus 5/8-in. product as rod mill feed.

Jan 4, 1963

By M. G. Hester

The inadequacy of traditional geostatistical methods for estimating some precious metals deposits has become apparent in the last few years. New methods or estimation such as Indicator, Probability and Multigaussian Kriging are difficult to understand and apply. Case studies using a new method of variogram calculation proposed by Srivastava show the method valuable for variogram estimation in precious metal deposits. Some simple, sometimes unorthodox. estimation methods that have proved useful in Some situations are presented.

Jan 1, 1990

By J Pan, G Qiu

In this paper, an analysis is made of the present situation in the Chinese steel industry and its demand for iron ores. It is shown that the demand for iron ores has been growing substantially with the rapid development of the steel industry all over the world, especially in China. However, the iron ore market is currently in the situation where supply exceeds demand due to the economic crisis, with more investment in mines and less output of steel for several years ahead all over the world. Gigantic pressure is confronting the Chinese steel mills due to the too high and irrational price of iron ores. It is time to return the price of iron ores to a normal position much closer to their value. More attention has therefore been paid to developing low-grade and complex iron ore resources in China due to the irrational price of imported iron ores. More innovative mineral processing processes have been developed to tackle these complex resources. A systematic introduction to the development of beneficiation processes for low-grade iron ores is provided, including upgrading low-grade siderite, limonite, micron sized haematite and magnetite resources.

Jan 1, 2009

By L. Alagha, L. A. Sanchez-Calderon

The existing methods for recycling lithium-ion batteries present initial hurdles related to the safe handling and preparation of the batteries to avert potential explosions. Submerging batteries in sodium chloride (NaCl) solution has become an acceptable industrial practice. However, the use of NaCl to discharge lithium-ion batteries rusts the batteries’ cases and releases metals which impacts the downstream processes that involve selective recovery of Li. This study aimed to determine the optimal concentrations and pH range of NaCl for the discharge of lithium-ion batteries for the purpose of minimizing the leach of Al, Co, Cu, Fe, Li, and Ni.

Feb 1, 2024

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

Since its creation in 1910, the Department of the Interior&apos;s Bureau of Mines has pioneered in the development of mineral technology, through research. From the very beginning, research on mine health and safety has been a dominating concern, and a responsibility that expanded markedly as a result of the Coal Mine Health and Safety Act of 1969. Until the mid-1970&apos;s research on fuel technology and coal production also was an important part of the Bureau&apos;s work. But in the four years following the 1973 oil crisis, Congress established a reorganized Federal energy research apparatus in which all fossil fuel research-encompassing extraction, use, and conservation-was centralized. Today, the Department of Energy houses Federal research on coal mine production technology, while research on coal and noncoal mine health and safety and environmental technology, and on noncoal mine production technology, remains in the Interior Department as a continuing responsibility of the Bureau of Mines. In carrying out its authorized research programs, the Bureau conducts both short- and long-term re-

Jan 1, 2012

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By Trevor R. Ellis

The extractive industries addition to the International Valuation Standards (IVS) is scheduled for publication in the next edition of the IVS book in January 2005. This will provide guidance for valuation of minerals and petroleum industry assets of all types for all appraisal uses. It will provide asset valuation support to the International Financial Reporting Standards for the stock markets of the world, and a global umbrella standard which can be supplemented for local needs by institutes and regulators. This paper discusses implementation of the IVS within the minerals industry and important issues that the industry should confront.

Jan 1, 2005

By Jacob Carr, Christopher C. Jobes, Chenming Zhou, LaTasha R. Swanson, Jennica Bellanca, Jingcheng Li

Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM— the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered.

By Huw Williams

"Power companies are always looking to increase the carrying capacity of existing transmission lines, and the preferred method is to string heavier capacity conductor lines. However this results in higher wind loading and the potential for towers overturning, if the existing foundations do not have the tensile capacity. On older lines, there is often a lack of information on construction type and dimensions and in practice the as-built foundation can differ considerably from design drawings, due to unforeseen ground conditions along the line route, and no record of the resulting change in design being made.Following successful trials in New Zealand, integrity testing with Frequency Response and impedance profiling techniques is now being used in the region to check concrete foundation properties in-situ and are enabling power companies to get the most out of their assets. INTRODUCTIONIn most regions of the globe, the US included, there is generally a requirement to upgrade transmission line capacities, to cope with increasing power consumption. Problems with under capacity only come to light for the public when blackouts occur, even in developed countries.A large number of transmission line towers are designed with a certain capacity redundancy and will be able to carry greater loads than originally designed for. Power companies are therefore looking for ways to assess their assets and to minimize the costs of upgrade work.Re-assessment of tower foundation capacities using design drawings may not be valid , as constructed foundations may differ considerably from design drawings, to accommodate local difficulties and in some instanced, particularly with earlier lines, there is no information whatsoever. This complicates efforts to determine the capacity of foundations considerably."

Jan 1, 2005