Search Documents

By Shabnam Sabah, Geoffrey Brooks

In oxygen steelmaking, splashing and droplet formation play a key role in the kinetics of the process. Though splashing has been studied by previous investigators, there is only limited understanding of how different cavity modes affect splashing. Therefore, a cold model study (at various lance heights and gas flow rates) has been carried out focusing on the issue of cavity modes and how it affects splashing phenomenon. Analysis using Fast Fourier Transform (FFT) was carried out on cavity oscillation that showed that frequency and amplitude of oscillation was highest in penetrating mode. Measurements of splashing over a range of conditions showed splashing greatly reduced when cavities went from splashing to penetrating mode. The results were validated and compared with plant data and previous model investigations.

Jan 1, 2014

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By M. W. Grabinsky, B. D. Thompson

ABSTRACT: Use of cemented paste backfill (CPB) offers economic and environmental advantages over other backfill methods. However, many operations have limited knowledge of how their CPB behaves in situ. Therefore, to avoid over-pressuring containment barricades, backfilling strategies necessarily tend to be conservative. In situ monitoring at Barrick Gold Corporation’s Williams Mine and Inmet Mining Corporation’s Cayeli Mine has been conducted and factors controlling barricade pressures are demonstrated, including rise rates, binder content, stope geometry, and tailings properties. The application of barricade pressure monitoring on a stope-by-stope basis can increase backfilling efficiency and, thus, reduce stope cycle times, while maintaining optimal safety.

Jan 1, 2011

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By C. Don Sullivan

Paraphrasing the poetic repetition of Gertrude Stein - "Research is research, is research, is research --- ad infinitum." But research takes many forms and involves many facets. Perhaps the most simple of definitions is that attributed to the late "Boss" Kettering of General Motors who in advising a young trainee said, "Research is an intelligent effort to satisfy the curiosity of the human mind." Reclamation research is complex and requires a diversity of scientific knowledge. The overall aim of land reclamation research is directed to finding practical ways to develop efficient methods to restore mined lands to productive use, compatible with use of adjacent lands, as soon after mining as possible; and, finding practical ways to reduce or prevent damage to surrounding resource areas, which may be affected by the mining process. Research in the field of mined land reclamation is not entirely new, although in some respects we are exploring new areas each day.

Jan 1, 1967

By GEORGE L. CHRISTIAN

T HE Tonopah Extension assay office is a two- story, concrete structure on a solid foundation of andesite, situated about 100 yd. from the company's mill, so that it will not be affected by the stamps or the tube-mills; also it will not be affected by under- ground blasting. On the second floor are the mine superintendent's office and drafting and blueprint rooms. On the ground floor are the assayer's office,' mixing room, furnace room, crusher room, chemical laboratory, parting room, store room, and change and shower room for the mine superintendent, assayers, and engineers. The crusher room is outside of the main building, and has four concrete walls, thus eliminating the jar of the crusher; it is so situated that the least possible amount of dust spreads through the main building. An 8 by 10-in. jaw crusher, which crushes to ¼ in., was made by a local foundry. Attached to the top is a small galvanized-iron hopper covered with a ¼ in. screen, on to which the sample is dumped. The fines-pass through the screen into the hopper, while the oversize is dumped into the crusher. The crushed sample and fines from the screen drop down to a set .of splits suspended from an iron rod below the crusher jaws. The small sample is caught below in a small pulp pan. The rejects drop from the splits through a 2-in. pipe on to a bucket conveyor, which dumps into a galvanized-iron hopper in an upper corner of the room. The rejects drop through a 2-in. pipe to a reject bin outside the build- ing. This bin is constructed high enough for a truck to be loaded from it by means of a chute door on the side.

Jan 1, 1921

In October, the Aluminum Company of America restarted the fourth of seven pot-lines at its Point Comfort, Tex. primary aluminum smelter. The price of primary aluminum ingot, as quoted by American Metal Market, was increased from a range of 60.5 to 63.0 cents per pound at the end of September to a range of 66.0 to 66.5 cents per pound at the end of October. BERYLLIUM On October 15, Brush Wellman, Inc., of Cleveland, one of two U.S. producers of primary beryllium products, announced a planned $6 million expansion of its extraction plant at Delta, Utah, increasing the plant?s capacity to extract beryllium from bertrandite ore by 25%. Another $5 million will be spent on two mine expansion programs in Jaub and Millard Counties, Utah. Other mineral claims and 1 eases he 1 d by The Anaconda Company will be taken over by Brush Wellman through lease or purchase. This expansion, when completed in 1981, will decrease U.S. dependence on imported beryl ore.

Jan 1, 1979

By O. J. Hollister

Jan 1, 1888

By G. Nazari

ERAMET, through its subsidiary COMILOG, have rights to a rich niobium and rare earth deposit inGabon. The Mabounié deposit, is located 50 kmfromthe town of Lambaréné, in a fairly remote location. ERAMET has been developing a process to recover value metals for several years, and approached Hatch Ltd. to design a sizeable Demonstration Plant to help them further optimize the process, and prove the flowsheet is technically viable. The process employs concentration techniques to recover an upgraded Nb/REE feed material for processing in the subsequent leach step. Rare earths and niobium are selectively leached, and subsequently precipitated. Following precipitation, rare earths undergo bulk separation and are purified to produce LRE and mixed MRE/HRE products, which will be further processed by Third Parties. This paper provides a high-level overview of the process, summarizes the motivation for a Demonstration Plant in the vicinity of the deposit, and discusses technical challenges faced during the flowsheet definition and design phase. Key challenges are focused on and summaries of the methodologies used to address each challenge, as well as the solutions to overcome the challenges, are discussed. The paper provides motivation for further process simplification and concludes with a project update.

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington, The investigation consisted of transit and topographic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds Were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and analyzed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing new sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest.

Jan 1, 1948

By K. Basaure, S. Palma, R. L. Castro

"Mud rushes are sudden inflows of fine wet ore within underground mines; they can harm people and equipment as well as cause production delays. Block and panel caving mines are prone to mud rushes in their production levels, with mud flowing from the drawpoints. Different mines have developed methods to control drawpoint conditions and thus perform safe ore extraction. The aim of this study is to develop a decision matrix and apply it to samples from drawpoints for the Diablo Regimiento mine, Codelco, El Teniente Division (Chile). The Abrams’s Cone was used to perform slump tests on mud samples and characterize their consistency by setting the saturation degree and packing. The unconfined strength for different saturation degrees and packing was then evaluated. The results show that conditions for fluid response in slump tests correspond to conditions for low strength in unconfined compression tests. We also found the water content value at which the flowing consistency changes from plastic to soft behaviour according to the slump test classification for each sample. This value varied between 12.2% and 16.9%, depending on the sample tested. Finally, a fluid security factor was defined in order to design an extraction pattern for the samples tested, based on the water content. We conclude that a very densely packed ore is not prone to flowing. The flow properties depend strongly on the specific properties of the ore tested, and consequently a specific criterion should be developed for different types of ore at a particular mine. The criterion developed for Diablo Regimiento ore provides critical water content values from 11% to 15%, depending on the ore type. IntroductionBlock/panel caving has the lowest cost and the highest production rates of all underground methods (Heslop, 2000; Hubert et al., 2000). Good management of the risks is important to ensure the security of personnel and infrastructure. Operational risks for the method include rockbursts, air blasts, and mud rushes (Hubert et al. 2000). A mud rush is defined as a sudden inflow of mud from a drawpoint or other underground opening into the mine (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005). Mud rushes can cause dilution, production delays, and damage to equipment as well as injuries and fatalities. The elements necessary for mud rushes are mud-forming material, disturbances, a discharge point, and water (Butcher, Joughin, and Stacey, 2000). All these elements are present in block/panel caving mines. Mud-forming material comes from ore milled by the caving process; water comes from underground and surface sources. Drawpoints in the production level are discharge points for the mud. Finally, several types of disturbance could trigger the mud rush phenomena: blasting, earthquakes, operation of equipment (Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012), arch collapse above drawbells (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Jakubec, Clayton, and Guest, 2012) and ore drawing (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012)."

Jan 1, 2017

U.S. producers for more than 5 months have priced 99.5 percent primary aluminum ingot at 486 per pound. Sales by independent dealers in this same period reportedly declined by 0.5$-2.5$ to 43.50- 44.56 per pound. CADMIUM: U.S. producer-published cadmium prices for the last 5 months have been at $3 per pound. Dealer quotes in the same period fell by almost 504 and ranged from $2.45 to $2.55 per pound.

Jan 1, 1977

By Leandro Seixas Bicalho, Wagner Cláudio da Silva, Kelly Laranjeira Nunes, Lívia Marques Faustino

Seeking to implement the Global Industry Standard on Tailings Management to improve the safety of their tailings facilities across the globe, mining companies are motivated to invest in new technologies to recover valuable minerals from tailings. One solution being evaluated is the use of magnetic separators to concentrate ultrafine tailings. However, this approach is energy intensive as it requires high magnetic fields to recover ultrafines, and usually results in low mass yields. Additives that modify pulp rheology and surface properties, or selective flocculate ultrafine particles, were tested to enhance the performance of magnetic separation. Promising results in laboratory scale testing different types of additives confirmed that it is possible to increase the mass yield, keeping the selectivity of this stage.

Feb 1, 2024

By S J. Schafrik, Z Agioutantis, E C. Jong, K Luxbacher

Real-time monitoring of mine operating parameters is available at most mines. However, access to these data for an individual operation is typically underutilised by mine managers and technical personnel. Such monitoring systems are typically designed to provide data streams and alarms to a responsible person, but they are not utilised to extract underlying trends or correlate different data groups. Furthermore, multiple monitoring systems are usually implemented at a given site without interconnection between vendors’ systems or connection to any central management, and mine personnel are only exposed to a minimal subset of such data. Thus, it is not easy to analyse and correlate individual data streams and generate information to enhance day-to-day operational decision-making and improve safety and efficiency.This paper addresses the primary challenges associated with centralising data management and effecting greater utilisation of the vast amount of collected data, while at the same time reducing the time and effort required to manage such large data sets. Furthermore, it presents the conceptual design of a database application that can organise, present and analyse data collected by multiple sensors in different environments. The database is designed to operate in a passive manner so that active mine data management systems are not impacted. An example is given where this database is used for managing atmospheric data collected at an underground coalmine operation in the US. These techniques have a universal application and can be incorporated in a wide range of mining and construction projects.CITATION:Agioutantis, Z, Schafrik, S J, Jong, E C, Luxbacher, K and Karmis, M, 2015. A platform for managing and analysing atmospheric data in underground coalmines, in Proceedings Third International Future Mining Conference, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Opportunities to monitor and control primary grinding mill performance are strongly sought after in the mineral processing industry. Currently, limited on-line information about mill charge motion and content is available to mill operations for control purposes, leading to periods of lower throughput, instability, variable product size and accelerated mill liner and lifter wear. In response to this need, CSIRO has developed an on-line surface vibration monitor for primary grinding mills which produces data that has been shown to provide new information about the mill charge in terms of toe and shoulder position, as well as potentially key features such as the overall charge level, the distribution between rock and balls in the mill, and the impact of the charge on the mill liners and lifters. This paper outlines the key features of the on-line monitor system, particularly those relating to data transmission, data analysis, and the design of the monitor and its independent power supply. It describes the coupling of single vibration sensor data from the CSIRO on-line monitor to the actual operating conditions of a SAG mill and how the vibration response and hence mill operating conditions vary as a function of time, including during mill equipment failures such as a broken discharge grate. Opportunities for improved mill control based on the data from the on-line monitor are also discussed, as well as the implications in terms of mill processing and maintenance performance. Recently a CSIRO monitor was also installed on a ROM ball mill and analysis of the vibration sensor data from this installation is currently underway. Preliminary findings from this installation will be presented along with comparisons of generic information, such as toe position (measurement precision and operation variability) and vibration signal (intensity, sensitivity and operation variability), between this type of primary grinding mill and AG/SAG mills.

Sep 1, 2012

By Benoît Pinier, Jason Furtney, Gustavo Sampaio Lopes, Jorge Valencia, Johan Hawinkel

This paper describes a numerical modeling study on the effect of airdecking on vibrations, fragmentation, and movement in mining-related rock blasting. Practice has shown that air gaps reduce blast vibrations and damage while maintaining the required fragmentation and movement, yielding similar blast outcomes with less explosive mass per hole. Given that the premise of “replacing explosives with air” for better blast results is counterintuitive, this paper aims to shed light on the physical mechanisms and processes occurring in a blast with airdecks. It is hypothesized that airdecks are effective and beneficial because they load the rock at pressures lower than what is required to crush the rock. In the airdeck, the explosive gasses directly fracture rock and avoid energy loss due to crushing. In essence, the airgap allows similar outcomes in fragmentation and throw with less total explosive product, as the lower pressure gasses in the airdeck are still effective at breaking and moving the rock. This is distinct from only having less explosive and more stemming, as the stemming reduces the pressure more than an airdeck at the same position. This study uses the blastFoam software (for modeling of single and multiphase flows) to accurately calculate the pressure history throughout a blasthole and air gap. The pressure and gas loading are coupled to numerical models of vibration, fragmentation, and blast movement. Using this modeling technique, a suite of blast scenarios for typical configurations in a range of commodities is assessed with and without airdecks. Rock blasting practitioners have a responsibility to protect communities, infrastructure, and heritage — demystifying airdecks through a better understanding of the physics provides another tool in the blasting engineering toolkit to serve this goal.

Jan 21, 2025

By J. Chretien

The ability to continuously monitor the air quality within a mine has become instrumental in becoming a low cost producer. The many considerations involved in monitoring air quality include sensor type, hardware placement, as well as data storage medium. BESTECH has had the opportunity to gain insight into these air quality monitoring considerations through deployments of NRG1-ECOTM, a minewide energy consumption optimization system. This paper explores the particular challenges overcome through these installations, and provides a set of guidelines for mines that want to maximize data capture while minimizing costs. It provides a view of additional benefits of air quality monitoring, such as ventilation control, reporting and trending.

Aug 1, 2013