Search Documents

By J. L. Bowlby

TWO years ago, at the annual meeting of this Society, the writer presented a paper dealing with various aspects of the water problems existing in the Cape Breton coal-mining area. Much of that paper was of a theoretical nature, in that an attempt was made to get at the fundamental principles underlying the problems, in order to establish a sort of background against which future results could be laid. Up to that time, only Central power plant in Glace Bay had been under observation, and, since the work had been in progress only a year, it was recognized that there were strong possibilities that certain variations in procedure might have to be introduced as w; became better acquainted with our problem. We were by no means certain that we had covered all the facts of the case. The present paper will therefore be of the nature of a progress report, rather than a formal contribution to the Society. Subjects of a theoretical or academic nature will be avoided as far as possible, attention being confined chiefly to the results obtained during the past two years. In looking over the work with low-pressure boilers, there are certain general conclusions that can apparently be safely drawn. Wherever possible, proper operating conditions will be expressed in terms of appropriate units. Absence of corrosion in boilers where the alkalinity has been maintained within the pH range 11.0 to 11.4 forces one to the conclusion that these are safe working limits. Previous experience had shown that corrosion would occur if the alkalinity were much reduced. Higher alkalinities are un-necessary, more expensive, and are said to introduce the possibility of pitting. We made no attempt to obtain quantitative data in respect to pitting. It is said to occur at pH 12.0. Consequently, conditions of alkalinity were main-tained well below this figure. In the above paragraph, the pH range 11.0 to 11.4 applies to boiler waters which have received the lime and soda treatment. The general practice, when this treatment is employed, is to use 1.0 lb. lime to 7.0 lb. washing soda. At Central power plant, soda-ash is at present substituted for washing soda, the equivalent proportions being kept the same. But not all the plants are on the lime and soda treatment. At Waterford Lake, a 1: 1 mixture of soda-ash and trisodium phosphate is satisfactorily employed, and in Sydney Mines and at No. 3 power plant in Sydney, good results are being obtained at a somewhat greater cost with a commercial phosphate treatment.

Jan 1, 1936

By Michael E. Ameel

The vibrated beam method of installing a vertical barrier wall is one of the least applied techniques, yet given certain site conditions and constraints, it is a cost-effective and proven method of controlling lateral groundwater flows. A recent full-scale application of this technique demonstrated its usefulness at an active manufacturing facility located in Northern Wisconsin. At this site, a 3,233 foot long cutoff wall was keyed into an underlying bedrock, which was located an average of 40 feet below the ground surface. Using a slag cement-clay based slurry, a 1E-7 cm/sec or less, nominal 4-inch wide cut-off wall was constructed using the vibrated beam method. Challenges included working around an active manufacturing facility with minimal access to the work area; installing the wall through a very dense glacial till; minimizing soil excavation volumes of potentially impacted soil; and, working around and adjacent to numerous active utility lines without impacting the facility operations. At utility locations, the vibrated beam wall was supplemented with a jet grout panel wall, without the need to bypass or otherwise interrupt any of the plant?s utilities. Quality control consisted of the monitoring and measuring of slurry parameters, survey control, and real-time monitoring and documentation of all critical barrier wall installation parameters. A vibration monitoring plan was also implemented to measure vibrations at utilities and adjacent facility structures. Proper equipment selection, significant up-front planning and close coordination with the facility resulted in a safe and successful project. The work was completed ahead of schedule during the 2009 construction season.

Jan 1, 2010

By C. S. Caldwell, L. C. Thompson

Mine closure and reclamation issues have evolved over the past several years becoming further complicated by stricter standards and by the cmrent economic climate and price of gold. Many mine permits are calling for more stringent remediation of spent ore heaps and tailings. Leachate solution water quality must meet strict discharge criteria for multiple parameters besides cyanide at mine closure. Closure standards are more difficult to meet and most mines do not have an increased budget at the end of mine life to deal with the falling standards. These issues make additional gold recove1y at the end of mine life a critical problem in financing some closure operations. Another issue is the length of time that must be budgeted for heap rinsing operations. Innovative biological processes developed and applied by Pintail Systems, Inc. at numerous mine closures have indicated that bio-processes can significantly enhance gold recovery dur­ing heap cyanide bio-detox over the recoveries expected from rinse operations. If heap rinsing can be eliminated or reduced and if gold recovery can be improved at the end of mine life, many mine closures may be possible with processes that pay for themselves or generate profit. Additional advantages of the bio­detox technology is that it can be engineered to treat multiple contaminants besides Weak Acid Dissociable (WAD) cyanide. Other contaminants treated in heap process solutions include nitrates, ammonia, heavy metals, thiocyanate and total cyanide. At the Cripple Creek and Victor Mining Company Ironclad Mine near Victor, CO, 5 million tons ofrinsed, heap leached spent ore were biologically detoxified to reduce cyanide content, enhance gold recovery during bio-detox and to reduce dissolved metals in heap leachate solutions. During the bio-detox treatment period a substantial improvement in gold recovery allowed the detox oper­ation to operate as a profit center. Final gold recovery was at least twice what was expected from a normal rinse operation.

Jan 1, 1998

Thirty mixed cultures of microorganisms from soil, water and mineral samples from the Groote Eylandt Mining Company mine site were approximately three times more effective in biodegrading manganese dioxide (34± 18 mg Mn++/1/day) than sixteen purified strains (11 ± 10 mg Mn++/1/day) isolated from the primary enrichment cultures. Two pure bacterial genera identified as a Pseudomonad and a Bacillus, with an excess MnOz and nutrient, were able to dissolve 106 mg Mn++/litre/day in mixed culture compared with 29 mg Mn++/litre/day when grown separately.

Jan 1, 1983

By E. H. Burroughs, M. J. Gavin

The references in the following compilation are selected chiefly from the literature of the years 1915-1920 , though a few of the more valuable standard works published before that period have necessarily been included . References to many articles have been omitted purposely , because the material covered by them is duplicated in publications included in the bibliography . It is manifestly impossible for the Bureau of Mines either to recommend or adversely criticize the statements of the various writers , particularly as to cost and profit estimates in articles referring to American shales , but it is hoped that the investigator will use caution in considering such statements , as it is well known that much of the literature on this subject has been published for promotion purposes and is therefore over- enthusiastic . Bearing this fact in mind , the reader should be able to judge for himself the reliability or usefulness of these articles .

Sep 1, 1921

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By A. Bumanis, K. S. Bawa

INTRODUCTION A rail rapid transit system called the "Metro" system is presently under construction in the Nation's Capital area. The agency responsible for the design and construction of the Metro system is the Washington Metropolitan Area Transit Authority, an independent tristate organization set up under an Act of Congress and financed by federal, state, and local public funds supplemented by revenue bonds. When completed, the Metro system will comprise nearly 100 route miles. About fifteen percent of this mileage is now under construction, while designs for the-remainder are in progress. The system is scheduled for completion in about eight years at a cost of approximately 3 billion dollars. The Metro system will involve nearly all types of construction generally used for rapid rail transit projects. About half of the mileage will be underground, comprising approximately 16 miles of rock tunnels, 10 miles of earth tunnels, and nearly 21 miles of cut-and-cover construction in earth (see Figure 1.). The remaining 51 miles of the system is planned to be constructed on the surface as at-grade or elevated structures. The system includes 86 passenger stations, 53 of which will be underground structures. Twelve of the underground stations will be large size chambers in rock while other underground stations will be constructed in earth as cut-and-cover structures. Thus, about one-fifth of the system will be designed as underground structures, namely tunnels and stations, in rock. Such designs in rock resulted from the existence of bedrock (schistose gneiss) at reasonable depths generally in the north and northwest

Jan 1, 1997

By H. Reginald Hardy

This report describes the results of a research project carried out to investigate the feasibility of using transducer arrays, located on surface or in shallow boreholes, above an active coal mine to detect and locate the source of underground microseismic activity which normally occurs during mining. The initial stage of the project involves the design and development of a self-contained mobile microseismic monitoring facility capable of use in remote field locations. Following this a variety of transducers, and transducer field installation techniques were investigated to obtain optimum sensitivity and high signal-to-noise characteristics. Preliminary efforts were also undertaken to develop semi-automated techniques for analysis of microseismic field data. Using the facilities and techniques developed field studies were carried out at a number of surface locations over a central Pennsylvania coal mine operating at depths of the order of 500 feet. In particular studies were con-ducted over a previously mined development area, troubled by extensive problems of roof instability, and over two longwall panels during mining. Although many of the field studies were carried out during the development stage of the project, results in general have been most encouraging. Limited results were obtained over the development area, however excellent microseismic signals, correlating with underground strata instability, were detected over both long-wall areas, proving the general feasibility of surface monitoring techniques. More recent studies, carried out as part of a subsequent project, and utilizing modified geophone installation techniques at a third longwall site, have verified explicitly the feasibility of measuring underground microseismic activity from surface locations. Sections of typical field data are included in this report along with a brief review of the studies carried out at each of the field sites. Detailed analysis of data obtained at the second and third longwall test sites will be presented in a later report.

Jan 1, 1974

By P. A. Hendricks

The surface coal mining industry in the United States employs over 50,000 people and is responsible for 60% of domestic coal production. This represents a very significant contribution to our national economy and an important source of highly skilled and well paying jobs. The U.S. Bureau of Mines (USBM) has targeted surface mining as an important research priority to reduce the social and economic costs associated with surface mining injuries and fatalities. USBM safety research focuses on the development of technologies that can enhance productivity and reduce mining costs through a reduction in the number and severity of mining accidents. This report summarizes a number of completed and ongoing research programs that address a broad range of surface mining safety problems. Research methods are described, and research products which are suitable for industry implementation are highlighted.

Jan 1, 1994

By G. Taylor

"The Iron Ore Company Of Canada's Carol Project is located in Labrador City, Newfoundland. Labrador City is some 912 air kilometers northeast of Montreal, and 417 ratl kilometers north of Sept-Iles, Quebec.Over 2,800 employees work at the Carol Project to produce some 20.0 million tonnes of concentrate and 10.5 million tonnes of pellets annually.In 1979 our Training Department started to develop the DACUM System of training for our Concentrator Operations Department.DACUM is an individualized, self-learning, training program. It is both a curriculum plan and an evaluation instrument.To date, the DACUM System has been completed for all occupations in the concentrator and work will commence shortly to develop DACUM for our Pellet Plant and Mine Operations Departments."

Jan 1, 1982

By Michael L. Clar

The U.S. Bureau of Mines contracted a study to determine the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. All relevant published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines was reviewed and organized into a bibliography. The impacts of mine water with respect to health and safety, production, environment, and costs were assessed. Sources of water inflow into underground mines were described. A summary description and evaluation of techniques that can be used to reduce the amount of water entering underground coal mines was prepared. A review of engineering practices currently used by operating coal mines in the Appalachian region to prevent the movement of ground and surface water into active coal workings was conducted. Major emphasis was placed on the identification of the geologic and hydrologic con¬dition of the site, onsite inspection of the methods used and an evaluation of their technical and cost effectiveness.

Jan 1, 1981

By M. Vallée, J. -P. Charette, D. P. Gold

"The Oka Carbonatite and Alkaline Complex is a Lower Cretaceous intrusive body of the Monteregian petrographic province. Carbonate rocks of various types, and associated alkaline rocks of the ijolite and okaite suites, are distributed in a double ring-dyke structure 4 Yi miles long by 1 1/2 miles across. Alnoite and alrioite breccia pipes intrude all rocks of the Complex and indicate, from inclusions, that a cover of Palaeozoic rocks existed at the time of emplacement.The results of radiometric, magnetic and gravity surveys of the Complex are compiled and discussed both with respect to the regional pattern and, locally, the bed-rock geology. The Complex is characterized by high-intensity anomalies.Exploration activities started during 1953, and mining operations began in 1961 on the property of St. Lawrence Columbium and Metals Corporation, at one time the world's largest producer of niobium concentrates. Because of the boudinaged and fractured nature of many of the rocks and the variability in grade of the ore minerals, the role of the mining geologist is both demanding and exacting. Rock types are varied and their mutual relation-ships ambiguous, the minerals are rare and complex, and close geological control of the ore is needed in the mine and in the mill. Closely spaced diamond drill holes are needed for mining control, and the ore-waste contact is defined mainly by assay results.In the exploration for 'carbonatites' in Eastern Canada, aeromagnetic surveys are judged to be the best exploration tool, followed in decreasing order by the search for circular structures on aerial photographs, regional gravity surveys and radiometric surveys."

Jan 1, 1967

By Foster Fraas

Under a very high vacuum of 10-8 torr the transfer of terrestrial mineral beneficiation methods to the vacuum ambient of extraterrestrial locations such as the lunar surface was investigated. In the size range for the electro-static and magnetic separation of ores (minus 35 plus 150 mesh) there is no adhesion of particles produced by crushing and grinding due to the limited contact area, and for repeated contacts area size has a frequency of occurrence in accordance to the normal law. The photoelectric effect which is successful in separating a few minerals in an air ambient has a wider application in a vacuum, while the lack of air viscosity and sound transmission provides for high feed velocities and the adaptation of particle vibration to dispersion and grinding. Contact electrification is reversible upon return to atmosphere.

Jan 1, 1970

By Kevin Baumgartner, Steven Babcock

A landfill in Phoenix, AZ reached capacity and was graded over in the 1970s. The property was subdivided into lots in 2007 to create a business park. However, the challenging site conditions caused by the underlaying landfill put into question the feasibility of typical deep foundation systems. Several different foundation systems were evaluated to support the proposed development. The considered systems were: drilled concrete shaft, driven piles, drilled micropiles and helical piles. Soil stability, landfill decomposition, method of installation, flexibility of design, anticipated material, and equipment costs were considered. A system of helical piles with concrete pile caps and grade beams was selected. To mitigate unknown obstructions, holes were drilled through the landfill debris at pile locations and then backfilled with screened granular material. The helical piles were installed through these backfilled holes and advanced to bear in competent native material below the landfill. This method allowed for minimal disturbance of the landfill materials and provided a strong and adaptable foundation. Additional advantages of helical piles on this site include minimal installation vibration, no grout or concrete in the deep foundation, and capacity verification for each pile via torque correlation. Two load tests were performed to verify the design.

Sep 8, 2021

By D. L. Sikarskie, B. Paul

A theory is presented for the static penetration of a single rigid wedge into brittle material. The material considered is one which exhibits both crushing and chipping phases in the penetration process. If the wedge angle and three parameters are specified, the theory predicts forces and associated penetrations during both the crushing and chipping phases. For certain ranges of the parameters agreement with the limited experimental data available is promising, except for the initial phase of the penetration process where refinements on the proposed theory are required. The theory also predicts that for certain values of the wedge angle and other known parameters, the chipping process does not occur and penetration is due entirely to crushing. When viewed in detail, the drilling of rock by percussive means involves, among other things, system dynamics, actuating forces, dynamic stress levels and the actual penetration mechanism of the bit into rock. If rock drills are to be significantly improved, a thorough understanding of the entire system would be highly desirable. In this paper, one aspect of the system, namely the mechanism of penetration of the bit, will be studied in detail. It has been found1 that for the velocities encountered in percussive drilling (of the order of 20 fps) a static analysis adequately describes the penetration process, at least for some rocks. Hence, we will only be concerned with describing analytically the static penetration of a single wedge shaped tool. It will further be assumed that the wedge is long enough to permit a two-dimensional analysis. Numerous authors have studied the static penetration of a wedge into rock. The following papers give some of this work and provide additional references to other work. Cheatham2,3 has assumed the rock to behave plastically and has obtained force-penetration equations for both Coulomb-Mohr and parabolic yield criteria. Evans and Murrell4 have studied the penetration of two types of coal and have found equations relating the penetration characteristic (P/dSc) to wedge angle for the various strength coals tested. race' attempted to find a correlation between hardness as determined by indenting the material and other mechanical properties and concluded that the results of such a test are generally inconclusive. His paper however contains a very extensive bibliography on the indenting of many different materials. Gnirk6 also has a fairly complete literature review on the static penetration of rock, of which he makes use in his indexing studies. A wide range of behavior is found in the wedge penetration of different rocks under different external conditions. For example, a rock that is essentially elastic-brittle at standard pressure may become elastic-plastic at a high confining pressure.7 It has also been observed4. " that some rocks will merely be crushed and indented by a wedge, whereas others will crack and form chips, furthermore the existence or non-existence of chips depends in great measure on the geometry of the indentor, type of rock and the depth of penetration. Hence, to attempt a theory which embraces all possible behavior is not practical at present. We, therefore, confine our attention to predicting the force-penetration characteristic and volume removal behavior for a type of rock which exhibits both crushing and chipping phases in the penetration process. Such behavior is characteristic of the harder rocks such as granites and represents a more difficult problem than the behavior of softer rocks such as coal and certain sandstones. In this preliminary study an attempt will be made to describe only the essential features of this complex penetration process. A qualitative description of these essential features is obtained with the aid of Fig. 1.1, where a wedge of vertex angle 28 is shown at some intermediate stage of the penetration process. As the wedge advances, the rock is fragmented (i.e. crushed) in some local region surrounding the wedge, the shape of this region being unknown. Simultaneous with the fragmentation in this local region, essentially elastic stresses are assumed to be building up in the surrounding rock. When a certain penetration level, di+1, is reached, the stresses along some surface are sufficient to cause failure and a chip is thus formed. The process now repeats, i.e., a crushing phase followed by the formation of a chip.

Jan 1, 1965

By Nelson P. Hulst

COMMITTEES. DULUTH.-Nelson P. Hulst, Chairman; J. B. Adams, W. C. Agnew, M. H. Alworth, C. W. Andrews, R. Angst, William R. Appleby, C. E. Bailey, G. G. Barnum, E. F. Bradt, Mylie Bunnell, George L. Cheesebrough, Peter Christen¬sen, F. A. Cokefair, T. F. Cole, C. A. Congdon, N. Cowling, George H. Crosby, M. D. Cullum, C. d'Autremont, Jr., H. L. Dresser, C. T. Fairbairn. Walter Fitch, F. L. Gilbert, J. T. Hale, G. G. Hartley, E. B. Hawkins, M. S. Hawkins, J. H. Hearding, Louis Hill, L. J. Hopkins, F. E. House, J. C. Hunter, 0. D. Kinney, J. W. Kreitter, E. J. Longyear, Alexander McDougal, W. A. McGonagle, A. M. Marshall, W. N. Merriam, T. D. Merrill, John Millan, P. Mitchell, Clarence Moore, Hon. Page Morris, C. H. Munger, Henry Nolte, W. J. Olcott, A. L. Ordean, Thomas Owens, F. A. Patrick, H. M. Peyton; D. M. Philbin, Capt. Charles Potter (U. S. A.), L. W. Powell, Harry Roberts, Louis Rouchleau, George A. St. Clair, J. U. Sebenius, Joseph Sellwood, Amos Shepherd, W. B. Silvey, George Spencer, George C. Stone, H. B. Sturtevant, George D. Swift, Kirby Thomas, C. D. Thompson, A. D. Thomson, G. A. Tomlinson, Charles Trezona, R. R. Trezona, Maj. J. H. Upham, Charles Van Barneveld, W. W. Walker, J. L. Washburn, A. C. Weirs, H. J. Wessinger, A. B. Wolvin, Dwight E. Woodbridge. HOUGHTON.-W. E. Parnall, Chairman; W. D. Calverley, Secretary; W. B. Anderson, L. S. Austin, Jacob Baer, William Bath, F. J. Bawden., Simon Beahan, John Been, C. H. Benedict, Walter Bloomfield, S. H. Brady, Samuel Brady, Henry Brett, A. L. Burgan, F. I. Cairns, W. H. Cake, Arthur L. Carnahan, William Carpenter, Phillip Carroll, John J. Case, T. L. Chadbourne, W. A. Childs, B. F. Chynoweth, Captain James Chynoweth, H. P. Clausen, F. G. Coggin, H. D. Conant, J. B. Cooper, J. R. Cooper, John Cuddihy, Thomas Cummings, Robert Davidson, J. B. Dee, J. R. Dee, T. S. Dee, Theodore Dengler, M. M. Dennis, Captain Thomas Dennis,. F. W. Denton, A. D. Edwards, R. M. Edwards, C. S. Fales, Daniel Fisher, Henry Fisher, James Fisher, A. L. Floeter, Frank H. Getchell, M. C. Getchell, W. M. Gibson, W. M. Gilliland, James G. Glanville, George Goodale, H. S. Goodell, A. R. Gray, Edward Grierson, Homer Guck, H. D. Haddock, Captain Josiah Hall, John L. Harris, Captain S. B. Har¬ris, Enos Harrold, F. William Hartmann, George L. Heath, C. M. Hoar, Thomas Hoatson, 0. P. Hood, Captain Thomas Hooper, Captain Joshua D. Husking, Dr. L. L. Hubbard, Arno Jaelinig, E. D. Johnson, G. A. Koenig, Edward Koepel, C. H. Krause, R. H. Leach, A. W. Leonard, James MacNaughton, Edward McCormick, Thomas McDonald, R. T. McKeever, F. W. McNair, James McRae, John Mackey, John C. Mann, Major G. A. Marr, Captain Thomas Maslin, Harry Mercer, James Merton, Michael Messner, William F. Miller, Captain J. Milligan, Dr. J. W. Moore, Charles H. Moss, H. F. Nickerson, Charles L. Noetzel, P. H. Paine, John Penrose, Captain John Pentecost, Graham Pope, R. C. Pryor, James Ramsay, J. T. Reeder, Allen F. Rees, J. H. Rice, W. G. Rice, James

Jan 1, 1905

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900