Search Documents

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached to extract gold. The main aim is to decrease the arsenic content in processed materials and to break up the ore lattice, thus liberating the gold. Some regulations were established by authorities for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot plant testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum, arsenic is sublimated into elemental and sulfide forms. This process allows for the minimization of the negative influence on the environment, but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and it may be carried out in fluid bed furnaces.Oxidizing roasting of the concentrates in the presence of soda results in formation of water-soluble compounds and forces practically all arsenic and sulfur to remain in the cinder."

Jan 1, 2003

Coal-derived flue gases contain CO2/SO2 and these contaminants preferably have to be captured by cheap sorbents. This remediation approach is from the standpoint of addressing issues such as global warming, acid rain and development of Advanced Power Generation Systems and to realize the economic gain as well. Conventional and existing dry scrubbing technologies use regenerable sorbents which are pollutant specific and require expensive stabilizers in order to attain versatility. This paper discusses the use a novel class of sorbents prepared from the heavy metal contaminated Berkeley Pit water (Butte, Montana) by a proprietary process developed at The University of Nevada, Reno. These sorbents are activated mixed spinel ferrite (MxFe,_X04)' Preliminary experimental results show that the sorbents have good desulfurization and CO2 decomposition capacities. The decomposition effectiveness of these mixed spinel ferrites was studied at 300°C and compared against the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The results indicated that the mixed spinel ferrite had good affinity for the adsorption and decomposition. The CO2 decomposition data of both sorbents fitted the first order reaction kinetics. Even though the surface area of the magnetite was higher than that of mixed spinel ferrite, the CO2 decomposition rate of the mixed spinel ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO2 was 100% decomposed into carbon and other carbon! hydrogen compounds by the mixed spinel ferrite whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was 3-5 times more efficient than magnetite.

Jan 1, 1996

By F. R. Lee

[THE Bureau of Mines was established in July 1910 to conduct research and to Establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have a been issued since then. The lists covering all approved equipment except breathing apparatus and explosive have been consolidated info two publications: Bulletin 543, Permissible Equipment Approved to January 1, 1953, and Information Circular 5220, Permissible Mine Equipment Approved By The Bureau of Mines During 1953-62. The purpose of this publication is to supplement Bulletin 543 kind Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedules (standards) under which equipment listed herein have born approved are as follows (titles and dates of approval and revision are given in footnotes): Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 28,13 schedule 29A,14 schedule 30,15 and schedule 31.16]

Jan 1, 1966

By Sebastian Fredes, Williams Calderon, Mauricio Toledo, Gonzalo Montes-Atenas

The influence of the temperature on leaching kinetics of copper-bearing minerals has been widely acknowledged: the leaching of copper oxide ores is generally described as exothermic reactions while copper sulfide ores are associated with endothermic reactions. Reports studying the influence of temperature on leaching kinetics at laboratory scale frequently involve the implementation of either fully flooded isothermal systems or jacketed column setups. Nevertheless, at industrial scale controlling or monitoring the temperature or temperature changes is almost impractical. In fact, leaching process is usually a large tonnage operation and changing the temperature of vast amounts of material would require an enormous amount of energy and highly specific heat transfer equipment. Preliminary computations on the amount of energy required to increase the temperature of a heap or dump in 1°C indicates that it would be impossible to find an energy source able to accomplish the task. In order to provide a solution to this matter it is suggested to create an energy managing protocol (EMP) that permits heat up or down the porous body locally taking advantage from the temperature gradients and from the reactivity of different regions within the material as a function of the leaching cycles. The aim of this study is to evaluate different heat transfer regimes in a 1 ton pilot column leach operation. It was found that best results of copper recovery are obtained when heating up the column in horizontal bands starting from the top of the column moving downwards as the leach cycle evolves. The system is expected to be suitable for industrial applications, but further development of the technique is required, particularly in the design of the heat transfer dispositive.

Jan 1, 2014

By Betty J. Laswell, Gerald W. Laswell

The stepped-up pace of US open-pit and surface mining during the 1970's is a direct response by mining firms and equipment manufacturers to rising costs and declining ore grades. In the race for bigger and more efficient machines, rotary drills have emerged as the foremost leader in primary drilling at major US surface operations. At least 12 different manufacturers now offer rotary rigs in the 102- mm-diam. (4-in.) or greater blasthole size range. With capital investment for the larger units quickly approaching $1 million, the question is asked, "What's been the performance record to date of rotary drill rigs operating in North America?" To answer that question, a comprehensive study of rotary blasthole drills was conducted which qualitatively reveals various problem areas inherent in the rotary drill market and indicates some new directions for improvement.

Jan 6, 1978

By G. A. Savanick

The Bureau of Mines has designed, fabricated, and field tested a water jet cutting device capable of perforating nonmetallic well casings for the purpose of completing or stimulating in situ uranium leaching wells. The device is lowered into the wellbore, where it issues a high-velocity water jet that penetrates either a polyvinyl chloride or fiberglass casing, cement, and from 1 to 4 feet into the surrounding uraniferous sandstone. The resulting perforations allow leaching solution to pass between the sandstone and the wellbore. This report describes the water jet perforator, tells how it is used, presents cost data, and discusses the results of laboratory and field tests. The tests were designed to (1) determine the optimum operating conditions for water jet perforation, (2) assess the effects of changes in these conditions, (3) evaluate the performance of the water jet perforator under actual conditions, and (4) compare this method with other methods of well completion. These tests showed that water jet perforation is superior to conventional well completion methods for selectively achieving communication between the well-bore and adjacent sand while maintaining sand control, for restoring permeability lost through wellbore damage, for stimulating poorly performing wells for completing wells with casings that have inside diameters as small as 2 inches, and for extending the effective well diameter.

Jan 1, 1981

By D A. Williams, P J. Chapman

Constructing upstream raises with tailings is an accepted and cost-effective practice in Western Australia, where the climatic conditions are favourable, desiccation (and hence overconsolidation) occurs rapidly due to air drying and there is a perceived low seismic risk. This is in contrast to many other settings, where there is either a positive water balance, high seismicity or a combination of both. In recent times, there has been an increased focus on seismicity in areas of Australia that have historically been considered to be of low seismic risk. The increased focus is driven by two recently published documents used by tailings practitioners and increased awareness from corporate entities, particularly those with mines in high-seismicity regions such as South-East Asia and South America (particularly Chile).The increased awareness has resulted in increased rigour being applied to seismic design of tailings storage facilities (TSFs) in general, and particularly upstream-raised TSFs. This paper compares the results of a seismic stability assessment for an upstream-raised TSF located in the Goldfields region of Western Australia, which has historically been considered a low seismic area, with a seismic stability assessment carried out for a crossvalley TSF containing similar tailings but located in a high-rainfall, high-seismic setting in South-East Asia. The influence of the adopted design earthquake values on the results of the assessments and the potential impact of the maximum design earthquake (MDE) on the design approach is presented for both cases. The results indicate that although the Western Australian site is located in an area thought to have low seismic risk, the screening level analyses suggest that the MDE could result in liquefaction of the tailings materials. Not surprisingly, liquefaction was also indicated for the South-East Asian site. The outcomes of the assessment are also presented.CITATION:Chapman, P J and Williams, D A, 2015. Seismic design of upstream-raised tailings storage facilities in a semi-arid, low-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 157–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Dennis Z. F. Mraz

"Because rock salt and pot ash formations contain particles capable of elastic deformation, the material has usually been compared with various rheological models containing elastic elements. Extensive laboratory testing of salt and potash samples resulted in various theoretical conclusions based on conditions quite different from those in a deep mine. It is felt that sufficient data have now been collected from underground measurements and observations to demonstrate the inelastic behaviour of salt masses in a deep mine. The conditions in deep salt strata can be defined as near hydrostatic, because the acting pressures are very high compared to the negligible elastic limit of the salt. The pressure field and creep around the single opening is a function of its shape, size and age. The same factors, together with extraction, determine the behaviour of the mining a rea. The application of the correct analytical method in mine design can significantly improve the excavation techniques and predetermine the long-term behaviour of openings."

Jan 1, 1973

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By Emma Arakelova

?2?2 (98 %) vapour passed through a reactor at 25Pa where a Zn? target was placed at 273K- 373?. Experiments were carried out on a flow- type vacuum device. ?2?2 decomposition on Zn? surface accompanied by formation of a Zn-containing volatile complex which transferred to the gas phase, and Zn? deposited on a substrate at condensation. As the substrate, five sequentially located quartz cylinders were used at 293K- 423 K (?n). Decomposition of the Zn-containing complex on quartz substrates carried out as a first- order reaction. ?The complex decomposition constant (??) increased with the substrate temperature (?n=293 K, ??=7.05 sec-1;?n = 373 K, ?? = 87 sec-1;?n = 423 K, ?? =158 sec-1). ?The complex decomposition constant did not practically vary when the target temperature increased; the complex formation rate increased slightly.

Jan 1, 2006

By H Vigil, G. Peach

Long tunnels with only one access shaft pose many program problems for logistics, combine these with the requirement to drive directly out under the seabed for 10.2 km, and the program issues become even more challenging. The Musaimeer outfall tunnel was one such tunnel and to meet and eventually improve on the planned completion date required a complex and extensive management of all tunnel logistics required to support consistent tunneling for a two-year period. This technical paper will discuss the management issues and solutions implemented to meet the challenges of the Outfall tunnel construction.

Dec 1, 2022

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

By Read Winterburn

This study of the relationship of the accumulation and drainage of oil to the structural conditions in the Wilmington oil field is presented with the hope that the data contained herein will aid in efficient exploita-tion of other fields where similar conditions exist. It is also probable that the conditions observed in this field will enable accurate comparisons of various well-spacing programs as to efficiency of production and ultimate recovery. Formations in Wilmington Field Age Formation Thickness Lithology and Remarks Quaternary and Pleistocene. San Pedro 1000 t Fresh-water sands, gravels and clays Pliocene Upper Pico 800 t Alternating sands and silt- Stones Pliocene Middle Pico 0-200 ± Sands and siltstones Unconformity Pliocene Repetto 875-1150 Gray and green shales, silt-stones and sands at top grading to interbedded gray-ish brown shales and fine-grained sands toward bot-tom Miocene Puente 4100± Hard brown shales and sands. Sands are fine and uncon-solidated at top, becoming firmer and coarser grained toward bottom. Top por-tion contains layers of lam-inated diatomaceous shale Unconformity Schist The data included herein are not complete as to all areas and zones, being confined mostly to the area south of Anaheim Street. The sections presented are illustrative of edge-water conditions in the Terminal zone and Tar zone, but have not been extended down the structure far enough

Jan 1, 1940

By Brajendra Mishra, Himanshu Tanvar

Niobium and tantalum extraction industries heavily depend on fluoride chemistry for metal oxide production. This study concentrates on developing a fluoride-free approach utilizing alkali treatment for selective dissolution of niobium and tantalum phases. The application of microwave heating in the alkali treatment of columbite significantly reduced the processing time, providing a higher reaction rate and recovery than conventional heating. A short duration of microwave exposure (6 min) elevated the sample temperature to more than 900 °C, resulting in the rapid formation of water-soluble niobium and tantalum complex. Metal recovery from the solution was attempted through direct precipitation using guanidine carbonate as the precipitating agent, resulting in a mixed oxide product with > 90% purity. On the other hand, solvent extraction was also attempted using methyltrioctylammonium chloride as an extractant, providing a niobium oxide and tantalum-rich mixed oxide with > 98% purity as the final product.

Mar 23, 2024

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

By Robert M. Becker

The evaluation of existing rock stresses from measurements of the change in diameter of a borehole that is stress relieved by overcoring has become a common practice, The stress evaluation has been generally based ,on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium is adapted for evaluation of in situ stress from borehole deformation measurements. A consistent triaxial testing approach for determining elastic properties of the overcore is also outlined. Comparison of isotropic with anisotropic interpretations of the state of stress show that large errors in evaluation may occur if the anisotropic character of the rock is neglected.

Jan 1, 1967

By C. Don Sullivan

Paraphrasing the poetic repetition of Gertrude Stein - "Research is research, is research, is research --- ad infinitum." But research takes many forms and involves many facets. Perhaps the most simple of definitions is that attributed to the late "Boss" Kettering of General Motors who in advising a young trainee said, "Research is an intelligent effort to satisfy the curiosity of the human mind." Reclamation research is complex and requires a diversity of scientific knowledge. The overall aim of land reclamation research is directed to finding practical ways to develop efficient methods to restore mined lands to productive use, compatible with use of adjacent lands, as soon after mining as possible; and, finding practical ways to reduce or prevent damage to surrounding resource areas, which may be affected by the mining process. Research in the field of mined land reclamation is not entirely new, although in some respects we are exploring new areas each day.

Jan 1, 1967

By S. S. Todd

[The purpose of this investigation was to obtain, heat-of-formation values a four Common titanates and, to conjunction with other requisite data, to derive free-energy-of-formation values In tem peratures in the range of 1,600°-1,800° K. T ht four titanites are tricalcium ?ditanite !['a¬spheremr?raritanar( rint-tir.rniurn rill( 1 This rc rr,rt sul,rlc?nu?nIs :r },r; vinu~ hul,lrc.irse,n3i n wlti h eht-rmnnIN-ti i n c {ar.a ai?rc? pu -,csseeri (or, 11 in(c-rnxiLIic co mrc+unrls conraininL~ rir:,niurrl. 'f Lac? !1~:)mc? c?xpcrirnc'ntnl n-ut rhod w,i. rna~loycul. lic?.ats of for rn:ltion of rlre comi?c,unr4~ it 29S.N. ut re mca,urc?,l by tioItl[ion e':iIorrr)utrv, using a ctrneaR }ryrlrc,fllanric-hY rir~chlorie- ,aci l mixttrrt .is rhr c-zle~rinrrrric- fluid and rc.actic~n rtu,liura}.]

Jan 1, 1956

By J. C. van Dyk, F. B. Waanders, J. Brand, C. A. Strydom

"Underground coal gasification (UCG) is a fast-emerging, in situ mining technology that provides access to low-cost energy through the utilization of coal reserves that are currently not technically or economically exploitable by conventional mining methods.Groundwater monitoring for conventional coal mining in South Africa is well established, with SANS, ASTM, and ISO standards for the specific environment, location, and purposes. South Africa’s groundwater is a critical resource that provides environmental benefits and contributes to the well-being of the citizens and economic growth. Groundwater supplies the drinking water needs of large portions of the population, and in some rural areas it represents the only source of water for domestic use. Implementation of, and adherence to, groundwater monitoring standards are thus non-negotiable.The groundwater quality management mission, according to the Department of Water and Sanitation in South Africa, is set in the context of the water resources mission and reads as follows:‘To manage groundwater quality in an integrated and sustainable manner within the context of the NationalWater Resource Strategy and thereby to provide anadequate level of protection to groundwater resources and secure the supply of water of acceptable quality.’ (SABS, 2016).In this paper we propose fit-for-purpose groundwater monitoring standards for a commercial UCG operation. It is important to proactively prevent or minimize potential impacts on groundwater through long-term protection and monitoring plans. Scope of study / standard proposal The purpose of this paper is to set out a National Standard Proposal to emphasize groundwater monitoring as one of the five strategies of the ‘Policy and Strategy for Groundwater Quality Management in South Africa’ (Department of Water Affairs and Forestry, 2000) and to align it with the National Water Act, Act no. 36 of 1998 (Republic of South Africa, 1998).The focus of this standard is directed solely towards groundwater monitoring during underground coal gasification (UCG). Groundwater in this context refers to water as sampled from dedicated monitoring wells around the targeted site, which will include the shallow aquifer referred to as groundwater, and water flow at the level of the underground gasifier, referred to as ‘coal water’."

Oct 1, 2018

By J. R. Palmes

Three coal samples, selected out of eight with well characterized surface properties, were used in flocculation tests and synthetic mixture of coal and silica was used in the selective flocculation experiments. Coal wettability and flocculant type were found to have a strong effect on the flocculation results.

Jan 1, 1993