Search Documents

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By J. F. Dorion

This paper presents the results of on-going investigations on the performance of support systems in Québec underground mines. The focus of these investigations is on site observations complemented by laboratory investigations. Of particular interest is deducing the corrosion rate, at selected mine sites, as determined by the installation of monitoring coupons.

May 1, 2009

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958

By Kermit Allen

Historically, major natural gas transmission companies have been faced with the problem of meeting peak demands when the source of natural gas is located hundreds of miles away from the marketing area. Transcontinental Gas Pipe Line Corp.'s position was further complicated when offshore gas supply wells were shut-in during hurricane alerts. Transco's solution to this problem was the construction of salt storage wells adjacent to their pipeline near Eminence, Miss. Storage caverns were constructed using conventional solution mining methods. Two 13 3/8-in.-diam cased wells were completed and a 1,000,000-bbl cavern was leached at an interval of 5700 to 6700 ft at the base of each well. The two caverns have a usable storage volume of 2.0 billion cu f t and each well has a deliverability rate of 375 million standard cfd. The caverns are unique in that brine is not used for product displacement-all brine has been removed from the caverns. Natural gas is stored at a maximum pressure of 4000 psia. During withdrawal the cavern pressure drops to a minimum of 1225 Asia-the volume of gas between these two pressures becomes "usuable or top gas." The Eminence storage terminal is located on the Eminence salt dome about 30 miles north of Hattiesburg, Miss. Construction began in July 1968 and was completed in October 1970.

Jan 1, 1972

By C. S. Gundewar

Indian National Steel Policy envisages ambitious three fold rise in steel production by the year 2020. This paper covers the iron ore industry in India which cater to the need of iron ore requirement of Indian iron and steel sector as well as export commitment in addition to addressing the industry?s key concern to attain the same. The main contents are (i) resources and its exploitation; covering status of exploration, reserves and resources, province wise occurrences, distribution, nature of mineralization and generation of fines, etc ; (ii) use of iron ore in iron and steel making, covering physical and chemical requirements for pig iron and sponge iron production; (iii) ore characteristics and beneficiation practice in vogue; (iv) projected steel demand and requirement of quality iron ore and provision thereof; (v) recovery of iron values from in situ low-grade ores and stacked fine rejects (-10/-6 mm) inclusive of slimes (-0.15 mm) from tailing ponds; (vi) agglomeration of fine concentrates preferably by pelletization; (vii) measures to augment iron ore availability for future requirements.

Sep 1, 2012

By John C. Hartley

Large areas of the anthracite beds in the Wilkes-Barre, Pa., region have been first-mined in such a manner that over half of the original coal has been left underground as pillars to support the overburden. To recover the maximum amount of this remaining coal, improved devices to support the roof while pillars are being extracted are needed. Also needed are suitable backfilling systems that will stabilize the strata during the mining and effectively limit the inevitable subsidence after pillars are removed. Accordingly, the Federal Bureau of Mines furnished 400 yielding steel props that had been purchased abroad, where this type of prop had been used successfully. The cooperating company arranged for concurrent tests with a mechanical stower designed and built by an American manufacturer. In the area in which the experiments were conducted, pillar removal, using conventional timbering, was most difficult because the roof fractured badly, the installation of timbers consumed a substantial part of the work effort, and some coal nearly always was lost. With the application of the yielding props, the time needed for securing the roof was reduced 33.9 percent; production per man-shift was in¬creased over 33 percent; coal recovery was improved more than 9 percent; and the convergence between roof and floor, during mining and backfilling, amounted to as much as 8.03 inches without any break in the roof. However, in September 1953 some roof rock fell in pillar 10 owing to insufficient props in a small area where the ends of three top holes drilled in the coal face extended up into the roof rock.

Jan 1, 1956

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By R. H. Lien

The Bureau of Mines, U. S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains <l ppm CN and 20 ppb Se; concentrations of other major contaminants meet EPA drinking water standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85 pet of the cyanide. Exploratory research shows that other bacteria removed up to 79 pet of the selenium from chemically oxidized, low-cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By A. B. Cecala

The Bureau of Mines has developed a pallet loading dust control system designed to lower the dust exposure of workers during the bag stacking process at mineral processing facilities. The system makes bag stacking much easier because the pallet height remains constant throughout the entire bag stacking cycle through the use of a hydraulic lift table. The system uses a push-pull ventilation technique to capture the dust generated during bag stacking. A low-volume, high-velocity blower system operating at approximately 150 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-in air jets (approximately 1,200-ftjmin velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they entrain the dust generated during bag stacking. The exhaust ventilation system pulls approximately 2,500 cfm of air and dust through the exhaust hood. This exhaust air can then be dumped into a baghouse ventilation system, or filtered before being discharged outside the mill. During a laboratory evaluation, a 70-pct dust reduction was recorded for the bag stacker. The system was then evaluated in an actual working environment. The first field evaluation was performed at a silica sand operation in which one worker performed the entire loading and bag stacking process. This worker&apos;s dust exposure was lowered 76 pet when using the new pallet loading system. The second field evaluation showed only moderate dust reduction, but this was mainly attributed to an overriding problem associated with background dust and the cleanliness of the bags. From both the ergonomic and production standpoint, the system was well received by both the workforce and plant management.

Jan 1, 1988

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled&apos; condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O&apos;Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator&apos;s judgment of the correct &apos;colour&apos;. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By S Dirdjosuwondo, R Plaisance, L Thoma

PT Freeport Indonesia, a subsidiary of New Orleans-based Freeport McMoran Copper and Gold of New Orleans, operates a large mining complex on the Western half of the Island of New Guinea in Tembagapura, Irian Jaya, Indonesia. The IOZ (Intermediate Ore Zone) mine, one of the underground orebodies, is mined by block caving. The area affected by the cave collects a large quantity of rain and ground waters mixing with fine rock particles. The mixture, commonly called æwet muckÆ, sometimes spills into drawpoints and makes the working environment hazardous to the loader operators. Wet muck is observed in an increasing number of drawpoints in the IOZ mine and remote LHD (Load-Haul-Dump) technology has been implemented to handle the ore. The driving force for this automation project has been the safety of the loader operators. The system has been developed mainly in-house and incorporates state-of-the-art features. Up to eight remote loaders and nine rock breakers are controlled from an underground control room located approximately 400 metres from the active extraction panels. The two underground crushers and nine conveyor feeders are also operated remotely from an adjacent control room. The development of FreeportÆs remote system has taken time and considerable effort. Not only the success of the IOZ mine was at stake but also the fulfillment of environmental commitments pertaining to the mill tailings. Approximately eight per cent of the mill feed must come from underground skarn deposits to neutralise the acid-generating tailings generated by the huge Grasberg open pit ores.

Jan 1, 2000

By Geoffrey Brooks, Mehedi Bin Mohammad, M. Akbar Rhamdhani

Molten alkali nitrates are used commercially as thermal storage fluids (HTF) for solar thermal electricity generation. Their range of operation is limited by the thermal stability and this limits the energy (steam-Rankine cycle) efficiency of these processes. In this study, the effect of atmosphere on the thermal stability of nitrates was investigated using simultaneous thermal analysis techniques (STA). The use of oxygen (O2) as a blanket gas was found to delay the decomposition point of the ternary NaNO3–KNO3–LiNO3 (13.23–57.14–29.63 weight ratio) mixture by 55 °C. By which operating range will increase 65 °C more compared to the binary solar salt. Higher heating rates increased the decomposition point but had less effect on premelting and melting properties. Nitrogen monoxide, and O2 evolution after melting indicates concurrent reversible reactions. Similar phenomena were observed for single and binary nitrates. The eutectic melting point of ternary nitrate obtained from the STA agreed well with FactSage eutectic composition prediction.

Mar 1, 2017

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By David Schlain

"INTRODUCTION Electrolytic manganese is produced by electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell, metallic manganoese being deposited on the cathodes and sulfuric acid produced at the anodes. The spent electrolyte is used to leach fresh ore that has previously been subjected to a reducing roast; the resulting leach liquor is purified and returned to the cell.The leach liquor produced at the Bureau of Mines pilot plant 3/ at Boulder City, Nev., contains 135 to 140 grams of ammonium sulfate and 32 to 36 grams of manganese (as sulfate) per liter, and has a pH of about 2.5. After neutralization to a pH of 6.4 to 6.6 with ammonia and thickening, 0.10 to 0.15 gram of hydrogen sulfide per liter is added to the liquor to precipitate the heavy metals, and after 15 to 30 minutes the precipitate is filtered off. Residual sulfides and colloidal material are removed by ferric hydroxide formed by adding a small amount of ferrous sulfate to the solution at a pH of 6.5 to 7.0 and passing air through it. The solution is then filtered and clarified as a precoat filter. Finally, 0.1 gram of sulfur dioxide per liter is added, and the solution is electrolyzed in an anode-in-diaphragm cell. The spent electrolyte coming from the cell contains approximately 10 grams manganese, 135 grams ammonium sulfate, and 45 grams sulfuric acid per liter."

Oct 1, 1946

By AIME AIME

AT the end of September, &apos; the metal-producing industries were almost prostrate, the production of fuels was largely curtailed, there was a fair degree of activity in general manufacturing, while retail trade was moderately good. Looking at industry on the whole, there was a large percentage of unemployment, the degree of which has increased, progressively, month by month since the beginning of 1921. There is the prospect of much destitution and misery this winter; yet while&apos; in some, quarters, idle workers are already being fed from, commissaries; in other quarters profligacy; in "spending continues, unabated. Amid this confusion in conditions there is;&apos; much that appears paradoxical, but in fact it is not so and indeed everything is running pretty true to form: Such activity in production as there is to be seen is mainly in textiles; - leather goods, foodstuffs, etc., i.e., consumption goods for immediate use. Even in hard times 105,000,000 people must buy a good deal of clothing and food. Besides this there is indispensable repair work and- maintenances. Thus, the good business of the year in white lead for painting. The chief uses for the metals, however, are in the production of capital goods, and except for occasional and special reasons nobody in his senses is capitalizing anything at present prices for labor. Hence several millions of men are idle. The impoverishment of Europe and the exhaustion of her credits adds to this by curtailing our export trade.

Jan 1, 1921

By Lewis Carroll

AS he contemplates the numerous good things the hard-working committees have evolved for the 140th Meeting of the Institute, the Editor knows just how the walrus felt when he uttered his memorable, if somewhat lugubrious lines. For there are the Annual Reception and Dinner at the Commodore, &apos;the Gold Supply Symposium, the luncheons, general and special, and the Annual Institute of Metals Lecture, a Round Table on Iron Ore and a wonderful Informal Dance at the Grand Central Art, Gallery, substantial general sessions, a Smoker-and many other things. -Old, friends and new, reminiscences and confidential chats, horizons pushed back by new information and adjusted perspectives, courage revived and ambitions stimulated-one with a flair for the modernistic might make something-or nothing-of the kaleidoscopic preview &apos;of the coming Annual Meeting.

Jan 1, 1931

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016

By Xie Hao

According to its raw materials orthogonal test scheme is designed and a large number of systemic experiments were carried out in order to study the sintering characteristics of three types of fine ores in Kunming Iron&Steel Co.Ltd(KISC). The effects of carbon mixture ratio and basicity on sintering time, agglomeration ratio, physical properties and utilize coefficient were researched via single factor analysis and range analysis. The experimental results show the best mixture ratio of each fine ore. Analysis found that the influence of the carbon mixture ratio is more significant than which of the basicity on the sintering process except agglomeration ratio of foreign ore.

Jan 1, 2009