Search Documents

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By Robert J. Evans

Capital and operating costs were estimated using a wet suppression, fabric filter, and a combination system of the two for hypothetical hard rock stone crushing plants located in central Pennsylvania, operating at 300, 600, and 1,000 tons per hour. Fixed capital expenditure for the dust abatement systems ranged from $49,129 to $249,162. Annual operating costs for the dust abatement systems ranged from $8,394 to $46,606 (0.9 to 3.2 cents per ton). If these dust abatement systems are properly sized, installed, and maintained, efficiencies approaching 95 percent can be expected for reduction in weight of dust particles emitted before control.

Jan 1, 1975

By John Cory, David Lily, Bill Hissem

The Lafarge granite quarry in Cumming, Georgia is using Principal Component Analysis (PCA) and Biplot charting to identify important variables and control air blast and vibration. Every blasting situation is unique and PCA and Biplot charting help to clarify the major variables determining air blast and vibration.

Jan 1, 2010

By K. T. Audt

The Yayoi period, from about 300 B.C. to A.O. 300, represents a time of important changes in Japanese history. During this period the advanced rice culture of the Asian continent was introduced to Japan, along with the techniques of animal husbandry, spinning, bronze casting and metal working(1) . As was the case in the Jomon period (11000 B.C. to 300 B.C.), the Yayoi period is traditionally defined by a particular type of pottery, characterized by the use of the potter's wheel and an extreme simplicity of decoration and form(2) . Pieces of this pottery were found in 1884 in a district of Tokyo, known as Yayoi-Cho, not far from Tokyo University. Within a decade the name Yayoi had come to be used for the period which also saw the first casting of metals in Japan121. During the Yayoi period, the foundation of the ancient Japanese state was laid as the individual small communities were unified and as labour specialization and social levels developed. In fact, the Yayoi may be the true ancestral culture of Japan(3) . However, the origin of the Yayoi is not definitely known. One theory indicates that the Yayoi people may have been driven from the Asian mainland (via Korea) by the dynastic wars that accompanied the unification of China under the Ch'in and Han and that these settlers rapidly displaced the Jomon. Bronze objects and the cultivation of rice may have arrived about the same time - in the third century B.C. Iron was in Japan within another century, but since it rusts badly and disintegrates, only a few small pieces are known from such an early date(4) . After about 50 B.C., the Yayoi cultures of western Japan were in fairly close and regular contact with the continent via Korea(5)

Jan 1, 1999

By William A. Beck

This paper is one of a series, describing current practice in diamond drilling for production at various mines throughout the United States. It describes the drilling and blasting methods, used at the Tennessee Copper Co., which started using deep-hole drilling for blasting in 1927, employing inde- pendent, rotation percussion drills with sectional drill steel. Since 1942 the company has employed diamond drills for deep-hole drilling. This method has now passed the experimental stage and promises to become permanent. The elimination of rock dust and safer working conditions for the drill crews are listed as the main advantages. The higher initial cost of equip- ment is the principal disadvantage.

May 1, 1948

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

The tensile test results of as-cast A356.2 grain-refined alloy castings show that the tensile strength can be improved by strontium modification (`SrM'), superheating at 900°C OM, and melt thermal treatment of the Sr-modified alloy melt (`SrMTT'). Both SrM and SrMTT processes can greatly improve the ductility (percent elongation) of the as-cast alloy. During solution heat treatment at 540°C, eutectic Si particles undergo fragmentation, spheroidization, and coarsening, thereby affecting their morphology. The effects of solution heat treatment on the tensile properties of the variously treated A356.2 alloy castings can be summed up as follows: the yield strength of the castings is significantly improved after 8 h solution heat treatment due to the precipitation of Mg2Si, after which it remains more or less the same with the further increase in solution treatment time up to 80 h; the ultimate tensile strength is also greatly improved within the first 8 h of solution heat treatment and then remains at the same level thereafter, up to 80h of solution treatment. The improvement in UTS is attributed to Mg2Si precipitation, dissolution of Si within the aluminum matrix, and changes in the Si particle morphology (spheroidization). The ductility of the as-received grain refined non-modified (`NM'), grain refined and superheated at 900°C (`SH'), and melt thermal-treated grain refined (`MTT') A356.2 alloy castings can be improved considerably with solution heat treatment e.g. from ~6% in the as-cast non-modified casting to ~10% after 80 h solution treatment.

Jan 1, 2011

By W M. Gilchrist

This paper gives an estimation of the future requirements of the western world in relation to energy re-sources. It then goes on to outline the role that atomic power -with its basic raw material, uranium -will play in supplying these energy requirements. Canada's position in this picture is covered, and some interesting forecasts are made. Introduction I T is possible that the following remarks will appear to have more to do with power than uranium. However, to fully comprehend what is in store for the Canadian uranium mining industry, we must be able to estimate the potential requirement, and, to do this satisfactorily, a thorough understanding of the circumstances that will give rise to that demand is necessary. The growing need for electrical energy will play by far the major role, as large tonnages of uranium will be required for its generation. The nuclear weapon has, up to the present, comprised the major market for uranium.

Jan 1, 1964

By Jorge Madias

Se analizan las distintas alternativas para la producción de barras de refuerzo de hormigón: endurecimiento por solución sólida (“dureza natural”); endurecimiento por temple y autorevenido en línea (Tempcore, Thermex, etc.) y endurecimiento por precipitación (microaleación con niobio, vanadio o titanio) y su influencia sobre la performance de las barras, en lo que hace a la resistencia a la corrosión, al fuego y a los sismos.

Aug 17, 2017

By J. J. Forbes

The Act of Congress authorizing the establishment of the United States Bureau of Mines became effective July 1, 1910. One of the most important duties Congress delegated to the Bureau in this Act was the study of health and safety conditions in the mineral industries. Early investigations of these conditions revealed the need of prompt Care of injured employees, as, under the difficulties inherent in their occupation, seemingly unimportant wounds if not treated promptly might become infected and cause permanent disability or even death. Many seriously injured persons brought out of mines and plants by fellow workers ignorant of approved methods of giving first aid or of safe means of transportation have been caused suffering and have had injuries accentuated to such a degree as to bring about permanent disability or death. The need of general instruction in first aid thus became apparent. BRIEF HISTORY OF FIRST-AID WORK The education of miners in the United States in first aid probably was conducted systematically first by the anthracite industry in Pennsylvania. Subsequently, first-aid training was carried on actively in Alabama and Indiana. Meanwhile, a general training campaign was carried on among industrial workers by the American Red Cross Society; when the Bureau of Mines began its nation-wide campaign of instructing employees of the mineral industries, the Red Cross turned over that part of its industrial training work to the Bureau but continued to cooperate by furnishing surgeons as judges in important first-aid contests and demonstr tions and assisted for a number of years in determining training methods.

Jan 1, 1937

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter has been developed to predict the molten temperature. The primary assumption of the model was that all matte, slag and gaseous phases in the converter were in thermal and chemical equilibrium. In this model, the matte components were considered only as copper, iron and sulfur elements. In the slag making stage, all the reacted iron was converted to fayalite. The reaction rate of iron and oxygen in this stage was considered to be constant. The converter temperature was calculated by heat balance over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depends on process parameters such as oxygen efficiency and molten emissivity.

Jan 1, 2007

By M. Faraji

Inclusions formed in a high-carbon, manganese-silicon killed plain steel (Fe-0.77C wt%) were studied. Various techniques were used to characterise the inclusions, and the latter were classified according to their chemical composition, size and morphology. The main constituent elements entering the inclusions were Mn, S, Al, and oxygen. Alongside MnS and some Al2O3 inclusions many non-metallic inclusions appeared in complex forms, consisting of silicates, sulphides and oxides. Duplex oxy-sulphides, mainly MnS combined with Al2O3, or SiO2 were the most common complex multiphase inclusions in this steel. The nanoindentation technique was used to assess and rate different types of inclusions and data of the hardness and elastic modulus of individual inclusions at room temperature are presented.

Jan 1, 2010

By M. T. Baquera

A comparison of microstructures associated with W single-crystal ([001], [011], [111]) rods prior to deformation (as grown), and after quasi-static compression (at a strain rate of ~1/s) by transmission electron microscopy (TEM) shows several orders of magnitude difference in dislocation density. Dislocation substructures were not significantly different amongst the deformed sample orientations. In contrast, [001] W rods penetrated into steel targets, at impact velocities of ~1.3 km/s, exhibited heavy dislocation densities and dynamic recrystallization as very distinct microstructural regimes accommodating the penetration process. Twinning on {112} also occurred as a precursor to, or remnant of, these microstructures near the projectile head. These results suggest that deformation accommodating the extreme strains and strain rates associated with the penetration of a single-crystal rod into a metal target is not adequately represented by conventional deformation

Jan 1, 2006

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By Marius S. Darrow, William B. White, Rustum Roy

The PbS-PbTe systen has been studied by quench-ing and D.T.A. techniques f?om 400' to 1150°C. Runs were made in evacuated silica tubes so that all equilibria are at the vapor pressure of the system. Lattice parameters of the quenched salnples , measured by X-ray diffraction, show a complete crystalline-solution series existing over a narrow temperature range between approximately 805" and 871°C. An exsolution dome extends from a maximum of about 805"C (approximately 30 mole pct PbTe) to 1 and 96.5 pet PbTe at 400°C. A narrow melting region, deternined by D.T.A., extends form 918c (mp PbTe), The shapes of the liquides and solidus curves imply the existence of a minimum at 871°C at approximately 65 pct PbTe. THe exact composition of the minimum could not be established due to the very narrow two-phase region. At compositions containing less than 50 pet PbTe, liquidus temperatures begin to increase, while the solidus remains almost flat to about 15 mole pet PbTe before beginning to vise toward the mp of PbS (1075 C). LEAD sulfide and lead telluride are isostructural (NaC1 type) semiconductors whose electrical and optical properties have been extensively studied and used in recent years. If appreciable crystalline solution exists between these compounds, the variation of physical properties with composition could be of interest. The purpose of this investigation was to determine the extent, if any. of crystalline solution, and to obtain the phase diagram for the system. To the knowledge of the authors, only three studies of the system PbS-PbTe have been reported, and, in chronological order, each investigation found an increasing amount of crystalline solution. In 1956, Yamamoto reported finding no evidence of crystalline solution between the compounds. Sindeyeva and Godov-ikov,' in 1959, found very limited crystalline solution. but only under conditions of excess tellurium concentration. Finally Melevski s3 investigation in 1963 indicated that one solid phase exists in the region from PbS to 7 pct PbTe and from 82 pct PbTe to PbTe at 886'C, with an eutectic at 55 pct PbTe at that temperature. Detailed data on the solvus boundary were not given. EXPERIMENTAL EQUIPMENT AND MATERIALS Commercially produced PbTe and PbS powders were used as starting materials. Batches of specific mole percent composition were accurately weighed and mixed in a plastic bottle, in a shaker mill. An analy- sis of impurity content is given in Table I for pure PbS and PbTe and for two randomly selected batches after the powders were mixed. Individual samples, ranging in weight from 0.2 to 0.5 g, were sealed in evacuated silica tubes which had been thoroughly washed and rinsed with acetone and distilled water. Thus all data taken were at the pressure of the system. Subsolidus relations were studied down to 400°C by heating the samples in a vertical tube furnace for 24 hr. The sealed tubes were quenched in water with quench time from the hot zone not exceeding 1 sec. Temperatures were measured by a chromel-alumel thermocouple and controlled to 53°C for most runs. The number and composition of phases present were determined from powder X-ray diffraction patterns taken at room temperature on a Norelco diffractome-ter, using silicon as an external standard. Above 850°C quenching techniques were, in general, found to be unsatisfactory, and differential thermal analysis (D.T.A.) was used to determine melting relations. The evacuated tubes were recessed about 1 cm at one end to accommodate the differential thermocouple. Al203 was used as the reference material in a similar tube containing the other side of the differential couple. For temperature measurements, a separate thermocouple was placed in the recess of the tube containing the sample to be measured, thus providing an opportunity to obtain thermal, as well as differential, analysis. All thermocouples for these measurements were Pt-Pt 10 pct Rh. Temperature and differential curves were recorded separately on synchronized strip-chart recorders. Thermocouples and recording equipment were calibrated using NaCl and gold standards, using the melting points 801" and 1063 C, respectively, which span most of the temperature range of interest. Heating and cooling rates generally were from 4 to 7°C per min. It was found, in fact. that rates ranging from 1.5 to 25°C per min did not significantly change the data obtained.

Jan 1, 1967

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By Larry Hopkins

The molten metal circulation pump has become a staple for melting aluminum in reverberatory furnaces. The forced convection that is created in the melt efficiently provides circulation while dramatically improving melt rates, lowering fuel consumption, extending refractory life, and providing metallurgical homogeneity. Two metallurgical guidelines that are important to many casthouses are molten metal inclusion levels and hydrogen gas content. In order to improve molten metal quality, furnace and casting practices must 'manage these molten metal defects, Today specialized in-line degassing and filtration equipment is used downstream of the furnace to accomplish these tasks. In contrast, the molten metal gas injection pump has metallurgical contact time in the process for hours during the charging/homogenization cycle. The qualitative benefits of employing a gas injection pump to "pre-clean" are outlined and discussed against historical empirical information obtained with alternate methods. Further, a recent study quantifies the merits of this gas injection technique as an effective molten metal quality improvement tool. Specifically, the effects on inclusion level as determined by PoDFA?, gas content as determined by A1SCAN? sampling and alkali metal content as determined by spectrographic analysis are examined in relationship to various gas feed compositions and flow rates.

Jan 1, 1995

By William G. Pariseau, Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"This contribution describes development and application of a user-friendly finite element program, UT3PC, to address three important problems in underground coal mine design: (1) safety of main entries, (2) barrier pillar size needed for entry protection, and (3) safety of bleeder entries during the advance of an adjacent longwall panel. While the finite element method is by far the most popular engineering design tool of the digital age, widespread use by the mining community has been impeded by the relatively high cost of and the need for lengthy specialized training in numerical methods. Implementation of UT3PC overcomes these impediments in three easy steps: First, a material properties file is prepared for the considered site. Next, mesh generation is automatic through an interactive process. A third and last step is simply execution of the program. Examples using data from several western coal mines illustrate the ease of using the application for analysis of main entries, barrier pillars, and bleeder entry safety.INTRODUCTIONRational design of safe underground entries and crosscuts, barrier pillars, and bleeder entries begins with a site-specific analysis of stress. An analysis of stress identifies the critical regions of high-stress concentration where yielding is likely and additional or more focused ground control measures are needed. This analysis also identifies regions where stress concentration is low, and risk mitigation is less urgent. Displacements induced by mining, including roof sag, floor heave, and pillar squeeze, are also of importance to stability. The popular finite element method is well-suited for such analysis and has been in use for studying coal mine engineering problems since the late 1960s (Dahl, 1969). The method has been taught in undergraduate engineering curricula for many years and offers an alternative to existing design procedures based mostly on rules of thumb, empirical methods based on mine data, and predigital-age concepts of strata mechanics. However, despite the versatility of the finite element method, usage has been limited, mainly because of the cost of the software and the required training in numerical methods.The program UT3PC (Pariseau, 2017) has evolved from early two-dimensional versions in the era of mainframe computers. These early versions were still quite limited using only a few hundred elements that required overnight turnaround times. Recent versions of UT3PC are convenient and efficient desktop programs that use several million elements. With the advent of personal computers in the mid-1980s and subsequent increase in computer speed, expanded memory, and lower costs, applications for mining increased in three-way cooperative projects among industry, the former U.S. Bureau of Mines, and academia. The Spokane Research Center of the U.S. Bureau of Mines, in cooperation with the University of Utah, developed a two-dimensional desktop finite element program, UT2PC, available to the mining community in 1991. This was a short course offered at the 1991 SME Annual Meeting in Denver, CO."

Jan 1, 2017

By Flavio Rojos-Tapia, Samuel Sánchez-Pino, Marcelo Fernández-García, Samuel Sánchez-Baquedano, Rainer M. Imhof

"Pneumatic flotation was introduced to the Chilean copper mining industry in 1993 by Ingeniería de Minerales S.A., being implementation in 1994/95. The technology is based on the designs and development of Dr. Rainer Imhof from Germany and from Chilean copper processing experience.Pneumatic flotation has been successfully used for sulphide and oxide copper minerals and copper slag, iron ores (reverse flotation), gold and promising results with molybdenum as product. Extremely hard conditions were applied in flotation process such as roughing, cleaning, scavenging. Pneumatic flotation can be applied for any type of mineral which has to be separated by flotation. Even very dense and heavy slurries can be processed, the range of the particle sizes to be collected is very wide, and the number of cleaning stages needed normally is one in our experience until now.The good performance of the technique can be explained by the high gas hold-up and the very effective micro-turbulences which boosts the attachment to the bubbles changing dramatically the flotation time concept. Some economic high lights are: less energy consumption, less maintenance costs, simple and reliable to operate and it is required a small area to install the circuits.As a result of the Chilean mining industry experience, it can be concluded that the pneumatic flotation can be regarded as an excellent alternative to the conventional way of Mineral Processing.INTRODUCTIONDerived from seventies, works in Germany about pneumatic flotation with Prof. Simonis (Technical University of Berlin) and Prof. Bahr (Technical University of Clausthal), it has been developed an interesting flotation technology in Mineral Processing, with the designs developed by Dr. Rainer Imhof, who has been known for more than ten years (Imhof, 1998) by his contribution at Ekof, KHD, Allmineral and the actual company Maelgwyn Mineral Services where he is a Technical Director. Ingeniería de Minerales S.A. has been working ten years deeply involved with the technology developed by Dr. Imhof and is more than ten years experienced with pneumatic flotation, from Wits University and Mintek in South Africa (Sánchez, 1990), (Sánchez, 1990)."

Jan 1, 2003

By Abraham Lindo

Taboguilla is a small island located 10 miles outside the Panama Canal Pacific Entrance. In 2002 a fuel distribution facility was installed in order to supply fuel to vessels passing thru the canal. The current capacity of the tank farm is equivalent to 1,100,000 barrels. The demand for marine diesel at this location still exceeds the current capacity, thus an expansion project is currently underway to increase the available space for diesel tanks. There is a total of 800,000 cubic meters to be excavated in order to create the new space. 400,000 cubic meters of that total is basalt rock which will need to be blasted

Jan 1, 2011