Search Documents

By M. R. Geer

The Bureau of Mines examined the washability data for 25 Appalachian coals requiring low-density washing to reduce sulfur content to 1 percent, using the distribution-curve method. The purpose was to estimate how closely theoretical sulfur values could be approached, what yields of washed coal could be expected, and the recovery efficiencies that might be achieved. Assuming that the run-of-mine coal would be crushed to 3/8 inch and cleaned in dense-medium cyclones, the calculations indicate that theoretical sulfur contents could be approached closely when cleaning at a specific gravity of separation as low as 1.30. With coals that have favorable specific gravity compositions the recovery efficiency anticipated for cleaning at 1.30 specific gravity is surprisingly high. Similar calculations for cleaning with concentrating tables at intermediate specific gravities indicated that theoretical sulfur contents at 1.50 specific gravity could be approached closely with some coals but not with others. The calculations suggest that operating a table at a specific gravity of separation much lower than about 1.50 probably would be unsatisfactory with most coals.

Jan 1, 1968

By D Morton, G Wallace

"Evolution Mining is the sole owner of the Mt Rawdon open cut operation, located 75 km south-west of Bundaberg in Queensland, Australia (Figure 1). It is a massive, volcanically hosted, low-grade gold deposit that exhibits excellent characteristics conducive to low cost mining and treatment.In 2014, Mt Rawdon began investigating initiatives to deliver higher mill throughputs without any significant capital expenditure or modifications to the existing processing plant. Various studies have shown throughput increases are possible by applying more blast energy, essentially by reducing feed size through blasting and leaving less work for the comminution circuits (Brent et al, 2013; Ziemski, 2011; Workman and Eloranta, 2003).Given that 53 per cent of energy used on a mine site is consumed by the comminution circuit, with only two per cent being consumed by drill and blast (Smith, 2013), it makes logical sense for a mining operation to align their drill and blast with their processing plant. The term commonly used when exploring this relationship is a ‘Mine to Mill’ program.Over nearly 12 months, various blasting options and Mine to Mill methodologies were tested at Mt Rawdon. Throughout the journey, it was abundantly clear that the Mine to Mill initiative is not as simple as making one technical or physical change and expecting an improvement. Rather, true sustainable improvements demand a paradigm shift across both the mining and processing cultures, where all departments are aligned and working towards the one outcome. This true overarching Mine to Mill mentality, enabled by Vistis™ 250 high energy bulk explosive, ultimately led to a sustained increase in throughput and profitability of the Mt Rawdon operation.Citation:Wallace, G and Morton, D, 2016. High Energy Bulk Explosives and Mine to Mill Focus – the Mt Rawdon Story, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 60–69 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Patricia R. Devine

This report expands an earlier study by Jack Faucett Associates (OFR #40-88) of the same title. Both reports are based upon an interindustry analysis from 1963 through 1982, during which time U.S. metals consumption and production did not keep pace with economic growth. The report discusses three sources of change: technological change, economic growth, and composition of final demand, as well as the relative importance of the individual components of final demand for metals. The results show investment and personal consumption to be the most metal-intensive components of final demand, and technological change to be the major cause of decline in consumption growth during the study period. Technology change is defined as alterations in production processes resulting in more or less consumption of metal per unit of output, often because of material substitutions and design changes. A trade analysis shows the significance of import growth, particularly indirect imports (metal contained in imported goods) as a factor contributing to the reduced growth rate of domestic metal production. The effect of import growth is partially offset by indirect export growth, suggesting that continued increase of all U.S. exports can have a strong effect in reducing the negative trade balance in metals.

Jan 1, 1988

By William J. Campbell

The columbite-tantalite mineral series was studied by various instrumental techniques to establish the relationship of density to composition. The samples used were carefully selected to obtain a mineralogical purity of at least 98 percent. Impurities were determined by optical microscopy, X-ray diffraction, and optical and X-ray spectroscopy. Each sample was analyzed by fluorescent X-ray spectroscopy for iron, manganese, columbium (niobium), and tantalum. The existence of a unique relationship in this isomorphous series permits a simple correlation of the intensity of a spectral line with the concentration of the analytical element.

Jan 1, 1955

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Stephen H. Stow

The relationships between the amount of light reflected off 21 samples of Florida phosphate and the chemical, composition of the samples were examined. It was found that the reflectivity of a rock is directly related to its chemical composition and that darker phosphates (less light reflectance) have relatively high amounts of iron, organic C and sulfate while lighter-colored rocks were rich in phosphorus, fluorine and aluminum. The use of reflectivity measurements could have economic applications in the phosphate rock industry: color specifications for rock shipments could he met, beneficiations by optical sorting could be performed and semi-quantitative analyses could be made rapidly and inexpensively.

Jan 1, 1971

By Leon H. Nelson

Several factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in, square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation. Pouring Temperature The temperature (or, more correctly, the amount of superheat above the liquidus-solidus) of the steel entering the ingot is, of course, one of the most important factors influencing segregation and solidification. Table 1 gives the average segregation of a number of heats of S.A.E. 1040 steel with normal pouring temperatures of 2775" to 2825" F. The table also gives some data on segregation in hot heats (pouring temperature 2840" to 2870" F.) and in cold heats with some skull (poured at 2725" to 2760" F.). The results in Table 1 are on steel ingots with 20-in. square cross section and 60 in. long to the hot top. The ingot weighs 7100 lb. and the hot top contains 14.3 per cent of the total ingot volume and 11.2 per cent of the total ingot weight. The results are from drillings after rolling the ingots to bloom size. Segregation results obtained on the bloom are probably not as great as they would be in the ingot itself, since heating the ingots for rolling can perhaps cause some migration of carbon from regions of high and low carbon to those of average carbon content.

Jan 1, 1937

By R. Pelton, Z. Dai, S. Yang

ABSTRACT Hydrophobic polystyrene nanoparticles were evaluated as potential flotation collectors for pentlandite. The flotation of hydrophilic glass beads demonstrated the nanoparticles’ ability to induce flotation. Deposition of nanoparticles on glass surfaces increased the contact angle and enhanced adhesion of the beads to air bubbles. High flotation recoveries were achieved when 5–10% of the bead surfaces were covered with nanoparticles. Surface functionalization—the addition of vinylimidazole to polystyrene nanoparticle surfaces—caused the nanoparticles to selectively deposit onto pentlandite surfaces in the presence of Mg-Si slimes. Ongoing work includes attempts to identify specific applications where nanoparticle collectors might be cost effective. _ KEYWORDS Flotation, Nanoparticle collector, Coverage

Jan 1, 2014

By J. E. Allen

The trend in refractory technology for the copper and nickel industries has been to higher quality raw materials and improved processing technology. These changes have been dictated by the changes in pyrometallurgical processes in these industries. For example the introduction of flash smelting, reaction type smelting and auxiliary slag cleaning furnaces havedemanded better refractories materials. Extensive field applications and improved laboratory testing procedures have helped make this transition possible. Changes in refractory technology, primarily in basic refractories, are followed from the late fifties to the present and into the future.

Jan 1, 1994

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By James Bennett, Jinichiro Nakano, Anna Nakano

Efficiency of the chemical looping combustion technology is adversely influenced by surface properties of oxygen carrier materials during oxidation–reduction process changes at elevated temperatures. In this work, natural hematite (Fe2O3) and alumina (Al2O3) supported Cu-spinel (CuFe2O4) oxygen carrier particles were isothermally exposed to redox gas cycles (air and 10 vol% CO–90 vol% Ar) at approximately 800 °C and studied using a high temperature confocal scanning laser microscope for real time alterations in surface morphology, roughness, and particle volume. 3D topological scans from each cyclic gas exposure indicated hematite particles exhibited noticeable volume expansion in reduction and shrinkage in oxidation, corresponding to respective phase transformations. Materials surface changes during the redox gas cycles are discussed.

Mar 1, 2017

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956

By Margaret R. Egan

The Bureau of Mines subjected three commercially available brands of transformer fluid to a series of combustion studies. The experiments were conducted in the intermediate-scale fire tunnel, which was designed to simulate environmental conditions in underground mines. The work was divided into three phases. In phase one, the brands were compared for gas production, smoke characteristics, and combustion yields. In phase two, the production constants of transformer fluids and other fuels were compared for the rate of formation of gas and smoke as a function of fire size. In phase three, several diameters of liquid-pool fires were compared in terms of fire size and burning rate. These transformer fluid measurements will be added to the existing coal and wood data that can be used as a basis of comparison for future studies of other mine combustibles. Further research into the combustion product emissions from combustible materials found in underground mines will lead to improved and realistic fire detection and suppression systems,

Jan 1, 1986

By J. E. Miller

Primary standard gas mixtures were developed for more accurate calibration of analytical instruments at the Bureau of Mines Helium Research Center and for calibration of analytical instruments used in the helium conservation program. A 10-kg-capacity balance is used to weigh a 4-kg metal cylinder filled to high pressure (1,800 psi maximum) with the component gases of the desired mixture. At 1,800 psi, a cylinder contains about 60 g of helium, or 420 g of nitrogen. An accuracy of ±0.05 mole-percent or better is claimed for each component in the mixtures.

Jan 1, 1965

By L. Yuan, J. Qin, J. Xie, Q. D. Qu, Y. P. Liang

"This paper presents key outcomes of a major Asia-Pacific Partnership project between the Commonwealth Scientific and Industrial Research Organisation and Huainan Mining Industry Group Co. Ltd. to develop and demonstrate advanced technologies at Pansan mine, Huainan, China. A comprehensive approach assessed fundamental strata and coal seam methane conditions during mining and optimized mining sequences and coal mine methane capture systems. The project demonstrated a practical approach and procedures for advanced coal and methane co-extraction systems, improved mining safety and efficiency, increased methane capture and use, and reduced fugitive methane emissions.RÉSUMÉ Le présent article donne les principaux résultats d’un grand projet de partenariat Asie- Pacifique entre le CSIRO (Commonwealth Scientific and Industrial Research Organisation) [Organisation de recherche scientifique et industrielle du Commonwealth australien] et le Huainan Mining Industry Group Co. Ltd.; ce projet cherche à développer et à démontrer des technologies avancées à la mine Pansan, à Huainan, en Chine. Une perspective globale a évalué les conditions fondamentales des strates et du méthane dans les couches de charbon durant l’exploitation et a optimisé les séquences d’extraction et les systèmes de captage du méthane dans les mines de charbon. Le projet a permis de démontrer une approche pratique et des procédures pour des systèmes avancés d’extraction conjointe du charbon et du méthane, pour améliorer la sécurité et l’efficacité minières, accroître le captage et l’utilisation du méthane et réduire les émissions fugitives de méthane."

Jan 1, 2015

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998

By A. Liem, R. L. Johnson, C. Sturgess, E. Kuzub

New challenges in mineral processing arise as high-grade ores become less available and the mining industry is forced to exploit lower grade ores. One of the challenges in beneficiating lower grade ores is the liberation of mineral particles while maintaining control over material management. Lower grade ores need fine grinding to free valuable minerals, but finely divided particles can cause severe problems, such as dustiness and flowability, in subsequent stages of material management. There are at least two approaches that can be taken to resolve this dilemma, both of which relate to particle size enlargement. First, the application of a dust suppressant can be used to control that aspect of material management. The optimal choice of dust suppressant agent depends on effectiveness and cost, both of which can be strongly influenced by the selection of application method. Second, agglomeration combining small particles into larger units-can reduce dust and improve the flow characteristics of the material at the same time. There are several mechanisms that can be employed to agglomerate mineral materials. Although agglomeration adds a new processing step, it is often cost effective. This paper describes these two approaches and their respective challenges, as they relate to a mined ore. We report on modified or newly developed procedures for characterizing mineral ores with respect to material management. On the same material, we use agglomeration processing to capture fines within larger particles and show how dustiness and other aspects of material handling are affected. We conclude by discussing their specific application in accordance with the mineral properties and processing needs.

Jan 1, 2004

By Randall Head

The drilling at the Taum Sauk Reservoir was a unique compilation of the latest technology and everyday common sense. This site is comprised of rhyolite, which is 30 times harder than limestone in comparison. Using some of the most state of the art drills, coupled with GPS guidance, angular drilling systems, and an ordinary piece of string, some of the most amazing drilling feats were accomplished. By constructing the new dam on top of a mountain that had been blasted once before nearly 50 years ago treacherous conditions for the drills and crew were a challenge. The drills had to be flown in by cranes to get to their locations, where they then drilled anywhere from 2.5 to 6 inch (6.4 to 15.2 cm) holes at angles up to 24.4 degrees. Custom drill bits were designed by the drilling crew to tackle feats such as drilling holes up to 120 feet (36.6 m) deep. A main challenge was the shape of the reservoir, as it is not in a straight line, but rather round, so no technological way was readily available to use to drill. Common sense came in and an ordinary piece of string was used to aide in drilling the hole. A revolutionary step was that our drill was used to core our own samples. By using our own equipment, we were able to complete this task for one-third of the cost of having a third party contractor obtain the core samples. On this unmatched jobsite, it has been established that technology has come a long way, but when all else fails, a piece of string will do just fine.

Jan 1, 2010

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

Ira B. Joralemon, one of the world's most noted mining geologists, died last year at the age of 91. "His long professional career," says Donald H. McLaughlin, chairman of the executive committee at Homestake Mining Co., "covered an epoch in the history of mining that was unique in its opportunities and achievements," adding that many mining companies (Bunker Hill, Bralorne Mining, Copper Range, Anaconda, Newmont, Phelps Dodge, Homestake, etc.) greatly benefited from Joralemon's experience and wisdom.

Jan 12, 1976