Search Documents

By Joel Moskowitz, George J. Tamaro

"A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140m by 100m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations, the seam dipped below rock that is more competent. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half. The tower covering the south half of the site was topped out in 2002 and the garage levels in the north half of the site were completed in 2003.PROJECT DESCRIPTIONIn September 1999, a major investment company began the due diligence process to evaluate a property on the shore of the Hudson River in Jersey City, New Jersey for a new multi-use complex. The site offers a spectacular view of lower Manhattan directly across the river from the site of the former World Trade Center. The site, covering two city blocks, was previously occupied by manufacturing and office facilities of Colgate-Palmolive.The building footprint is approximately 140m by 100m, the southern half of which is occupied by a 260m tall office tower, shown in Fig. 1. As of this writing, design of the structure for the northern half of the site has not been finalized, but it is expected to comprise an 11-story office building. A glass-covered atrium will occupy the street that formerly separated the two blocks. As part of the due diligence process and preliminary design evaluation, alternatives were considered to accommodate various numbers of parking places, both above and below existing grade. A major consideration for below grade parking is the proximity of the Hudson River some 25m east of the east building line."

Jan 1, 2004

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

By Kurt M. Larson

Future haulage cost projections led Foster Yeoman Limited into developing a fully mobile crushing and conveying system at its Torr Works quarry in Somerset, England. The purpose-built system has an effective throughput of 2,500 tonnes/hour and features an Orenstein and Koppel (O & K) manufactured walking frame, a Fuller-Traylor type 54 X 74 TC gyratory crusher, and unique mobile conveyor modules designed and manufactured by Foster Yeoman. Used in a single-bench operation in this 6 million-tonne per annum limestone aggregate quarry, the system is fed at the production face by 2 Caterpillar 992C loading shovels. The entire system is moved on a daily basis following production face locations.

Jan 1, 1986

By George M. Lucich

This report describes a sensitive, proportional temperature controller developed by the Bureau of Mines that is useful in the temperature range from 40 to 400° C with an accuracy of ±0.10 C. A temperature controller of this kind is potentially useful for regulating temperatures in air chambers, liquid baths, furnaces, and reaction vessels, and for other applications. This instrument was developed to control the duration and temperature of the heating cycle of a charcoal-filled adsorber that is part of a special helium analyzer used by the Bureau. The controller was made from commercially available parts, and can be easily modified to provide continuous temperature control. The circuit is solid state and employs no electromechanical devices. Over a 2-year period of use as a component of the special helium analyzer, this temperature controller performed successfully and required no maintenance.

Jan 1, 1979

By W. B. Clark

IN OPERATING the Alpha mine of the Consolidated Coppermines Corp., Kimberly, Nev., it was necessary to pump out approximately 1200 gallons of waiter per minute to prevent the mine being flooded. There were three levels in the mine at which water accumulated and from which it was pumped, the 1200, 1400 and the 1800- ft. levels. At each, the pumping equipment was installed in duplicate so that if for any reason one unit was out of commission the other would be available to prevent flooding. The two centrifugal pumps at the 1200-ft. level were 600 hp. each; at the 1400-ft. level, 100 hp. each; and at the 1800-ft. level, 300 hp. each.

Jan 1, 1933

By J Jackson, E Sellers

Blasting related indices were developed to quantify variation in rock strength and structure for each stope, and for each lift of each stope, as part of a Mine to Mill study at an underground open stope mine. The indices were derived from combinations of data from underground diamond drilling because the simplifying assumptions contained in the block model prevented sufficient differentiation in rock mass characteristics to enable adjustments to the blast design.Application of combinations of blasting related indices enabled the identification of stopes with a high potential for inconsistent and oversize fragmentation, underbreak and overbreak. The indices also fragmentation outcomes to deliver increased material flow within stopes, better digability and predict indicative mill throughput. The stopes with issuesCalibration of the results enabled adjustments to the blast design based on the rock mass conditions and accordingly improved the blast outcomes. This enabled improved productivity by reducing underbreak and overbreak, having a more appropriate fragmentation, which reduces unplanned rock handling and improves bogging. The reduction in recovery drilling creates huge opportunities to improve output by reducing production delays and decreasing the overall cost per tonne. By understanding the explosive performance and blast energy distribution in relation to rock mass blastability poor, performing designs in blind upholes and convex stopes were identified.The conclusion of the work is that value improvement, regarding increased revenue and reduced costs, can be achieved across the whole underground Mine to Mill process chain by developing stope based indices from the existing geological information to correctly tailor the blast design to the rock within, and surrounding, the stope.CITATION:Jackson, J and Sellers, E, 2017. Blasting related indices as the key to underground blasting improvements in a challenging rock mass, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 23–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Krzysztof Filek, Anindya Sinha, Bernard Nowak

Taking into account the possibilities of condensation of water vapour contained in air during its flow through a series of spot coolers as well as formation of eventual fog, a mathematical model of dynamic temperature, specific humidity and degree of fogging of cooled air in underground mining galleries with direct ventilation is developed. In the gallery, there situated various heat and moisture sources both of distributive and of concentrated types. The model is represented by three partial differential equations of first order. The cases of cooling with full as well as with partial air stream flowing through the gallery are distinguished. Owing to the fact that in practical designing, more important is the knowledge of the variation process of temperature, specific humidity and fogging of cooled mine air at steady state conditions, the model is modified to a set of three nonlinear ordinary differential equations. Based on the presented algorithm, the obtained set of ordinary differential equations is numerically solved which enables to: • specify the distribution of temperature, specific humidity, relative humidity and degree of fogging of cooled air in mining galleries; • determine the cooling powers of air coolers for their known locations; • indicate the locations of the coolers of known cooling powers. Exemplary calculations of temperature and relative humidity of cooled air are presented graphically in a number of diagrams.

Jan 1, 1997

"IntroductionThe Chairman, in his speech to this body last year in Montreal, stated that the Dominion Coal Board looked to and depended upon the Bureau of Statistics for statistical material, and the Bureau does collect and publish monthly and annual data on coal. It may therefore be asked why an officer of the Dominion Coal Board should prepare and give a talk on statistics.I would explain that it has been our experience in the Board that, since the supply and consumption of coal in Canada is subject to a seasonal ebb and flow, it can be more profitably studied on the basis of a twelve-month period ending on March 31st than of a calendar year, since the end of March does represent a fairly stable end point in this ebb and flow. The figures are not prepared or published by the Bureau on that basis and it has therefore been thought that a presentation on this fiscal-year period would be of interest. The Bureau of Statistics has agreed that this may be valuable and all the data here presented are based on the reports secured from various sources by the Mining, Metallurgical and Chemical Division, Dominion Bureau of Statistics. The only contribution by either myself or the staff of the Dominion Coal Board has been the tabulation in a different twelve month period, and the comments upon the picture presented.It should be noted that the data for the month of March, 1950, are not available in all cases and consequently the figures for that year contain an estimate for this month."

Jan 1, 1950

One of the problems with mining projects is the setting of the design criteria that will best match the requirements. Normally this is expressed in economic terms but can be other factors. With massive orebodies these problems are often compounded by the general lack of distinct mining boundaries. A technique using evaluation surfaces was developed at Palabora for the underground mine design. This technique has subsequently been applied on several other mining projects to assist in the determination of the design criteria. This paper discusses the method, illustrated by some of the results of these studies.

Jan 1, 2000

By Dong-Wei Li, Tao Zhang, Diao Jiang, Zhou Wang

The feasibility of simultaneous vanadium extraction and phosphorus removal from vanadium-containing hot metal was demonstrated with laboratory experimental investigation.The effect of CaO addition on the distribution behavior of vanadium, phosphorus between basic vanadium slag and semi-steel as well as the influence of basicity on the leaching behavior of vanadium, phosphorus was particularly studied. Results show that vanadium oxidation ratio slightly decreases with the increase of basicity, but phosphorus oxidation ratio rapidly increases with the increase of basicity. The leaching of roasted vanadium slag with various CaO contents indicated that the optimal slag basicity for extracting vanadium was 1.5. The maximum leaching efficiency of vanadium could reach 84.02% and the sequence of vanadium leaching efficiency by using different leaching reagents was: 160 g/L Na2CO3 > 100 g/L NaHCO3 > 400 g/L (NH4)2CO3 > 5% H2SO4.

Mar 1, 2017

By Louis Schaarschmidt, Helmut Mischo, Ibrahim Alsalamin

In order to store high-level radioactive waste underground, the German repository concept considers clay, crystalline and salt formations as suitable host rock materials (National Citizens’ Oversight Committee, 2024). The current research projects of the Chair Underground Mining Methods at TUBAF (Technical University Bergakademie Freiberg) in nuclear waste repositories mainly focus on storage within salt formations. In this scenario, the high-level radioactive waste is supposed to be packed into specifically designed containers and then transported underground and emplaced in horizontal storage drifts. The residual temperature of the radioactive waste leads to the question if there are optimization possibilities for waste handling, the storage and the long-term emplacement of such high temperature level waste. A deeper understanding of the heat transmission from the container into the host rock might lead both towards possibly shorter surface interim storage times as well as size optimization possibilities of the repository itself. TUBAF has conducted research that successfully proved that an optimized container positioning yields more favorable thermal patterns and can be achieved with conventional mining equipment.

Feb 1, 2025

By Malcolm Ross

Fibrous minerals are common in nature but asbestiform minerals are rare. The unique mineralogical characteristic common to all the asbestos minerals is their morphologic form (or habit of crystallization) as polyfilamentous fiber bundles. The individual fibrils within the bundles have a tendency to be very long with a narrow range of diameters and grow with their long fiber axis in parallel orientation to the bundle length. The asbestiform habit imparts to the asbestos minerals sufficient flexibility and tensile strength so that most can be woven into cloth. In the past application has focused on their ability to insulate against the transfer of heat. However, these minerals possess other properties which make them useful in many industrial applications. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Asbestiform; Fibrous

Jan 1, 2007

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on’ any standard PC.

Jan 1, 1998

By E. S. Cheney

The sandstone-type uranium deposits of the Gas Hills occur in the arkosic, lower Eocene Wind River formation on the southern edge of the Wind River Basin. The d S34 values of pyrite cement associated with uranium mineralization are-significantly lighter than values for syngenetic-diagenetic pyrite nodules, therefore the H2S responsible for the precipitation of the epigenetic pyrite and uraninite was produced [t]epigenetically. These values are much lighter than the values of H2S from neighboring oil fields. The presence of biogenic pyrite in meta-igneous Precambrian cobbles indicates that these cobbles are not remnants of former; vein-type uranium deposits.

Jan 1, 1964

By H. H. Keller, E. J. Couch

Damage to production wells subjected to the high temperatures associated with in-situ combustion projects has been a problem since the advent of this thermal recovery technique. Injection of water down the annulus of hot wells has been successfully utilized for cooling and prolonging the life of such wells. A mathematical model that is suitable for predicting the effectiveness of cooling water in a particular application is developed. Typical results for practical ranges of the various parameters involved are presented. INTRODUCTION In the normal course of in-situ combustion operations, highly damaging conditions develop in the production wells as the combustion zone approaches, and these wells are subjected to high temperatures (up to 1500F). The resulting well damage is recognized as one of the more serious operating problems unique to the in-situ combustion process. Even in operations where well completions have been specifically designed to cope with this problem, the question arises as to how this destructively high temperature can be kept within tolerable limits. A simple and economical approach to this problem is to circulate cooling water down-hole. This method has been used with some success in shallow reservoirs. At greater depths, however, the heat exchange with the overburden surrounding the well and between the fluids in the tubing and the annulus tends to equalize the temperatures of the two fluid streams so that the cooling capacity delivered to the bottom of the hole decreases with well depth. This method would provide no appreciable control over the bottom-hole temperature at great depths. In order to delimit the condition under which cooling by water circulation is effective, the wellbore temperature must be related to the water inlet rate and temperature; to the reservoir depth, production rate, and initial temperature; and to the combustion at at bot tom-hole depth. A model that meets these requirements and that will offer an approach for developing engineering solutions to practical design and operating problems is described in this paper. MATHEMATICAL MODEL Previous studies of temperature distributions include those for flowing wells1p2 and those for hot fluid injection. Adams and Haddenhorst 6 presented solutions for the down-hole circulation of hot oil in the treatment of paraffin-deposition problems. In this paper the thermal model presented by Ramey 4 is adapted to the flow system shown schematically in Fig. 1. Water at temperature Ti is injected at a rate wi and flows down the annulus outside the tubing. It mixes at bottom-hole depth D with the fluids produced at race w from the hot reservoir at temperature T. This mlxtureJ. of injected water and reservoir fluids flows up the tubing and is produced at the surface at TI,. In order to describe the temperature response in this system, we make use of the usual conservation of

Jan 1, 1969

By M. B. Mirza, W. A. Sadik, B. T. Stanley

This paper presents the ventilation design for an underground testing facility in a salt medium. The under-ground workings consist of two 3.6 m-diam (12 ft-diam) watertight shafts and about 1830 m (6000 ft) of drifting. These facilities are designed to provide access for an in situ testing of a salt horizon in which a variety of hazardous and nonhazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1987

By C. L. Lin

The characterization of rare-earth resources in 3D is now possible using high-resolution X-ray microtomography (HRXMT) to describe ore texture and mineral phase composition. In addition, detailed texture analysis, including grain exposure and mineral association, can be described. Preliminary examination of a sample of Mountain Pass ore is reported to describe the spatial distribution of the mineral phases (calcite, barite and bastnaesite), particularly the grain size distribution of bastnaesite. The examination includes analysis of selected particle size classes to determine the appropriate size for liberation of the rare-earth mineral bastnaesite. Good liberation is expected to be achieved if the material is ground to a top size of -150 µm.

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By Joachim Klein, Frank Reimann

Nodular-graphite cast iron (GGG) is a material similar to steel, and one which exhibits excellent properties, in particular for components exposed to pressure. GGG cast iron has been used in many cases when sinking mine shafts with conventional tubbing. With linings made of cast iron tubbings (the backfill concrete is not integrated into the calculations, and merely serves as bedding) the properties of the cast iron can be made full use of, provided the tubbing is made to the appropriate cross-section. Calculations have shown that better static values can be arrived at when using cross-sections other than those of tubbings made to conventional German standard. The cross-sectional design of the new types of shaft lining made from GGG is to be developed on these lines irrespective of the cast iron structure being only stressed component or its restistance function being combined with the one of concrete. GGG 50 is used for the first time to make the reinforcing inner liner of a main shaft currently sunk in Germany. The physical properties of nodular-graphite cast iron, strength and deformability, suggest that, in the future, its application will not be restricted to shaft support but also in tunneling. New moulding techniques with better three-dimensional modelling resulted in new tubbing designs as installed e.g. for the Hannover underground at present. Shield-driven tunnels have to withstand earth and water pressure, apart from axial machine loads. In this field time is money as well. Therefore easy handling and quick installation are necessary for successful, use. Last but not least, safety is of first-order importance for work in shaft sinking and tunneling. Cast iron lining systems, accordingly, are adequate systems, in particular for excavations underneath water for transport systems and for goods and passengers.

Jan 1, 1987