Search Documents

By A Tawadrous, B Wheeler, D S. Preece, S A. Silling

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Moving rock with explosives rather than mechanical equipment can improve mining efficiency. Such is the case with coalmine cast blasting. Controlling and directing rock movement through explosive deck delay timing can greatly improve ore recovery by segregating ore and waste. In both cases, understanding, predicting and controlling heave is an important element of successful blasting.Computer programs for predicting 2D blasting-induced heave have been used in mining for decades, helping to drive the innovation of new and more efficient mining methods, ie cast blasting. The past few years have seen the advent of 3D distinct element modelling of blast-induced heave. This is an important advancement because most blasting situations are three-dimensional in nature, especially when controlling the direction and intensity of rock movement through explosive deck delay timing.This paper documents the first full-scale blasting simulations in 3D with distinct element models that include hundreds of blastholes and in excess of a million particles, made possible with parallel processing. Surface mineral blasting is the focus of this study which treats the effect of blasthole delay timing on ore recovery. Ore waste and dilution resulting from typical row-on-row delay timing will be demonstrated. Also demonstrated will be the ore recovery possible with delay timing designs that significantly enhance ore/waste segregation. This type of high fidelity modelling and the use of electronic detonators makes possible the sculpting of rock blasting muck into separate piles of ore and waste.CITATION:Preece, D S, Tawadrous, A, Silling, S A and Wheeler, B, 2015. Modelling full-scale blast heave with three-dimensional distinct elements and parallel processing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 127–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By Z. A. Zhou

In Canadian oil sands processing, flotation is used to recover liberated bitumen droplets from oil sands slurries. Similar to conventional mineral flotation practice, a fundamental limitation of recovering bitumen from low grade oil sand ores is its slow and ineffective aeration of the liberated small bitumen droplets. Gas nucleation and cavitation could provide better mechanisms for accelerating bitumen-bubble attachment. A research program was undertaken to examine factors affecting spontaneous bubble nucleation on bitumen surfaces. The results demonstrate that surface hydrophobicity and existence of gas nuclei in process water play a critical role for bubble nucleation. While there are more bubbles nucleated on highly hydrophobic silanated glass surfaces than on moderately hydrophobic bitumen, bubble nucleation on clean hydrophilic glass surfaces is negligible. Heating process water up to 85 ~ 95oC (as used in commercial operation) or boiling tap water prior to gas nucleation tests is shown to remove sufficient amount of gas nuclei existing in the water, thereby drastically reducing the number of bubbles nucleated on bitumen. Enhancing gas nuclei formation in hot process water is identified as a promising strategy to improve bitumen-bubble attachment during oil sands conditioning, and hence to increase bitumen recovery from low grade ores.

Jan 1, 2014

Construction workers may be exposed to hazardous dust containing silica when working in enclosed cabs during construction activities. The National Institute for Occupational Safety and Health (NIOSH) found that equipment operator exposure could be reduced by retrofitting air pressurization and filtration systems on existing cabs, using sweeping compounds on soiled floors, and implementing a dust control program.

Jan 1, 2009

By L. W. Laage

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry for routine ventilation calculations and mine emergency planning. This paper describes recent work by the Bureau and MTU to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1993

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By Javad Sattarvand, Frimpong Kwaku Asare

The safe evacuation of miners during an emergency in the shortest amount of time is one of the most essential features of a mining operation. Despite advancements in mine evacuation research, the usage of mine vehicles during evacuation has not been considered. The majority of recent studies have been done on miners’ evacuation on foot. Mathematical formulations including Minimum Cost Network Flow (MCNF) models, Dijkstra's algorithm, Floyd-Warshall algorithm, and Ant Colony Optimization models have been used to solve mine evacuation problems. These models, which concentrate on determining the shortest escape routes during the evacuation, have been found to be computationally expensive and may not offer the best solutions in some cases. The goal of this paper is to incorporate light vehicles in the evacuation process using a mixed-integer programming approach. The methodology aims to minimize the total time required to evacuate the mine, ensuring minimal exposure of the miners to the adverse conditions that triggered the evacuation.

Jun 25, 2023

[ ]

Jan 1, 1997

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 318 petroleum refineries in the United States with a total daily crude throughput capacity of 8,632,390 barrels as of January 1, 1956. Compared with the previous year the total number of refineries declined 8 while the crude throughput capacity increased 211,760 barrels daily. Three refinery districts accounted for 90 percent of the crude-oil capacity increase, the California district 34 percent; the Texas Gulf Coast district, 31 percent; and the Indiana-Illinois-Kentucky district, 25 percent. Decreases in capacity during the year were reported for the East Coast, Appalachian #1, and the Arkansas-Louisiana Inland districts. The capacity of the average refinery to process crude oil increased during 1955 from 25.830 barrels daily to 27,145.

Jan 1, 1956

By William T. Boyd

Foreign mining publications describing successful hydraulic mining installations, and successful domestic hydraulic mining in a gilsonite bed, have prompted the Federal Bureau of Mines to conduct a literature survey of foreign publications to determine if the hydraulic mining method can be applied to domestic coal mining. Most foreign publications do not give detailed data about the water pressures, water capacities, and production and manpower requirements for successful hydraulic mining, However, they do provide enough general data on mining conditions, manpower, and equipment used to show that conditions in many bituminous coal deposits in the United States may be favorable for economical coal extraction, using high-pressure water jets. Therefore, the Bureau proposes to conduct a field investigation to determine the most appropriate natural conditions, water pressures, and equipment for successful hydraulic mining of coal beds in the United States with variable dip, thickness, and hardness. In the past, technical personnel reviewing foreign mining reports assumed that a steeply pitching coal bed was necessary for successful hydraulic mining. Although the structure of the coal bed may be a factor in gaining assistance from overburden pressures or help in an integrated hydraulic mining and transportation system, the coal is broken mainly by the action of high-pressure, water-penetrating cracks, fissures, or cleats; therefore, the slope of the coal bed is not necessarily a determining factor in hydraulic mining.

Jan 1, 1959

By Frederick J. Browne

Water, water everywhere, but not a drop (fit) to drink! Trite, but how often only too true? What is there met with in mining which, under various circumstances, may be said to be the most sought-for and highly-prized and also the most objectionable and most feared? Water! What visions that combination of five letters brings to all thoughtful minds? Up to near the end of the eighteenth century water was thought lo be an element but was then discovered to be the result of the combustion of two volumes of hydrogen with one volume of oxygen, and water so produced is chemically pure. Pure water is a clear and colourless liquid when seen under ordinary conditions, but appears bluish when seen through a long tube, and this same bluish tint may be observed in many lakes, especially those of glacial origin. A story often told describes a prospector in the desert who, failing to find water to replenish his canteen, suffers torture and death under fearful circumstances. Then again we may recall the flooding of mines, where water poured in so quickly that there was no opportunity of saving the unfortunate workmen. Instances might be multiplied without number showing that either the lack or excess of this essential fluid has taken heavy toll of human life. In all branches of mining and associated industries water must be dealt with to a larger extent, from an economic point of view, than any other substance, and very often the purity of the water is a matter of considerable importance.

Jan 1, 1925

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By Andrew Logan

Newcrest has a strong history of growth over the past 20 years, yielding value from previously marginal ore bodies. We have grown regionally in Asia Pacific through our operations in Australia, Indonesia and Papua New Guinea, and also established a beachhead in West Africa. The company has a reputation of realizing value from large, low-grade deposits adopting step change approaches. Newcrest is focused on an overall strategy of gold, low cost, long life and moderate growth. Capability step changes play a large delivery role. They transition from a business offline-to-online approach as opportunities mature. Newcrest believes in a) Knowing what ?good? looks like, b) An open innovation approach to actively working with others, c) The leap frogging leverage of making the ?old new again?, d)An adopt-adapt-develop methodology enabled by rapid prototyping/piloting, e) Getting our handsdirty with test work and plant analysis, and f) Staying focused on a few high business leverage areas. This paper describes Newcrest?s approach and our experiences in establishing renewed metallurgical processes, specifically aimed at increasing innovation adoption. Some of our step changes discussed include: 1) Early waste rejection to avoid high energy processing downstream, 2) Broader gold product channels to reduce site based processing needs, 3) Lower energy processing, and 4) Geo-Metallurgy approaches. Keywords: Newcrest, gold, step change, open innovation, adopt, adapt, develop, offline, online, prototyping, old new again, waste rejection, low energy, geo-metallurgy

Sep 1, 2012

By D. R. Nagaraj

Based on our finding that commercial copper chelating solvent extractants such as LIX65N® and LIX63® are excellent collectors for copper minerals, a detailed study was made using several water-soluble chelating agents belonging to the class of aromatic hydroxyoximes and having a gradual structural variation. A basic study of the system salicylaldoxime-tenorite was also carried out. Microflotation tests as a function of concentration of oxime, pH, addition of copper etc., using oxidic copper minerals such as chrysocolla and tenorite, and batch laboratory flotation tests using synthetic mixtures of quartz and oxidic copper minerals were carried out. The studies were aimed at an understanding of the collector function of the hydroxyoximes and of the general flotation behavior in these systems, in addition to studying the structural aspects of oximes vis-a-vis flotation. The results have demonstrated that all of the hydroxyoximes studied here have comparable collector property, and in all cases the oxime was found to be partitioned between the mineral surface and the copper in the bulk aqueous phase in the form of a bulk copper chelate. The occurrence of the latter could be accounted for by the formation in the bulk phase of a chelate between oxime and copper released from the mineral and/or by the detachment of the surface chelate. The role of surface and bulk chelates in flotation is discussed based on the results of partitioning of chelating agent into bulk and surface chelates in the system salicylaldoximetenorite. The effect of substitution of CH2 groups or benzene ring in the chelating agent molecule on its collector property is also discussed, in addition to the finding that only the anti-isomer has the ability to collect.

Jan 1, 1979

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By MOHAMMAD R. H. GORAKHKI, CHRISTOPHER BAREITHER, MANUEL APARICIO, IV JOSEPH SCALIA

Comingling filtered tailings and waste rock in a tailingsdominated mixture is a mine waste management strategy that has the potential to create geotechnically and geochemically stable landforms. Potentially acid-generating (PAG) waste rock can be sequestered within a filtered tailings matrix to enhance water retention and decrease hydraulic conductivity relative to a waste rock pile, potentially minimizing acid rock drainage (ARD). Enhanced water retention can reduce oxygen ingress limiting oxidation and resultant acid generation. Reduced hydraulic conductivity can slow inward percolation and outward drainage. In dry climates, the tailings matrix can hold precipitation near the ground surface accessible to evaporation and transpiration, thereby decreasing percolation. This paper presents an evaluation of comingled filtered tailings and waste rock in a tailings-dominated mixture (termed GeoWaste herein) and illustrates that ARD can be reduced under field conditions in a subtropical–highland climate.

By S. J. Kidder

The Mogollon mining district is in the southwestern part of New Mexico near the southern end of the Mogollon range, from which the district takes its name. The town of Mogollon is but 371/2 miles in an air line northeast of Clifton, Ariz. The air-line distance from Silver City is 521/2 miles and from Tyrone, 57 miles. Supplies are transported by motor truck from Silver City. The distance by road is 75 miles, half of which is an improved highway of modern construction. Transportation has always been a large item of expense in carrying on operations in the district. Valuable ore is said to have been discovered in the Mogollon Mountains as early as 1870 but the first regular prospecting was carried on in 1875, by James C. Cooney, a sergeant from Fort Bayard. His discovery of rich silver-copper ores in the region of Mineral Creek led to the establishment of the Camp of Cooney. Remote from any settlements where there was a semblance of law and order, and harassed by the Apaches, development was slow and nearly 10 years elapsed before the village of Mogollon was established on Silver Creek. Prospecting in this section of the district had disclosed the outcrops of several promising veins containing silver-gold ores. Among the early claims located were the Last Chance, Top and Confidence, on what has proved to be the most productive vcin in the district. To the end of 1922, the Last Chance and Top claims had produced approximately 600,000 tons of ore and nearly 200,000 tons had come from the Confidence group of claims. The total value of the ore produced from this vein alone has amounted to about $9,600,000 in silver and gold. The Fanney vein was developed later and during its most active period of production contributed more than half of the output of the district. Other important locations, though far less productive than the above, were the Maude S, Deep Down, the Deadwood and the Pacific.

Jan 1, 1925

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016