Search Documents

By P. D. Lindahl

[A cost/benefit analysis was conducted by comparing the industry cost to protective structures on low-coal face equipment with the benefits paid for injuries/fatalities considered preventable by the use of these structures. Th industry costs were based on estimates by OEM's and rebuild shops for install protective structures on new and rebuilt face equipment. The accident benefit was based on evaluations performed by the USBM Accident Cost Indicator Model. Industry wide population data were developed on low-coal face equipment and injuries/ fatalities preventable with protective structures. The results of the analysis are to be used as a tool by USBM in determining the feasibility of continuing development of cab and canopy technology for low-coal equipment.]

Jan 1, 1983

By Samer Sadek, Phoebe Cheng, Changmo Kwon, Myat Ohn

BART Facilities Standards (BFS) Structural Criteria is a living document that governs planning, design, and construction of all BART projects. Since its development, the document undergoes incremental changes and updates to reflect policy changes, changes in local, State, or national design codes and guidelines, advancements in engineering and technology, or based on the performance of past built infrastructure. In 2020, the BFS-Structural Criteria underwent a comprehensive update and was released with BFS version 3.2. This paper summarizes the updates to the Tunnels and Underground Structures Section of the Structural Criteria, and provides insights to the basis and logic of the requirements.

Dec 1, 2022

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991

By H. D. B. Wilson

"IntroductionRECENT ADVANCES in geo-chemistry and in •our knowledge •of crystal structure provide a key which enables us to create a systematic picture of the genesis of many ore deposits. This genetic scheme may be used with confidence in assessing certain types of orebodies and may be of some aid in actual exploration, since it affords a rational explanation of the dependence of the composition •of the ore minerals on that of the rock type in which they occur with which they -are •associated. For purposes of the present paper, .the elements chosen are •chromium, vanadium, iron, and titanium. The oxides of all these metals occur in deposits of similar or related type, and it is proposed to show that, for each, the composition of the •ore mineral is related to •the composition of the enclosing :rock, and that one of the principal factors controlling the composition of the ore is the ionic size of its constituent elements.Geochemical PrinciplesThe crystals of the rock-forming silicates and of the magmatic oxide minerals are essentially ionic types. This means that they are composed •of oppositely charged ions such as Mg²+ and 0²-, which are held together by electrostatic attraction. The ions of each element are spherical, with characteristic size known as the ionic radius. Crystals are built up by the packing of these spheres in the most stable arrangement compatible with the size and the size and valence of the ions• involved.Many of the principles governing the formation of ionic crystals are •simple ,and logical."

Jan 1, 1953

By Dieter Loh, Mathias Knoll, Florian Werres

When a new tunnelling project starts, it has been a vital tradition for decades to cast and erect master rings horizontally on a flat surface to demonstrate the compliance with dimensional tolerances. Some tenders ask for the erection of two or even three rings upon each other or repeated master ring erections at intervals throughout the project. Especially for large diameters, this is a challenging and risky task for the workforce in the segment factory. A truck-mounted crane is often necessary, and in some cases it can take up to a week to complete a master ring. The concept of virtual rings has the potential to replace this tradition by assembling master rings digitally instead of physically. This is based on a best-fit approach, considering the 3D coordinates from laser tracker measurements of segments or segment moulds. Building a virtual ring, a sub-millimeter accuracy can be achieved, the alignment of neighboring circumferential and ring joints observed, and the fit of bolt holes checked. The traditional method, on the other hand, is discussed controversially despite the significant amount of work and risks—particularly as the horizontal position of the ring and absence of gaskets do not simulate the reality in the excavated tunnel. This paper will highlight the technical aspects of virtual rings, as well as their pros and cons, illustrated by a case study from London Thames Tideway where a total of 30 physical master rings could be replaced by virtual rings.

Jun 13, 2023

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

By Gordon Chen

The Block 37 Chicago Transit Authority (CTA) Tunnel Construction Project was originally designed by STV to connect Blue Line subway in North Dearborn Street and Red Line subway in State Street in the downtown Chicago Area. The project was proposed using tunnel mining techniques combined with steel pipe jacking and fiber glass rebar soil reinforcement. Weidlinger Associates, Inc. (WAI) and Kiewit Construction Company proposed an alternate design using open cut construction technology. WAI designed a complex temporary excavation support system using Soldier Pile Tremie Concrete (SPTC) walls and Soldier Pile Lagging walls supported by cross lot/corner bracing elements. Below the top of the existing tunnel, a top-down construction technique was utilized. A steel temporary traffic decking system at top of the excavation site served as the daily street traffic function as well as the first level of bracing for the support of excavation. The project encountered great challenges of soft clay conditions in downtown Chicago, numerous existing utilities in the excavation site and the requirements of protection for a number of historical buildings nearby as well as the protection of the city streets. The construction was successfully completed at both State Street/Washington Street and Dearborn Street/Randolph Street. The monitoring system showed that ground movement and adjacent building settlement was kept to a minimum during construction.

Jan 1, 2009

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

By E. V. Leont'eva, V. R. Vafin, A. G. Kladova, N. L. Medyanik, A. P. Ponomarev

"The thermochemical technology for recovery gold, silver from mature flotation tailings of pyrite ores by two-stage sintering with chlorine-ammonium reagents and leaching of bakes with water is developed. The economic effect of the technology implementation is calculated. KEYWORDS Gold and silver recovery, mature flotation tailings, pyrite ores, chlorine-ammonium reagents, leaching INTRODUCTION The relevance of processing the technogenic reserves of ore mining and concentration wastes accumulated over the long operation periods of mineral deposits is beyond doubt. Hundreds of tons of precious and non-ferrous metals that were not recovered during the primary processing are concentrated in the accumulated wastes. For example, tailing storage facilities (TSF) at the mineral processing plants in the Southern Urals region of Russia hold more than one hundred tons of gold and thousands of tons of silver in the mature flotation tailings (MFT) of copper pyrite ores. Secondary processing of technogenic materials is facilitated by the fact that they are preprocessed — ground and compactly deposited on the surface, but complicated by the low (compared to ores) grade, uneven distribution of the valuable minerals, altered and unstable material composition of the mineral feed. This leads to low recovery rates of valuable metals by conventional physicochemical processing methods. It is necessary to develop innovative methods of deep integrated processing of industrial wastes, based on the study of the material composition of specific technogenic mineral resources and based on ensuring the environmental safety of the resulting secondary waste. MATERIALS AND METHODS The object of this study are the MFT of Uchaly Concentrator in the Republic of Bashkortostan, Russia, which processes copper pyrite and copper-zinc ores. According to the data of particle size, chemical, X-ray phase, and optical microscopic analyzes, samples of the MFT are characterized by considerable particle fineness (the fraction of the size class -41 µm is 89-90%), low grade of gold (1.7-2.0 g/t) and silver (18.0-19.5 g/t), comparable grades of iron (23.0-26.8%) and sulfur (28.1-28.7), but different grades of copper (0.12 - 0.73%) and zinc (0.34-1.26%). The most common mineral in the samples is pyrite (50 - 56%), found in intergrowth with grains of other sulfides (0.1-4%) - sphalerite, tennantite, chalcopyrite, covellite. Quartz and aluminosilicates are the dominant rock minerals (21-36%). Based on the results of the phase analysis, it was established that approximately 70% of the gold in the samples is found in a form that is resistant to cyanidation — it is locked in sulfides (52-56%) and quartz and coated by films. Along with sulfides and rock minerals, common gold and silver minerals (chalcogenides, intermetallides, native gold) in the form of submicro- and nano-sized precipitates are also associated with intergrowth of a complex structure. These features of the material composition allow classifying the MFT of the pyrite ores as a mature feed material and emphasize the need for chemical non-cyanide methods to recover gold and silver from the mature minerals and associations they are found in."

Jan 1, 2018

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By N. Gopalakrishnana, R. Beccard, S. Lourdudoss, R. Holz, M. Deschler

"Rapid growth of conducting and/or insulating InP, GaAs, Gao.47In0.53As, and GaAs0.6Po.4 on one or more of (001), (110), (111)A, (3ll)A and (3ll)B surfaces by Hydride Vapour Phase Epitaxy (HYPE) is demonstrated. The maximum growth rate of the binaries lies between 12 and 300 µm/hr and of the ternaries between 7 and 170 µm/hr. A simple model is developed to describe the influence of crystallographic orientation on temperature dependent growth rates. The growth rates predicted by the model is compared with the experimental values. Room temperature resistivity of insulating InP:Fe can be as high as 5xl09 ohm cm. Temperature dependent differential resistivity is also analysed. This feasibility of growing conducting and insulating layers rapidly on different orientations is very useful for electronic and optoelectronic devices.IntroductionRecently there is a renewed demand for very thick layers of III-V compound semiconductors for high performance electronic and optoelectronic devices [1]-[2]. Long wavelength high speed lasers that can be modulated up to 30 GHz necessitate epitaxial growth of semi-insulating (SI) layers [3]. There is also an increased interest on the growth of epitaxial layers on surfaces other than (001) surface. Epitaxial growth of these materials on such surfaces is of theoretical importance besides being technologically relevant. These demands led us to focus on the growth of conducting and insulating III-V compounds by Hydride Vapour Phase Epitaxy (HYPE). lnP, GaAs, Gao.471no.s3As on lnP and GaAso.6Po.4 on GaAs were grown as conducting materials using Low Pressure HYPE (LP-HYPE) on (001) 2° off substrates. Gao511no.49P on (001) GaAs substrate and lnP on lnP substrates of (001), (110), (l 11)A, (31l)A and (3 ll)B orientations were grown as semi-insulating materials using Atmospheric Pressure HYPE (AP-HYPE). In this report we present the growth aspects of these materials. We also present a simple model on the growth of InP on substrates of various orientations. The theoretically obtained temperature dependent growth rates are compared with the experimental values. Differential resistivities of semi-insulating lnP grown on substrates of various orientations as a function of temperature are also summarised."

Jan 1, 1998

By Martin N. Kelley

The Great Belt Link is a $3.5 billion fixed link across an 18 km (12 mile) wide body of water that separates the island of Zealand, on which Copenhagen is situated, and the main land mass of Denmark, Jutland, which is part of the European continent. The project consists of three main contracts. The first contract is an 8 km (5 mile) long, two-bore railway tunnel for the eastern half, the second contract is a 6.6 km (4 mile) combination railroad and highway bridge for the western half, and the third contract is a 6.7 km (4 mile) long high-level highway bridge for the eastern half. This paper will discuss the Eastern Railway Tunnel Project and the methods of construction that the joint venture consortium plans to use, along with its equipment selection. The ground conditions to be encountered begin with glacial tills, which are a mixture of clay, silt, sand, gravel, cobbles, and granitic boulders. The boulders can be up to 1-3 m (3-10 ft) in diameter. Underlying the till is a marl which is sometimes highly fractured with hydrostatic pressures of up to 8 bar. About 40% of the tunnel is in till and 40% in marl, with the remaining 20% being a mixed face of the two formations.

Jan 1, 1991

By Alena Conrads, Markus König, Markus Scheffer, Markus Thewes, Hannah Mattern

"INTRODUCTION In recent years, the development of tunnel boring machines has revolutionized the tunneling industry. The general structure of a tunnel boring machine (TBM) can be described as a multi-component system. To achieve high performance rates, machine elements have to perform reliably. Performance losses and interruptions of the construction process should be prevented or at least, reduced to a minimum. In order to achieve high advancing rates, cutting tools must be in good condition at any time. Furthermore, failure of individual tools might result in increased and faster wear of remaining structural components. For this reason, maintaining and replacing cutting tools is crucial to prevent project delays due to insufficient boring performance. Precise prognoses concerning the prevailing geology are infeasible and thus, efficient scheduling of maintenance actions is challenging. The intention of this work is to analyze different approaches of TBM maintenance in soft ground. Different strategies are analyzed by the use of a simulation approach. Cutting tool condition is regarded as performance limiting factor. The maximum operation time of the cutting tools is determined using the “Soil Abrasivity Index”. A case study serves to show the effects of different maintenance strategies on total project duration. SCHEDULING OF MAINTENANCE ACTIONS Scheduling maintenance actions of single and multi-component systems concerns numerous fields of industrial production. Concentrating on mechanized tunneling in soft ground, cutting tool maintenance represents the most common reason for intermission of advance (Köppl 2014). In literature, time-based and condition-based maintaining techniques are widely discussed. The following section outlines the principles of time- and condition-based policies. Furthermore, examples for their applications in recent research are given. Time-Based Maintenance In general, the time-based maintenance approach assumes that the failure behavior of the system components is predictable. Maintenance actions are scheduled according to predefined intervals (e.g., hours, days, weeks). A detailed analysis of preventive repair times or interval forms the basis for maintenance decisions. For this approach, an adequate quantity and quality of data is fundamental. Numerous studies deal with the analysis of time-based maintenance for production equipment. In fields of mechanized tunneling, unplanned machine downtimes restrict the applicability of time-based maintenance approaches. Thus, this paper mainly focuses on condition-based maintenance."

Jan 1, 2016

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By E. Peters

Roasting processes are divided into several elementary mechanisms, any of which could be significant or pre-dominant in a particular roast. The elementary processes considered in-elude beat transfer, gas-solid inter-actions with accompanying mass transfer between the bed and furnace atmosphere, vapor phase transport processes in solid-solid interactions, and solid phase diffusion processes. Examples are chosen of processes in which one of these mechanisms pre-dominates and some recently obtained data is presented to support the existence and significance of these mechanisms. Proposals are also made for future research in these areas, and for utilizing the information in the improvement of roaster capacities’ OASTING of ores as a preparative treatment for smelting or leaching has been practiced for so long that its origin has been lost in antiquity, but little has been under-stood of its basic nature until fair-ly recent times. The nominal chemistry of roasting processes is now understood; that is, the initial chemical com-pounds present in the ores or con-

Jan 1, 1961

By Walter K. Utt

The U.S. Bureau of Mines conducted research to develop an accurate, real-time, position monitoring and warning system for the vehicles used in surface mining. The product of this research will be technology to reduce accidents and injuries associated with the operation of surface mining haulage equipment. The position monitoring system should reduce accidents related to vehicle position and also increase the efficiency of haulage operations. This research was conducted in preparation for development of an accurate, real-time position monitoring and warning system, which notifies equipment operators when they deviate from a known safe course and are approaching a fixed hazard. A radar positioning system designed for marine applications was evaluated and a series of tests was run to determine the accuracy of the radar positioning system when used in a land vehicle. The radar position determination was compared to surveyed values. Both static and dynamic (moving vehicle) tests were conducted. The static test results were marginal and the dynamic test results were not accurate enough for the position monitoring and warning system. Although a promising technology, the system tested needs to be modified to meet the accuracy requirements of mobile mine equipment.

Jan 1, 2010

By Shengli Wu, Mingyin Kou, Feng Chang, Laixin Wang, Hua Lu, Jianliang Zhang

Sintering dust has been regarded as an important secondary resource in a modern steel plant. Sintering dust was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particle size, specific surface area, particle morphology, and lattice parameters of activated sintering dust were determined. It was found that the agglomeration of the particles take place during extended dry milling with accessible pores for Nitrogen gas. The maximum specific BET surface area in the stirring wet grinding and planetary wet grinding increases to 43.06 and 46.45 m2/g after activated 360 min respectively. With the increasing of energy input, the intensity of diffraction peaks of dolomite and hematite gradually decreased. Furthermore, the previous phase almost disappeared eventually under any experimental conditions. In addition, Fourier transform infrared spectroscopy indicates that organic matter and carbonate decompose easier than other phases, especially under stirring wet milling.

Jan 1, 2016

By Paul G. Marinos, Vassilis Marinos, Evert Hoek

The Geological Strength Index (GSI) is a system of rock mass characterization that has been developed in engineering rock mechanics to meet the need for reliable input data related to rock mass properties required as input for numerical analysis or closed-form solutions for designing tunnels, slopes, or foundations in rocks. The geological character of the rock material, together with the visual assessment of the mass it forms, is used as a direct input for the selection of parameters for predicting rock mass strength and deformability. This approach enables a rock mass to be considered as a mechanical continuum without losing the influence that geology has on its mechanical properties. It also provides a field method for characterizing difficult-to-describe rock masses. Recommendations on the use of GSI are given and, in addition, cases where the GSI is not applicable are discussed.

Jan 5, 2007

By J. D. Price, W. M. Bertholf

A. C. RICHARDSON*—First of all, [ think that the paper represents a lot more work, study, and correlation than has been indicated by the brief talk by Mr. Price. I like the way he started out and described the areas from which the samples were obtained, the locations of the washing plants, the available tonnages, and other background information with which to evaluate the data he submitted later on. Then I like the way in which he described the various types of washing plants, the tonnages handled and the difficulties of the washing problems; showing the amount of material that lies close to the specific gravity at which the washing separation is made. Later he gave figures from washing plant operations showing recoveries and cleaning efficiencies. He then discussed his own plant at Pueblo. It is the same old plant, I think, that I worked around a good many years ago. It is unusual to find a plant treating nearly 5000 tons of coal a day on tables. But this table plant is, I believe, more efficient than is indicated by the figures that Mr. Price gave. To determine the efficiency of a cleaning operation or to compare it with another it is necessary to consider the quantity and character of the material close to the specific gravity at which the separation is made. It is not fair, I believe, to penalize the table operation by something like 4 pct of out-of-place-material as he has done here. The variety and difficulty of the coals that he has to wash, the continuous shift and change in their composition make a very difficult cleaning problem and the table performance is excellent. I believe that the information in this paper will be of interest and value to anyone operating or planning to build a coal cleaning plant in this or other areas; particularly where the cleaning of fine coal is a problem. The data may be used for comparative purposes in determining the relative efficiencies of other cleaning plant separations. E. D. HAIGLER*—What is a Baum jig? J. D. PRICE (authors' reply)—A Baum-type jig is one in which the pulsations of the water is secured by means of a pulsating air current applied on top of the water. I imagine you are all familiar with the old plunger-type jig which is in effect a U tube in which a plunger on one side of the U, moving up and down, causes a corresponding pulsation on the far side of the jig. In the Baum jig, the pulsating air current is applied on the surface of the water on one side of the U tube of the jig and gives a corresponding pulsation on the other. It is also commonly known as a pneumatic jig. The control of the rise and fall of the water in the jig body proper is under much better control than it is in any of the other type jigs. Mr. Richardson could enlarge on that feature, for I know that he has had considerable experience with these jigs. A. C. RICHARDSON—You have asked how to control a Baum-type jig. The pulsations in a Baum jig can be modified and regulated to a marked degree by the amount of water admitted to the jig and by the adjustments of the valve which regulates the manner in which air is admitted. The number of pulsations per minute is controlled by the number of cycles of the air valve. Thirty to forty cycles per minute is a good speed for large jigs treating coarse sizes of cod. With an air valve it is possible to modify the time-velocity curve of the pulsating water to some extent which in turn determines the action in a jig bed. Within limits the following parts of the air valve cycle may be regulated: (1) the rate and period of air admission, (2) the period of air expansion, (3) the rate and period of air exhaust, and (4) the period of air compression. The rate and period of air admission determines the acceleration of the water at the beginning of the pulsion stroke and the amplitude of the stroke. The period of air expansion, after inlet port is closed, is one in which the water has reached the desired velocity, positive acceleration reduced, and the bed held in a mobile condition. The rate and period of the air exhaust can be adjusted to modify the degree of suction and so modify the manner in which the particles in the bed stratify. The compression period, alter the exhaust port closes and before the intake port opens may be used to advantage in retarding the downward velocity of water during the suction stroke. An ideal jig stroke is one in which during the up stroke the bed is lifted slowly in a mass and opens up like an accordian with the bottom layers dropping away first. With the bed open and mobile the particles adjust themselves according to their hindered settling rates. During the down stroke, while the bed is still open the particles of high specific gravity are accelerated toward the bottom layers. It is possible to approach this stroke with all types of jigs but it is less difficult to approximate it with a Baum jig.

Jan 1, 1950