Search Documents

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By S. Uihteenmaki

Pyhasalmi is a massive sulfide orebody located in central Finland. The mine has been in operation since 1962. The flotation concentrator produces Cu, Zn, Pb and pyrite concentrates. The plant has used an on-stream analyzer for process control since 1968. The original analyzer has overlived a few generations of minicomputers, but the analytical parts are essentially unchanged. The on-stream analyzer is a critical component in plant process control system, which has made Pyhasaltni one of the pioneers in the art of computer control and optimization of flotation plants. The paper summarizes the experiences gained from the use of the high performance elemental analyzer system and the proven benefits from the use of on-stream analyzers at a complex sulfide flotation. The aging analyzer is approaching the end of its useful life. A new state of the art analyzer system is undergoing testing at Pyhasalmi.

Jan 1, 1999

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By P Mikula, B Darlington, J Graham, P Young

In underground mines experiencing dynamic events, there is an ever-present challenge to design and maintain a capable ground support system. One key component of ground support systems is surface support, which serves the essential roles of retaining failed rock and transferring forces generated by surface displacement to rock bolts or other support elements. Observations underground show that in many instances, standard mesh panels alone do not provide sufficient dynamic support to retain substantial bulking failures imposing displacement onto mesh, and in such cases Mesh straps and W-straps may be employed. Determining the performance of surface support elements proves to be difficult, with a multitude of variables at play in the underground environment. Quite comprehensive work has been completed on laboratory testing of surface support systems; however, very little work has been conducted on in situ dynamic testing of Mesh straps and W-straps. In 2019 in Western Area’s Flying Fox Mine, in situ dynamic testing was conducted on a series of Mesh straps and W-straps using Sandvik’s in situ Dynamic Test Rig (DTR). The testing regime applied impact energies from 5.1 to 15.3 kJ to Mesh straps and W-straps. The performance of the straps that did not fail was a maximum absorbed energy of 9.3 kJ and 14.2 kJ for the Mesh straps and W-straps respectively. The testing successfully demonstrated the ability of Sandvik’s DTR to test not only rock bolts, but also surface support elements, creating new testing and research possibilities. The testing also provided important design guidance data that is not practicable to obtain using laboratory dynamic testing facilities.

Nov 29, 2022

By A. O. Gapchich, T. N. Matveeva, N. K. Gromova

"Tin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. The aim of the work is an experimental study of the modification of the surface of sulfide minerals and cassiterite by stable metal-collector complexes to increase extraction of fine tin, silver, copper and other metals from complex tin ores. Triamide cyanuric acid (TCA) was studied as a thin silver flotation modifier. Thermophilic polymer with a functional group of phenylphosphine TMPPh was used as a selective flocculant. For experimental studies of the physical and chemical effects of collecting agents on the surface of minerals the following analytical techniques were used - the analytical scanning electron emission ASEM (LEO 1420VP INCA OXFORD ENERGY 350) and laser (KEYENCE VK-9700) microscopy, measurements of electrode potentials of mineral anthills by potentiometric titration, monomineral and pulp flotation. New data on formation of the adsorbed layer of DBDTC on the surface of chalcopyrite, galena and arsenopyrite were obtained, and the dimensions of the reagent films and the strength of their adsorption. The indiscriminateness of cassiterite to DBDTC ensures its selective separation into a chamber product during the flotation of sulfides. It is shown, that modification of the sulfide surface by stable complexes Me-DBDTC and Ag-TCA-TMPPh will increase the recovery of non-ferrous metals and silver into a collective sulfide concentrate and will provide a high-quality tin concentrate for flotation of tin sulfide ores.The studies were perfomed with the aid of the Russian Science Foundation (Project No. 17-17-01292).INTRODUCTIONTin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. In this regard, it seems advisable to use new varieties of flotation reagents in order to increase extraction of finely dispersed tin, silver, copper and other non-ferrous and precious metals from multi-metal tin ores (Bocharov and Ignatkina, 2007; Khanchuk etal., 2012; Wu and Zhu, 2006; Yusupov etal., 2016)."

Jan 1, 2018

By Cagri Emer

In conventional mechanical flotation cells, when the size of particles exceed a particular value, that is of the order of 100 µm for metal sulphides, the recovery of particles decline rapidly. It appears that the turbulence in the agitated vessel is sufficiently intense to rupture the forces of attraction between the particles and the bubbles, so the large particles are flung off the bubbles in the turbulent field. It has recently been suggested, that a fluidized bed would be a very favorable environment in which to contact bubbles and the particles. In a fluidized bed, particles are supported by rising flow of fluid, which separates them from each other and allows them to move freely while remaining close together. In this novel method, bubbles injected into the fluidized bed are able to rise through it, colliding with hydrophobic particles, transporting them to the top of the column where they can form a froth layer that overflows into a launder. The flow in a fluidized bed is generally slow and nonturbulent, and preliminary experiments have shown, that it is possible to collect mineral particles as large as 1 mm and coal particles as large as 5.5 mm. If the upper particle size limit can be extended, there could be significant reductions in the overall energy consumption in concentrators. Calculations show for example that if the top size for flotation could be increased from 100 µm to 400 µm, there would be a reduction in grinding energy of the order of 40%. It is therefore, important to study the mechanism of coarse particle capture in fluidized beds. In this work, the factors governing the capture rate of particles, particularly the particle and bubble size, the fluidization velocity and the superficial gas velocity have been investigated, and the results will be presented.

Sep 1, 2012

By L. Yuan, J. H. Rowland, R. A. Thomas

Hydrogen (H2 ) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system. In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, H2 concentrations in the airflow are constant, while in the full-scale experiments, increasing H2 concentrations generated as a byproduct of charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to safeguard underground miners.

By Clyde E. Williams

MUCH has been said recently concerning the depletion of the Lake Superior iron ore re- serves. Estimates given indicate a total life of the present known reserves of twenty to thirty years. Some argue that there is no need to concern ourselves about the possible depletion of the Lake Superior iron ore supply because foreign ores can be brought in to this country at a lower price than rich agglomerated ore can be produced from the lean domestic ores. Some fear, as a result of this, a displacement of the steel business from present districts to the Atlantic seaboard. Others show that foreign ores will be brought to interior points via the projected Great Lakes-St. Lawrence waterway. Others believe that the South, given better freight rates, will extend its iron and steel market into northern territory.

Jan 1, 1931

Visual computing opens the design process to a wider audience and allows rapid communication of mine plans to all stakeholders. The integration of software and hardware technologies that take advantage of a graphical environment will continue to improve both long-term and short-term mine design (Figure 1). A good design must be adaptive to respond to decision changes as the mine develops and more information becomes available. The constraints on mine design predicate careful analysis in order to operate the mine as efficiently and safely as possible.Continuous improvement in mining is assured by developing innovative technologies that target mine survey, drill and blast, modelling, short-term design and pit and stope optimisers. The design life of a mine has to be sufficiently long to ensure the mine is commercially successful, justifying the high start-up capital costs. Being able to execute a plan so that it honours the design realises the rewards of computerised mine planning and the long-term investment in data acquisition.

Sep 26, 2011

By Laurance A. Beck

Safety is the most important aspect of haul road design. Although other aspects of road installation enter decisions on design, the safety of persons using the road has to be foremost for the duration of haul road usage. Other aspects of mad design focus on minimizing truck cycle time and fitting haul roads to the long-term configuration of the mine/quarry or construction project. Roads are often installed at high gradients for a short-term goal, but the long-term benefits are easily shown with lower gradient haul roads which provide better cycle times and lower operating costs.

Jan 1, 1995

By H. F. Yancey, E. Zane

"INTRODUCTION The term ""friability"" as applied to coal may be defined as the physical property of coal which expresses its tendency to become reduced in size during handling as a result of such external forces as impact and attrition. Thus friability is a quantitative concept and property, and hence can only be defined in relative terms or in terms of measurement. Methods of measurement are difficult to formulate and apply because coal is anything but homogeneous in physical structure and chemical constitution. aMoreover, friability itself is a composite property obviously dependent upon a group of other specific characteristics such as cleavage, fracture, tenacity, hardness, and elasticity, which vary from coal to coal with change in rank and even between individual coals of the same rank. These characteristics affect the friability values of different coals to varying degrees, but this fact does not impair the usefulness of and the need for friability measurements.The amount of breakage or degradation in size that a coal suffers in mining, preparation, and subsequent handling depends upon its inherent friability and the severity of the handling treatment which it receives from the time it is taken from the bed until it reaches the consumer. The value of the coal to the producer and jobber depends in large measure upon these same factors--friability and severity of treatment—because the larger sizes still command a premium in the ordinary market. Although much has been accomplished by the coal-producing industry in minimizing the breakage of coal in mining and preparation, it is apparent that additional reductions in breakage must await further improvements in design of coal-handling equipment. Such improvements will result from more intensive investigations of the extent of breakage or degradation in size occasioned by specific mining and handling operations and the development and application of standardized methods of evaluating friability.The work described in this report was undertaken to assist in the development of standard methods for evaluating the friability of coal. Specifically, the work deals with a Comparison of the various methods previously proposed for estimating the friability of coal and coal products. This same objective is now being sought at a number of other institutions, both in the United States and Canada, by a committee of the American Society for Testing Materials. It is believed that by providing additional information concerning a property of coal pertinent to its increased usefulness, the work described will supplement and increase the useful of the data which long have been, and still are being, furnished by the bureau of Mines on the composition of coals of the United States."

Jun 1, 1933

By JOHN R. SUMAN

IT appears now that the conflict with the totalitarian states will be a long-drawn-out struggle. The course of this war up to now indicates that this may well be the first major conflict where man power has not been the vital and determining factor. Mechanized warfare has made it possible for relatively small, well-equipped groups to outmaneuver and defeat large armies which lack the necessary modern equipment. Under these circumstances, ultimate victory becomes a matter of resources and productive ability. The important question is not how many soldiers can he put into the field, but the volume and speed in producing the armaments essential to ensure a victory. The resources available to the opposing nations and the efficiency of their systems of enterprise and production will be primary factors in determining the ultimate outcome. Germany had a head start of eight years in the armament race, and it is not easy to overcome such an advantage overnight.

Jan 1, 1942

Discussion of papers with authors' written replies and closing remarks.

Jan 1, 1947

By L. Laage, R. Greur, W. Pomroy

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry, for routine ventilation calculations and mine emergency planning. This paper describes recent work by the US Bureau of Mines and Michigan Technological University to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program, and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1995

By P. Clifford

FIPR-sponsored research will playa critical role in enhancing the competitiveness of the Florida phosphate industry as ore grade declines and environmental restrictions tighten. FIPR's program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. The development of a reliable on-line analyzer and a modern process control strategy will result in improved processing efficiency. Significant improvement in overall efficiency will also be realized as the industry adopts column flotation technology. Economic acidulation of high-Insol rock will allow the industry to adopt simplified flotation flowsheets thereby reducing operating costs. Various applications of phosphogypsum would save the industry millions of dollars in constructing and closing gypsum stacks.

Jan 1, 1998

By James W. Bass

Atmospheric fluidized bed combustion (AFBC) is an improvement in coal-fired boiler design that offers several advantages over conventional boilers. AFC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling which can, in turn, increase a boiler's fuel flexibility. This report discusses, in general, AFBC technology and, in particular, progress at the 20-MW Pilot Plant built by the Tennessee Valley Authority (TVA) at its Shawnee Power Station near Paducah, Kentucky.

Jan 1, 1985

By P. Ventura

Reliability of the liquefaction analysis is based on data plotted as by piezocone, as by deep vibrocompactation monitored tests. The negative porewater pressure, re lated to hydrostatic value, recorded by piezocone, is a good marker of the absen ce of the liquefaction. Systematic measures of the ground settlements, inside the vibroinfixed steel pipe, allow to locate the liquefable strata with loose density. Experimental study of the combined soil improvement by stone columns is carry out in particular in sea bed. The interaxis of the columns for the best efficiency is valued as of the vibrocompactation, as of the drainage effects, especially during earthquake.

Jan 1, 1989

By C. J. Cutler

Metallurgical accounting for toll treatment smelters pose a number of challenges. Multiple feed stockpiles have to be accounted for as part of the monthly recovery estimation. Moreover, multiple metallurgical intermediates make up part of the in-process inventory, which also influence the monthly recovery calculation. Errors propagate from the measurements of volumes, assays, moisture fractions and bulk densities in the various material types through multiple steps up to the point where the final recovery is calculated. These errors contribute non-linearly to the variance in the final recovery estimate. This paper develops the mathematical formulation for variance propagation in toll smelting operations, including the effect of in-process inventory, assuming measurement biases have been eliminated beforehand. Operational data from a Southern African copper smelter is used for a case study. The method of propagation of variance showed that uncertainties in stockpile assays were the main contributors to variance in the recovery estimate. Variance in the volume and bulk density uncertainties contributed a secondary, yet significant, proportion to the overall recovery variance. It was determined, for the given case study, that the recovery variance depended on the calculation method used and that variance propagation via the two-product formula was smaller than recovery variances calculated via the standard recovery formula. However, the probability that the two product formula will give inaccurate (versus imprecise) results is significantly more due to the practical difficulty of equiprobable sampling of tailings streams from smelter plants (which includes materials such as slags and flue dust). Recommendations are made on how to achieve a reduction in overall uncertainty for toll treatment smelters. Keywords: metallurgical accounting, copper smelters, pyrometallurgy, variance propagation, errors, precision, sampling

Jan 1, 2006