Search Documents

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Southwestern New Mexico is part of a large belt of Late Cretaceous to Eocene copper porphyry deposits found in Arizona, New Mexico, and Mexico. These deposits are the result of arc magmatism that occurred during the Laramide orogeny. Recently, attention has been brought to other commodities that can be extracted as by- and co-products, many of which are critical minerals. A new compilation of the geochronology of these deposits shows two main pulses of magmatism that produced mineralized deposits and, along with new dates by the author, shines new light on the geologic history of these deposits and the role it plays in critical mineral abundance.

Feb 1, 2024

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

Reynolds Metals Company announced plans to increase its rate of production of primary aluminum by 17 thousand tons per year by the end of February. Other producers were expected to increase operating rates during the first quarter of 1976 (see table 10 pg. 29). CHROMIUM -Under the Trade Act of 1974, a petition was filed July 16, 1975, with the U.S. International Trade Commission (ITC) by the Tool and Stainless Steel Industry Committee for Import Relief and the United Steelworkers of America, AFL-CIO, for import relief for certain stainless and alloy tool steel products. The Commission determined on January 16, 1976, in a report to the President, that increased quantities of imports of stainless steel sheet and strip, plate, bar, and rod and alloy tool steel except ingots, blooms, billets, slabs, and sheet bars were a substantial cause of serious injury or threat thereof. The Commission recommended import quotas for the period 1976 through 1980. The President has 2 months in which to act, with his decision subject to a Congressional override.

Jan 1, 1976

Jan 1, 1880

By E. G. Erspamer

Laboratory investigations were made by the Bureau of Mines on ore containing the sulfides of both mercury and antimony to develop a method or methods for the economic recovery of mercury metal and the concurrent recovery of antimony as metal or salts,. If standard mercury-recovery techniques are applied to such ores, the antimony content interferes with the effective production of mercury metal; further-more, the antimony is lost. This report presents the results of tests on a sample of cinnabar-stibnite ore from the Red Devil mine near Sleitmute, Alaska. Red Devil ore was chosen for the investigation because it is purported to be typical of ores of the Kuskokwim River area, which, in their aggregate, constitute large potential reserves of mercury and antimony. Studies included petrographic, spectrographic, and chemical analyses, gravity-separation tests, bulk flotation of mercury and antimony sulfides, differential flotation, leaching, and furnacing of crude ore and of flotation concentrate.

Jan 1, 1956

By NA NA

None

Feb 6, 2023

By Werner Burger, Marcus Lübbers

TBM development in recent decades has been dominated by increased face pressures, larger diameters and multi-mode functionality paving the way to realize projects deemed impossible before. In addition, the trend towards digitalization does not stop at the tunnel portal. A shortage of skilled personnel and the ever-present wish to increase workplace safety, quality and system performance automation, operatorassist or even autonomous systems have become key development targets. The paper will present the current state of the art in light of these special conditions.

Jun 13, 2023

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993

By Roy S. Celland, K. H. Singh

The introduction of 'post' pillar mining at the Strathcona mine represents a new approach to ground support in cut-and-fill applications. The method has also shown significant economic advantages. It is believed that the development of this concept is one of the few examples where rock mechanics principles have successfully been applied in the development of a stoping method. The paper describes the evolution of this method and contains discussions on the theoretical analysis of the technical, operational and economics aspects of the system. Pillar design procedures and field observations on the practical application of theoretical analysis are also outlined.

Jan 1, 1973

By T. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with pre-benching or serving as the primary stripping tool, dozers can play an important role in driving down mining costs. This paper reviews the application zone of track-type tractors. In addition, it provides tips on site set-up, equipping of tractors, and machine operation which the audience can take home and apply.

Jan 1, 1996

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By W. Gibson Jaworek

Of increasing importance to the student of fuels economics has been the extent to which different primary energy sources can substitute for each other in the various energy markets of the nation. Knowledge of the nature and extent of fuel interchangeability can aid the fuels economist in projecting trends of energy utilization, as well as giving him a better understanding of the past and present conditions of fuel markets. It is also important to the consumer to know just how much flexibility he can maintain in his energy consuming operations. And, finally, various governmental bodies show keen interest in the degree of energy substitutability in determining public policies concerning the fuels industries. The presence of excess fuel production capacity in the United States during the early 1960's indicates that fuel interchangeability should become more prevalent in the increasingly competitive energy markets of the nation. Discussion of fuel intercompetition is almost always restricted to qualitative terms-because of the lack of comparable statistical data, between the different energy sources in geographic or "type-of-use" fuel, markets. There are exceptions, of course, such as, the excellent fuel consumption data which are available on steam electric generating plants throughout the nation. In other sectors, statistics are at best incomplete.' Inmost instances, indirect fuel consumption indicators, such as sales of fuel burning equipment, are extensively used to measure market shares of a particular fuel; however, these indicators are hard to evaluate precisely without prior knowledge of the total competitive market.

Jan 1, 1961

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By H. M. Cyr, T. F. Steele, C. W. Siller

The development of a new metallurgical roasting device is described. It consists of a refractory column into which air is injected at various levels, forming several superimposed fluidized beds with no supporting grates. When pelleted zinc sulphide concentrates are charged, the roasted product needs no further sintering before reduction to metal. WHEN a gas such as air is blown upward with increasing velocities through a loose mass of solid particles, marked changes in the physical behavior of the particles are noted. At first, when the velocity of the gas is insufficient to support any of the solid, the mass constitutes a "fixed bed." As the gas velocity increases until the pressure drop through the bed approaches the effective weight of the bed per unit area, the bed expands until the solid particles are supported by the air rather than by the lower particles. Some vibration of the particles becomes apparent, but little mixing occurs. This condition is called a "quiescent fluid bed." A further increase in gas velocity imparts more separation and more motion to the individual particles until a condition of turbulence is reached. This "turbulent fluid bed" resembles a rapidly boiling liquid with the characteristic highly agitated diffuse surface and many small eruptions of the boiling mass. Different degrees of turbulence can be generated and all produce excellent mixing. The final stage occurs when the gas velocity becomes so great as to create a "dispersed suspension." Here no surface of the mass is defined and the gas carries solid particles out of their original positions. These changing conditions of fluidization have been studied carefully and pertinent nomenclature standardized by a committee of the American Institute of Chemical Engineers.' Many mathematical analyses2-3 have been made of the forces acting in a fluid bed. These analyses are invaluable, especially for the design of column sizes and selection of equipment. However, in a metallurgical process involving solids of many sizes with changing densities, varying temperatures, and changing gas compositions within the bed, calculations based on theory become approximate. Optimum operating conditions then are best determined experimentally. Many applications have been made of the principles of fluid-bed action by mechanical, chemical, and metallurgical engineers. Especially when good con- tact between reacting solids and gases is desired, very effective results are obtained from fluid beds. They permit excellent temperature control and uniformity throughout a mass of solids in fluid action. Heat transfer to walls and any coolers is high, and fast reaction rates are attained because the solid surfaces are continuously swept clean. The main disadvantages of fluid-bed operations are the danger of short-circuiting in a single bed, danger of incipient sintering which stops action, the necessity of avoiding large changes in particle size or density during roasting, and dust losses when particles of the charge are carried out with exit gases. In the metallurgical field the roasting of sulphide ores to form oxides and sulphur dioxide appears to combine several operating conditions which can be achieved to advantage in a fluid bed. Roasting involves a solid-gas reaction where a high reaction rate is necessary for high capacity, where good temperature control is important in order to prevent sintering, where good heat transfer is needed, and where the density of the solids, when changing from sulphides to oxides, is not largely changed. Short-circuiting, however, constitutes a major problem when a single fluid bed is used. Because of the turbulence of the bed, an entering particle may be in the region of the discharge before it is roasted. Hence, to attain a satisfactorily low sulphur in the calcine, a long average residence time with correspondingly low capacity is required. The solution to this difficulty is the use of multiple stages, which in the conventional fluid-bed design requires separate hearths with feed and discharge mechanisms for each stage. A further practical difficulty in fluid-bed roasting of flotation zinc concentrates is their fine particle size which makes a true fluid action without excessive carry-over of dust very difficult to attain, especially when the large air volumes necessary for high capacity are used. A New Design After considerable experimentation in the laboratory and on a semipilot-plant scale, a new method and equipment for roasting were devised which provided a unique solution to these problems. A detailed account of this development appears in the patent literature," and many of the variations of this development reported herein are the subject of

Jan 1, 1955

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following; questions are arising n the minds of coal users: (a) Will the coal lose any of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when storing coal? In regard to the loss of heating value of coal in storage, tests made by the Bureau of Mines show that the loss commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh Gas, and Sheridan Wyoming coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating; Value of Coal During Storage, by H. C. Porter and F. K. Ovitz:

Jan 1, 1942

"The National Mining Hall of Fame and Museum (NMHFM) announced the class of 2019 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exceptional financial acumen in assembling several operations that formed the basis of a successful American mining company; conception and development of equipment which contributed to improved efficiency and mine safety; and unrelenting advocacy for the U.S. mining industry and its workers. These individuals, selected for being determined, forward-thinking innovators, doers and leaders have propelled the industry toward vastly improved safety and social responsibility.The Prazen Living Legend of Mining Award, named for renowned mining artist Gary Prazen, will also be presented at the ceremony. This award recognizes an individual or organization for significant and sustained commitment to educating the public about the relationship of mining to our everyday lives through educational materials, programming, and outreach.2019 National Mining Hall of Fame inducteesFrank Calandra, Jr. has devoted more than 50 years to the mining industry and he is an icon in ground control technology for the mining, tunneling and civil construction industries.From the ground up, his passion, sweat equity and shrewd business acumen have grown Frank Calandra, Inc. (FCI) and Jennmar from a single plant in Pennsylvania to a world-class enterprise with 25 plants employing thousands globally. As evidenced by Calandra’s more than 20 patents on ground control devices (not to mention the additional 80 patents his companies hold), his innovation and commitment to safety have made underground mining safer and more efficient. In the late 1970s and early 1980s, Calandra was instrumental in upgrading American Society for Testing and Materials (ASTM) standards in roof control for both state and federal regulations. Through his work with industry associations such as the National Mining Association, National Coal Council and Center for Energy and Economic Development, among others, Calandra has contributed his time, expertise and financial support to ensure a balanced political and regulatory climate for mining. Calandra is an inductee of the West Virginia Coal Hall of Fame."

Aug 1, 2019

By Benjamin W. Haynes

Cement kiln dust (CKD) produced in the contiguous United States and Hawaii was characterized as part of the Bureau of Mines' program in minerals environmental technology. The mineralogical and chemical composition was determined for 113 CKD samples from 102 plants that normally send CKD waste to landfill. Characterization included the determination of 28 elements, 7 anion species, carbon dioxide, noncarbonate carbon, and chemically bound water. Mercury was determined in 15 samples. Interelement correlation coefficients were determined for 23 elements, 5 anions, CO2, noncarbonate carbon, and chemically bound water. To assess the hazardous waste potential of CKD, the U.S. Environmental Protection Agency Extraction Procedure (EP) toxicity test was performed on all 113 CKD samples. All but one sample were in compliance with the test; the noncomplying sample slightly exceeded the EP toxicity test criterion for lead.

Jan 1, 1982

By D Abbott

Mining in Western Australia places significant economic and environmental responsibility on Government and the mining industry. Groundwater abstraction is regulated by the Department of Water. The Department has recently issued a guideline for Pilbara mines, and this paper focuses on the Pilbara for its examples and studies. The guideline is intended to form the basis for developing a statewide policy, consistent with reporting and assessment policy.With rapid expansion of the mining industry between 2005 and 2008, the groundwater resources in the Pilbara region of the State are under increasing pressure. Significant new management and regulatory issues arising recently include: cumulative impact assessment; disposal of dewatering excess by discharge, sharing or reinjection; life-of-mine approvals and closure planning; closure water quality including metals concentration in pit lakes; and in situ leaching mining methods and their impacts on regional water resources (and change of State Government Policy with respect to uranium mining).

Jan 1, 2009