Search Documents

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By Gerald W. Elger

To determine the feasibility of removing nonferrous metal impurities from automobile scrap by thermal treatment in a rotary kiln, the Bureau of Mines conducted four series of tests with synthetic scrap mixtures heated at various temperatures under oxidizing and reducing conditions. The treated scrap mixtures were melted in an electric-arc furnace and cast into small ingots for impurity evaluation. Analyses showed that the ingots were essentially free of residual metal impurities except for copper. Test data indicated that in an oxidizing atmosphere the percentage of copper removed increased with treatment temperature. Percent of copper removed in a reducing atmosphere was found not to be temperature dependent. A significant finding was that copper was embrittled under some of the operating conditions and was mechanically removed by fragmentation.

Jan 1, 1968

This report is the 21st in a series summarizing research and technologic work on coal and related investigations by the Federal Bureau of Mines - the Chard of the series published on a calendar-year basis 2/ Subject publica¬tions of the Bureau during 1956 are cited, and pertinent Bureau work is described briefly. The most effective method of conserving our important coal reserves is through improved technology of production and utilization. Associated problems form the program of the Bureau.3 4 5 6/ Potential production is depend¬ent on a knowledge of the quantity and quality of the reserves, and the Bureau continues to contribute information on this subject. Many problems are being studied that relate to improvements in current production, including mining methods and health and safety measures. Preparation of mined coal is necessary for its most efficient utilization. Preparation by conventional methods is being studied, as well as the development or new methods. Fundamental studies on the structure and properties of coal are necessary to insure full advantage of the special qualities of different coals. Controlling factors in the efficient use of coal in combustion, carbonization, gasification, and direct and indirect hydrogenation of coal are being studied continuously, and new processes are being investigated. The many advances in all these fields are discussed.

Jan 1, 1959

By W. J. Fene, G. W. Grove

An important activity of the Safety Division of the Bureau of Mines , in its efforts to reduce accidents , is the safety inspection of mines . Inspections are made at the request of the operators and are not connected with the inspections by the various State departments of mines . The operating management is furnished with a confidential report of the results of the Bureau's inspections , with recommendations for elimination of the hazards found . These mine - safety inspections include a study of mining practices , conditions , and equipment and in some cases the sampling and analysis of mine air and coal dust . The Bureau of Mines has no regulatory powers , therefore the recommendations made in these reports are merely suggestions , and operators are not required to adopt them . Mine inspections are a check on safety standards , methods , and practices and are essential to any accident -prevention program . A foreman or superintendent may be sincere in his efforts to operate a mine safely and believe that he has done everything possible to attain this end . However , experience has shown that because of his familiarity with the mine and the consequent " nearness " of its various features many unsafe conditions may be , and in most cases are , overlooked ; an inspector , particularly an outsider who is trained to look for hazards , can point out the unsafe conditions overlooked by the foreman or superintendent . Some companies employ safety engineers who make regular inspections of their mines , report substandard conditions and hazards found , and make recommendations for correcting them . Unless these recommendations are carried out the inspections have little value . In making recommendations , due consideration should be given to the feasibility of carrying them out ; the management may and very often does consider a recommendation impracticable because of the

Mar 1, 1935

By G. C. RIDDELL

THE metallurgist, chemist, and physicist are blazing trails that lead far afield. Pushing on into an "Alloy Age" they see a non-ferrous era over- taking iron and steel. Delving into the nature of the physical world, they break down a supposedly indivisible element, hydrogen. Not content with terrestrial problems, they peer back along the cosmic ray into iaterstellar space, glimpsing forces that are, apparently, still busy with the task of atom-making. Mastering and organizing the material and physical, they advance steadily toward that borderland of science where the concept of matter itself seems abandoned, and force is the substance left.

Jan 1, 1930

By J. J. Bean

The development drilling program of the Copper Cities mine indicated that the molybdenum content of the ore would be about 0.011% MoS2' The molybdenum content of the Miami mine at the same time was about 0.025% MOS2' The Miami mill had a very successful molybdenum operation which used bleeder turbine steam from the Miami power plant for the steaming operation. The much lower grade of the Copper Cities ore, the absence of a source of low cost steam and the use of sodium aerofloat as the copper collector which Miami experience indicated did not respono readily to the steaming technique made very doubtful the success of a similar operation at Copper Cities. However, the relatively few pounds of copper that could be recovered from the low grade Copper Cities heads made very desirable the recovery of the molybdenwa,as a source of additional revenue. Accordingly, shortly after the Copper Cities mill began operation, a research program was instituted to develop a suitable method of molybdenum recovery. This program explored first, the successful steaming process then in use at Miami and as expected, found it unable to decompose the sodium aerofloat copper collector. The known chemical depressants were then tried without much encouragement. Finally the copper concentrate was dried, not roasted, to 2-3% mOisture and this along with sodium ferro-cyanide and cyanide resulted in sufficient copper depression that a final molybdenum concentrate containing 1.0% CU could be made. The bench scale testing was followed by pilot plant testing. Sixteen

Jan 1, 1972

By Oliver Q. Leone

Three electrorefining cells were designed to investigate various factors associated with the electrorefining of reject - grade titanium sponge . Operation of the cells provided information on cell design as well as on how design and operating variables affected the quality of the titanium product . A sodium chloride - titanium chloride electrolyte was used , and the electrolyte chambers had capacities ranging from 400 to 3,500 pounds of molten salt . Major factors investigated were electrolyte composition , temperature and useful life , effect of various cathode shapes and materials of construction , methods for removing cathode deposits , effect of current density and cell potential , and the mechanics of deposit growth and crystal morphology . One of the cells was in intermittent operation over a 4 - year period and produced 2 tons of refined titanium . A product with a hardness of 80 or less Bhn (Brinell hardness number ) was consistently and easily obtained . Some metal with a hardness of less than 60 Bhn was produced . In one of the cells in which the electrolyte was held at operating temperature with an internal heater an ac input of 25 kw maintained 3,500 pounds of electrolyte at 850 ° C , but with an external heater 35 kw was required to maintain 400 pounds at 850° C.

Jan 1, 1964

By Michael J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to in situ leach mine (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Cas a Grande mine, transmissivity fluctuations are spatially correlated suggesting that at the scale of ISLM, the hydraulic process is heterogeneous and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the simulated annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming, and uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be reevaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1993

By K. Luxbacher, D. T. Hristopulos, S. Schafrik, J. Diaz, Z. Agioutantis

Big data is generated from both surface and underground mining operations. Such data contain a wealth of information concerning safety and health in the workplace and production parameters. This paper will discuss the progress towards developing an accurate forecasting model for methane gas concentration based on the analysis of data collected from Atmospheric Monitoring Systems in underground coal mines employing time series models. Several procedures need to be applied to raw data, such as data cleaning and filtering for outlier removal, data homogenization and segmentation, and exploratory statistical analysis. The data analyzed were retrieved from two coal operations in the Eastern US. A negative correlation between barometric pressure and methane gas concentration was established, at least for certain data segments. Such correlations raise the possibility that barometric pressure data can predict variations of gas concentration in the mine. The datasets will be further investigated to establish the robustness of barometric pressure and gas concentration correlation and explore the dependence of gas concentration on other factors related to mine design and operations

Mar 2, 2022

By George A. Page, Hewitt Wilson, Vance S. Cartwright

"Purpose of InvestigationThe process of removing solid material from liquid suspensions has been studied at the Northwest Experiment Station, United States Bureau of Mines, in cooperation with the University of Washington, as part of a general program to investigate the dewatering of Pacific Northwest plastic kaolins, which is difficult by ordinary filter-pressing methods. The present paper is a progress report of the work began by Vance S. Cartwright in 1928 and continued in 1931 and 1932. Spray evaporation is believed to be valuable for the following classes or grades of clay and clay mixtures:(1) Highly colloidal, plastic-type clays, which release their mechanically attached water with difficulty; (2) clays prepared for shipment in pulverized or powdered condition; and (3) synthetic, ceramic, porcelain, and tile mixtures prepared as aqueons suspension, dried and pulverized before molding. Dilute suspensions can be dewatered by spray evaporation to produce concen-trated casting slip or plastic clay with a lower water content.The most common dewatering method used in preparing powdered kaolin for the market comprises the following steps: Reduction of the water content by filter-pressing from approximately 75 percent in the thick ""slip"" condition to about 30 percent in the condition; further reduction of the water in the filter-press cakes by heat to about 5 percent; and pulverization of the dried cakes in hammer or dust. These three steps can be simplified to a single process by spray evaporation."

Jan 1, 1935

By K. Bullock, M. Levesque, G. Lyle, D. L. Millar

ABSTRACT The options for reducing the carbon footprint of energy use in mining fall into three categories of activity: i) reducing demand, ii) improving energy utilization, and iii) adopting low carbon energy technologies. In addition to the environmental imperative, the economic case for these activities gains higher priority as the prices of electricity, gas, and liquid fuels increase. Low-carbon, energy-saving technology options that are available to mining industry companies lead to projects with return rates that must compete alongside other capital-intensive projects considered by mining company boards. Energy projects frequently involve longer payback periods and lower rates of return than those of competing bids for capital, such as new mineral property developments. For energy services companies that specialize in the financing, construction, efficient operation, and maintenance of energy projects, the same returns and payback periods can be considered acceptable or even attractive.

Jan 1, 2012

By Angus D. Campbell

Introduction In the Twentieth Annual Report of the Mcintyre Porcupine Mines, Limited, for the year ending March 31st, 1932, the General Manager, Mr. R. J. Ennis, said: "During the period under review, the plans outlined in last year's report have been completed, and all operations have been centralized in the new plant adjacent to No. 11 shaft. The new mill went into operation on May 27th and attained its rated capacity of 2,000 tons per day on November 15th. The new shops, warehouse, change-house, and general offices were occupied on December 1st, consummating the change from the old to the new plant ... "Silicosis is now definitely recognized as an industrial disease, and progresses rapidly when associated with tuberculosis. In an effort to combat its prevalence and progress, the new change-house was designed to build up the men's resistance to this and other forms of disease. It provides for a complete change from underground to street clothing, with a shower bath and solarium treatment in the interval. 'Unfortunately, in almost every goldmine, a very small percentage of the work-men are not adverse to taking some of the high-grade ore for their own purpose. This, in turn, tends to cast suspicion upon the honourable as well as the dishonorable employees. The new change-house routine discourages this practice and eliminates unjust suspicion, to the satisfaction of all concerned with the Company's operations".

Jan 1, 1933

By Mark S. Sanders

The present study was designed to explore the contribution of organizational climate and management practices to the injury experience in underground coal mines. A cross-lagged panel design was used in which miners from 22 mines completed questionnaires assessing 27 organizational climate, structure, and function dimensions on two occasions, The results strongly support the hypothesis that climate and management practice have casual effect on the incidence of disabling injuries.

Jan 1, 1976

By Vitor Guarnier Domiciano

A necessidade de melhorar as propriedades dos refratários monolíticos para resistir às condições operacionais cada vez mais severas e instáveis das casas de corrida de Alto-Forno tem sido um grande desafio para os fornecedores de refratários de maneira a garantir a segurança dos canais de corrida e sua disponibilidade para operação. Este trabalho apresenta as propriedades de novos concretos refratários Al2O3-SiC-C (aplicados por vibração ou bombeamento/projeção a úmido) desenvolvidos para resistir ao severo mecanismo de corrosão que ocorre na linha de gusa de canais principais e que exige constante atenção dos operadores das casas de corrida. Testes realizados com os novos concretos refratários em canais de corrida principais de diferentes Altos-Fornos de grande produtividade revelaram uma significativa diminuição da velocidade de desgaste do revestimento refratário na linha de gusa oferecendo uma condição operacional segura e confiável às casas de corrida.

Aug 16, 2017

By Robert D. Thomson

The Bureau of Mines has compiled coal reserve data for the United States as of January I, 1974, for bituminous and anthracite coalbeds 28 inches or more in thickness to a maximum depth of 1,000 feet and for Lignite beds 40 inches thick or greater. These data were organized by State, county, coalbed, and rank. To evaluate the reserve by sulfur content, the reserve and analytical data from the Bureau of Mines energy data bank were synthesized using computer techniques. The reserve base in the Eastern States was determined to be 202.3 billion tons. Bituminous coal accounts for the greatest reserve base: 161.5 billion tons of deep-minable coal, and 32.5 billion tons of strip-minable coal. Virtually all of the anthracite reserve base, 7.3 billion tons, is minable by underground methods. All of the lignite, 1 billion tons, is strip minable. Subbituminous coal is not significant in the Eastern United States, About 14 percent of the bituminous coal reserve base, 26.5 billion tons, contains 1.0 percent or less sulfur. About 87 percent of the anthracite reserve base, 6.3 billion tons, is low-sulfur coal.

Jan 1, 1975

By Jerin Russell

This paper presents a new instrument for real-time detection of excessively coarse material in the overflow pipes of individual hydrocyclones using a non-invasive acoustic measurement technique. The hydrocyclone is an important device used in mineral processing beneficiation circuits for classification of mineral slurries by particle size. It separates a single input stream into two output streams; an underflow of coarse particles that undergo additional grinding for further size reduction, and an overflow stream of finer particles that typically goes directly into a flotation circuit for recovery of the desired mineral. However the hydrocyclone is a major piece of equipment in the beneficiation process that has no instrumentation for directly measuring its performance. The parameters currently measured – inlet pressure, feed flow rate, feed flow density – are common to the entire hydrocyclone cluster which typically has three to twelve hydrocyclones. Thus no information is available to detect individual hydrocyclones that are operating poorly. The system described in this paper detects the presence of unwanted excessively coarse material in the overflow stream of a hydrocyclone using sensors mounted to the exterior pipe surface. It provides real-time monitoring, trending and alarming of the coarse material level. This enables operators to identify poorly performing hydrocyclones, and enables corrective action to reduce or eliminate the coarse material discharge. Improving the classification efficiency of individual hydrocyclones will improve the overall classification efficiency of a hydrocyclone cluster. This leads to less variation in the particle size distribution and slurry density in the flotation feed, which will in turn improve overall mineral recovery. The reduction of unwanted coarse material in the flotation feed reduces the accumulation of that material in flotation cells. This can lead to equipment damage, and unplanned shutdowns due to events such as blocked dart valves.

Aug 16, 2017

By Leijun Li, M. M. Mahapatra

"A three-dimensional finite element model with moving heat source was developed for pulsed-laser powder deposition (PLPD) process. Experiments were conducted to study the repair of superalloy components using the PLPD process. During the experiments, IN 625 powder was deposited on a superalloy substrate similar to IN 738. The process was modeled using three-dimensional finite element analysis. Element birth and death technique was used in the finite element model for simulating the deposition of powder layer on the substrate. A moving distributed heat source was used in the thermal model for realistic simulation of the process. Temperature dependent thermal material properties including enthalpy were used for the powder and the substrate in the transient thermal analyses. The fusion zones and peak temperature distributions of the deposits were predicted from the transient thermal analyses.IntroductionPoor weldability is a critical issue of superalloy repairing. The microstructural directionality of the superalloy components are disrupted when repaired by the fusion welding processes. Currently there is no widely accepted method to economically and reliably repair directionally solidified superalloys components. Pulsed laser powder deposition process (PLPD) is a promising repairing technique as the substrate is not severely affected by the heat source.In this study PLPD technology is used as the tool for superalloy repairing. In most of the land based turbine engines the directionally solidified nickel based superalloy similar to IN 738 [1] is used as the bucket material. The turbine engine blade tips are subjected to a combination of extreme operating conditions and corrosive environment. The tip of the nickel based turbine engine blades can be repaired using IN 625 material as suggested in the literature [1-2]. IN 625 is considered to be ductile and strong enough for the purpose of Ni based turbine engine blade tip repair[1-2]. During the present PLPD investigation, IN 625 powder was used as the deposit material on an experimental super alloy substrate similar to IN 738 superalloy used as the cast superalloy for the turbine engine blades."

Jan 1, 2012

By A. Golabchi

Building Information Modeling (BIM) is an increasingly popular method for generating and managing facility information during the life cycle of a building, ranging from facility conceptualization, through design, construction and its operational life. Organizations involved in Facility Management (FM) have the opportunity to use BIM as a knowledge repository to document evolving facility information and to support decisions made by the facility managers during the operational life of a facility. This paper demonstrates the potential of using BIM to develop algorithms that automate decision making for FM applications. The potential of utilizing BIM as an analysis tool is demonstrated through the scenario of HVAC (Heating, Ventilation, and Air Conditioning) system failure in an operating facility. In case of a typical HVAC malfunction today, facility occupants record complaints in a ticketing database maintained by the FM organization. Upon receiving notification of HVAC system failure, facility inspectors visit the location to confirm the reported failure. Upon confirmation, facility managers review building plans and specifications to develop a detailed plan of action to repair any HVAC components suspected of damage. Based on the plan of action, inspectors visit the facility to inspect and, in case of damage, repair the appropriate HVAC system components. These FM practices ? as currently implemented across the industry ? are labor intensive, time consuming, and often rely on unreliable and outdated information. To address these shortcomings, the authors propose an alternative methodology of HVAC fault detection in operational buildings. The authors implement an algorithm that leverages complaint ticket data and automates BIM to determine potentially damaged HVAC system components. Based on the list of HVAC components suspected of damage, the algorithm develops a plan of action for the facility inspectors. Finally, the authors discuss the advantages of the proposed method as well as the challenges of implementing automated BIM-enabled decision making processes in the FM industry.

Aug 1, 2013

By D. B. Taliaferro

[Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Core specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of tae subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, "connate" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and availability of oil and gas within a reservoir and in devising, efficient means for their withdrawal.]

Jan 1, 1939