Search Documents

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By T. L. McCall

CHANGES in mining practices have evolved so quietly and unobtrusively that perhaps we scarcely appreciate how truly startling these changes are unless we cast our minds back so as to compare the past with the present. Such retrospection is, indeed, necessary when attempting to forecast the future, for it is only by carefully reviewing the past that we can hope to obtain an indication of what the future may hold in store. In this instance, it is not necessary to delve into the very early history of . coal mining, as our purpose will be served if the last three or four decades are reviewed, a period that is still fresh within the memory of many of us. These earlier days might be termed the selective period of mining, for at that time the coal resources of the world had not been tapped to anything like the extent they are at present and this condition enabled the owners and operators to exercise selective powers and only mine such seams of coal as could be most easily reached an worked at the lowest possible cost and which, at the same time, would suit the requirements of the market. Carrying this thought of selective mining still further, the miner, who was then an artisan skilled in all the branches of his calling, was able to select or discard such parts of the seam he was working that the co al sent out of the mine was acceptable to the consumer with just the barest minimum of preparation. Compare these conditions with the? conditions prevailing today, when coal seams of medium height, good quality, and readily accessible have been largely depleted and the operator has been compelled either to carry on his operations under much greater depths of cover where the coal is more costly to win, or else to work seams of lesser height or of poorer quality.

Jan 1, 1938

By AIME AIME

A DOCUMENT of progress and of great interest to engineers is the report of the Military Affairs Committee of 'the Engineering Council, which has just been accepted and sent to the secretary of War. It provides .a plan whereby civilian engineers holding commissions in the Reserve Corps may; with their con- sent, be called into service of the army during peace at any time, either with troops in the field or in a consulting capacity on any government engineering work. The Military Affairs Committee finds ample authority in the military bill passed by Congress on June 4, 1920, for this arrangement and also for extending the privilege to military engineer, officer-s of the regular army to engage in civilian work during times of peace. It is hoped that the Secretary of War will adopt the suggestions and put the program outlined into effect. This is a constructive piece of work comparable to the efforts of the military Committee before the war which developed so much in the way of preparedness, particularly in the program of military lectures which, held in the auditorium in the Engineering Societies Building, became so popular that each lecture had

Jan 1, 1920

By Pablo Altoé Amorim, Bruno Sellitti Borges, Otávio Lube dos Santos, Arthur Pizetta David, Matheus Diogo Penido da Silva

Automation is in everywhere nowadays, including within companies and industries, and is therefore fundamental and essential for production, quality and process control of them. There are many ways to automate a production line or a machine can be through relay logic, Programmable Logic Controllers (PLCs), and even more modern microcontrollers with native Internet of Things (IoT) support can be used. What are the advantages and disadvantages of each approach? A PCB was created using more modern microcontrollers programmed in C, C ++ and Whiting language to simulate a replacement of a PLC in an actual machine. Having a very positive result, being able to handle the machine manually via Wi fi besides being able to also perform a real-time monitoring of the machine's motors through the mobile phone, thus entering the IoT and fitting into the Industry 4.0.

Oct 1, 2019

By CORNELIUS STEPHANUS LODEWYK SCHUTTE, WIEHAN ADRIAAN PELSER, JEAN HERMAN VAN LAAR, MICHAEL DAVID HARMSE

Rising electricity costs in South Africa have resulted in a need for optimized compressed-air networks in the mining environment. As a result, the financial benefit of air receivers needs to be reconsidered along with the economic dispatch strategy. This study investigates the use of an evolutionary algorithm in the mining industry to determine the potential financial benefit for various-sized air receivers, as well as their dispatch strategy. A genetic algorithm was selected due to the improved solution reliability and accuracy compared to other optimization techniques. This study indicates that a genetic algorithm can be used to determine the optimal dispatch of compressed air in the deep-level mining industry. Further, this study indicates that air receivers are financially viable in the mining industry and can be used to reduce operating costs, improving profitability.

Dec 1, 2022

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By Graham Speirs

La minería del siglo XXI requiere que ingenieros, consultores y proveedores brinden apoyo a promotores, desarrolladores y operadores para lograr una extracción y procesamiento de minerales segura, eficaz y con el menor costo posible. Este artículo técnico muestra el diseño, construcción y mantenimiento de un eje vertical, con una forma más rápida, económica y productiva de izar con cables guía, buzones de aluminio y sistemas de izado diseñados con tecnología de vanguardia.

Sep 30, 2017

By Valeria Collini, Antonello Mestroni, Enrico Plazzogna

The Danieli Group is deeply involved in the technological improvements stimulated by Industry 4.0 concepts widely applied to the metals industry and process automation. The so-called "Intelligent Mill" is the natural evolution of the company’s consolidated know-how and undisputed leadership in the fields of mini-mill and turnkey plants. Complete and structured data collection is the basis for real-time analysis and process optimization in terms of quality, efficiency and easy maintenance. A centralized repository of information is possible thanks to the strong interconnection between process control system architecture and intelligent sensors, together with dedicated software tools leading to an intuitive approach to data analytics.

Oct 1, 2019

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

By L Neindorf

The development and application of paste fill, cement slurry aggregate fill and shotcrete bulkheads at Mount Isa Mines is described. The progressive changes in filling style in the Mount Isa copper mines from a dry fill based cemented rock fill to tailings based paste fill and slurry fills is explained. The development of shotcrete arched bulkheads and engineered drainage system is described. Details on how Mount Isa Mines has achieved approximately 30 per cent cost reduction in backfill operations through innovations are given. The development of a rocky paste fill is explained.

Jan 1, 2005

By J. R. Soule

"The fluorspar deposits in the Gallinas Mining District, Lincoln County, New Mexico, were examined early in February and again in April 1943 by the Bureau of Mines because of the possible importance of newly discovered deposits and of old mine workings showing fluorite-bearing material. There &re many of these deposits spread over a considerable area, and it appeared that exploration might indicate sufficient reserves to support a local mill that could contribute to the supply of fluorspar needed for war purposes. Accordingly, the Bureau initiated an exploratory program in June 1943, which was completed in August 1944.H. E. Rothrock, Roy Earhart, R. G. Smalley, and V. C. Kelly, geologists of the Federal Geological Survey, began mapping and studying the district in May 1943 and continued this work throughout the Bureau's exploration.David J. Stauffer, district ranger, U. S. Forest Service, and several claim owners assisted in the examinations and subsequent exploration.The fluorspar deposits in the Gallinas Mountains are reached by an unpaved forest road, which, leaves U. S. Highway 54 half a mile south of Gallinas station. The road runs due west for 3 miles, then turns due north just beyond the first cattleguard. This north branch is followed for 2 miles to a second cattleguard. There a left branch extends northwest up Red Cloud Canyon to the Red Cloud, and. All. American deposits; the right branch continues north for 2.miles past the Wade Porter ranch, to another left branch, which goes almost 2 miles west to the Hoosier Group deposits. The remaining deposits are reached by trail from either the Hoosier Group or, more easily, from the Red Cloud claim (fig. 1).The Hoosier Group is in sec. l9,, T.. 1S.,1 R. 12 E.; all of the other known ore occurrences are in secs. 13, 14, and 23 to 27, inclusive, T. IS., R. 11 E. All of the deposits are in the Lincoln National Forest and within the limits of a State game refuge. The nearest railroad loading point is Gallinas, Station on the Southern Pacific Railroad. Corona, the next station north of Gallinas, is a Mile or two farther from the deposits.Minor supplied, telegraph, telephone, freight, and express service, and limited living accommodations, Are, obtainable at Corona, 10 to 15 miles from the deposits of Carrizozo, N. Mex., 50 miles south."

Apr 1, 1946

By Richard A. Dick

In this report commercial blasting compounds are classified according to their nitroglycerin (or equivalent explosive oil) and ammonium nitrate content as dynamites, gelatins, blasting agents, military explosives, and blasting , accessories. The ingredients and more significant properties of each explosive are tabulated and briefly discussed. Data are summarized from various handbooks, textbooks, and manufacturers' technical data sheets, together with the author's personal experience; however, this report is not intended to be a technical handbook, since it does not deal with blasting techniques. Instead, it seeks to acquaint the reader with the great variety of explosives, available, their advantages and disadvantages, and their general areas of application. Properties discussed are weight strength, cartridge strength, detonation velocity, density, detonation pressure, water resistance, and fume class. The weakness of the strength rating system and the importance of detonation pres- , sure, density, and detonation velocity in rating explosives are discussed. The terms "blasting agent" and "slurry," which are often misused, are defined. Trends indicate that blasting agents (that is, blasting mixtures with none of of the ingredients singly classified as an explosive), particularly high-density slurry blasting agents, will dominate the explosives field in the future.

Jan 1, 1968

By J. J. Cilliers, I. K. Craig, J. D. le Roux, K. Hadler

An analysis of the state-observability characteristics of a dynamic tank-to-tank model of a flotation bank indicates that the concentrate-flow rate of each tank can be estimated from accurate measurements of the pulp height in each tank and the final tailings flow-rate exiting the final tank. Therefore, there is an opportunity to construct an observer (model-based soft-sensor) which can estimate the concentrate flow-rate of tanks in a flotation bank. The concentrate flow-rate, i.e. mass pull, is generally measured by means of froth image analysers on industrial plants. A model-based soft-sensor will not only provide a means to validate froth image analyser results, but could potentially substitute them as they are less expensive to implement and maintain. Keywords: Concentrate flow-rate, estimation, flotation, modelling, observability, soft-sensor

Jan 1, 2020

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By Dong Liang, Honggang Zhong, Zhenxing Yin, Qijie Zhai

"2507 super duplex stainless steel (SDSS) has been widely applied in a marine environment, attributing to its excellent pitting corrosion resistance and mechanical properties which are particularly determined by the nitrogen precipitation behaviors and volume fraction of ferrite. In this paper, various cooling rates were obtained by applying four different moulds with the common gating system. By which the influence of cooling rates on nitrogen precipitation behaviors and the ferrite fraction in cast 2507 SDSS was comparatively investigated. The results showed that nitrogen porosity could easily precipitate in cast 2507 SDSS under standard atmospheric pressure. The number of nitrogen holes increased with decreasing the cooling rates, and the holes mainly distributed in three zones, i.e. the interface between the horizontal and vertical columnar grains, top vertical columnar grains and the final solidification region. Additionally, higher ferrite fraction was obtained with lower cooling rates.IntroductionDuplex stainless steels (DSS) have a dual-phase microstructure consisting of ferrite (d) and aus-tenite (?). Due to the combined advantageous properties of d and ? phase, their application rapid-ly increased in industry [1, 2]. Super duplex Stainless Steel (SDSS) is the third generation of du-plex stainless steels, of which the alloy elements Cr, Ni and N content are higher than the stand-ard 2205 DSS. Because it has high contents of alloy elements, the SDSS has better mechanical properties, and its pitting resistance equivalent number (PREN) reached a point 43. Hence SDSS has been used in petroleum chemical industry, the marine equipment and harsh corrosion environments [3]. SDSS contains ferrite stabilizing elements, such as Cr, Mo and Si, and austenite stabilizing elements like Ni, Mn and N [4]. Many researchers have studied the effects of these elements on the stabilization of d and ? phase and the ratio of the two phases. High nitrogen con-tent is another prominent feature of SDSS. Nitrogen addition to SDSS is very effective for improving its mechanical properties [5] and corrosion resistance [6], such as pitting resistance in NOx environment. To increase the nitrogen content in steels, a lot of work had been done. N. Nakamura and S. Takaki [7] examined the behavior of nitrogen absorption in Fe-23Cr alloy powder by sintering in nitrogen gas atmosphere, they found nitrogen content easily up to 1.0 wt. %. Using devised NH3 gas injection system, W. Park et al. [8] successfully produced austenitic Fe–23.5Cr alloys containing over 3 wt. % of nitrogen. Further-more, W.P. Tong et al. [9] stated that nitrogen percent was extraordinary high (about 10 wt. %) in pure iron plate. However, the above methods are difficult to be applied to large-scale industrial production."

Jan 1, 2012

By Li Qihou, Li Yuhu, Liu Zhihong, Liu Zhiyong, Yang Xiaofeng

Scorodite samples were synthesized, in adding or without crystal seed respectively by using Atmospheric Scorodite Process (ASP), Hydrothermal Scorodite Process (HSP), and Improved Atmospheric Scorodite Process (IASP) individually; and their crystal structure, crystallinity, morphology, particle size, specific surface area, Fe/As mole ratio, as well as the leaching stability were characterized, aimed to reveal the relationships among the synthesis methods, the compositional and structural properties, and the leaching stabilities of scorodite. The results show that synthesis methods have significant effects on the compositional and structural properties of scorodite. Scorodite samples of high crystallinity, small specific surface area, and low Fe/As mole ratio, possess high leaching stability. The order in the leaching stability of scorodite samples synthesized in this study is as follow: ASP<HSP<IASP. Scorodite particles in the sample synthesized by IASP without crystal seed are in large sizes and of pyramidal morphology enclosed mainly by crystal planes of {111}; and the sample possesses the crystallinity of 84.5%, the particle size (D50) of 28.2 m, the BET specific surface area of 3.72 m2/g, and the Fe/As mole ratio of 1.05; after leaching this sample by using acetate buffer solution of pH 4.95 for 10 days, the total arsenic concentration in the leaching solution is merely 1.14 mg/L.

Jan 1, 2015

By H Law, M Muller

Mount Isa Mines (MIM) Copper Concentrator currently utilises Agitair 120 banks for its roughing flotation circuit. Apart from a rotor change, the only other significant work completed to the Agitair banks since their installation and commissioning over 40 years ago has been a like for like refurbishment in 2016. The Agitair banks at the MIM Copper Concentrator currently utilise the Pipsa rotor design which progressively replaced the original Chile X rotor design in the 1980’s and 90’s in the copper concentrator. Since the development of the Pipsa rotors, modern rotors such as the Dorr-Oliver (DO) high shear rotors have been released to the market with proven recovery and concentrate grade improvements over previous rotor designs. This paper aims to detail the installation, testing and comparison of Pipsa versus Dorr-Oliver rotors in two different flotation sections of the MIM Copper Concentrator.CITATION:Muller, M and Law, H, 2018. High shear rotor trials in the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 393–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996