Search Documents

By Eric P. Bregman

As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800?s where busy commercial streets co-mingle with thickly settled residential houses. The subsurface conditions present within Boston?s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations. This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area.

By Eric P. Bregman, Franklin M. Grynkewicz, John E. Regan

"As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800’s where busy commercial streets co-mingle with thickly settled residential houses.The subsurface conditions present within Boston’s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations.This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area."

Jan 1, 2017

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By Darcey Baker

Quarry Blasting is usually boring, and that is how we like it. By this, boring means routine, straightforward, meat and potatoes blasting. Quarries typically will not utilize cast blasting, coyote tunnels, or any of the other more spectacular blasting techniques – just plain, old day-in and day-out quarry production and possibly overburden blasting. Differences in material characteristics, mining method, equipment availability, and target markets all play a part in determining the blasting procedures employed at any given location. However, variables exist everywhere and with foresight and planning, effects of tangible variables can be minimized. Variables caused by geology, weather, neighbors, or limitations caused by major plant or mobile equipment are, generally speaking, intangible; and leave the operator with finite options to improve or modify blasting procedures.

Jan 1, 2009

By Stanley A. Bunk, Desmond J. Bruyns

The purpose of roasting gold ores is to release for extraction, typically by cyanidation, the small particles of gold which are surrounded by refractory stone. The roasting simply opens up passages for the penetration of solution into the interior of the ore particles. This is accomplished by the removal by volatilization or formation of volatile oxides of certain constituents such as sulfur, arsenic or antimony. Temperature is an important parameter. High temperatures tend to form a dense iron particle rather than a "spongy" calcine. The dense iron particles result in lower gold recoveries. High temperature can cause melting of some components which also results in gold encapsulation. Roasting of refractory gold ore concentrates has been practiced for decades. Multiple hearth, rotary kiln and muffle reactors were first used for roasting. Fluid bed roasting provided a low capital cost, low maintenance technology with better process control and soon became the favored technology. The first fluid bed concentrate roasters were commissioned in the late 1940's. Early fluid beds were "bubbling" type. Environmental considerations did not significantly impact on the design. Feedstocks were highly exothermic and reaction rates were relatively rapid. Roasting today must compete with other technologies for treatment of refractory ores. Ore bodies which are not

Jan 1, 1993

By Eugene V. Cilento, R. Clark Lantz, Kevin A. DiGregorio

"A microscope-based spectrophotometer has been developed to measure superoxide release from single pulmonary alveolar macrophages (PAM) or other phagocytes in culture. Results indicate that PAM respond to stimulation by phorbol myristate acetate (PMA). It appears that some PAM do not release 02 upon stimulation by PMA; however, those that do release 0, show differences in: (I) the total amount of 0, released, (2) the rate of release of 02 and (3) the time delay for release of 02. The significance of measuring 02 release from single cells is two-fold. It allows the simultaneous study of 02 release and electrical potential changes across the membrane of PAM and it allows the study of differences in 02 release among cells. Thus, the function of Normal PAM and the dysfunction of PAM exposed to coal dusts can be more closely studied on single cells.Pulmonary alveolar macrophages (PAM), free cells found in the lungs, protect the lungs by removing inhaled foreign debris and bacteria. The macrophages do this by engulfing and then internalizing the foreign matter (phagocytosis). Stimulation of PAM causes the release of super-oxide radical (02) which has been shown to be the primary metabolite involved in the killing of bacteria by phagocytes (3,8,12). The super-oxide radical is highly reactive and is spontaneously or enzymatically converted to other antibacterial oxidants, including hydrogen peroxide (H202), singlette oxygen ( 02), hydroxyl radical toil'), and hypochlorous acid (HOCl) (2, 3,8,11,12).Exposure of PAM to dusts may lead to dysfunction of this cell-type and to a greater risk of lung damage or infection upon subsequent exposure to toxic dusts. To date, much of the research with this cell-type has used cytotoxicity (cell death) as a measure of dysfunction. Although this is an important end point, PAM dysfunction may occur at doses below those which lead to cell death. In addition, dysfunction has been measured using large numbers of cells. In order to obtain a clear understanding of the mechanisms involved in dysfunction, measurements should be made on single cells. As mentioned earlier, one of the major roles of this cell type is its anti-bacterial actions. Therefore, asessment of release of superoxide radical in single cells is important in determining the functional behavior of PAM before and after exposure to dusts. Since measurements of 02 production have not been made on single cells the purpose of this study is to develop the methodology needed to study release of 02 from single cells.Recent studies have suggested that a relationship exists between the release of 02 and changes in the electrical properties of phagocytes. The change in membrane potential is thought to be the initial step in superoxide production (6,9). Stimulants which cause 02 release also cause changes in the transmembrane potential of phagocytes (9) and in the permeability of the cell membrane to ions (6). For example, stimulants which cause the release of 0, from neutrophils have also been shown to increase the membrane transport of Na+ , K+ and Ca+2 and stimulation of macrophages leads to increases in Na and perhaps Ca permeability with a subsequent change in membrane potential. In some cases, phagocytic activity has been shown to depend upon the extracellular concentrations of these ions (6). Holian and Daniele (7) have shown evidence that the redistribution ofcellular Ca in alveolar macrophages is an initial step leading to 0, release. In order to provide direct evidence that 02- production is related to electrical changes across the plasma membrane of phagocytes, these two phenomena must be analyzed simultaneously on single cells. Ultimately, measurements of 0, release using the methodology developed in this study will be combined with electrophysiological tech¬niques to study both superoxide release and membrane potential changes simultaneiously on single PAM, and to examine the effects of coal and mineral dusts on their physiological fu"

Jan 1, 1988

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By John J. Reed

Since the beginnings of, the human struggle for survival and improvement, mining has been one of the basic endeavors of life. Until relatively recent times it was classed as an art. Now we are at work trying to, raise mining to the level of an engineering science where it belongs if we are to prosper. It should be self-evident that this goal can be attained only through industrial progress: based on education and research. It is true that our industry, left to itself, will develop a few new ideas and techniques through the years. However, we mining' engineers are relatively few in number compared to the other disciplines, and the rate of our improvement by such "accidental" discoveries is simply tooslow to keep pace with the rest of our technical civilization. It will be evident in the remarks that follow, that the rapid development of mining education, research, and the industry are extremely interdependent, and will be largely controlled by the amount of cooperation, support, and cross-fertilization that can be developed among all three.

Jan 1, 1961

By E. Demir

Transportation cost is the dominant cost and accounts for almost half of the total mining cost in surface mining. Therefore, determining transportation cost is critically important for the economic feasibility of mining projects. Turkey produces around 85 million tons of lignite per annum. The biggest state-owned company, Turkish Coal Enterprises (TKI), accounts for 43 per cent of the country?s total lignite production. Around 85 per cent of the produced lignite is used in power plants for electricity generation and 15 per cent is used for domestic heating in cities and urban areas. On behalf of the Turkish government, TKI distributes around 2 Mt of lignite annually, at no cost to poor needy families countrywide in accordance with Social Assistance and Solidarity Funding aid. Subcontractors are utilized for lignite transportation, and conflicts arise due to the different transportation cost calculations at different mines. A robust model that provides unbiased cost estimations is therefore of paramount importance. This paper presents the transportation cost estimation software, NAKMAL, that has been developed for estimating the transportation cost of lignite from the mine face, including excavation and loading, to various final destination points through five different transportation scenarios. NAKMAL was designed using VisualStudio.NET, validated using field data and some case studies, and it is currently being used by TKI for calculation of transportation cost country-wide.

Jan 1, 2012

By Thenepalli Thriveni, Ch. Ramakrishna, Yujin Jegal, Ji Whan Ahn, Jyothi Rajesh Kumar

In alumina production or alumina refining, bauxite is converted to alumina (aluminium oxide) The rare-earth elements (REEs) are a group of 17 chemically similar metallic elements (15 lanthanides, including scandium and yttrium). Rare earth elements play a key role in many industrial applications, petroleum refining, clean energy, automobile, electronics, and defense applications. These rare earths are essential to the success of green technologies. China today controls more than 95 percent of the rare-earth supplies and nearly all rare-earth refining and after 2009 year rare earths crisis raises due to China’s export restrictions and growing internal demand for rare earth elements. The extraction of gallium and yttrium from Korean red mud (KC red mud) by selective acid leaching was explored. The recovery of gallium and yttrium from a leach solution of the Korean red mud using solvent extraction was studied. A number of extractants were investigated for the extraction of those mentioned two rare earth elements and also we proposed a flow sheet of rare earth elements respectively. The toxic heavy metals presented in KC red mud were removed by CO2 stabilization.

Jan 1, 2015

By Vijaya Bhushan Rao, Jason Redgers

A substantial lifestyle destination in the United Arab Emirates, in the Emirate of Abu Dhabi comprising of 1315 villas, town houses and non-residential leisure facilities is built over an area of 280 hectares of former mangrove areas, natural sands and reclaimed lands. Large-scale subsoil investigations including field and laboratory testing carried out dividing the entire site in to 7 clusters. This investigation revealed alternating layers of loose sands and silty clays within the load influence zone of planned foundations, showing susceptibility to excessive settlements. Therefore, ground improvement works were undertaken using a combination of stone columns, Rapid Impact Compaction (RIC) and excavation and replacement of soils plus a 0.4m thick load transfer platform. This was necessary to limit the settlements, increase-bearing capacity and prevent long-term settlements. 30 no’s of full-scale Zone Load Tests, ZLT were carried out each for a duration of 30 days in order to ascertain the anticipated long-term settlements in the clay layers. In addition, further testing of electrical cone penetration tests, CPT, and Plate Load Tests, PLT. The use of Priebe and Asaoka’s observational procedure were applied to predict the final settlements and the use of back-analysis from the 30 days Zone Load Tests, ZLT results to establish the site-specific consolidation parameters in clay layers to optimize the design and ground improvement works.

Sep 8, 2021

By Wallace N. Thomas

The present interest in large diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a seven to eight thousand horsepower mill will cost from 1350 thousand to $600 thousand which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functions -- establishing a realistic compromise between cost and performance.

Jan 1, 1969

By Wenjie Zhu

Chromite ore processing residue (COPR) is a hazardous waste containing high concentration of chromium. We describe here a pioneer trial of detoxification of COPR in column reactor with an indigenous chromate reducing bacterium Leucobacter sp. Ch1, which showed high chromate reducing ability at high pH. Under the optimum conditions, at 30°C and pH 10.0, pH of leachate decreased from 10.3 to 8.3, and Cr(VI) concentration in solution decreased to zero mg L-1, and 76.4% of Cr(VI) was removed from COPR samples. The leaching toxicity of detoxified residue was 1.1 mg L-1 that was lower than national standard of China.

Jan 1, 2008

By R. P. King

The MODSIM mineral processing plant simulator is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open-and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Jan 1, 1997

By P. K. Arya

Huge quantity of copper is lost in Crown, Sill, Rib Pillars, hanging wall, foot wall and unexploited ore bodies in several closed underground copper mines and old worked out stopes of Hindustan Copper Limited at Mosaboni and other places. These mines might have been uneconomical to work with conventional mining methods. However, huge quantity of mineral reserves is lost due to their closure. Chemical and in-situ bio-wash leaching, if tried can provide an answer to facilitate the recovery of metallic values economically. Encouraging results were obtained during an experiment at North Badia Mines at Mosabani in the past. Though the experiments were not completed but whatever results obtained were very encouraging and can be successfully tried to make it viable. The results of the experiments are discussed here and a plan is suggested to recover copper from such mines.

Jan 1, 2014

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By G. Stephan Derrickson

Any type of agitation within a confined vessel is primarily concerned with two parameters: 1) A level of agitation describing the homogeneity of the constituents (whether it be suspension or mixing) and, 2) the energy efficiency with which this level of agitation is accomplished. The following is an attempt to present a solution to the problem of adequately defining and optimizing these properties. First included is a discussion of the application of good design practices to the determination of a mechanically efficient shape to the blade elements of the propeller. These practices, excluding several appropriate modifications, have been known, but not well understood, in aircraft fluid mechanics for a number of years. Secondly, having optimized the direct impartation of energy to the medium being agitated, attention is turned to one of the more perplexing phenomena of multi-phase systems - definition and prediction of agitation levels. The result of recent study and testing is a method of scaling which the authors feel provides a lucid understanding of governing physical parameters within the agitator itself, allowing one to scale up and down with confidence.

Jan 1, 1982

The paper continues an account, begun in a previous paper, of experimental work carried out by the author whilst a member of the metallurgical staff at the Cockle Creek Works. The general method of the description of the plant and works practice adopted previously has been followed.The paper is a short account of the methods used in and the results of an investigation of the fume losses from the various parts of the plant.MEASUREMENT OF VOLUMETwo independent methods were used. The first depended on a number of pitot-tube measurements of velocity. These readings were taken in the stacks leading from the various furnaces at a considerable height above the ground so as to obtain as regular conditions as possible at the points where the readings were taken.Three openings were made in each stack and the pitot tube inserted into each opening in turn and readings taken at the centres of imaginary areas of equal size. The average velocity in the stack was thus obtained.After four tests had been made at the smelter stack, which removed the gases from all blast furnaces in use, the centre of velocity of the gases for each test was calculated and was found to be practically constant in position. The previous procedure was varied in subsequent tests on this stack by taking a succession of readings at the centre of velocity instead of at various points...

Jan 1, 1925

By Frederick McNeill, John Harper, Mahmood Khwaja, Shawn Lavoie, Timothy Cloughert, David Polcari

City of Manchester, NH, is implementing a 20-year plan to control and significantly reduce overflow of its sewer system. The long-term control plan had called for large scale box culvert installation through downtown Manchester. The City and the project team evaluated, and eventually selected, tunneling as an alternative to mitigate construction related impacts for open trench approach. This paper provides an overview of the alternative evaluation process; discusses the development of the preliminary design for the 12,000 feet long, 12-ft internal diameter tunnel, including plan and profile selection, subsurface conditions, drop shafts and the anticipated packaging of the separation areas.

Dec 1, 2022