Search Documents

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By Donald L. Johnson

REVIEWS on the applications of optical ellipsometry to the study of polycrystalline metal surfaces and oxidation-corrosion processes have been presented by Kruger and Hayfield, and white.' In view of the ability of this method to measure differences in film thicknesses to below 10A, ellipsometry was used to study nitrogen chromium surface reactions during the early stages of growth. Chromium specimens in the form of a vapor-deposited film on glass substrate were exposed to purified nitrogen for selected time increments at 700°F. This temperature was selected because it gave the best combination of exposure time and thickness change. Ellipsometer readings were taken immediately after exposure to determine polarizer and analyzer angles using monochromatic light at 5000A.2 After each set of readings was obtained, the specimens were exposed for an additional increment of time in nitrogen and a new set of readings taken. Film thickness was computed from LUCy's3 equation for nonabsorbing thin films. In Lucy's derivation, two equations for computing thickness were obtained. Peterson and Bashara4 have discussed the validity for using one of these equations when an independent value of the refractive index is used. The film was assumed to be Cr2N (Ref. 5) and was determined to be optically isotropic. Optical isotropy was determined by rotating the films about the surface normal and noting that the azimuth and phase difference did not change. Since Cr2N is reported to be hexagonal, it is assumed that optical isotropy results from randomly oriented grains of very small size. The thickness was computed using refractive indexes varying from 1.6 to 2.0. The maximum variation in computed thickness over this range for a given exposure was 20 pct. The data reported are based on a refractive index of 1.8. Reference readings on the metal surface were taken just prior to nitrogen exposure. No attempt was made to deoxidize or denitride the metal surface after vapor deposition, although specimens were observed to gain approximately 2A per day in air at room temperature. Twelve experimental exposures were made on a single sample over a total accumulative time of 132 min. Additional experiments over longer time intervals were made to determine the effect of heat up and cool down during and after exposure. As a result of these experiments, the thickness computed for each exposure was increased by 4A. Time profiles based on the linear law are similar to the oxidation profiles for many metals.' The rate of accumulation of the nitride film is rapid at first and slows down as the film thickness increases. The parabolic law x2 =k1t +k2 [11 gives a straight line in Fig. 1; therefore, it is concluded that the kinetic behavior is parabolic. Sey-bolt and Haman5 reported similar results for CrlN on chromium at 1000°C although the order of the thickness was much greater (10-3 cm). Analysis of thickness data based on other values of refractive index shows that the curves are shifted vertically but retain the same shape. According to Mott,7 it is expected that for thin films k2 is zero in Eq. [I]. Since the plot in Fig. 1 is linear through the origin, k2 is zero and the parabolic nature of the film growth is further indicated. The parabolic rate constant, calculated from the slope in Fig. 1, is 4.4 x 10-16 sq cm per sec. The corresponding work (+) required to bring an electron from the metal into the oxide is estimated to be 1.5 ev.7 The author thanks professor N. M. Bashara and D. W. Peterson, Electrical Materials Laboratory, University of Nebraska, for making the ellipsometer available and providing technical assistance. The Electrical Materials Laboratory is supported by the office of Naval Research, NONR 3718 (01). This work was partially supported by the Engineering Experiment Station and the Mechanical Engineering Department, University of Nebraska.

Jan 1, 1967

By Norbert Steiner

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O, instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O, with SO2 yielding H2SO4 up to 70% strength, depending on off-gas temperature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentration, residual SO2 concentrations of less than 20 mg/Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O, process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

By Firat Atalay

Estimating the spatial distribution of ore grade is one of the most critical steps to proceed with an investment decision on a deposit. Kriging is the most widely used method to estimate the ore grade, but alternative techniques are being developed. Machine learning algorithms can be used as alternative methods to classical kriging. In this paper, the iron (Fe) grade of a deposit is estimated with the XGBoost algorithm, and the results are compared with kriging estimation results. For the estimations, samples collected from drillholes were used. Due to the different natures of the estimation methods, different steps were taken to perform the estimations. The results show that XGBoost produced higher-range estimates, which is a desired result in ore grade estimation, and the minimum and maximum of the estimates were lower and higher than the kriging estimates, respectively. However, like kriging, the estimation results were smoother than composites, and the variance of the XGBoost estimates was lower than the variance of composites. This means that even though estimation with XGBoost mitigates the smoothing effect, the estimation results suffer from smoothing like kriging.

Dec 1, 2024

By Ian Masters

Rotary furnaces are widely used throughout the metals industry. These furnaces vary in size and geometry, but are fundamentally the same from a thermodynamic viewpoint. A generic method is proposed that can be used to model all furnaces of this type, provided that the correct material and process parameters are known. Various approaches have been attempted in the past based on a continuum (FEA or CFD) approach. However, the complex fluidlsolid interactions present in a rotary vessel are not easily solved using these methods, which work best where the material boundaries are well defined. In this paper a lumped parameter model is proposed. Variations within a section of the model are ignored, but to ensure thermodynamic correctness, the heat transfer between sections is carefully considered. For example, it is reasonable to assume that the whole of the melt pool is at the same temperature, due to rotary mixing. This may then be modeled with a single set of parameters, and the detail is contained in obtaining the correct heat transfer mechanisms from the rest of the furnace.

Jan 1, 2002

By S. H. Morar

Froth stability is widely recognized as a key driver of flotation selectivity. It is well known that froth stability is affected by the type and quantity of surface active reagents present (frothers), and the concentration and hydrophobicity of solid particles present. While some studies have been performed on the effect of frothers on froth stability in three-phase systems and the hydrophobicity of particles present, very little work has been performed on the effect of solids loading on froth stability. This may be due to insufficiently robust measurement techniques. This paper investigates the use of a new machine vision measurement to measure solids loading, and the relationship between this measurement, bubble size, and bubble burst rate on the froth surface. Keywords: froth flotation, machine vision, solids loading

Sep 1, 2012

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

By J Burgess, G Scanlan

In 1993 after over 110 years of mining operations, production ceased at the Broken Hill North Mine. Following the cessation of operations a rehabilitation program was developed to satisfy the requirements of the various government departments. This program has been implemented progressively since mine closure. The paper will discuss: primary aims and objectives of the rehabilitation program, implementation of the program, rationale behind rehabilitation objectives, and problems encountered in implementation of the program. To-date the primary rehabilitation of the mine has involved the capping of redundant tailing dams with inert waste rock to prevent the contamination of the receiving environment. A Water Management Plan has been developed to contain all run-off from the mine area in an extreme storm event. A cultural heritage assessment of the leases has been undertaken to ensure the rehabilitation is consistent with the historical significance of the site and community expectations. All redundant material from the mine has been sold in a æno reserveÆ auction and the workshop area has been relocated to the Southern operations. At present the only active areas on the mine are a maintenance area for equipment for the Potosi open pit, and a primary crusher for Potosi ore which is railed to the Southern operations for further processing. Upon completion of the rehabilitation program, Pasminco Broken Hill Mine intends to relinquish the mining leases to the Department of Mineral Resources.

Jan 1, 1998

By A. Ducastel, S. Connemann, A. Stark, F. Bouillot, C. Fricke-Begemann, LSA, H. Knapp, L. Horckmans

"Refractory materials are essential for all high-temperature applications in industry. Depending on the position in the furnace and specific process requirements, refractories are produced from several raw materials, such as dolomite, magnesite, bauxite, graphite or chromite. Most of these raw materials are not rare but strict quality requirements limit the producers of refractories to only a few deposits in the world. Thus, raw material supply is a critical factor for the production of refractories and accounts for 40-50 % of the total costs of refractories.A possible way to lower dependency on raw material supply is recycling of spent refractories. Main challenge in recycling is the separation of different brick types from each other and the removal of impurities, such as steel or slag. The European FP7 project REFRASORT aims to apply sensor-based sorting for separation of spent refractories. Sensor-based sorting is known from food industry, recycling and mineral processing and has proven its reliability. Nevertheless, some adjustments are necessary compared to applications in mineral processing because of other sensor-types and a higher number of products in one sorting step. This paper presents the results of feasibility tests for sensor-based sorting of refractories with near infrared spectroscopy and laser-induced breakdown spectroscopy (LIBS). Both sensors showed the potential to identify different brick types but the most promising results were obtained using LIBS technology. INTRODUCTIONRefractories are solid, ceramic products, which can sustain temperatures of more than 1500°C, without losing their stability or shape. Bricks of refractories have to withstand corrosion in contact with liquid steel or slag. Various high temperature applications, such as the production of glass, steel, copper or cement, require high quality refractories. The quality requirements of refractory bricks are strict, because small impurities can lower the thermal strength significantly."

Jan 1, 2016

By O. C. Blade

Studies on more efficient utilization of petroleum have been made for 50 years by the Bureau of Mines. As part of this work, the Bureau has analyzed thousands of samples of crude oil by its standardized routine method, and many of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published from 1921 to 1959, and brings up to date the information in Information Circular 7470 3 and in the appendix of Bulletin 490.4 The routine method of analysis and the equipment originally were described in a report by Dean and associates. 5 This report has long been out of print, but Bulletin 490, bringing the procedure and its modifications to date, was published in 1951. 6 Briefly, the procedure consists of testing, by standard methods, small samples of a crude oil for gravity, sulfur, color, viscosity, pour point, and (more recently) nitrogen; and, by a standardized procedure, distilling a portion of the crude oil and determining certain properties on the separated fractions and residuum. Careful records are made during the procedure, and the distillation data obtained are used to compute the approximate amounts of products present in the sample--such as percentages of gasoline, kerosine, gas oil, and lubricants. The principal data and results are recorded on a standard analytical report form. An analysis of a sample of crude oil from a recently developed field is shown in table 1. Compilations of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses often are included in connection with other studies, such as engineering field reports.

Jan 1, 1959

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader&apos;s orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature&apos;s effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By Prosser A. P

The conditions under which vanadium is rendered insoluble by silica in the alkali-roast process have been investigated starting with both slag and reagent-grade materials. The inert phase is a glass formed slowlyfrom soluble NaV03 produced at lower temperatures. It contains approximately 30 per cent V in a partly reduced state; iron is not a principal component. Some of the vanadium in the inert phase is slowly returned to a soluble form by heating in an oxidizing atmosphere below the temperature at which the glass is formed (750&#176;C). As the reaction leading to the required, soluble form of vanadium is also slow between 600 and 750&#176; optimization and control of the temperature profile and atmosphere in the furnace, and the residence time of the solids, are necessary to ensure high vanadium extraction during subsequent leaching.

Jan 1, 1976

By Jan Svoboda, Toyohisa Fujita

The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation in magnetic separation are identified, advantages of this technology in comparison to other physical methods of material manipulation are discussed and reasons for its failure to live up to its potential and expectations are indicated. Derailers that were responsible for the implementation failures are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.

Jan 1, 2003

By P. Fossi

This report describes a pilot-scale study of a hydrometallurgical process to treat high-grade nickel matte or a nickel-cobalt sulphide precipitate to produce high-purity electrolytic nickel. The first step of the process is the oxidative leaching of the nickel-bearing material by nitric acid; the nitrous gases generated during leaching are reconverted to nitric acid. The crude nickel sulphate nitrate solution is purified and is then subjected to a denitrification step. Nitrate separation is effected either by the crystallization of nickel sulphate or by precipitation of basic nickel carbonate. The electrolyte is prepared from the nitrate-free material and nickel is then recovered by electrolysis of the sulphate solution using insoluble anodes. Some technical and economic problems encountered with this processing route are discussed and the method is compared to the "all-chloride" process developed by Société Le Nickel.

Jan 1, 1977

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goi&#225;s and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m &#215; 3.8 m to 2.0 m &#215; 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m &#215; 3.8 m to 2.6 m &#215; 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

By J. M. Rios

This paper exposes the reasons that led the Empresa Nacional Minera del Sahara, S.A. (ENMINSA) to the selection of a conveyor belt system for the transport of phosphate rock over a distance of 100 kilometers. ENMINSA was created in 1962, with the main objetive of the exploitation of phosphate rock deposits in the Spanish province of Sahara, in North West Africa. Poor grade outcrops were known previously. A detailed geological research carried over the province led ENMINSA to the discovery of deposits not exposed, and of much higher grade. The sector known as Bu-Craa was chosen as the most promising, and was explored by means of drill holing and shafting. The important amount of information obtained permitted a detailed evaluation of the capacity and grade of the rich ore contained in the Bu-Craa area. Simultaneously with the systematic reconnaissance of the Bu-Craa deposits, ENMINSA developped the study of the technical and economical problems required for the beneficiation of the rock, which comprised five main groups of projects: rock exploitation; beneficiation plant; rock transport from the mine site to the Atlantic coast; storage, handling and loading facilities by the sea- side, and power plant. Once determined the location of the marine loading facilities, which to date are in an advanced stage of construction (figs. 1 and 2), the studies conductive to the selection of the best transport system from the mine to the ocean, along 100 kms. distance were undertaken.

Jan 1, 1968

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019