Search Documents

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By J. H. Wiggins

"The tests described below were conducted by the Bureau of Mines at a lease in Oklahoma on installations designed to decrease evaporation losses of crude oil Pram storage tanks. Use of the lease was granted by the Oklahoma Producing and Refining Corporation of America. Tankage was obtained through the courtesy of the Parkensburg Pig and Reel Co. The purpose of the installations and tests was to demonstrate the value of making crude-oil storage tanks gas-tight, rather than to determine the amount of evaporation in any one type of tank. None of the tanks used were absolutely gas-tight, but one of them was very nearly so. They comprised a tank of the ordinary open type with an 18-inch manhole, a tank with a ""4-inch vent"", a tank with a ""smaller vent"", and a tank which had only ""pin holes"" through which air and vapor could pass freely. On the last two tanks any excess pressure was taken care of by an automatic differential pressure regulator.The results obtained in these tests indicate that tight tankage will soon pay for itself. They will not, however, serve as a basis on which a producer can compute the actual number of days necessary for tight tankage to pay out, because the oil used was exceptionally volatile. It is probable that the average evaporation loss in the Mid-Continent field is at least one-half as great as that shown by these tests, and if this is true, the saving that would be effected by providing tight tankage on the lease will undoubtedly justify the expense. The installation of evaporation-proof tanks on the lease has been delayed by the failure of production managers to realize, first, that their evaporation losses are enormous, and, second, that they can practically eliminate these losses by a simple and inexpensive installation."

Apr 1, 1921

By Seung-Kyu Son, Michael T. Chandler, Youngtak Ko, Gyuha Hwang

Over the past decade, sea-floor hydrothermal vent fields have been studied by many researchers because of their commercial potential of mineral resources and the origins of Earth’s life. Approximately 300 of these are reported as massive sulfide deposits near the mid-ocean ridge, most of which are located in the Atlantic and Pacific ridges. However, only fourteen deposits have been identified in the Indian mid-ocean ridges. The Central Indian Ridge (CIR) between 8°S and 12°S is composed of three segments with a slow full- spreading rate of 33-37 mm/yr. The hydrothermal activity at the slow-spreading center can be generated along the ridge axis attended by volcanism or along the tectonic features, such as oceanic core complexes (OCCs). OCC is an exposed mantle rocks composed of peridotite and ultramafic rocks uplifted through long-lived detachment fault processes which can also lead to extensive hydrothermal circulation near the slow-spreading center. Therefore, the identification of OCC’s properties will be an important indicator for finding the sea-floor hydrothermal vents. To study hydrothermal activity of the CIR, Korea Institute of Ocean Science and Technology (KIOST) have conducted expeditions using R/V Onnuri over four years (2009-2011, 2017). High-resolution bathymetry and backscatter data was obtained during expeditions using multibeam echo system of EM120 in 2009-2011 and deep-tow side-scan sonar system of IMI-30, which has more higher resolution than EM120, in 2017. In this study, we use these high-quality data for constraining location and size of OCC. We also analyze the geophysical and morphotectonic characteristics of OCC gathering high-resolution bathymetric map and backscatter image.

Jan 1, 2018

By H. Mischo, R. Ellmies

Uranium has been mined in Namibia since the 1970s. The worldwide increasing need for energy in the early 2000s has led to the development and opening of a second uranium mine in 2007 and has triggered an increased interest in uranium exploration, often referred to as “the Namibian Uranium Rush.” In all, four mining licenses have been granted by the Namibian Government, which currently has two mines in operation, a third undertaking trial mining and the fourth in project finance negotiations. In addition, highly intensive prospecting activities at additional deposits are at an advanced stage. The finalization of the strategic environmental impact assessment (SEA) on uranium mining in 2010, the first of its kind and scale in the world, has enabled the Namibian government to assess this uranium rush and its tremendous legal, socioeconomic and environmental impacts and to prepare for the different future scenarios conceivable when this article was written in 2011, including both a skyrocketing and a complete breakdown of demand scenario. The Fukushima disaster and plans of the Namibian government to significantly increase royalties and company taxes in 2011 have threatened the market situation, forcing investors to reevaluate Namibian uranium mining projects. However, with the tax and royalty increase initiative since withdrawn, most projects are back on track at this point in time.

Jan 1, 2012

By Guo Chang Jiang

In order to improve the IIAZ toughness of X-60 pipe steel, the intragranular ferrite plate (IFP) technology was used. The characteristics of IFP is claimed to be much fine ferrite plates appear inside the original austenite grains. By means of suitable Re, Zr, Ti additions in a bath with a higher initial oxygen potential, a good control of the peak temperature and the cooling rate during welding simulation, one can get a %IFP in volume over 50%, and the toughness gets up from 55 J to 160 J. It was found that the inclusions most effective in nucleating IFP are some deformable complex silicates which either entrap Re, Zr, Ti oxides or contain these elements. The greater the number of the evenly distributed and effectively nucleating inclusions, the more the %IFP in volume, and the finer the microstructure of the HAZ, so the better the relevant toughness. Generally, these silicates bahave as fine spheres along a line. The present authors revealed that these fine spheres result from the remelting of the shuttle- like silicates due to heating in the process of welding simulation. These silicates used to get a higher sulphur capacity, so MnS deposits might be observed on the periphery of the silicates. IFP was proved to be directly rooted in the [Mn] depleting zone which locates beside MnS deposits.

Jan 1, 1997

By William J. Purdy

Successful design, operation and completion of a surface waste management facility for a diamond mine located in Canada?s northern environment requires careful planning to minimize short and long term environmental impacts. As part of the mine development application process, best practice standards were applied using conventional engineering to reduce the environmental effects of the mine waste facility at the Snap Lake Diamond Project. This paper presents the design criteria, site conditions, material characteristics and engineering management objectives considered for optimization of the development plan. Insight into the engineering analyses, development alternatives, monitoring program and reclamation strategy plan to be undertaken during mine operations to provide opportunity for adaptive management and to minimize environmental impacts is provided.

May 1, 2004

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022

By R. P. Alger, C. A. Doh, M. P. Tixier

The principle, the equipment and field operation of sonic logging are described. The tfio-receiver system produces logs independent of hole size and mud. Field experience is given and forms the basis for the interpretation of the log. The derivaiion of porosity values from measured velocities is discussed, according to the type of formations (hard formations, compacted sands, and unconsolidated formations). The time-average equation proposed by M. R. J. Wyllie, A. R. Gregory and L. W. Gardner is uscd as a basis for the computation of porosity in limestones, cemented sandstones and compacted sands. Variations in the lithologic character of limestones do not seem to change the porosity calibration markedly. The compaction of sands is related to the compaction of shale adjacent to them; and, thus, the shale velocity is used for the establishtnent of empirical relations for the computation of porosity in un-consolidated formations. Various forrnu.las are tentatively presented to account for shale and fluid content. Field experience demonstrates that considerable attenuation of sonic energy takes place in unconsolidated formations, particularly when gas bearing, and in fractrured formations. Unusually large attenuation produces skipped cycles, a feature easily recognized. The application of sonic logging to structura1 studies is featured, showing its possible integration with the dipmeter. Correlation and its application to the irrterpretation of seisrmic surveys are reviewed. The paper is illustrated with field examples. Sonic logging is the recording of the time required for a sound wave to traverse a definite length of formation. Sonic travel-times are inversely proportional to the speed of sound in the various formations. The speed of sound in subsurface formations depends upon the elastic properties of the rock matrix, the porosity of the formations and their fluid content and pressure. Below the "weathered" or low-velocity layer extending from 50 to 100 ft or so below the surface, sound velocities may range from about 6,000 ft/sec in shallow shales to as much as 34,000 ft/sec in dolomites. In hard formations (well cemented and/or compacted), the sonic log reflects the amount of fluid in the formations; hence, it correlates well with their porosity. In unconsolidated formations, which are usually of fairly high porosity, the sonic log gives an approach to porosity determination, when its readings are corrected for lack of compaction, shaliness, and fluid content. In such formations the sonic log may also indicate the presence of gas and may distinguish between oil- and water-bearing beds. Field experience with the sonic log in soft formations is more limited than that in hard formations. As a result, interpretation in soft formations is not as well developed at the present time. In all types of formations the sonic log is of considerable value for correlation and for the more detailed and accurate interpretation of seismic data. EQUIPMENT AND PRINCIPLE FIELD OPERATION The basic features of the sonic log" are a two-receiver system and two available short spacings. The log is recorded on film using a standard field unit. An SP curve is run along with the sonic curve to give a more interpretable log and to establish absclute depth control for comparison with other logs run in the same well. If desired, a gamma-ray curve may be recorded simultaneously with the sonic curve. Fig. 1 shows the sonic-gamma ray combination sonde. The sonic portion consists of a sound transmitter and three receivers mounted 3, 4 and 6 ft from the transmitter. When the first and second receivers are used, a sonic log of I -ft spacing (distance between receivers) is obtainea. Use of the first and third receivers provides a 3-ft spacing. The transmitter emits pulses at the rate of l0/sec. After the transmission of a pulse the first arrival of sound energy at each receiver triggers its response system. The differ-

By F. S. Hoseinian, D. Deglon, L. leal Filho, M. Safari, T. C. Souza Pinto

This paper investigates the effect of chemical and physical operational parameters on the reverse flotation of Timbopeba itabirite iron ore in a pilot-scale pneumatic flotation cell. Operational parameters include collector and depressant dosages, feed rate, superficial gas velocity and solids concentration. Results show that increasing collector dosage results in an increase in quartz recovery, particularly for the coarser quartz where recovery increases by nearly 30%. Increasing depressant dosage results in a decrease in both quartz recovery and hematite loss, for the coarser hematite particles. Increasing the feed rate has no effect on quartz recovery or hematite loss, suggesting that the pneumatic flotation cell is not residence time constrained. Increasing the superficial gas velocity results in an increase in quartz recovery to an optimum at a Jg of around 0.6 cm/s after which it decreases significantly, particularly for the coarser particles where recovery decreases by as much as 50%. Decreasing the solids concentration does not affect quartz recovery but results in significant decreases in hematite loss. Here, fine and coarse hematite loss decreases from around 25% to 12% and 10% to 2% respectively. Superficial gas velocity and solids concentration are operating parameters which have the largest effect on the flotation performance of the pneumatic flotation cell. Results suggest that this flotation cell should be operated at relatively low superficial gas velocities and solids concentrations. However, these are pilot-scale findings and would need to be tested at an industrial-scale where different operating conditions may be optimal. Keywords: Operational parameters, reverse froth flotation; entrainment; iron ore

Jan 1, 2020

By John K. Kellis, Fazley Azhar

Advancements in AC drive technology offer conveyor designers a viable drive alternative for conveyor systems which require accurate load sharing as well as multiple drive systems. Recently developed AC drives have the ability to accurately control the output torque of AC motor. These AC drives, compared to current DC drives, offer superior performance characteristics while enjoying the benefits of an AC motor. Conveyor applications and case studies incorporating this AC drive technology are presented for review.

Jan 1, 1998

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By W. J. Bennett

WHEN Dr. Horace Fraser, your President, invited me to speak to you today I advised him in confidence that I was leaving my present positions on April 30th. In the circumstances it seemed to me that this audience might prefer to have as its speaker one who wo.uld J1ave a continuing association with the atomic energy programme. Dr. Fraser was kind enough to suggest that my re-marks might he of special interest to you, since I would be able to sum up my views on the atomic energy programme. I hope that I will not disappoint him or you on that score. I am particularly pleased that my last public appearance in my present positions should be at the Annual Convention of the C.I.M. since, as all of you know, a very important part of my work has been in the mining field. As it happens, my first public address on the subject of atomic energy and its raw material -uranium -was made at your Annual Convention in Montreal in April, 1949. It seems fitting that my final address should also be made at this convention -nine years later.

Jan 1, 1958

By Steve Hicks, Zach Agioutantis, Greg Hasenfus, Zach Wedding

Most prediction methods used to calculate mining-induced subsidence rely on empirical formulations, which typically assume flat topography and uniform properties in the overburden. It is also well known that when a longwall panel mines below a valley bottom surface ground deformation magnitudes and orientations may be significantly influenced by the presence of the valley. This paper discusses ground deformation data collected at different surface locations above the Buchanan mine in the eastern United States. Measurements at individual surface points and strata movement measurements using a three-point extensometer have been collected as the area was undermined. Measurements correspond to the mining of the panel immediately under the measurement points and to the mining of adjacent panels. Measurement locations correspond to valley bottom locations. The measurements are critically evaluated and compared with respect to topography and panel face location. The issue of the fluctuation of GPS measurements is also discussed.

Jun 25, 2024

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By Fumiatsu Sato

In recent years, an increasing number of urban soil contamination cases have been found during redevelopment of former factory sites. Hydroclassification technique, separating heavily contaminated fine soil particles from contaminated sites, is one of the economical remediation techniques for contaminated soil by heavy metals, but the separated fine soil particles are generally landfilled because of the difficulty in removing strongly adsorbed heavy metals on them. In the previous study, the authors have investigated the mechanism and the optimum condition of chlorination-volatilization technique to eliminate heavy metals from inorganic waste and found it was needed to heat up around 1273K. In this paper, a new remediation technique for lead contaminated fine soil particles is proposed. This technique is composed of chlorination and subsequent warm water extraction. In the chlorination step, water-insoluble lead complex is chlorinated to be water-soluble lead chloride without volatilization, by heating the soils with MgCl2-CaCl2-KCl salt mixture at relatively low temperature. By subsequent warm water extraction, lead chloride is leached out. Effects of chlorination conditions, such as time, temperature, composition of the salt and added salt ratio, on lead behavior were investigated. It was proved that lead concentration could be reduced below Japanese environmental standard.

Jan 1, 2006

By C Itotoh, K O’Halloran, L Karlson

Global methods used to explore for minerals have progressed relatively slowly since the development of the first diamond core drill in 1863. Since then, key developments such as wireline geophysics (1920s), the tricone drill bit (1930s) and aeromagnetic surveys (1940s) all occurred in response to global events. In this project, BHP’s WAIO Geoscience operations team hypothesise that a global movement towards a greener future as well as an increasing intolerance for safety events will drive another step change in exploration methods. We have leveraged our relationships with exploration contractor partners and industry leaders to develop a realistic vision for 2033 and beyond, where drill rigs, earthworks and geophysical units are operated and maintained remotely; emissions of dust and waste are eliminated; hazardous energy sources are controlled; procurement is based on sustainability rather than cost and carbon emissions are tracked with the same rigour as production metrics. We have combined these visions into a series of graphical illustrations with the aim of inspiring ourselves, our vendors and our peers to collaborate further on producing a step change in our industry.

Sep 18, 2023

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By Carole L. B. Mitchell

The increased use of micropiles and soil nailing presents a growing database of verification and sacrificial load test data. In Washington State, the use of micropiles is becoming common, and soil nails are now almost as widely used as tiebacks; yet the state of the practice in understanding load transfer rates has not improved. This research compiles load test data for micropiles and soil nails from Shannon & Wilson?s records in the Puget Sound region of Washington. Ultimate and maximum load transfer rates for design are correlated to geologic units and soil types found in the region. Variables such as pressure versus tremie grouting, hole diameter, soil density/consistency, and the presence of groundwater are compared to load transfer rates for similar geologic units and soil types. Results are also compared to published PTI, AASHTO, and FHWA guidelines. Our results indicate that published ranges may be conservative for some soil types in the Puget Sound region, especially for micropiles. Performing verification tests to failure instead of typical verification or performance tests is needed to improve correlations and provide less conservative design load transfer rates.

Jan 1, 2006