Search Documents

By W. E. Robinson

A laboratory study wan made to determine whether drying and preheating Colorado oil shale with waste retort gases has any appreciable effect on its oil yield. Samples of crushed oil shale were heated at subretorting temperatures in a specially constructed electric furnace by gases similar in composition to waste gases from oil-shale retorts. The results of this study showed that preheating oil shale with nitrogen or a reducing mixture had no effect upon the oil or water yield. However, oxygen in the preheating gas caused a decrease of oil and an increase of water. In general, the oil yield decreased with (1) increase in oxygen content of the heating gases, (2) increase in temperature of the heating gas, (3) increase in heating time, and (4) decrease in the particle size of tho shale. The decrease in oil and the increase in water resulting from preheating were due to oxidation of the benzene-insoluble organic material (kerogen) rather than to oxidation of the benzene-soluble organic material (natural bitumen) in the shale, A small amount of oil was volatilized during preheating, which would constitute an additional loss if prober precautions were not taken to recover it. The results obtained in this laboratory study indicate that oil shale can be preheated without appreciable decrease in oil yield by proper selection of preheating conditions.

Jan 1, 1951

By William H. Wiese

Anecdotal reports of high rates of congenital malformations and spontaneous abortions at the Shiprock Indian Health Service Hospital in San Juan County, New Mexico prompted an interview survey, obtaining data from families of 26 former uranium miners and 30 controls. Results supported the possibility of increased fetal wastage and congenital malformations. However, definitive conclusions were obviated by methodologic limitations in terms of selection of cases and controls and interviewing technique, as well as very low numbers and lack of statistical significance. The Council of Environmental Quality (1980) published a report which singled out San Juan County, nationally, as having an extra-ordinary high rate of congenital anomalies reported from birth certificates in the years 1973-75. San Juan County is in the northwest corner of New Mexico and includes the northeastern edge of the Navajo Indian Reservation. It has been the site of uranium mining and milling and also of coal mining (Clement Associates, 1980). While much attention has been focused on lung cancer and chronic lung disease as health hazards to uranium miners, virtually no attention has been focused upon possible reproductive effects that may result from exposure to radiation. Could these reports indicate such an additional arena of health effect either on miners or on others living in the vicinity of the mines and mills? The biologic and epidemiologic literature does not lend much support for adverse genetic outcome. The UNSCEAR report (UNSCEAR, 1977) summarizes much of the existing data. For example, on the basis of many animal studies and what has been observed in atom bomb survivers in Japan, it has been estimated that mutation rates resulting from low LET radiation to paternal germ cells would be 60 X 10-6 recessive and 20 X 10-6 dominant mutations per gamete per rad. There would be a five-fold increase in the number of recognizable abortions. The doubling dose for genetic disorders in mice is estimated at 100 rads. The assumption has been that low levels of exposure, such as might be received occupationally from uranium mines and mills or environmentally will produce reproductive effects that would defy distinction from background rates. However, the possibility can not be dismissed. In man, spermatogonia are thought to be three-fold more sensitive than in the mouse. Also, the high LET radiation from alpha particles is as much as 20-fold more effective in inducing changes in meiotic and post meiotic stages of cells, compared with low LET radiation. There is some degree of localization of alpha emitters in testicular tissue after inhalation of radon and radon daughters (Blanchard, R.L. and Moore, J.B., 1971; Pohl, E., 1964). The slopes of doseeffect curves are affected by type radiation and rate of administration. Data on such curves are poorly defined and debated as to whether there may be increased or decreased effect per unit dose at low levels of high LET radiation. Increased rates of aberrations of chromosomes in peripheral lymphocytes cultured from uranium miners have been reported (Brandom, W.F., et al., 1978). At cumulative exposures of 100 working level months (WLM) or less, a range of exposure lower than the limit of current occupational standards, the aberrations were increased more than two-fold. Our interest has led us to pursue the question of reproductive effects along three separate paths of inquiry: studies of the secondary sex ratio, cytogenetic study of human sperm, and studies of rates of congenital anomalies. I will present the thrust of our findings, most of which remain preliminary, comment on their interpretation and limitations, and indicate directions needed for future research. The secondary sex ratio is the ratio of males to females at birth. In the U.S., the ratio averages around 1.05. Ratios in blacks are somewhat lower (1.025) than in whites (1.053). For American Indians, the data are less definite. Values from Oklahoma and California are similar to whites (1.05). Southwestern tribes have, as we shall see, varying levels. The theoretical effects on sex ratio resulting from irradiation of the zygote are based on the principles of sex-linked genetics, including differential effects of lethal dominant and recessive mutations on the sex chromosomes, complicated by possible non-disjunctional events. Observations have done little to clarify, confirm or refute the theories. The sex ratio of progeny of survivers of the atomic bomb showed little change (Schull, W.J., Otake, M., and Neel, J.V., 1981). Observations in children of uranium miners having been inconsistent. Most frequently cited is a study of miners in Czechoslovakia (Müller, C., Razicka, L., and Bakstein, J., 1967). Compared with children born to miners prior to the start of mining, the sex ratios of children born after the start of mining were decreased -statistically significant after correcting for birth order. The ratios in first-born children were, before the start of mining, 1.118, and, after the start of mining, .713. In the interview survey at Shiprock, the sex ratio in families of non-miners was 1.03, and in families of miners it was 0.73 (p < .05). Dr. Alan Goodman at the University of New Mexico has studied trends in the sex ratio in the general population in New Mexico and Arizona with particular reference to counties in the Four Corners area and the Navajo Indian Reservation, areas where uranium mining has been active_ His findings (unpublished) are as follows: (1) Beginning in the early 1950&apos;s, there has been a modest, but persistant and statistically significant decline in the secondary sex ratio for the state of New Mexico compared with the U.S., a decline that roughly parallels the emergence of uranium mining in the Grants mineral belt in northwestern New Mexico. (2) Data available for the 11 years since 1969 show that among the five counties with ratios significantly lower than the state

Jan 1, 1981

By Yi Luo

Simulation of the multi-entry and multi-crosscut (MEMC) ventilation systems commonly employed in U .S. underground coal mines can be very tedious, due to the large number of crosscuts with stoppings to be represented in the network models. In order to reduce the amount of work needed to build the models, a common practice is to represent a number of crosscuts with one equivalent airway. However, this introduces certain errors into the simulation results. In this paper, algorithms have been proposed to simplify the ventilation networks of common MEMC systems encountered in panel development operations. The algorithms can be used to reduce a MEMC system into one airway with an equivalent resistance and to determine the airflow distributions in the system and the leakages through the stoppings.

Jan 1, 2011

By C. T. Holland

Coal mining has been an important industry in the Appalachian area for many years. This is particularly true in the northern part of the area, namely, in Pennsylvania, West Virginia, and Ohio. Also, in the south a great deal of mining activity has been carried on in Alabama, Kentucky, and southwest Virginia. Some of the by-products of this activity has been the production of mineralized water from the mines in copious quantitites. The southern Appalachians have been somewhat more fortunate in that the water there has had a considerable amount of alkalinity in it, which has to a large extent eliminated some of the more undesirable aspects of mine drainage. Northern Appalachia, including central and western Pennsylvania, the Monongahela basin in West Virginia, and the Appalachian area in eastern Ohio have not been so fortunate in that coals in those areas and the top and bottom rock have, in many cases, shown considerable quantities of pyrite, and the water does not carry the carbonates found farther south.

Jan 1, 1969

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-&apos; in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.&apos; The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By Diómedes Sarmiento

Centromin is a Mining Company owned by the peruvian government. It&apos;s considered as one of the major mining and metallurgical center in Latin America. The main operations of the Company are: Mining, Concentration, Smelting and Refining of several metals (Figure 1). At present, dentromin operates with six mining units: Cerro de Pasco, Morococha, Casapalca, San Cristobal, Yauricocha and Cobriza; which are located in the Central part of the country between 2 100 m and up to 4 800 m above sea level. The installed capacity of concentration all together ranges about 14 000 tons per day. There&apos;s also a metallurgical plant in La Oroya with a production capacity of 220 000 tons per year of refined metal. The production of the Company is diversified in twenty two (22) final pro- ducts, whose major productions are : copper, lead, zinc, silver, gold, tungg ten and bismuth. The minor products are: arsenic, antimony, cadmiun, teluriun, sulphuric acid, indium, selenium, etc.

Jan 1, 1979

By F. Mielli

Mine operation managers are constantly tasked with identifying new ways to produce more, while using less. Mine effectiveness and reliability is the foundation of improving operational performance. Timely decisions need to be made in order to identify production waste. Intelligent data needs to be visualized in real-time. Operational events need to be captured with impacts quantified and root causes identified. Unfortunately, complex information technology solutions often have a very poor success rate, with some reports suggesting 30 percent of complex projects are canceled before completion.

Feb 27, 2013

Valuers of mineral properties should be aware that accountants are a major user of their opinions of value. Reliance by accountants can range from obtaining comfort that book values in balance sheets are not overstated to establishing values by which to assess the fairness of a takeover offer. Accountants using mineral property valuations clearly can&apos;t be expected to have the same level of expertise as the valuer and ""second guess"" the valuation. But they do have an obligation, under the ASC guidelines and their own professional standards, to&apos;check the logic and reasonableness of the valuation before being able to rely on it. This means reviewing the valuation report for general sensibility, discussing the methodologies and assumptions with the valuer and being satisfied as to his competence and independence. This paper outlines how accountants use mineral property valuations, the level of scrutiny applied to such valuations and the problems commonly encountered in practice by accountants seeking to rely on them. The paper also explains how values of-mineral properties are established in company balance sheets and why these often differ, quite validly, from fair market values.

Jan 1, 1994

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By M. Sharafodin, A. A. Hassanipak

Abstract - The essential aims of additional borehole drilling are to improve the reliability of grade and tonnage estimates in each reserve class and to increase ore tonnages. The "GET" function presented in this paper considers strategies for achieving both of these goals simultaneously, and therefore is advantageous for selecting sites for additional boreholes. The "GET" function is either a linear or a non-linear product of three variables G, E, and T: f(G,E,T,) = G??E??T??where the values of any or all of the exponents ?, ?, and ??may differ from unity at the discretion of the user. G and E are the average estimated block grade and the average estimation error for ore blocks in one vertical column, and T is the compounded ore thickness within the column. To illustrate its utility, the GET function has been used for determination of the most advantageous sites for additional drilling in the Shah-Kuh Pb-Zn deposit in west central Iran.

Jan 1, 2004

By Ayman Tawadrous, Hendrik Botha, Simon St J Tose

The early miners and their mules always had the challenge of transporting unstable dynamite underground. The modern pumpable explosives, whilst far safer, still present a major logistics challenge for the mobile charging units (MCU). The challenge today is the efficient explosive delivery into declines, ramps, and vertical shafts, often requiring the MCUs to travel excess distances up and down to surface to re-load. Alternatively, the management of cassettes or ISO containers is utilized to deliver the pumpable base emulsion to the MCUs at the working face. Additionally, local laws and regulations regarding shaft clearance further compound the task and result in pausing other operations in the shaft or decline or ramp until the completion of the explosive transport. This paper examines the research & development challenges of dropping base emulsion down a vertical pipe to depths in excess of 1000 m (3280 ft.), either to an underground storage or directly into the MCU, depending on the depth. The boreholes (with pipes) are drilled in close proximity to the underground work areas. The paper also discusses the rheology of the emulsion within these vertical pipes as well as the economic benefits of such an innovative system. The learnings gained from this work, along with examples demonstrating the significant reduction in MCU travel and the safety benefits, are presented for the industry to consider moving forward.

Jan 21, 2025

By Shaoxian Song, Shouci Lu, Jingyon Gou, Pan Yiuwen

The calculated potential energies of interaction between hydrophobic particle of three minerals (rhodochrosite, quartz and talc) and air bubble show that the energy of hydrophobic interaction is the dominant factor for their attachment. An attachment rate equation, integrating particle -bubble collision and adhesion by introducing a "capture efficiency", has been put forward. It was found that the hydrophobic particle-bubble aggregates can not be disconnected in the bulk zone of flotation cell, whereas in the impeller zone the breakup may occur, particularly for the coarser particles captured by bubble. Finally, the flotation rate constant was estimated theoretically and verified by experiments.

Jan 1, 1995

By W. G. Deeks

CANADIANS are world leaders in marketing metal and mineral products. Noranda Sales Corporation Ltd. is an international metal and mineral product marketing company operating from Toronto and London, England, where it operates a wholly owned sales subsidiary and is a 50% partner in Rudolf Wolff and Company Ltd., a charter member and the largest metal broker on the London Metal Exchange. Noranda Sales employs 97 people, of whom 52 are university trained and professionally competent in international resource product marketing. We market for 19 companies or divisions in the Noranda Group and 39 companies for whom we act as agent, consultant and purchaser of resource production. Our business in 1976 was 1.5 billion dollars carried out in 45 countries and covering 24 products and materials. Today, ownership of most of the mining industry in Canada has transferred back to Canadians, and this is said with the knowledge that a significant part of the Canadian industry has been Canadian owned and managed from its very early days. Noranda Mines Limited is such an example. It was born in 1922 as the result of a copper-gold showing at Noranda, Quebec, discovered by Ed Horne, a prospector, financed with a grubstake by a syndicate mainly composed of New York businessmen. Shortly after the discovery, when the shares of the company had risen, the syndicate was sold to Canadian interests and, since that time, Noranda has been dominantly Canadian owned and certainly Canadian managed. Today, over 90% of Noranda&apos;s shareholders are Canadian, who hold an equivalent percentage of the stock.

Jan 1, 1977

By Joseph Chalmers

[Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the ?gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ulti¬mate recovery of oil from their properties. A number of factors influence the efficiency of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity shrew a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis5 expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate ofg;as injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.]

Jan 1, 1930

By A G. Dempster, N Barnett, J Oh, S Saydam

NASA’s Artemis III mission is expected to return astronauts to the surface to explore and sample the lunar volatiles by 2026. These volatiles are anticipated to provide scientific insights as to how the Moon was created and economic value to off-Earth operations. These same volatiles can pose health implications to astronauts and Earth based personnel handling lunar regolith samples. Using Australian, USA and NASA airborne contaminant exposure limits and the Lunar CRater Observation and Sensing Satellite (LCROSS) measurements of lunar volatiles in the Cabeus crater ejecta, the minimum mass of lunar regolith that can be safely handled by humans on Earth and in spacecraft can be calculated. This analysis determined a 0.15 grams pure sample of Cabeus crater regolith within a cubic metre of air has enough volatiles to exceed safe working conditions, and 14.9 grams of pure Cabeus crater regolith per cubic metre of air can impact human life. The intent of this analysis is to assist safe handling and exposure calculations for the safe handling procedures of lunar regolith containing volatiles.

Sep 1, 2024

By James L. Austing, Allen J. Tulis, Ronald Pape, Ronald G. Draftz

In a certain sense, the explosives industry began in the 13th century with the invention of black powder, which is an intimate mixture of sulfur, carbon black or charcoal, and potassium or sodium nitrate. For several centuries thereafter, black powder was the sole general purpose energetic material, serving as an igniter, propelling charge, bursting charge, and blasting agent. By today’s standards, black powder is totally inadequate for the latter three functions, but its use continues as an igniter for propellant charges because of its unique ability to ignite and burn under ambient conditions. The history of the development of black powder was reviewed by Rose (1980).

Jan 1, 1995

By A. Mikula, S. Karlhuber

"Unique physical and mechanical properties made the Pb-Sn solders attractive for low temperature joining of electronic parts. But since lead in solder materials has become a great enviromental problem and health concern, lead will be slowly replaced by other materials in soft solders. Some of these materials which are currently under investigation are ternary tin alloys. Many different physical properties like wetting behavior, electrical and thermal conductivity and surface tension are measured on these alloys, but on the thennodynamic properties and the phase diagram of the alloys under discussion there is only little information available. We investigated the (Ag, Au, Cu)-Sn-Zn systems and determined the thermodynamic properties over the whole composition range by emf-measurements. From these measurements we also got some information on the liquidus. In the Sn-rich corner the phase diagrams are still under investigation.IntroductionSoldering is technically defined as the joining of two base materials, mostly metals or metal coated nonmetallic substrates, with a third metal. The melting temperature of the third metal or metal alloy should be well below those of the substrates. Solder alloys can be categorized in soft and hard solders. Soft solder alloys usually contain lead, tin, bismuth, indium or cadmium and hard solders gold, zinc, aluminium or silicon. The difference between soft and hard solders is the melting temperature of the soldering material. This temperature is around 350°C.An interesting brief history of solders is given by Vianco and Frear [1]. They report, that in 4000 B.C. solders were already used in Mesopotamia. From archaeoligical evidence those solders were gold-based hard solders.Tin-lead soft solders and their use are not easily found, because in course of time tin has been reduced to stannic acid, making the identification quite difficult. Well preserved soft solder artifacts were discovered in King Tut's tomb dating from 1350 B.C. In ancient time Pb-Sn solders were used primarily for the manufacture and repair of cooking utensils and metal tools. The Romans used lead-tin solders extensively in the construction of the aqueducts."

Jan 1, 1996

By B. D. Thomas

When the origin and early plans, of Battelle Memorial Institute were described in this journal in October 1929 by R. W. Gillett the first director, the doors of the laboratory had just been opened and the hope of the founder that the institution serve the world by research for industry still existed only as an ideal in the minds of the thirty or so employees who then constituted the staff. Since that time the country has experienced troublous times. A devastating depression plunged the entire world into an unprecedented period of financial and industrial inactivity; and the slow recovery of the late thirties was soon to be overtaken and overwhelmed in the violence of war. Through this time of stress Battelle has continued to grow. The staff has increased to almost 600; buildings and equipment have been added, until now it stands in a place of pre-eminence in the metallurgical and engineering world.

Jan 1, 1944

By G. S. Price

This paper, which describes the milling practice at the Page concentrator of the Federal Mining and Smelting Co., is one of a series being prepared by the Bureau of Mines. The Page mine and mill are located on Silver Creek, 3 miles west of Kellogg, Idaho, and 1 mile south of United States Highway No. 10. Supplies and concentrates are hauled by truck over an automobile road which connects Highway No. 10 with the property. The concentrator has capacity to treat 300 tons of ore per day and utilizes all-flotation methods of treatment. Power is supplied from the main line of the Washington Water Power Co. which runs from Spokane, Wash., to Kellogg, Idaho. Water is obtained from the mine and also from a well which is situated 1 mile distant from the concentrator and about 600 feet in elevation below the concentrator.

Jan 1, 1932

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014