Search Documents

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

Jan 1, 2005

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Paul Meadows

The Buckrange reservoir, Stephens field, Ark., is approaching the economic limit of production under present operating conditions. Over 100 million barrels of oil remaining in the reservoir will not be recovered by primary producing methods. The Bureau of Mines, in cooperation with the Arkansas Oil and Gas Com-mission, made the petroleum-engineering study presented in this report to aid operators in evaluating secondary-recovery possibilities in the reservoir and in planning secondary-recovery programs if their initiation is decided. The Stephens field, in Columbia, Nevada, and Ouachita Counties, Ark., is about 12 miles northeast of Magnolia, Ark., and 15 miles west of the Smackover field. Surface elevations in the area average about 240 feet above sea level.

Jan 1, 1956

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By A. A. el-Geassy, A. A. el-Tawil, Hesham M. Ahmed, Bo Bjorkman

The Iron and steel industry is one of the most intensive energy consuming processes. The majority of iron making processes is now directed towards the uses of fossil-based energy sources like coke, coal and oil. Recently, emphasis has been paid to replace part of fossil- based energy sources with renewable biomass-derived reducing agents. In the present work, the possibility of the effective use of woody biomass in carbon-iron oxide composites was investigated. Wood powder was carbonized in N2 atmosphere at 300 up to 450oC. The carbon content in the produced bio-char increased with temperature. The porosity of the char arises from maintaining the cellular structure inherent in wood biomass increases with temperature. The reduction behavior of four iron oxide-bio char composites having different fixed carbon content were carried out non-isothermally up to 1200oC in Ar atmosphere using thermogravimetric anlyser (TGA). Quadruple mass spectroscopy (QMS) was also adopted to measure the CO, CO2 concentrations in the off gases resulted during reduction process. The effect of volatile matter on the reduction of iron oxide was intensively studied. The different phases developed in the reduced product were identified by X-ray diffraction (XRD). The reduction of composites was found to proceed in a stepwise manner (Fe2O3?Fe3O4?FexO?Fe).

Jan 1, 2015

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

By D. M. Ziebarth

"Normal sequence of operations to develop a new underground mine is: construct and outfit headframe for shaft sinking, sink shaft, construct and outfit shaft sump, develop shaft station and shaft bottom steel. In an effort to reduce the overall project schedule, an innovative plan was developed to install service shaft steel below station level, prior to the completion of the shaft sinking effort. To better evaluate the construction of this substantial steel tower, a preliminary constructability evaluation was conducted, including the best method of supporting the main tower; from the bottom, middle or top of the tower. The design criteria and plan involved: •,Develop access from existing service shaft, 25 km underground •,Use of materials to maximize strength while minimizing corrosion exposure •,Estimating the location of the shaft centerline •,Over excavating the station and shaft below station to allow future shaft steel repositioning •,Designing the tower steel for modular installation •,Incorporate commissioning considerations, such as suspension of the cheese weights during steel installation •,Provision for covered stair access to shaft bottom •,Enclosed shaft envelope with open panels to allow visibility and ventilation The design approach was innovative and this paper will describe the design principles and challenges encountered while providing insight into the solutions developed and implemented; especially the modular construction and installation methodology. INTRODUCTION In an effort to expand the mining operations, a plan was developed to construct a new service shaft closer to the new mine workings and convert the existing service shaft to a production shaft at the Potash Corporation of Saskatchewan Inc. (PCS now Nutrien) Rocanville Potash mine in southeast Saskatchewan. The new service shaft required a multi roped friction hoist operating a cage / counterweight, rope guided conveyances to support the operational requirements. The service shaft is an integral part of the mining infrastructure as it provides access to the underground workings, transport personnel and materials underground for operation and maintenance of the mine. The shaft also allows for services required for safe operation of the underground mine, power supply, controls, communication, dewatering and fresh water supply."

Jan 1, 2019

By Mikael Calando, Thomas Joussellin

"San Francisco's rapid growth has caused the city to plan for the Transbay Transit Center Project, a visionary transportation and housing project, that will transform downtown San Francisco and the San Francisco Bay Area’s regional transportation system by creating a “Grand Central Station of the West” in the heart of a new transit-friendly neighborhood that will be home to more than 20 new towers rising a high a 1,070 ft. This paper describes the specificities of using advanced diaphragm wall technology, tooling, equipment and installation practices for deep foundation and permanent underground structures. In particular, this paper will emphasize on the urban constraints, geotechnical conditions, and the novel approaches adopted for the construction challenges of the Transbay Transit Center’s Load Bearing Elements, or Barrette PilesPaperThe Transbay Transit Center Project consists of the construction of a new multimodal, five-story Transit Center located in the South of Market neighborhood near the Financial District in San Francisco. The future Transit Center will incorporate nearly 83,000 square feet of retail, a 5.4-acre rooftop park, an extensive public arts program and bus ramps that will connect the Transit Center to a new off-site bus storage facility and the San Francisco–Oakland Bay Bridge. The new facility will accommodate more than 100,000 passengers each weekday and up to 45 million per year. Additionally, the new Transbay Transit Center will replace the since-demolished San Francisco Transbay Terminal, and nearly 20 towers, such as Salesforce Tower, will take advantage of the height increases allowed through the Transit Center District Plan.The approximately $4.5 billion project features a new five-story structure (including two underground stories) and new bus ramps which include a cable-stay bridge. The deep foundations for the pylon of the bridge (Pylon 9) consist of two each 21 ft x 5 ft barrettes (also called Load Bearing Elements in the US) extending more than 180 feet below grade and 10 feet into the bedrock. The barrettes were chosen because of the combination of high loads, significant depth and small footprint. The barrettes are installed using the Diaphragm Wall technology. Nicholson Construction was contracted by Shimmick Construction to install the cable-stay bridge’s foundation elements."

Jan 1, 2016

By Henk L. C. Meuzelaar

Most of us are aware of the relationship between the golden-yellow resin spots on Upper Cretaceous Wasatch Plateau coals and fossil tree resins (?amber?). Nevertheless, confusion remains about the exact chemical composition and structure of commercial coal resin preparations as well as their observed heterogeneity. In order to arrive at a more detailed chemical description we need to distinguish between micropetrographic, organic geochemical and process technological definitions of coal resins, which may include substantial quantities of constituents unrelated to fossil tree resins. New information on composition and origin obtained by Curie-point pyrolysis/evaporation in combination with isobutane chemical ionization mass spectrometry, as presented in this paper, points to the presence of four more or less distinct resin components: (1) a sesquiterpenoid polymer; (2) sesqui-and triterpenoid monomers and dimers; (3) a suite of triterpenoid alcohols, ketones and acids; and (4) a series of increasingly aromatized hydrocarbons with naphthalene and picene type skeletons. Moreover, a strong similarity is found between the composition of recent Dammar resin and fossil Wasatch Plateau coal resins. Some of the technological implications of these findings and the consequent need for a more precise chemical definition and nomenclature are discussed.

Jan 1, 1990

By D. Mjonono, S. T. L. Harrison, N. Maliela, A. Kotsiopoulos

The improvement of coal waste management practices, through the co-disposal of waste rock with sulphur-lean fine waste tailings (<1 mm in size), can potentially mitigate acid rock drainage (ARD). On exposure to natural oxidants, the sulphide compounds present in mine discards generate acidity, creating a cyclical oxidation process intensified by iron and sulphur oxidising microorganisms. To inhibit the emergence of ARD, a stable mine dump may be constructed that is structurally stable and incompressible through the mixing of complementary waste fractions that reduce voids and access to acid generating surfaces. However, large voids manifest as scale increases, due to decreased particle interlock, enabling the unrestricted access of oxidants leading to the early onset of ARD. To avoid this phenomenon, enhanced packing approaches based on geochemical and geotechnical characterisation tests were employed to improve bed stability. These were assessed for long-term prevention using aggressive oxidative conditions typical of heap leaching applications. Favourable results were obtained for both blended and multi-layered systems. However, long-term success was most notable in beds with alternating layers of waste rock and fine waste tailings with co-mingled systems being more susceptible to failure. Deconstructed co-disposed beds provided valuable insight into post-leach structural transformations. Results indicated that relative changes in initial coarse discards to fine waste ratios were most notable in blended systems. Mass fractions of the comparatively more mobile fine wastes increased axially down these test columns that ultimately resulted in increased contact of oxidants with the acid generating waste discards. Conversely, more consistent ratios were observed in multi-layered configurations. In these systems, near impervious hardpans were created by the moisture retaining fine tailings, forming stable structures with neutralising barriers sustained at each alternating layer. Consistent with post-leach geotechnical characteristics, static acid-base accounting tests showed that the uppermost sections of blended systems were more susceptible to oxidation due to structural failure with fine particles migration, while the more stable multi-layered configuration evenly maintained neutralising capacity. Keywords: Acid rock drainage (ARD), bed structure, mobility of fine particles

Jan 1, 2020

By J. W. van der Merwe, A. S. Bolokang, M. J. Phasha, V. J. Matjeke, C. Moopanar

"Excessive wear rates on railway wheels can result in rolling-stock derailments. If wear is detected early the possible derailments can be prevented by prematurely replacing wheelsets, although the inventory cost and maintenance downtime remain a challenge. In the current study, wheels were introduced and monitored in-service for two years to investigate the cause of excessive wear rates. The wear rates and stresses were calculated for the wheels suitable for a maximum load of 26 t per axle. Microstructural and mechanical properties were analysed. As expected, the general microstructure of all the wheels tested was pearlitic. Although all the wheels complied with the tensile strength requirements, stress calculations confirmed material distortion on excessively worn wheels whereas trial wheels revealed yield strength exceeding the yield criterion. High wear rates observed on the wheels were a result of low yield strength relative to the load per axle. The typical wear mechanism found was due to a combination of rolling contact fatigue and abrasive brake wear. Despite compliance of the wheels with existing requirements regarding material and mechanical properties (hardness, ultimate tensile strength), it is recommended that the yield strength must also be taken into consideration as a critical parameter.IntroductionRailway wheels are used to support the wagon mass and guide the wagon along the tracks (Park, 1974). The wheels and rails must be able to tolerate the applied tangential forces in order to effect wagon dynamic performance and reduce material deformation (Ghidini et al., 1994; RSE_TE_SPC_0045, 2011; AAR M107/M 208 Specification, 2011. Over the past ten years, the South African coal wagon maintenance depot has experienced excessive hollow wheel wear rates on the heavy haul line wheels. The maximum load of Jumbo wagons on the coal line is 104 t, or 26 t per axle. Although the maintenance intervention cycle for wheelsets was two years, between February 2011 and August 2012 some wheels experienced excessive hollow wear. Hollow wear is regarded as wear exceeding 2 mm on the central portion of the wheel tread (RSE_TE_SPC_0045, 2011). This happened despite the fact that these wheels were manufactured and certified according to the requirements of AAR M107/208 standard for carbon steel wheels (AAR M107/M 208 Specification,. 2011) and the local wheel RS/ME/SP 021 standard specification (RS / ME / SP / 021 REV 5 (2013). The AAR standard only specifies a minimum hardness as a required mechanical property and the local standard specifies hardness and minimum tensile strength only. In general, an increase in hardness will improve the rolling/sliding wear resistance of steel. This relationship of hardness and wear resistance was found to be true only in a situation where solid and similar alloys are in contact (Singh, Khatirkar and Sapate, 2015). The sliding wear resistance of a material is usually estimated using Archard’s equation (Liu and Li, 2001)."

Jan 1, 2016

By E. L. Smith

The development of larger size flotation machines, which started in the 1950&apos;s and 1960&apos;s, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Raghoottma S. Pandurangi, Mohindar S. Seehra, Pedro Bolsait, Bronwyn L. Razzaboni

"Surface IR (infrared) modes of crystalline and fumed (amorphous) silica particles, calcined at temperatures up to 1095°C, have been studied by Fourier transform infrared spectroscopy. The ability of these same particles to lyse cells has been measured by a hemolysis protocol. The untreated crystalline and amorphous materials differ by a factor of 40 in specific surface area, and the intensity per unit mass of the sharp surface silanol band near 3745 cm-1 in the amorphous material is an order of magnitude larger than in the crystalline material. A similar difference is observed in the lysing potential of the two materials. The intensity of the silanol band increases after calcination for both materials, reaching peak values near 500°C, followed by a dramatic drop at higher calcination temperatures, and reaching negligible values for materials calcined near 1100°C. The lysing potential data follow essentially the same pattern for both crystalline and fumed silica. These results are consistent with the hypothesis that the surface silanol groups are involved in cell lysis. Further experiments are suggested to evaluate the relationship between the surface structure of ailica particles and their potential cytotoxicity. IntroductionThe characterization of the surface structure of various allotropic forms of silica is of interest because the cytotoxicity of silica particles of respirable size has been commonly related to the chemical interaction of functional groups on the surface of such particles with the lipoproteins contained in cell membranes (1-3). It has been found that the cytotoxic potential of silica particles varies greatly with their crystalline structure (4,5), particle size (6-8), surface composition (9), and molecular surface configuration (1,10). Studies of the infrared (IR) modes of various forms of silica have been reported by a number of researchers (3 ,11-19). Several books and reviews (20-24) have dealt with the identification of functional groups on silica surfaces and the effect of heat treatment on the surface structure. The nature of the surface is said to be critical in determining the biological activity of silica dusts (3).Fourier transform infrared (FTIR) spectroscopy is a highly sensitive ·technique for identifying IR surface modes of tine particulates, and it was deemed of interest to examine the surface structure and its relation to lysing potential of two widely different types of respirable silica dust. The lysing potential of respirable dust particles has been considered a first-level test for potential cytotoxicity."

Jan 1, 1990

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

W. S. GRESLEY, Erie, Pa. (communication to the Secretary): A six-entry method of opening coal-mines is, or was a short time ago, practiced in the Connellsville coal-region; but Dr. Chance&apos;s method has a novel aspect; for while in the Connellsville region the main pillars are formed outside of two pairs

Jan 1, 1901

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal&apos;s organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors&apos; recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By M S. Cassola

It’s expected that the world economy will face a stable and continuous growth in the demand of iron ore, reaching more than two billion tonnes per year within the next year. After decades exploiting resources with high content of iron ore, now the industry faces the challenge to exploit and beneficiate more complex ores.According to the industrial practice, the flotation technology is one of the most important and effective beneficiation processes to deal with low-grade iron ores around the world. However, even with this, it is still necessary to search for new processing routes or promote the optimisation of the existing circuits.The broad application of this technology is an outcome that deeply relies on the proper selection of flotation chemicals specifi cally designed for each system. New collectors are in continuous development as flotation performance significantly relies upon their optimisation.The reverse iron ore flotation in Brazil, mainly constituted by haematite and quartz, uses ether amines as collector for silica minerals and caustic corn starch as depressor for haematite. The process selectivity is highly impacted by the features of the etheramine, such as:• mono or di-etheramine,• neutralisation degree,• chain length,• branched or linear chain,• the flotation pH, and• the size distribution of the flotation feed.This paper describes the experience obtained from laboratory and industrial trials on different ores, conducted to improve the selectivity and recovery in the reverse iron ore flotation by selecting the required collector for low-grade ores.

Jul 11, 2011

By P. C. Fletcher, E. Kaya

The Bond grindability testing procedure has been standardized to measure the same grindability values, i.e. Bond work index (BWi), for the same ore when tests are performed in different laboratories or by different operators. This is accomplished by the standardization of mill dimensions, tumbling speed, grinding ball charge weight and distribution, sample ore charge weight in the mill and operating practice. The results of this investigation reveal that the Bond work index grindability values may differ substantially with different standard Bond ball mills. This paper will review the results.

Jan 1, 2002