Search Documents

By A. W. Fahrenwald

FLOTATION practice in Idaho is now about 13 years old. The advance has been steady during these 13 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. ORES OF THE DISTRICT The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a-specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit, in Yemen, contains at least 9.4 Mt at a grade of 10.7% zinc, 2.2% lead and 77g/t silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to conventional smelter/refineries, and it has been necessary to formulate a less conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material, at Yanbu, in Saudi Arabia. In order to give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulphide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, the flowsheet for Yanbu and presents preliminary costs for both operations

Jan 1, 2002

By A S. Leitch

This paper is based on the accident prevention pro-gram carried out in the coal mines of Alberta. It defines the role of the Alberta Mines Branch and of The Work-men's Compensation Board, and relates how a safety pro-gram was initiated. The formation of the Alberta Class 1 Mining Safety Council is also described. The responsibilities of both management and the individual worker are then outlined, and the main features of a successful accident prevention program are delineated. T HE purpose of this paper is not to repeat generalities and platitudes about industrial safety, but rather to relate the experience of Alberta coal mines during the past number of years in their efforts to keep accidents to a minimum. It has been learned from experience that many basic principles are as sound today as they were 20 years ago. How-ever the complexities of modern mining methods and the modern man or miner have created problems that did not exist then.

Jan 1, 1964

By B. E. Thompson, H. B. Fuqua

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Coolie, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor Counties is due to the influence of what is known as the Cisco arch (so called because of its influence on Cisco deposition), the axis of which extends in a northwest-southeast direction across southwestern Wichita County into Archer County. Developments during 1938 Important discoveries in the district were considerably more numerous and of more economic importance than for several years. In addition to a number of small, relatively unimportant discoveries and to the usual local extensions to the various producing fields in the several counties, at least eight fields, most of them apparently of considerable areal extent and importance, were found. The Helmerich and Payne, Incorporated and Blackwell Oil and Gas Company No. 1 Wilson. 4 miles southeast of the town of Holliday, in north central Archer County, encountered a pay of Strawn age at a depth of 3841 to 3858 ft., and was completed for an initial production of 1952 bbl. T'his well opened a new deep pool in the K. M. A. producing zone 8 miles southeast of the K. M. A. production. Subsequently an additional deeper horizon, also of lowcr Strawn age, was discovered by wells that failed to yield commerecial oil from the horizon of the discovery well.

Jan 1, 1939

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Coolie, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor Counties is due to the influence of what is known as the Cisco arch (so called because of its influence on Cisco deposition), the axis of which extends in a northwest-southeast direction across southwestern Wichita County into Archer County. Developments during 1938 Important discoveries in the district were considerably more numerous and of more economic importance than for several years. In addition to a number of small, relatively unimportant discoveries and to the usual local extensions to the various producing fields in the several counties, at least eight fields, most of them apparently of considerable areal extent and importance, were found. The Helmerich and Payne, Incorporated and Blackwell Oil and Gas Company No. 1 Wilson. 4 miles southeast of the town of Holliday, in north central Archer County, encountered a pay of Strawn age at a depth of 3841 to 3858 ft., and was completed for an initial production of 1952 bbl. T'his well opened a new deep pool in the K. M. A. producing zone 8 miles southeast of the K. M. A. production. Subsequently an additional deeper horizon, also of lowcr Strawn age, was discovered by wells that failed to yield commerecial oil from the horizon of the discovery well.

Jan 1, 1939

By Reynold Q. Shotts

Underground mines, penetrating well below the water table, quickly fill with water when abandoned. Ordinarily, these natural cisterns are not thought of as sources of industrial water. Under special circumstance, if chemically treatable, they might become valuable industrial water reservoirs. An example of a group of about 20 mines in a geological and structural setting insuring water entrapment, rapid recharge and a possible minimum of contamination, are the small, compact Belle Ellen and Piper basins in Alabama's small but second most productive coalfield, the Cahaba. The mines have been abandoned from more than 50 to less than three years. The county now produces about a million tons of coal annually, all from strip mining. Figure 1 shows an idealized cross section of the strata in the Belle Ellen syncline near West Blocton, Bibb County, Alabama. Figure 2, 3 and 4 are maps showing the location of the syncline, other structural features, the outcrop lines of the three principal coalbeds underlying the basin, and the mined-out areas on the three beds (1).

Jan 1, 1973

By Luis Espinoza

La unidad minera Tintaya al igual que la Unidad Minera Antapaccay, son las operaciones de la división Perú de Xstrata Copper dedicados a la producción y comercialización de concentrado y cátodos de cobre. Sin embargo, la mina está en su última etapa de vida. En este sentido, surge el proyecto de integración de la unidad Antapaccay, donde se busca prolongar la vida útil de la mina y por consiguiente, el de la actividad económica minera en la provincia de Espinar. Por ello, el presente trabajo, describe los efectos de esta expansión de la explotación minera a través de la Unidad Minera Antapaccay que utiliza las instalaciones de Tintaya, manteniendo los planes de inversión social y el desarrollo económico local y regional.

Sep 21, 2013

By Michael Rieber

Commodity transportation by barge is possible on about 25,000 miles of navigable inland waterways in the contiguous 48 states. Barge operations are used chiefly for the movement of bulk raw materials ranging from farm products to iron ore, coal, and other bulky semi-finished as well as finished products such as steel, chemicals and petroleum [3,p.7-9]. The barge industry, unlike other transportation industries, is largely unregulated. This is because all liquid bulk commodities most dry bulk commodities transported by for-hire carriers and companies engaged in private transportation of their own commodities are exempted from Interstate Commerce Commission regulations. As a result, about 15 percent of the total ton-miles of barge traffic each year is under Interstate Commerce Commission regulation [13,p.14-25].

Jan 1, 1977

By I. Serepa, N. C. Steenkamp

Investigations were conducted to determine the condition and stability of the existing decline at amine in the Kalahari Manganese Field, Northern Cape Province, South Africa. During the inspection of the decline, voids were identified behind the concrete lining on the hangingwall and sidewalls over a total linear distance of 230 m. The voids did not provide confinement and, as a result, self-mining was occurring behind the lining. Water was flowing into the decline, over a total linear distance of 100 m, at areas where the decline intersected incompetent rock units, causing softening of the concrete lining and deterioration of the surrounding rock mass. Further damage to the concrete lining was caused by expansion and contraction of the wet red clay unit. Remedial work comprised void filling and water sealing to prevent further deterioration of the decline and ensure that it remained operable for the remainder of the life of mine. Void filling was accomplished by drilling rows of holes along the decline to access the voids and filling the voids with foam. This was followed by the sealing with polymer fluids. Telescopic pipes were also installed to allow water to drain off. A visual inspection was conducted and check-holes were drilled to assess the quality of the remedial work. The void filling material had penetrated cracks in the concrete lining, and areas where voids were intersected by check-holes were re-filled. Additional holes were drilled to re-seal areas that were still wet. The remedial work was completed successfully, as all voids were filled and stability achieved without compromising the concrete lining. The ingress of groundwater was also reduced to some residual dampness.

Mar 2, 2022

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By D. A. Sutch

En 1958 se instalaron dos hornos Tysland-Hole en la planta Siderúrgica de Chimbote, construído por Elektrokmisk A.S, cuya sede social se encuentra en Oslo, Noruega. En ese sentido, el presente texto describe el funcionamiento de dichas hornos para la reducción de minerales de fierro en Chimbote. Para el revestimiento del horno se emplean materiales aislantes diversos y tres tipos de mezclas refractarias que se colocan mediante apisonado. Asimismo, estas mezclas retractarias son apisonadas contra moldes metálicos que permanecen "insitu", es decir, que reciben la primera carga del horno.

Sep 1, 1963

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By Madan M. Singh

This report presents the results of an investigation of inclined roof bolts, anchored over pillars, in room-and-pillar coal mines susceptible to shear failures of the roof. Although the field data do not support this contention, it is believed on the basis of analyses and other work that inclined roof bolts do offer potential under some circumstances.

Jan 1, 1978

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

By M. Kashiwada

The zinc leach residues are introduced into waelz kiln to fume volatile metals and before the end of 1967, the waelz-fume containing zinc, lead, cadmium and indium was directly recycled back to the leaching process for the production of electrolytic slab zinc. However, since 1968, we have been recovering with success those valuable metals contained in the fume separately instead of direct leaching. According to the improved process, the waelz-fume, after being mixed with chloridizing agents, is fed into the rotary kiln to be roasted, wherein most of lead and cadmium content is collected as fume and most of zinc remains in the calcine. Zinc calcine thus obtained, containing 70 to 75 per cent zinc and, less than 1.0 per cent lead is sent to zinc plant for further recovery and the fume containing 40 to 50 per cent lead and 3 to 6 per cent cadmium is further processed to recover lead, cadmium and indium. The advantage of this process can be secured to the utmost when it is combined with the following subsequent treatments. (a) Blast furnace smelting of non-magnetic waelz slag to recover copper, silver and gold as matte. (b) Gallium recovering process from magnetic waelz slag. (c) Soda process of lead bearing cake produced after removing cadmium and indium from the said fume. Thus the extractions of zinc, lead and cadmium from leach residues account for 87 per cent, 72 per cent and 85 per cent respectively.

Jan 1, 1970

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1993. Most of the estimates are based on nine months data. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State mineral officer. In an effort to facilitate the rapid dissemination of information and publications produced by the U.S. Bureau of Mine, an electronic document dissemination system is now available for use. MINES FaxBack is a simple-to-operate automated fax response system that operates 24 hours a day, seven days a week. All a user needs is access to a fax machine with a touch-tone telephone. MINES FaxBack can be accessed by calling (412) 892-4088, using the touch-tone telephone attached to the user's fax machine. After calling MINES FaxBack, the requester is guided by a series of voice messages to assist in ordering the desired documents.

Jan 1, 1994

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Dorothy Walters

As an increase in the number of producers alters fact ors affecting supply, long-term prospects in traditional markets for many minerals weaken. At the same time, conflicts between national and international objectives undermine existing competitive elements in mineral markets and Canadian costs escalate. Such changes may dramatically alter the environment in which the mining industry operates.

Jan 1, 1979

By Rajesh Sonkar, Sanjeev Kumar

The deployment of Dragline machines in opencast coal projects involves huge capital expenditure as well as operating costs. The mine operators always endeavor to ensure smooth excavation of material by the Dragline machines while meeting the major objectives of safety, minimal disturbance to environment and optimal operating costs. Optimization of fragmentation through well designed blasts is fundamental in meeting part of the objectives is good fragmentation of rock or mineral proposed to be lifted by the Dragline machine. If the overburden lying over mineral is not properly fragmented, it may result in formation of ‘Toe’ the removal of which is the most arduous task in opencast coal mines. The mine operators always endeavor to achieve best possible results in blasting to ensure smooth operation of the high cost Dragline Machine. However, despite continuous efforts by the blasting engineers involved in bench blasting for the machine, the formation of ‘Toe’ is an ever nagging problem faced in large opencast coal projects eventually reducing the overall operational efficiency of mining.

Jan 1, 2011