Search Documents

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. The effects of feed matte grade, matte particle size, oxygen-to-matte mass ratio, oxygen content of the process gas and temperature on the particle oxidation rate, quality of conversion, particle size change and particle morphology were determined. The converting quality was highest (~68) with the 58% copper matte at 1100°C. At similar conditions, the 72% copper matte was more likely to produce copper oxides and leave unoxidized particles rather than directly produce sulfur dioxide at 1100°C, resulting in an average converting quality of 55. The quality of conversion was poorest for the 72% matte at 920°C (~45); the sulfur removal was extremely low even with a relatively high degree of oxidation. Fragmentation of the particles was significant in all cases with the 72% matte. A higher O2/matte .ratio and higher temperature, in general, resulted in increased fragmentation while oxygen enrichment had no significant effect. With the 58% matte, particle size was found to increase for the finest fractions rather than to decrease due to particle expansion.

Jan 1, 1998

By C. Hsu

Underground coal gasification (UCG) is becoming more popular as the reserves of good quality, mineable coal are starting to diminish, and yet the global energy demand from coal is still increasing. The purpose of this research project was to investigate cavity formation within a coal block due to the combustion reactions in the context of UCG. The cavity plays a pivotal role in the UCG process, as it is essentially the gasification reactor. Cavity formation in an in situ gasification process using the forward combustion linking method (FCL) had been investigated, and a laboratory model was created to simulate the process. The experiment was performed by drilling a U-shaped tunnel into a coal block, which was then combusted internally with air that was fed through an injection hole. A heating element (at approximately 500°C) was used to supply the required heat for combustion at the base of the injection well. The coal blocks were analysed using micro-focus X-ray tomography. The tomography results showed that the coal tended to crack along the bedding plane after a short duration of combustion, due to either the formation of clinker or the expansion of swelling vitrinite along the horizontal tunnel. The deposit was thicker at the base of the injection well compared to the base of the production well; this may have been caused by the turbulence of the air flow and the relatively high oxygen concentration at the base of the injection well. A comparison of the results with work by Daggupati et al. (2010) showed the same trend, despite the slightly different methodology applied.

Jan 1, 2014

By John H. Thompson

Recent studies ** at the Pittsburgh Experiment Station of the Bureau of Mines have revealed some interesting facts as to the probable behavior of steamed coke in the blast furnace . The literature on the chemistry of the blast furnace was tho roughly reviewed , and with this information in mind , the probable behavior of the coke sulphur in the blast furnace was deduced . Enough small - scale tests were conducted to furnish a check on most of the important deductions , and the conclusions derived therefrom accord with what is already known in regard to the forms of sulphur in coke , and fit in well with the general opinion concerning blast-furnace reactions .

Aug 1, 1923

By Richard P. Roberts

This paper will discuss the methods for the cooling of aluminum melting furnace? dross .and their impact on the environment. Also discussed will be a case history of an AROS Dross Processor installation, which is designed to maximize the recovery of metal content of the dross in a manner which is not only environmentally cleaner, but which also prepares the output in such a way as to facilitate downstream processes. Handling of the discharged material will be discussed in regards to the recycling of the preserved metal content and deposition of the unusable-materials.

Jan 1, 1992

By D. An, J. Withers

A nano-scale investigation has been carried out by applying an AFM (atomic force microscope) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it contacts the solutions of the collectors, suggesting that all these collectors can effectively adsorb on bastnaesite. Increasing temperature can help increase the adsorption of oleic acid on bastnaesite. FTIR (Fourier transform infrared) results also show that all these collectors adsorb strongly on bastnaesite with a strong absorbance spectra being detected, which confirms with the results obtained with AFM imaging analysis. In general, hydroxamic acid collector (HA and SHA) adsorbs on bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite. INTRODUCTION Rare earth metals, which are very important to modern industry, are generally extracted from numerous rare earth minerals. In practice, however, the actual extraction of rare earth is mainly from bastnaesite, monazite and xenotime. The Mountain Pass mine is one of the largest rare earth mine in the world, at which the main rare earth mineral is bastnaesite. In the past years, froth flotation has been applied to the beneficiation of Mountain Pass ore. In practice, the rare earth ore is usually crushed, milled and further separated from calcite, barite and other gangue minerals by froth flotation, in which the rare earth oxide-bearing minerals stick to aerated bubbles in the pulp and float to the surface, leaving the gangue at the bottom of the flotation cell and disposed of as tailings.(Bulatovic, 2010) In spite of the fact that froth flotation has been applied to treat the bastnaesite ore at the Mountain Pass mine, the rare earth oxide (REO) recovery is still low,(Anderson, 2015) especially compared to the one obtained with sulfide flotation. For example, the typical recovery obtained at the Mountain Pass mine was only about 70%. This may be due to the low selectivity of the collector (oleic acid). In addition, to enhance the flotation selectivity, the pulp in the mine circuit has to be heated up to 70 to 90°C and it involves a lot of energy consumption. Last but not the least, a lot of depressants have to be added to improve the selectivity of flotation process. Therefore, it is critical to re-examine the existing flotation process at the Mountain Pass mine and seek any chance of improvement. (Anderson, 2015)

Jan 1, 2019

By Diego Pacheco Wermuth

O presente trabalho apresenta os resultados do estudo e aproveitamento de cinzas leves da queima de carvão mineral em termelétrica, como reforço para o Compósito de Matriz Metálica de cobre. Foram estudados diferentes percentuais de cinzas leves como reforço para o cobre, sendo misturados estes pós através de misturador “duplo v”, compactando os pós em diferentes pressões e sinterizando os corpos de prova obtidos pela compactação. A amostra sinterizada que apresentou a maior dureza entre todos os corpos de prova sinterizados, atingindo 89 HV, foi utilizada como base para a formulação e obtenção de novos corpos de prova, que foram estudados sob condições de moagem dos pós por moinho de bolas e moagem de alta energia. A fabricação do compósito seguiu os padrões industriais do processo de Metalurgia do Pó, como a mistura e moagem dos pós, compactação dos pós e sinterização em atmosfera controlada. Foi realizado o estudo das propriedades mecânicas do compósito formado por cobre e cinzas leves, que comprovou o aumento da dureza para 122 HV. Este trabalho proporciona uma nova aplicação para as cinzas leves, utilizando estes resíduos de usinas termoelétricas como matéria prima para reforço mecânico na composição de peças à base de cobre na indústria metalúrgica.

Aug 17, 2017

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By AIME

Lewis E. Young, who will formally assume his duties as President of the AIME at the Annual Meeting in San Francisco in February 1949, was born in Topeka, Kansas, Oct. 1, 1878. Dr. Young received his engineering education at the Pennsylvania State College, where he received the degree of B.S. in Mining Engineering in 1900. In 1904 he received his E.M. degree from Iowa State College, and in 1915 a Ph.D. from the University of Illinois. In 1947, the University of Missouri conferred on Dr. Young honoris causa the degree of Doctor of Engineering. His active career began in the educational field as instructor at Iowa State College, and following that, as professor of mining at the Colorado School of Mines, 1903-1907. While he was at Golden he launched hi: career as consulting mining engineer for various Western companies. Leaving the Colorado School of Mines, Dr. Young returned to Missouri, serving the University of Missouri as director of the School of Mines and Metallurgy at Rolla, 1907-1914. Leaving Missouri he went to the University of Illinois as assistant professor of business organization, 1915-1918, during which period he wrote exhaustive treatises on mine subsidence and mine taxation, which won for him the degree of Ph.D. before mentioned.

Jan 1, 1949

By W. E. Robinson

Oil-shale kerogen was processed into oil and oil products before the first oil well was completed by Drake in 1859. However, because of economic and other advantages, natural petroleum has been the principal source of liquid fuels and lubricants since 1859 and is a convenient root of many [organic] chemicals in common use today. In recent years the difference has narrowed between the cost of producing liquid fuels from well petroleum and other sources. This narrowing of cost difference has resulted both from the increased cost of finding new sources of petroleum in the United States and the experimental demonstration of lowered costs for synthetic liquid fuels by the Federal Bureau of Mines and by industry. Available petroleum resources of this country are being reduced and eventually may be inadequate to meet the demand. Alternate means of assuring an adequate supply of liquid fuels for this country include the development of processes for utilizing other carbonaceous materials such as oil shale and coal.

Jan 1, 1960

By Stephen Njoloma, Ivan Hee, Ravi Jain, Mina Shinouda

"INTRODUCTION DC Water’s First Street Tunnel (FST) is comprised of a collaborative effort between DC Water, DC Water’s Project Consultants Organization (PCO) led by Greeley & Hansen and McMillen Jacobs Associates and the design-build team of Skanska, Jay Dee, and Parsons Brinckerhoff. The fast-track project includes elements that were designed by the PCO and released for construction by DC Water prior to Notice to Proceed (NTP) and elements designed by the Design-Builder from 30% to released for construction after NTP. This required effective communication and technical coordination for integrated engineering and efficient construction. The project, constructed in an urban residential neighborhood, included innovative construction methods such as multiple location ground freezing, utilizing a centralized freeze plant, to minimize community impact. The means and methods chosen for cast-in-place shaft linings, precast segmental tunnel lining, microtunneling, sequential excavation method (SEM) adits and near surface elements reflected the immediate and sensitive surroundings, which varied by construction staging area (CSA). Technical aspects of the project, relative to the evolution from pre-bid to construction documents, are discussed along with modified designs to suit means and methods. SCOPE OF WORK In 2012, four major storm events swept through the District of Columbia and hit the Northeast Boundary sewer shed particularly hard with the neighborhood experiencing severe flooding. The extreme nature of the flooding, the damage to private property, and the health risks associated with exposure to sewage led to a multi-agency response and community calls for answers and action. The Mayor assembled a Task Force to evaluate a range of potential actions to address combined sewer flooding including engineering, regulatory, code revision, and management improvements. The Northeast Boundary Neighborhood Protection Project was the outcome of the Mayor’s Task Force; it is a three-step infrastructure initiative designed to offload the undersized sections of the existing collection system that serves the Northeast Boundary drainage area by implementing the McMillan Stormwater Storage Project, First Street Tunnel Project and the future Northeast Boundary Tunnel Project. Until the Northeast Boundary Tunnel Project is completed, the First Street Tunnel Project will add 8 million gallons of combined temporary sewer storage in a new tunnel under First Street NW to relieve undersized sewers that traverse the Bloomingdale neighborhood."

Jan 1, 2016

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

The underground storage of LPG and other hydrocarbons is in current commercial use in Northern Hemisphere countries in Europe, Asia and the USA.Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, embarked on a worldwide feasibility investigation in 1989 to establish the viability of constructing an underground LPG storage facility in Sydney, Australia, the first of its kind in the country. Elgas recognised that with the limited 19 000 tonnes of storage capacity at Port Botany and the limitations imposed by use of small coastal ships (up to 10 000 tonnes capacity), a larger storage facility was required to utilise higher capacity ships from more remote sources such as the North West shelf and overseas. This would achieve security of supply in high demand periods and economies of scale. The underground option also provides improvements to safety and environmental standards.

Jan 1, 1999

By Christopher J. Bise

The potential of the coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints which have tended to limit the development of these reserves which can only be deep-mined are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short- term the industry has to incorporate presently available equipment which were not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment that are in use today and their possible application to thick-seam mining. The paper also addresses the various ground control and safety considerations that are unique to thick-seam extraction.

Jan 1, 1981

By A. O. Dufresne

Introductory At the Annual Meeting of the Institute, held two years ago, I had the privilege of presenting a paper on Recent Mineral Discoveries in Western Quebec. In it were pointed out the areas favourable for prospecting in that section of Quebec adjoining the mining camps of northern Ontario; the discoveries that ?had been made were recorded; and some of the developments up to that date were reviewed. Since then, two full years have elapsed, during which a considerable amount of serious work has been performed with such results that western Quebec has today six properties about ready to mine commercial ores of gold, copper, and zinc. These results have been brought about after large sums of money had been invested to bring the district to a producing stage. A smelter has been built, and is already producing copper; two railways have extended their lines into Rouyn; and the Provincial Government has shown faith in the future of the district and has spent large sums of money in the building of highways and for other public works. The purpose of the present paper is to review the developments of the last two years, and the work that has been performed in various spheres of activity in that section on western Quebec covering the county of Abitibi and the northern part of the county of Temiscamingue.

Jan 1, 1928

By M. Werner

Mining in the Coeur d'Alene Mining District has been going on for over 100 years with a long- term continuation very likely. Mining is presently carried out at depths below the -5000' horizon. As mining continues at ever increasing depths, higher in-situ rock stresses and subsequent rock deformation is encountered making mining costly and hazardous. To provide access for men and materials in such areas, a wooden raise preparation structure is typically built. Although these structures provide adequate support and access, they have proved to be very costly to construct and maintain.

Jan 1, 1986

Both innovation and excellence are desirable attributes of education, as they are also markers in the progression of the human race, but how attainable are they? The interaction of minerals and humanity provides a special insight into the development of both criteria, from the discovery that chert cuts, through the Bronze Age and the first use of metal alloys for implements, to using coal, oil and uranium as sources of fuel. However, there have been many hiccups along the way, where excellence in one respect has meant disaster in another. Examples are in the exploitation of asbestos, and in traditionally poor work practices in mining, both contributing to the widespread public belief that minerals and mining are ecologically undesirable. Yet is this perception based on the unrealistic expectation of innovation and excellence being simultaneous qualities of any given process? Common sense born of experience indicates that the journey from one, to the other, is usually a long and often tedious process, with much trial and error before excellence is attained. In our time, the partnership between academia and industry is the usual pathway to achieve it. Even so, we should take care that innovation does not become overwhelmed by the pursuit of excellence: as history clearly demonstrates, humanity depends upon both.

Jan 1, 2004

By T. I. Weston

This is one of a series of papers being prepared for and published by the United States Bureau of Mines, describing mining and milling methods and costs at crushed-stone plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized' tat publication of total production costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. However, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no mis-understanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance-of F. W. Horton, mining engineer, United States Bureau of Mines, in the preparation of this paper.

Jan 1, 1933

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By Joseph O. Cook

I know this is, at best, a frustrating period for the coal mining industry. About 20,000 miners have been laid off, mostly in the Appalachian and mid-western areas, and several mines are working less than 5 days a week; however, the industry is experiencing modern growth and, at least, there is the potential for future growth. The coal industry is probably only operating at about 80 percent of its present capacity, and it is certainly capable of helping this country solve its energy problems. Growth, as a rule, does not come easy, and growth in the coal industry is no exception to this rule. Many formidable challenges have to be overcome. As we all know, mining relies very heavily on the earth sciences, which have advanced significantly in the past few years, but we are always working in a changing environment which in most cases is a hostile environment. Large quantities of material are quickly extracted and rapidly moved in, generally speaking, a very confined area. The very nature of the mining business directly and constantly impacts our environment during this period in which the Nation and the world has become increasingly smaller and more concerned about protecting our environment. In addition, growth brings about an expanding work force which is increasingly younger and less experienced.

Jan 1, 1980