Search Documents

On the preceding pages, operations of the four major producers of nickel today have been described. There are, however, other operations in the world that, while not as large, are still of importance to the over-all picture of the industry. Among these are the Finnish producer, Outokumpu Oy, a state-controlled company that operates the Kotlahti mine 200 miles northeast of Helsinki. The ore from this operation, which began production in 1959, is pentlandite, chalcopyrite and pyrrhotite, occurring as disseminations in the host rock and in breccias. The flowsheet of the 1500-tpd mill at Kotlahti follows standard practices of crushing, grinding, and flotation to produce a pentlandite-pyrrhotite concentrate and a copper concentrate, both of which are shipped to the smelter at Harjavalta.

Jan 10, 1968

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

By H. R. Butler, R. N. Browne

"The International Nickel Company of Canada Limited consumes some 33 ½ millions of gallons of fresh water and reuses more than 100 millions of gallons of water daily. The continuing search for suitable recycle methodology has enabled the Company to put one 25,000 TPD mill on line utilizing recycled water entirely and a second 35,000 TPD mill is under construction which will likewise employ the concept of recycled water. Future milling plans are aimed at the replacement of all fresh water with recycled water, including sewage effluent and mine waste water.WATER REUSE AT INCO’s SUDBURY MILLSAs man searches unexplored horizons for new and economic industry, he must be constantly and acutely aware of the presence or absence of that precious commodity without which Industry, indeed Man himself, could not survive -- W A T E R. The water requirements of the world today are magnanimous, considering that in 1960 the estimated consumption in the United States was over 300 billion GPD (l) or more than 1,700 GPD per person(5) The magnitude of the problem can be visualized as one considers that three times this quantity of water will be required in the United States by the year 2000, when the dependable supplies of water are estimated to be only two-thirds of that required(2). How, then can we continue to wreak such havoc on that life-sustaining substance - WATER?"

Jan 1, 1970

By Benjamin H. Clark

"For over 50 years, Derrick Corporation has been renowned for its innovative and durable fine screening equipment and screen surface technology. Derrick’s latest innovation, the patented Stack Sizer, offers mineral processors both high tonnage capacity and high separation efficiency on an extremely small footprint.The Stack Sizer is suitable for separations from 6.3 mm down to 75 microns (200 mesh). The Stack Sizer, coupled with Derrick’s patented urethane screen surface technology, offers an extremely economical alternative to hydraulic classifiers, hydrocyclones, and less efficient low volume wet screening systems. Stack Sizers have been used in feed preparation for flotation, spirals, and a variety of jigs. Mineral processors wishing to reduce grinding circuit circulating loads and generation of slimes due to over grinding, thereby enhancing the efficiency of flotation and gravity circuits, now have another technology at their disposal to perform this critical sizing and grade control function.Over 200 Stack Sizers have been installed in numerous mineral processing applications worldwide attesting to the rapid acceptance of this technology. Stack Sizers are currently screening ferrous and non-ferrous metal ores, mineral sands, silica sand, kaolin clay, feldspar, garnet, phosphate, aluminum dross, potash, coal, tantalum, spodumene, niobium, and other rare earth mineral ores.INTRODUCTIONDerrick engineers have long understood and demonstrated the importance of screen width in coupling both high capacity and high separation efficiency for fine wet sizing applications. As opposed to fine dry sizing, where the length of the screening machine is critical for high separation efficiency, introducing slurry feed to screens in a thin and even layer at minimal velocities across wider screen surfaces allows for high capacities and efficiencies, with maximum screen cloth life. This is due primarily to the combination of free liquid and high frequency vibration of the Derrick motors, which allow fine undersize material to pass through the screen apertures. Lacking either of these factors would be extremely detrimental to the screening process. Without the high frequency vibration of the motor, the screen is essentially a low efficiency sieve bend. Without the free liquid to carry fines through the screen openings, the screen is for all intents and purposes a glorified conveyor or dewatering unit, as little or no sizing takes place once the screen is devoid of free liquid. For optimal screening results, Derrick recommends feeding slurry to a screen at approximately 20% solids by volume. Figure 1 shows the Stack Sizer design concept. Note that a single feed point is used to evenly distribute the flow to the five separate feed points."

Jan 1, 2007

By Verne E. Hooker

Near-surface temperature measurements in two granite quarries show that diurnal temperature variations are significant to a depth of 1 or 2 feet, and annual temperature variations are significant to a depth of at least 25 feet. As a result, ground stress anomalies due to temperature exist near the surface, and their magnitude depends upon the time of day and the time of year. Rock stress and corresponding temperature measurements were made in one granite quarry over a rock temperature range of 33° to 81° F. Measured rock temperatures show good agreement with values predicted from one-dimensional heat flow theory. Calculated and measured stress-temperature coefficients for the two granites in this study are given. Thermally induced stress variations in near-surface rocks tested were as large as 1,690 psi from combined daily and seasonal temperature changes.

Jan 1, 1971

By Pradeep K. Rohatgi, Clyde M. Adams

Structures produced upon solidification of the eu-tectic composition (33 wt pct Cu) aluminum copper alloy have been examined as a function of freezing rate dfs /d? , the rate of change of fraction solid (fs) with time (8). Slow (dfs/d? = 0.0016 sec-1), intermediate (dfs/d? = 0.02 sec-1) and rapid (dfs/d? = 0.4 to 7.30 sec-1) freezing rates were used. The lamellar Al-Cual2 eutectic is arranged in the form of rod-shaped colonies at rapid freezing rates. The colonies are aligned parallel to the direction of heat flow, whereas the lamellae within the colonies are aligned at various angles, as high as 90 deg, to the direction of heat flow. The colony spacing (C) is proportional to the square root of inverse freezihg rate. The relationship is C = 15.5(dfs/d?)-1/2 where C is in µ and 8 is in sec. The ratio of colony spacing to lamellar spacing is greater than 20.0 and increases with a decrease in the freezing rate. A duplex dendritic structure is produced at intermediate freezing rates. A fine lamellar eutectic is arranged within the dendrites (exhibiting side branches at an angle close to 60 deg from the main stem) and a coarse irregular eutectic appears in the interdendritic regions. The duplex eutectic structure is also produced at slow freezing rates. However, at slow freezing rates there is a Platelat of CuAl2, along the center of the main stem of each dendrite and the other lamellae are arranged perpendicular to the central platelet. THE eutectic between CuA12 and a! aluminum has been reported to freeze in a lamellar form by several workers.'-3 chadwick4 has measured the interlamel-lar spacing as a function of growth rate. Kraft and Albright2 have reported on irregularities in the lamellar structures, and have proposed growth models which account for the formation of faults during solidification. In certain instances the lamellar eutectic has been found to exist in colonies. The colony formation315 has been attributed to the breakdown of a planar liquid-solid interface due to rejection of impurities. The aim of the present work is to study the structures produced from the eutectic aluminum-copper alloy under relatively fast solidification rates, such as encountered in casting and welding operations. The solid-liquid interface presumably remains planar under conditions of slow unidirectional freezing which produce lamellae aligned parallel to the direction of heat flow. The local growth velocities are the same over the entire interface and are equal to the rate of growth of the all-solid region. The spacing between the eutectic lamellae is inversely proportional to the square root of the growth rate of the all-solid region. Under the freezing conditions used in the present study, the solid-liquid interface is cellular or dendritic and the local growth velocities are different in the different regions of the interface. The relationship between the growth rate of the all solid region and the local growth velocities varies with the location and the shape of the interface. The growth rate of the all-solid region is, therefore, an inadequate parameter to describe the eutectic micro-structures which depend upon the local growth velocities. For this reason the structures have been examined as a function of freezing rate, dfs/d?, where fs is the fraction solidified at time 0. The freezing rate was varied by a factor of 4000. The relationship between the freezing rate, dfs/d?, and the growth velocit of the all solid region depends upon the specimen geometry and the shape of the interface. EXPERIMENTAL PROCEDURES The A1-33 pct Cu alloy used throughout this study was made in an induction furnace, using electrolytic copper and aluminum of commercial purity (99.7 pct), the primary impurities being silicon (0.12 pct), iron (0.14 pct), and zinc (0.02 pct). Three ranges of freezing rates were investigated: 1) A spectrum of rapid freezing rates (ranging from 0.40 to 7.30 sec-1) was obtained in arc deposits made on 2-in. thick cast plates of the eutectic alloy. The arc was operated at constant power and was made to travel at constant velocity on the surface of the plate that was in contact with the chill surface during solidification. The pool of liquid metal formed under the moving tungsten arc solidified rapidly by heat extraction through the unmelted plate. Conditions of unidirectional heat flow were achieved near the fusion zone interface, especially in the center of the arc deposits. The great advantage of the arc technique is that rapid cooling and freezing rates can be varied in a qualitative way. The correlation between the arc parameters and the solidification rate is given by the following relationship:6-8

Jan 1, 1970

By Janne Kytökari

Controlling a wide range of minerals processes with single control system is an ordinary way to operate in mines all over the world these days. However the potential of these systems is not yet fully recognized nor utilized. The key issue is to manage the information in a way that enables automating the day-to-day tasks, quality control and safety functions. At the same time it provides means for optimization and constant improvement of processes creating a working environment where the system helps employees to do their key tasks instead of searching, modifying, and transmitting the huge number of information arising every day. The distribution of control system nodes enables the other processes to run heedless of a problem occurring in one of the sub-processes. Also the control room can be in remote location such as in large city removing the need to travel substantially long distances to plant sites every day. When all essential information is brought to the same place there is less risk for a mishap to happen due to information breaks that are often the cause of them. One of the biggest single reasons that result in production losses are break downs of machinery usually caused by normal wear, misuse, incorrect utilization rate etc. For this reason it is important to measure the condition of machines using vibration measurement and diagnostics. By moving from failure or time-based maintenance towards predictive or performance maintenance generates eventually a steady and predictable process but also results in significant long term savings. The mineral process at Talvivaara mine is based on bioheapleaching, whereby metals are leached from ore as a result of bacterial action. Bioleaching is a fairly new technology used in metals recovery. Therefore it is important for the mine to collect and analyze data from different stages of the minerals process. Talvivaara mine?s Metso DNA system has integrated machine condition monitoring and information management. These are not only necessary but also crucial in environmental conditions where the outside temperature can drop below -35°C, where ice and snow dominate the landscape and impact the equipment for four months a year and where distances between equipment can be up to 7.5 kilometers. Keywords: DCS, analyzer, machine condition monitoring, automation, remote communications, optimization, mining, metso DNA, Talvivaara

Sep 1, 2012

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019

By R. H. Eric, A. Chaendera

Gas jet was blown through bottom nozzles of a 1/5th scale CLU model in the presence and absence of slag. Kerosene and water were used to simulate the slag and metal phases respectively. Mixing time increased with increasing bath height and with a decrease in the gas flow rate. It was related to bath weight, bath height and gas flow rate. Slag increased mixing time by about 16% and the mass transfer values by about 32%. Mass transfer rates were higher near the bath surface and in the gas-liquid plume region. They increased with increasing gas flow rate and with a decrease in bath height. A relationship showing the dependence of derived mass transfer coef ficient on the gas injection rate was established. Turbulence characteristics inside the bath liquid were established to vary with location, vessel geometry and gas injection rate.

Mar 1, 2017

By AIME AIME

A COMMITTEE, representing a number of the larger oil companies in California, met in San Francisco on Nov. 12, 1919, for the purpose of discussing the depletion deductions to be allowed in computing the Federal income taxes under the Internal Revenue Act of 1918. It was the general sense of the committee that a system based on sound engineering principles should be formulated for estimating the value of oil properties, so that better and more uniform results might be obtained by the various companies in filing their returns with the' Bureau of Internal Revenue. A subcommittee, consisting of five petroleum engineers, was thereupon appointed to collect information and draft a report. The committee consisted of G. C. Gester, Carl H. Beal, J. H. G. Wolf, E. G. Gaylord, and E. D. Nolan; this report is the work of that subcommittee.

Jan 1, 1920

By R. A. Ixer, R. A. Lord, H. M. Prichard, A. J. Boyce, P. McConville, C. T. Pillinger, I. P. Wright, J. Maynard

Analysis of 62 samples show that the sulphides throughout the igneous stratigraphy have a magmatic signature, with the exception of the uppermost gabbros and the lowermost basal thrust talc-carbonate lithologies. Mean delta-34S values for whole-rock samples from harzburgites, dunite pods in harzburgite, crustal dunites and wehrlites, the main and high-level pyroxenites and gabbros suggest that the primary sulphides derived their sulphur from a magmatic source enriched in 34S. This finding is compatible with the proposed origin of the ophiolite above a subduction zone. Values for pyrite mineralisation in the uppermost part of the gabbros are thought to result from precipitation from a seawater-derived fluid, while isotopically light sulphur in the basal thrust could have been introduced from underlying metasediments. The replacement of pentlandite by heazlewoodite has not led to sulphur fractionation

Jun 19, 1905

By C. -T. Mutale, A. S. Tuling

Titanium can exist in three different oxidation states. Its oxides are numerous and in presence of iron and oxygen, iron-titanium oxide compounds can also form. Some of the oxides are non-stoichiometric, making the determination of the thermodynamic properties of titanium and its oxides in molten steel and in slag difficult. Therefore, for the assessment of titanium activity in molten steel using the electrochemical measurements of oxygen partial pressure, the identification of oxides in equilibrium with titanium is important. This paper reports on an investigation of solid titanium oxide inclusions, which have been identified by combining different methods of analysis on quenched samples. These samples were taken from a Fe-Ti-melt at 1600°C, quenched in cold water then mounted and polished for optical microscopy. The oxide inclusions were analysed using transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS). Both single crystal and polycrystalline diffraction patterns were used to identify the oxides by comparing the d spacings with those in the ICDD X-Ray Diffraction (XRD) database. XRD was used to analyse the oxide particles on the top of slow cooled samples. It was found in the TEM study that the similarity of the diffraction patterns of the various phases meant that unique identification was difficult to achieve in some of the diffraction patterns. However, TiO, Ti2O3, Ti3O5, Ti4O7were identified in quenched samples, while TiO2, FeO.TiO2and iron oxides were seen in slow cooled samples. It was also confirmed that the type of oxides is related to titanium content of the samples. Keywords: Titanium, Titanium Oxides, Iron, TEM, XRD, thermodynamic.

Jan 1, 2004

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

By Wilton Johnson

Native asphalt was produced by three companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm, R. L. White Co., Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Colorado and Utah, was mined by two firms, American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), and Ziegler Chemical and Mineral Corp. Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) closed its mining operation during the year.

Jan 1, 1988

By A. L. Paverd

The petrology of a number of pyrometasomatic mineral deposits in north Queensland, Australia, were studied to evaluate the use of mineralogy and major element chemistry in the exploration for copper, lead and zinc-bearing skarns. Results indicate a direct correlation between the character of the mineralization and the composition and nature of the host rock. The study of garnet compositions proved the most useful. Economic mineralization was limited to limestone-derived skarns containing garnet of And60-90, whereas skarns containing garnet of less than contained less than 1And55 contained less than 1% total sulfide. Skarns containing garnet of And60-8S host the best mineralization; above And8S' copper, lead and zinc sulfides decrease and magnetite and pyrrhotite become the dominant ore minerals. Similar correlations were found for pyroxene, amphibole and 'the bulk composition of the skarns.

Jan 1, 1981

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine's planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991

By Ogden Tweto

The Leadville district, on the west flank of the Mosquito Range in central Colorado, has produced silver, zinc, lead, gold, and minor metals valued at $512,000,000. The ore deposits are in a sequence of dolomites and quartzites, Cambrian through Mississippian in age and about 500 feet thick, which is extensively intruded by porphyry sills, dikes, and plugs of Tertiary age. The sedimentary rocks and sills dip about 15°E and are broken by many faults, which are predominantly of nearnorth trend and downthrown to the west. The ore deposits are principally blanket or manto replacement deposits, but in the eastern part of the district many veins occur also. The replacement deposits are largely confined to three dolomite units in the stratigraphic sequence. Of these, the uppermost or Leadville Dolomite is the most productive. Most ore bodies are on the underside of porphyry sills and, particularly, beneath sills that occupy unconformities. Many replacement bodies have vein roots or branch from veins. The veins occupy faults and are productive mainly in the section of quartzites and dolomites and included sills. The primary ores consist principally of pyrite, marmatitic sphalerite, and galena but locally contain chalcopyrite, silver minerals, bismuth minerals, and gold. Principal gangue minerals are manganosiderite and jasperoid. The ore deposits have a crude zonal pattern centered around an intrusive center at Breece Hill, which evidently influenced ore deposition thermally. The ore deposits were oxidized to depths of several hundred feet in Miocene time. Bonanza ores mined in the early days were characterized by cerussite, cerargyrite, and embolite. Later, zinc carbonate ores were identified and mined on a large scale. The Leadville district is a complexly faulted and intruded area at the intersection of major fault systems trending N20°W and N15°E in the Mosquito Range. The intensely fractured area evidently localized igneous intrusion and subsequent mineralization. Ore solutions rose on many of the faults in the area, presumably from the same source as the porphyry magmas. Movement on these faults continued into the Pleistocene, displacing ore bodies, oxidation zones, Pliocene sediments, and glacial deposits.

Jan 1, 1968

By Mark Van Dyke, Ted Klemetti, Jake Beale, Zoheir Khademian, Joe Wickline

In 2016, a 3.7-ML magnitude event caused by mining activity occurred at a longwall mine in southwestern Virginia which was recorded by the United States Geological Survey (USGS) and felt by local residents. The event was the largest of its kind since a global mine design change by the operator was instituted in 2008 following three large events in 2005, 2006, and 2007 (3.4, 4.3, and 3.4 Moment Magnitude (Mw), respectively). Two of the three pre-2008 events (2005 and 2007) damaged ventilation controls in the mine which fueled a mine fire. In 2016, the mine’s management requested researchers from the National Institute for Occupational Safety and Health (NIOSH) to access geological data and determine what parameters could possibly lead to events of a magnitude of 1.0 ML or greater. Evaluation of 2152 geological data points and modeling revealed three major geological factors in common with the majority of the 181 recorded +1.0 ML events from 2009 through 2016. Three levels of seismic potential were identified as follows:

Aug 4, 2023

By L. K. Daneshmend

The mine of the year 2020 will need to be based on a new way of mining. It will employ technology in a paradigm that assumes responsibility for sustainable development: taking account not only economic but also ecological and social issues. This will require a holistic approach to mine design and planning, considering all controlling factors and impacts (technical, economic, environmental and social). A national collaborative strategy is required to address the several options that exist for the development and application of 2020 mining technology. Key issues in implementing 2020 mining technology will also relate to human resources, in terms of employment, skills and education. A need exists to proactively prepare for 2020 through development of a comprehensive education and training strategy.

Jan 1, 1998

. E. P. MATHEWSON, New York, N. Y.-I would like to call attention to the excellent plan for protecting the lining of the tanks from rough handling by the excavator. Many engineers, when considering mechanical excavators for lead-lined tanks, have been afraid that the machinery might get out' of order and rip out the lining. This difficulty seems to have been entirely overcome in this installation, and those who have been responsible for its success deserve a great deal of credit. A. F. CASE,* Cleveland, Ohio. (written discussion t).-The application of the automatic unloader to the copper leaching process at Ajo was a very radical departure from the common use of this machine, inasmuch as the only previous use of this device has been in connection with the unloading of coal and ore from vessels on the Great Lakes. There are many phases in connection with the unloading of ore from lake vessels that are not presented in the extraction of ore tailings from leaching vats. For instance, in unloading from boats, it is necessary to provide means to reach under the hatches to parts of the cargo hold which do not lie directly under the hatches, and to work in inaccessible places that do not exist in a leaching vat. These necessities require complications that could be very easily dispensed with in this new application. On this account the unloader, is applied to the New Cornelia, plant, represents what is probably the simplest development of the machine that has ever been produced, and, manifestly, in its simplest form it could he expected to show results corresponding to its performances when installed with all of its complications. One of the requirements of vessel unloading is extreme vertical travel, when the bucket is required to reach the bottom of the, cargo hold, often 12 or 13 ft. below water-level, and discharge into a receptacle 30 ft. above-the water. This was materially simplified at Ajo for the reason that the vertical travel was never more than 20 ft. This condition immediately resulted in the possibility of shortening the walking beam which carries the bucket leg, and, in fact, in entirely reducing the size of all the working, parts of the trolley, walking beam, and bucket leg, as far as reaches were concerned.

Jan 11, 1918