Search Documents

By K. R. Vost

This paper reviews the theoretical methods used in South Africa for the prediction of heat pick-up and air-temperature gradients along main haulages. These methods include those of Starfield, Ramsden, McPherson, and Goch and Patterson. The differences in predictions based on typical airway conditions are explained as being due to differences in the mathematical models on which the predictions are based. The largest discrepancies were found for dry airways and for airways with bulk air coolers. The errors in predictions of the effect of machines and coolers that have been running for only a few months are calculated, and the limitations of various simplified methods are discussed.

Jan 1, 1982

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By S. Rezaei

Moving ground in the mining industry is almost inevitable; however comprehensive awareness of these movements is necessary to mitigate risk. Monitoring of displacements caused by mining is a key tool for geomechanical risk management. Good monitoring may prevent unexpected failures and protect personnel and equipment. Many displacement monitoring techniques are available, however not all are reliable, accurate, and cost effective. Close range photogrammetry (CRP) is a monitoring method with high accuracy, reliability, and cost effectiveness; and has the ability to measure places that are inaccessible. In CRP, some series of photos are taken in different positions with different angles at different time intervals depending on the displacement rates. These photos are processed using PhotoModeler software and 3D models are made. By comparing 3D models, displacements can be measured. This method has been demonstrated at the Freeport-McMoRan Safford Mine in Arizona. A fault related instability in part of the pit is reactive to mining, and provided an opportunity to compare results between traditional monitoring methods and CRP. In this project, multiple series of photos were taken at different times using a Canon 5D Mark III digital camera, then PhotoModeler software used to make 3D models for each specific measurement event. Movement rates were determined by comparing different 3D models. These results are then compared to results of other monitoring methods to validate the CRP displacement method.

Feb 27, 2013

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By Frank Matter

Production of ultrafine powders of industrial minerals has been a problem in the past. In recent years new wet and dry grinding stirred ball mill systems have emerged which have been commercialized Two such systems are the TRZK mill with double step air classifier for dry grinding and the NRZK mill for wet grinding The primary features of these mills are feed entering from top and the product along with the grinding media leaving from the bottom, and a media separation and recycle system A detailed description of the NRZK mill for grinding coal is presented

Jan 1, 1983

By C. J. Bechtoldt, H. C. Vacher

Quenched alloys, prepared by powder metallurgical techniques, were examined by microscopic and X-ray diffraction methods. The compositions and heat treatments were chosen so that the chromium and nickel solvuses could be determined and a range of composition and temperature, in which a eutectoid had been reported, could be explored in small intervals. The results showed no evidence of eutectoid reactions having taken place. ALLOYS containing iron, chromium, molybdenum, and nickel are extensively used in high-temperature applications. In order to provide basic information on the solid-state reactions that occur in such alloys, the National Bureau of Standards is engaged in an extensive study of the equilibrium phases in the binary, ternary, and quaternary systems involving these four metals. Attention was directed to the chromium-nickel system because a review of the literature showed conflicting data. A recent compendium1 of the constitution of binary alloys gives two diagrams for the chromium-nickel system, one a simple eutectic and the second a diagram showing a eutectoid and a eutectic. The eutectoid was the result of an allotropic transformation in a high-temperature solid-solution form of a chromium-rich phase called 0. The approximate temperature and composition of the eutectoid was 1200°C and 30 at. pct Ni. In the preliminary study, at the Bureau, no transformation was indicated in the chromium-rich phase of ternary and quaternary alloys in which chromium and nickel were major components. Similar results have been reported from time to time in the literature,2-8 In consequence of this situation, a systematic study was made of the constitution of heat-treated chromium-nickel alloys using metallographic and X-ray diffraction methods. The compositions of the alloys were selected so as to determine the boundaries of the chromium-rich and the nickel-rich phases and to explore in small intervals the ranges in composition and temperature in which the eutectoid had been reported. The results of this study are reported and discussed in the present paper. EXPERIMENTAL PROCEDURES Materials, Alloys, and Heat Treatments—The alloys were prepared by a powder metallurgy technique similar to that used in earlier work.9 Analyses of the materials used are given in Table I. Powders were mixed using a vibrator in 30-g batches of predetermined composition; 2-g pellets were made from the mixture by compacting at room temperature in a 1/2-in. diam mold under 60,000 lb per sq in. pressure. The pellets were sintered in dry hydrogen for 10 days at 1300°C. At the end of the sintering treatment the specimens were quenched in water, which caused a pale green film to form on the chromium-rich alloys and thin black scale to form on the nickel-rich alloys. The pellets after sintering were approximately 1/2 in. diam by 3/32 in. thick. The purification train9 was modified by inserting a tube of titanium turnings, heated at 700°C to increase the efficiency of the removal of oxgen and nitrogen. It was found in the earlier work that the sintering treatment lowered the carbon, oxygen, and nitrogen contents of chromium-rich alloys to 0.01, 0.01, and 0.004 wt pct, respectively, and that there was a loss of chromium. In order to ascertain the extent of this loss, the chromium contents of certain alloys were determined chemically. They included those alloys used to determine the parameter-composition curves and those of critical composition, used to determine the chromium-solvus microscopically; these analyses were made on samples after the final heat treatments. The mixed powder values for the chromium content of those alloys that were not analyzed were adjusted to conform to a smooth curve based on the chemically analyzed values for

Jan 1, 1962

By Raissa Santos Salgado

O refino primário através dos convertedores BOF representa uma etapa fundamental na fabricação do aço. Em meio a um mercado desafiador e competitivo, estabilidade operacional e inovações são necessárias para alcançar qualidade e preços razoáveis. Com o intuito de estudar o sopro combinado através de um modelo físico, similar com convertedor da thyssenkruppCSA 330t, foi utilizada uma análise visual associada a métodos colorimétricos para mensurar a penetração do jato e a melhor configuração de ventaneiras. Com base nesses métodos, encontrou-se a distância banho-lança que reduz o tempo de mistura com menor probabilidade de slopping. A partir dos resultados obtidos no modelo a frio, os parâmetros foram recalculados para a prática industrial.

Oct 30, 2017

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By K. L. Hardee

A recent development has emerged which produces a retrofittable, low cost anode by attaching disposable, electrocatalytically active titanium mesh over the existing lead anodes. The coated titanium mesh anode operates at potentials of several hundred millivolts lower than the lead anode, providing significant power savings. The exposed lead surfaces are stabilized since most of the current flows through the titanium mesh. With the minimal lead corrosion, the sludge formation is virtually eliminated and the purity of the plated copper is greatly enhanced. Further savings may be realized by the elimination of non-essential chemicals such as cobalt. Since the combination anode is stable and uniform, the plated copper is also more uniform with minimal formation of dendrites, reducing the shorting. Full-size anodes have been tested for over 6 months in commercial copper electrowinning cells. The laboratory and field performance of the stabilized lead anode will be reviewed, including the voltage characteristics, the lead stability and the copper cathode purity.

Jan 1, 1999

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010

By Donald R. Simon

Money... not many subjects are as personal or as emotional. Hessiod said it well in 700 B.C. "Money is life to us wretched mortals". Are you getting paid enough? Does your company reward its top people? Does coal or copper pay more? Production or engineering? How is the synfuels industry going to influence mining salaries? Do high salaries attract and retain the best people? Do modern compensation systems ensure fairness or destroy entrepreneurial spirit? With our tax system and high standard of living why are we so salary conscious? Salary is not only important for what it can purchase but it is also a yardstick, measuring how well we are doing. We all need money to pay the bills and maintain our standard-of-living, but once we reach a certain point the psychological ramifications become more important than the purely practical side. Even necessary payments like the mortgage and the car are a function of our egos. Are our choices of cars and homes based on simple transportation and shelter?

Jan 1, 1980

By P. Matias

The study involved two projects that will produce copper concentrate and may have their operations integrated. Transport by trucks, conveyor belt, and the equipment called RopeCon were evaluated as options for the ore transport between the sites. A rainforest stretch, that Vale S.A. demands to preserve, is situated between the projects. It was suggested to further review RopeCon because it presents minimal interactions with the environment. To design the preliminary system layout, a research was done on the rainforest cover height data, but the information found was scarce and imprecise. For preserving the local forest, the use of this data would conduct to the oversizing of RopeCon towers and, consequently, overestimation of its costs. For the acquisition of reliable information, a method was developed using local data acquired through airborne laser survey. The volume between the digital surface and terrain models was calculated to generate a surface representing the forest cover height. It was revealed, by plotting the points obtained from this surface, that 85% of the vegetation is below 25 m. This height is suggested to review the preliminary project with a more accurate design of the equipment towers, thus reducing its costs estimates. The method permits the precise location of the large trees, making easier to find a pathway, for linear-shaped facilities, that would minimize the creation of vegetation-free zones as a measure to protect equipments against falling trees and forest fires. Keywords: forest cover, mining projects facilities, digital models, airborne laser survey

Sep 1, 2012

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By Takeshi Nagano

Copper pyrometallurgy in Japan has experienced quite fundamental changes in last fifteen years. The severe environmental restriction coupled with increase of energy costs accelerated the development work of the new continuous process in Mitsubishi Metal Corporation. After several years of pilot plant test work the commercial plant was put into operation at Naoshima Smelter in 1974, the design capacity of which was 4,000 tonnes of copper per month. Many modifications and improvements have been incorporated into the process and 7,200 tonnes per month of copper production was achieved in 1983, proving that continuous process was much more economical than conventional process. It is now possible to design and operate the continuous process in wide range of capacity. This paper will review the process and describe the progress of the process in these 10 years. 311

Jan 1, 1985

By Euler De Souza, Kyle Penner

"Booster fans play an important role in assisting main fans by boosting the air pressure of the ventilation air passing through it. The correct placement of underground booster fans in a mine is a critical decision since it not only influences the mine’s operational capacity in terms of costs and efficiency, but also affects safety and environmental conditions. There are many booster fan installations around mines that are inappropriate, in some cases resulting in system failure (fan stall) or in a major negative impact on mine production. Inadequate booster fan placement has resulted, in some cases, in extensive air leakage which has compromised the economics of the operation and, in other cases, in recirculation of contaminants which has seriously compromised safety. This paper provides guidelines for proper design and siting of booster fans underground, to not only achieve an economic ventilation system but to create safe work conditions and efficient atmospheric conditions. Procedures for the planning, installation, operation and maintenance of booster fans are also presented. A case study illustrating the design and siting of a major booster fan installation in a potash mine, supported by computational fluid dynamics analysis, is presented.INTRODUCTIONIn large underground operations with complex ventilation networks offering high resistances, the never ending increased required quantities of air can almost only be supplied through use of high pressure main fan systems. These fans may, in effect, induce significant leakage losses in the system, having a negative impact on safety performance. In such cases, booster fans can be designed to decrease the main fan pressures and reduce the leakage flows, improve system efficiency and reduce costs. In well designed systems, booster fans can thus be used to redistribute the airflow and assist the main surface fans.When the pressure supplied by the main fans is insufficient to meet the ventilation circuit pressure requirements, booster fans are placed in strategic locations where pressure boosting is essential. Booster fans are typically sited in sections of the circuit offering high ventilation resistance and requiring this form of ventilating air motivation. Booster fans are thus required when the mine expands, and so the resistance of the ventilation network, and the primary fans no longer can supply the required pressure and flow."

Jan 1, 2019

By C. A. Mitke

During September, 1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft mere found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2, CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97", and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were tested for air circulation and air tightness and the injector mas tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering these different tests, are illustrated in the catalogue and circulars of the company. After the above tests had been made on the oxygen apparatus, the men still complained about leaky helmets. Small quantities of gas entered the helmets and could not be detected by these methods. The

Jan 1, 1914

By Christopher Mark

"Many problems in rock mechanics are limited by our imperfect knowledge of the material properties and failure mechanics of rock masses. Mining problems are somewhat unique, however, in that plenty of real world experience is generally available and can be turned into valuable experimental data. Every pillar that is developed, or stope that is mined, represents a full-scale test of a rock mechanics design. By harvesting these data, and then using the appropriate statistical techniques to interpret them, mining engineers have developed powerful design techniques that are widely used around the world. Successful empirical methods are readily accepted because they are simple, transparent, practical, and firmly tethered to reality.The author has been intimately associated with empirical design for his entire career. But where his past papers have described the application of individual techniques to specific problems, the focus of this paper is the process used to develop a successful empirical method. A six-stage process is described:1. Identification of the problem, and of the end users of the final product2. Development of a conceptual rock mechanics model, and identification of the key parameters in that model3. Identification of measures for each of the key parameters, and the development of new measures (such as rating scales) where necessary4. Data sources and data collection5. Statistical analysis6. Packaging of the final productEach of these stages has its own potential rewards and pitfalls, which will be illustrated by incidents from the author’s own experience. The ultimate goal of this paper is to provide a new and deeper appreciation for empirical techniques, as well as some guidelines and opportunities for future developers."

Jan 1, 2015

By S Lee, I Sohn

The ferrous and non-ferrous metallurgical industries have been utilising slags, fluxes and mattes for process optimisation and quality improvements at high temperatures. Understanding the fundamentals of the thermodynamics and kinetics of chemical metallurgy regarding slags, fluxes and mattes has been essential to the technological developments of these optimisation and improvements. This work will discuss how these fundamentals have been studied in the reactions involved and implemented in the ferrous industry from primary refining to continuous casting. In particular, the chemical driving forces that allow these reactions to take place and the limitations of the kinetics that require optimisation to enhance the reactions. In addition, the future research direction for slag technology innovation and the role of these fundamentals will also be described.

Jun 19, 2024