Search Documents

By A. Hotta

Reduction of CO2 emissions is the key driving force behind the development and implementation of new solutions for energy production. One solution is circulating fluidized bed (CFB) combustion technology combined with a high-efficiency once-through water-steam cycle. Foster Wheeler's CFB technology is today commercially available in capacities up to 800 MWe with ultra-supercritical steam parameters. Simultaneously, the Flexi-Burn® CFB technology is being developed to provide capability of flexible operation in air firing and oxy-combustion for carbon capture. CFB technology can offer an attractive solution for the reduction of CO2 emissions, owing to advantages such as fuel flexibility and low emissions that the air-fired CFB technology offers today. Pilot test facilities provide information about the performance of CFB oxy-combustion technology, and the acquired knowledge is being incorporated in boiler modelling and design tools. One of the European R&D initiatives on carbon capture and storage (CCS) is the Technological Centre for CO2 Capture and Transport, which is supported by the Spanish Government through the Fundación Ciudad de la Energía (CIUDEN). CIUDEN is a research and development institution created by the Spanish administration in 2006 and fully conceived for collaborative research in CO2 capture, transportation, and storage. The Technology Development Centre for CO2 Capture and Transport comprises two technologies on oxy-combustion: pulverized coal (PC) and circulating fluidized bed (CFB). This paper will focus on the design and main characteristics of the 30 megawatt-hour thermal capacity (MWth) oxy-CFB boiler. Foster Wheeler is the technology provider of the Flexi-Burn CFB unit, for which commissioning has been completed in the first quarter of 2011. The CFB unit design allows operation either under conven¬tional combustion with air or under oxy-fuel conditions. The size of this experimental boiler is sufficient to allow the scaling of the results to commercial units. In this way, multiple fuels and operating conditions can be tested economically. The results will validate the design of a future 330 MWe supercritical Oxy-Combustion Power Station (OXY-CFB-300 Compostilla Project) intended to demonstrate the CCS technology at commercial scale. The Compostilla OXY-CFB-300 Project is one of the six CCS demonstration projects funded under the European Energy Programme for Recovery (EEPR) of the EU. The project is based on a future 330 MWe CFB supercritical oxy-combustion plant, with CO2 storage in a deep geological formation. The first phase of the project, granted by the EEPR programme and led by the Spanish utility ENDESA, includes all studies and characterization work needed on CO2 capture, transport, and storage, as well the costs, financing, and regulatory and permitting required, prior to the final investment decision for the construction phase of the plant by the end of 2012.

Jan 1, 2012

By R. J. Charles

Previous study of simple impact systems indicated that energy required for fracture and size reduction of brittle materials is greatly dependent on the type of loading that is employed. In this regard it was postulated that fracture and size reduction of a brittle specimen might be accomplished by a high velocity impact at an energy level at which a low velocity impact would leave the specimen relatively undamaged. The finite time required to propagate energy away from the point of loading of an impacted object to other parts of the object and to its supports may permit a concentration of energy at the point of impact if the rate of loading is high. Localizing of energy at the point of impact could quickly initiate fractures that would propagate through the impacted material along with the traveling stress waves. As the cracks form, the initially absorbed strain energy would be released and portions of it travel ahead of the crack tips as stress waves. These secondary stress waves, combined with the initial stress waves derived from the impact, would produce high localized strain conditions in front of the fracture zone. The fracture zone would propagate and the specimen shatter. High rates of loading are brought about by short impact times, in turn obtained by employing high velocity projectiles that are of small mass compared to the impacted object.

Oct 1, 1956

By Hallan Marsh

THE subject of this paper is apt to bring to mind wells ranging from 6000 to over 8000 ft. in depth. However, it is uncommon to pump wells at depths greater than about 5000 ft. Fig. 1 shows the number of wells being pumped at various depths by one company in Southern California. FIG. 1.-NUMBER OF WELLS BEING PUMPED BY ONE COMPANY FROM VARIOUS DEPTHS IN SOUTHERN CALIFORNIA. A few companies have a very few wells pumping at depths greater than this. This paper will deal with wells between 3000 and 5500 ft. in depth. Most California oils at these depths are between 25° and 35 gravity. The subject is so broad that it will be necessary to omit many interesting phases, and to treat others very briefly. Power, power transmission equipment, power efficiency, counterbalancing, sucker rods, pumps and volumetric efficiency will be discussed.

Jan 1, 1928

By M O. Tade, M W. Sze

The particle dynamics of a mixture of coal and zircon system wasstudied in a scaled-down cold model of an industrial kiln. Thefactors investigated in the study were rotational speed (N),zircon-to-coal feed ratio (B), coal particle size (dpc) and the angle of inclination (*) of the kiln. The technique used is the residence time distribution (RTD) method. It was found that rotational speed and angle of inclination are important parameters that affect the residence time of particles in the kiln. A mathematical model for predicting the mean residence time of particles in the rotary kiln was developed. Comparisons with reported models for such systems are discussed.

Jan 1, 1998

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

By J. R. Donald, K. Scholey

"Nickel has been mined and processed from the Sudbury basin for over 100 years. During this period, the process has evolved into what is one of the largest and most complex mining and metallurgical facilities in the world. This paper will describe the geology and mining of the Sudbury basin as well as the Copper Cliff metallurgical flowsheet circa 2005, including:•,Clarabelle Mill,•,The flash smelting furnaces,•,The bulk converters,•,Matte casting, separation, and processing•,The carbonyl refineries•,Carbonyl residue processing•,Copper processing•,Sulphur productsThe challenges of today and the opportunities for the future are discussed."

Jan 1, 2005

By Bethany Witter

In the past decades, a technological explosion has caused generational shifts. First, millennials experienced a technological shift to computers and cellphones. Next, Generation Z experienced a shift to smart phones and social media. These two generations are immersed in technology and are accustomed to constant connectivity. How do the extractive and construction industries gain the interest of younger generations and integrate them into the industry? The Virginia Tech Student Chapter of the International Society of Explosives Engineers handled this same issue with its recruitment efforts and event planning from 2017-2019. The first critical component of integrating Generation Z college students into the extractive industries is clear and frequent communication via email. Next, Generation Z often values the motivation behind work when choosing a career, so advertising technological advancements, benefits, and ways people can contribute to improving the industry also helps attract young generations. Similarly, advertising opportunities for people to work outside with their hands, travel, and secure stable careers can attract students. At Virginia Tech, the most effective way to attract and maintain the interest of students in extractive industries is to put the students in the field. Field trips to mines and factories experienced the most stable attendance and highest survey reviews of all other chapter events. Guest presentations from industry professionals were often well attended, but attendance tapered off as the academic year progressed and students grew busier. Periodic trips throughout the year maintained student engagement and often supplemented their curriculum. The student chapter was relatively successful in attracting students, but it struggled to maintain attendance levels in the latter portion of the academic year. In the future, the industry can increase its recruitment of Generation Z and Millennials into the workforce by working more closely with university programs to provide resources and opportunities for hands-on experiences for students.

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By Mayer G. Hansen

A series of papers dealing with diamond drilling practices, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines, is to be published as information circulars by the bureau. This paper, the first of the series, describes the general practice at the United Verde mine during the last ten years; specific instances cited in the paper refer to 1930, the last year of full operation. The United Verde copper mine is located at the town of Jerome, Yavapai County, north central Arizona.

Jan 1, 1933

By Victor L. Steven

10.1-SHAFT SINKING AND RAISING BY CONVENTIONAL METHODS VICTOR L. STEVEN 10.1.1-SHAFT SELECTION A great deal of thought and planning should go into the selection of a mine shaft to provide the most effective use over the greatest, period of time. It sometimes is better to make an additional capital expenditure in the initial shaft program to achieve the greatest overall shaft usage. It is possible to sink a shaft which could be used for mine development, and initial production and later convert it to a ventilation, service or escape shaft. It is important to consider a second shaft in the original planning to provide ventilation, an escapeway and services for overall efficient production and safety. A second shaft usually is required to comply with state and federal mining laws. The main items to consider in shaft selection are: 1. Installation from surface or underground. 2. Vertical or inclined (sec Sec. 10.1.4L for discussion of factors involved in choice). 3. Tonnage to be hoisted. 4. Size of mining equipment to be lowered through the shaft to the underground workings. 5. Amount of water to be handled in the mining operation. 6. Ventilation requirements. 7. Type of ground the shaft is to be sunk through. 8. Position of shaft with relation to ore body. After the main features of a shaft arc determined, such as vertical or inclined, shape, size, type of lining and support, compartments, and shaft. facilities (air, water, ventilation, pump lines, power cahles, etc.), then :I sinking plant and procedures should be planned. At this point it should be decided whether the company will sink the shaft with its own crews or award the job to a competent shaft contractor. Company sinking generally will cost less if competent shaft men are available. Money also will be saved in plant costs, such as for hoist, headframe, compressed air, buildings, etc., as these will be part of the permanent plant and can be used in the sinking operation. Labor costs generally will be lower than contractor construction rates. The advantage of having a contract, or is the speed of completion of the project. Contractors usually have headframes and hoists ready to move on the job immediately and have trained crews ready to complete the project in the shortest possible time. Next, the type of surface sinking plant (hoist, headframe, etc.) should be selected and a determination made whether it is to be temporary or permanent. In most cases it is less expensive to install the permanent, headframe and hoist, and use them for sinking. The type of actual sinking equipment to be used should be evaluated for the most efficient sinking cycle, e.g., mucking method, drilling method, and lining or support means. The proper cycling of drilling, mucking and lining is extremely important in obtaining the most favourable sinking costs. 10.1.2 - GROUND STABILIZATION AND WATER CONTROL Prior to the shaft-sinking operation an investigation should be made into ground-water conditions. If water is anticipated, then pregrouting of the ground

Jan 1, 1973

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017

By V.F. Marsters

Seepages of oil in Ecuador have been known for many years. The locality first to receive attention, and still worked in a modest way, lies on the north shore of the Santa Elena peninsula, between La Puntilla and Salinas. Operations mere first conducted largely by local cdpital. Later, foreign companies acquired large blocks of land, where they have done considerable drilling. For details concerning present drilling activities in Ecuador, we are indebted to Leon Price, an Ame~ican resident engineer of Ecuador. The information solicited came to the author through the office of the American Consulatell with permission to use it. The coastal plain bordering the Province of Tumbes, Peru, continues to the northeast, but narrow on passing the Zarumilla River. From this point northward it widens toward Santa Rosa. In fact, the pampas, as shown on the official Wolf map, correspond fairly well to the areal extent of tbe coastal plain as far as Guayaquil. This is shown in a general way on the accompanying map. The author understands that the Guayaquil enlbayment is bordered on all sides by the coastal plain, as recognized at Tumbes and farther southwest, and that it can be followed without a break as far north as Palmar. This view is supported by the mapped area regarded by Mr. Price as favorable or possible oil territory. Moreover the islands in the Gulf of Guayaquil are the same geologically as the coastal edge, being composed of Tertiary sediments. The author understands also that Tertiary formations occur north of Palmar. According to a report by Mr. Cardon, of Guayaquil, Tertiary sediments are exposed in the region of San Francisco and extend to and beyond Pta. Calera. There is also reason to believe that at least the lower part of the valley of the Santiago River is occupied by Tertiary sediments, ~~hich probably border the const line and extend into the River Mini l)nsin, and into Colombia. On the south coast there are many seepages, most of them near the inner edge of the coastal plain, between Zarumilla and Santa Rosa and also between Santa Rosa and Machala. I11 the latter region are

Jan 1, 1923

By V. F. Marsters

Seepages of oil in Ecuador have been known for many years. The locality first to receive attention, and still worked in a modest way, lies on the north shore of the Santa Elena peninsula, between La Puntilla and Salinas. Operations mere first conducted largely by local cdpital. Later, foreign companies acquired large blocks of land, where they have done considerable drilling. For details concerning present drilling activities in Ecuador, we are indebted to Leon Price, an Ame~ican resident engineer of Ecuador. The information solicited came to the author through the office of the American Consulatell with permission to use it. The coastal plain bordering the Province of Tumbes, Peru, continues to the northeast, but narrow on passing the Zarumilla River. From this point northward it widens toward Santa Rosa. In fact, the pampas, as shown on the official Wolf map, correspond fairly well to the areal extent of tbe coastal plain as far as Guayaquil. This is shown in a general way on the accompanying map. The author understands that the Guayaquil enlbayment is bordered on all sides by the coastal plain, as recognized at Tumbes and farther southwest, and that it can be followed without a break as far north as Palmar. This view is supported by the mapped area regarded by Mr. Price as favorable or possible oil territory. Moreover the islands in the Gulf of Guayaquil are the same geologically as the coastal edge, being composed of Tertiary sediments. The author understands also that Tertiary formations occur north of Palmar. According to a report by Mr. Cardon, of Guayaquil, Tertiary sediments are exposed in the region of San Francisco and extend to and beyond Pta. Calera. There is also reason to believe that at least the lower part of the valley of the Santiago River is occupied by Tertiary sediments, ~~hich probably border the const line and extend into the River Mini l)nsin, and into Colombia. On the south coast there are many seepages, most of them near the inner edge of the coastal plain, between Zarumilla and Santa Rosa and also between Santa Rosa and Machala. I11 the latter region are

Jan 1, 1923

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

By J. B. STEWART

T HE position of each hole of any series of holes was carefully located by the surveyor, plotted in plan and elevation, and numbers assigned to them. The second series was staggered halfway between the first and so on for each succeeding series. Two and a, half to three months was frequently required to grout a series of holes calculated to insure safety for sinking a distance of 10 meters or say 33 ft. Naturally the initial operation called for drilling and grouting two series of holes but thereafter each sinking campaign required only one series of holes as shown in Fig. 8. The pump handling about 75 gal. per minute corresponds to 46 tons of grout or 6 tons cement delivered as a fair over-all average for the 24 hours. Thus 600 to 800 tons of cement was used for a single section of 33 ft. depth of shaft. One campaign used nearly 1100 tons of cement. Some holes were effectually sealed with as low as 30 tons, while many required 60, and some 80 to 90 tons.

Jan 1, 1926

By C. Musingwini, C. Beaumont

"Kansanshi mine, located in northwestern Zambia, uses conventional openpit mining to produce primarily copper, with gold as a by-product. The ore is extracted from a deposit with highly complex mineralogical suites that are difficult to process, sometimes leading to poor recoveries. The mine was using an ore classification system called ‘Mat-Type’, which classified various ore types into 22 different quality categories, ranging from poor to good quality. Ore with poor recovery was classified as ’poor quality’ ore and directed to long-term stockpiles. Due to a lack of proper integration between the technical and functional areas forming the mine value chain, Mat-Type unintentionally misclassified ore. A geometallurgical analysis was therefore undertaken to review Mat-Type and a new geometallurgical ore classification system, called ‘OXMAT ’, was developed to replace Mat- Type.When implemented, OXMAT eliminated nine of the 22 ore categories and the remaining 13 ore categories could now be more accurately and consistently defined, leading to a significant change in the quantity of ore being mined. OXMAT demonstrated that within a defined test volume of the geological model, waste tonnes could be reduced by 19% while ore tonnes could be increased by 17%. This paper therefore demonstrates the value created through integrated geometallurgical modelling. IntroductionKansanshi mine is located in northwestern Zambia, approximately 10 km north of the provincial capital Solwezi and about 160 km west of Nchanga mine in the Central African Copperbelt (Broughton and Hitzman, 2002). The location of Kansanshi mine relative to other major copper deposits in the Copperbelt is indicated in Figure 1.Kansanshi mine uses conventional openpit mining methods to exploit copper- and gold-bearing veins hosted in a structurallycontrolled mineral deposit. Mining is carried out in two areas of the deposit, the Northwest and Main pits. A third area of the deposit, called Southeast Dome, is currently not being exploited (Figure 2)."

Mar 1, 2019

Anglo Platinum commenced commercial underground borehole radar (BHR) surveys during 2006 following a series of trial surveys using both the ?slimline? Geomole and Aardwolf systems. Current borehole radar systems comprise radio frequency transmitter ? receiver antennae operating at 30 -100MHz that measure the time taken for a transmitted pulse to traverse a rock volume and be received (Fig 1). The time taken can be converted to distance if the transmission speed of the pulse through the rock volume is known. The transmitted pulse may be reflected off a suitably orientated geological reflector (in reflection mode) or may be recorded in receivers located in other boreholes (cross-hole tomographic mode). In the Bushveld Complex lithologies, these radar systems have ranges of 30-50 metres in reflection mode depending on the electrical properties of local stratigraphic units. Both the Merensky Reef (MR) and the underlying UG2 have been shown to act as reflectors, which offer the opportunity of using BHR as an imaging or mapping tool. Reflection of the radar signal occurs wherever a strong contrast in dielectric constants occurs such as between norite and harzburgite or where chromitite stringers are present. [ ] Fig 1 Main elements of a borehole radar system Much experience has been gained in the practical application of BHR surveys in platinum mining. The value of a BHR survey is that it provides a continuous line of information to ?connect the dots? rather than a few discrete pierce points. BHR surveys can be used to mitigate risk in three crucial areas: ? Mine planning at the strategic as well as tactical level ? geotechnical evaluation of proposed shaft sites, detailed profiling or mapping of reef and disruptions of the reef such as faults, rolls and potholes; ? Mineral resource classification ? identification of structural discontinuities in orebodies affecting resource classification e.g. potholes and reef facies; ? Safety ? identifying areas with poor ground conditions that are often associated with faults, dykes and potholes.

Jan 1, 2007

By Éric Létoumeau, Julie Fournier, Sylvain Caron, Yves Breau, Martin Plante, Dominique Girard, Luc Tardif, François Robichaud

"Since 1999, COREM (formerly the Centre de Recherche Minérale) has conducted and coordinated research and development activities for a consortium of mining companies that uses the benefits and advantages of collaborative pre-competitive research. In particular, COREM’s “In Situ Optimization Group” is involved in the development and implementation of modem information technologies related to process optimization and control.The POP Project was launched in order to increase and consolidate the use of such technologies applied to mineralurgical and metallurgical processes. To ensure a successful transfer to the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM’s members and are grouped into three main modules:- R&D Module: research and development in universities and research centres;-Technology Transfer Module: integration of new tools into the POP Software, industrial applications and technical support;- Training Module: education of new engineers in universities and continuing education of plant personnel through on-site workshops.This paper outlines the opportunities that led to the definition of the POP Project, presents its main objectives and describes its main modules. The main features of the POP Software are outlined, the first applications at COREM’s member plants are presented and, finally, future developments are discussed."

Jan 1, 2002

By Boden A

A procedure was developed for recovering metal values from copper-smelter fume. The fume is first leached to neutrality with dilute sulphuric acid to obtain a solution of zinc sulphate containing a low level of impurities. The tailings from this leach are treated with hydrochloric acid in two stages, in which tin and zinc are quantitatively leached and recovered as a tin concentrate and a zinc sulphatelzinc chloride solution.About 80 per cent of the lead sulphate is converted into lead chloride, which can be recovered as a pure product.Data on the effect of temperature, acid concentration, aeration, and solid/liquid ratios on the hydrochloric acid leach are presented, and the fate of the most important metals during the recovery process is described. Alternative treatments of the tailings from the neutral sulphuric acid leach were briefly investigated.

Jan 1, 1977

Some form of technical library is a necessity for every metallurgical plant, but its form and scope will vary with the conditions of each case. In its simplest form, it may consist of one or two mining journals and a few text books distributed amongst the staff. Again, it may be a separate establishment controlled by a clerk, the technical staff necessarily making its own research into the literature available. A still more elaborate organisation may be established both to supply information when requested and to keep the operating staff in touch with current matters of interest, and the library service of the Electrolytic Zinc Co. of Australasia is of this character.The necessity for such a service is due to several facts. The Company's interests are scattered over three States. Most of its staff members are remote from: good public library facilities and they have few opportunities for exchanging ideas verbally with other metallurgists and engineers. Then, too, the process of recovering zinc by electrolysis, is a young art of which the physical and chemical bases were far from fully known at the time the: Risdon plant was established. Most of the zinc produced is sold abroad, and this unsheltered industry can afford to miss no technical or economic development which may promote its efficiency. Add to these facts the geographical isolation of the Commonwealth and the case for an adequate library is complete.

Jan 1, 1934