Search Documents

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By D. W. Ashman

The zinc pressure leaching plant at Cominco's Trail Operations is now in its ninth year of production. The plant produces a zinc sulphate and jarosite slurry which is further processed in the calcine leaching circuit. Elemental sulphur, a by-product of the process, is sold in the North American market. During the past eight years, a number of changes have been made to the plant to remove known production bottlenecks and to improve leaching extraction. These changes have raised production rates above the initial design so that the plant currently accounts for approximately 20 percent of Trail s zinc production. These rates are expected to be increased further upon the completion of the alterations currently in progress. The knowledge gained over the operating life of this plant has allowed Cominco to plan for a possible future expansion of the zinc pressure leaching plant. If expanded, zinc pressure leaching would account for approximately 48 percent of cominco?s zinc production.

Jan 1, 1990

By A. C. Smith

The U.S. Bureau of Mines evaluated the effectiveness of automatic water sprinkler systems on the suppression of incipient and propagating conveyor belt fires under ventilated conditions. Large-scale experiments were performed at airflows ranging from 1.1 to 4.6 m/s. In incipient fire experiments with 100°C, standard-response sprinklers installed above and between the belts, the sprinklers activated later, the peak heat release rates were larger, and more belting was consumed at the higher airflow. In similar experiments with 74 °C, fast-response sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of belting consumed was slightly higher at the lower airflow. In incipient fire experiments with sprinklers located only above the top belt, the heat release rate and amount of belting consumed was larger at the higher airflow. The propagating fire experiments showed that sprinklers located above and between the belts were effective in stopping flame propagation. Peak heat release rates and amount of belting consumed were larger at the higher airflows for both the 74 °C, fast-response and 100 °C, standard-response sprinklers. The sprinklers were equally effective at each airflow.

Jan 1, 2010

By W. H. Miller

Introduction In this paper we have endeavoured to present a general description of the electrical applications underground at Copper Mountain, including types of equipment used, problems encountered, and methods by which they were overcome. No attempt has been made to outline in detail the wiring of various circuits. Until recent years, the main use of electrical energy underground at Copper Mountain consisted of direct current for locomotives, trolley systems, .and signal and communication circuits. The prohibitive cost of equipment and distribution systems prevented any extensive use of a.c. beyond that commonly used for essential lighting purposes. However, in 1943 the shortage of manpower and the increased cost of labour and supplies necessitated a general mechanization programme.

Jan 1, 1951

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By Suresh K. Bhatt

This U.S. Bureau of Mines report reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and under development, were investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, monorail bridge conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine research being conducted by the Bureau. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1991

By A. Tekin

In almost all branches of industry, machinery and equipment in operation cause vibration. Some sources of vibration affect only the operator’s hands, fingers, and arms, while others have adverse effects on the entire -body. Various types and numbers of machines are utilized in the mining sector, and operators with them are exposed to mechanical vibrations caused by the mining machinery they use. A field study was conducted to evaluate the vibration risks to the operators using mining machines in open pit mines. Vibration levels and whole-body vibration (WBV) measurements using various types brands, and models of construction equipment were evaluated in three different mines in the west of Turkey and compared to the the criteria specified in the EU 2002/44/EC directive and ISO 2631-1 (1997) standards. The results showed that operators using mining machinery for 8 hours were exposed to WBV levels below the EU limit (1.15 m/s2), while 44% of these operators were exposed to levels above the EU action limit (0.5 m/s2). Measurement data collected from the working environment and the recommended improvements that need to be made to reduce WBV exposures are presented.

May 2, 2022

"Many industrial processes involve materials that are subject to temperature change and thermal stress. Examples range from the casting of large metallic products to the cooling and reliability of small electronic components. Thermally induced stress is a major concern as it can lead to material damage and product failure. Material properties, thermal and mechanical, and process conditions such as the size and location of a feeder in metals casting, or the power dissipation in a computer chip, will govern the magnitude of these stresses. Temperature may also be influenced by fluid flow, for example, the airflow over a computer chip in a laptop will govern the rate of heat extraction, hence the temperature gradients in the chip and the evolving thermal stresses.This paper provides details on the governing equations for heat transfer (temperature) and solid mechanics (stress), their degree of coupling, and the numerical techniques used to solve them. Three examples are discussed to illustrate the use thermomechanical modelling. These also provide an insight into the degree of coupling required between the equations. The first example, involves thermal cycling of electronic components where a prescribed temperature field is applied. As temperature is known, this example only requires the solution of the stress equation. The second example also involves the modelling of an electronic component where the temperature field is also calculated. In both of these examples, the stress calculation is dependent on the temperature field, but the temperature calculation is not dependent of the solution of the stress equation (one-way coupling). The final example provides details on modelling the metals casting process. Both the temperature and stress equations are solved but, unlike the previous two examples, in this case the temperature field is dependent on the results from the stress calculation (two-way coupling)."

Jan 1, 2001

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By J. A. Russell

IT IS the purpose of this paper to show how the design of the larger slope hoists in use in the mines of the Dominion Steel and Coal Corporation has tended to evolve ta suit the particular conditions of operation. These hoists are all used for hauling coal in trains or trips of pit tubs up the mine slopes, which usually follow the dip of the seam . As the mine is developed to the dip and the slope grows in length, the length of the rope and the size of the hoist required to handle it rends to become extremely cumbersome. It has been found that the best economic conditions of hoisting are obtained when the length of the slope is limited to about seven or eight thousand feet. Beyond this length it is necessary to offset to one side of the line of slope and start a second or auxiliary slope, which will be served by its own hoist installed underground. With this hoisting distance as a basis, we find that we can economically hoist the outputs required, usually about 1,500 tans per eight hours per slope, by hoisting the coal in trips of about twenty boxes. This, on the grades obtaining, will require a rope of about l 1/4in. diameter, running at a speed of 1,200 ta 1,800 feet per minute, and requiring from 1,200 to 1,800 h.p. at the hoist shaft. The tendency is for the rope speeds of the surface hoists to be a little higher than the underground hoists which relay to them, so that the surface hoist has a small margin of time in hand. The oldest surface hoists were steam-driven, but, with few exceptions, these have given place to electric hoists. With the exception of one hoist, which was altered in design, the steam hoists have not had the opportunity of evolving in the same way as the electric hoists, and will not be mentioned any further.

Jan 1, 1944

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By Edmund S. Leaver, R. S. Dean, T. L. Joseph

The metallurgy of manganese has developed along the lines of iron metal¬ lurgy. Enough high-grade ore has Been available so that by reduction with carbon it could be turned into an iron-ma.nga.nese alloy and a slag containing some 9 to 15 percent manganese. More siliceous ores have been smelted in the blast furnace to form iron-silicon-manganese alloys called spiegel. When lower-grade ores came in for serious consideration, which lias only been since l°l4, two types of processes received the most consideration — hydrometallurgical processes to produce a concentrate which could be smelted like the higher-grade ore and processes involving concentration of the manga¬ nese from manganiferous iron ores by preferential reduction of the iron (184)1. Special chapters in this bulletin are devoted to the production of ferro¬ manganese from ore, the hydrometallurgy cf manganese, and the Bureau of Mines modification of the preferential reduction process. Other methods of producing manganese alloys from low-grade or refractory ores have been suggested and may find future application. Manganese has a very high affinity for sulphur and is particularly adaptable to concentration by matte smelting. According to Betts (26), manganese silicate may be smelted with pyrite to give manganese sulphide and iron silicate. This method would be applicable to concentration of either the silicate or carbonate ores. The sulphide, once obtained, could be roasted to oxide and reduced in the usual way. Another possibility for the production of manganese from silicate ores involves their reduction by silicon or manganese silicides. Swedish Patent 52290, February 25, 1925. covers the reduction of a slag rich in manganese by silicon-manganese alloy containing more than 10 percent silicon, Joseph H. Brennan (38.) describes the concentration of manganese iron ores by partial reduction with silicon. Beckett (7,4,19) describes the reduction of manganese dioxide with a manganese silicide for the production of standard ferromanganese. Beckett gives as a typical alloy, manganese 64.4, silicon 24.6, and as a typi¬ cal ore, 5S.5O manganese as MnO^. The product of the reaction between these two is 80.11 percent manganese and 1.22 percent silicon.

May 1, 1934

By R. O. Suzuki, S. Natsui, R. Nashimoto, T. Kumagai, T. Kikuchi, H. Takai

A newly developed computational fluid dynamics model based on a multi-phase particle simulation is presented for predicting the entrainment behavior of liquid metal into slag due to rising single bubble. By comparing results calculated using this model against experimental data, it was found that the transient behavior of bubbles and the two immiscible liquids can be accurately estimated by this method. The rupturing of the thin water film surrounding the bubble was less reliably predicted, but this 3-dimensional unsteady numerical model still nevertheless provides valuable new information for directly predicting the change in the liquid-liquid interface over time. This model predicted the Young-Laplace pressure, and the interface shape was simulated with volume conservation using this model as opposed to the conventional particle method. This simulation model can calculate both of dispersed phase and continuous phase seamlessly.

Jan 1, 2015

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By F. W. Horton

This paper covers the salient features of the occurrence and mining of sheet mica in the United States and the preparation of mica for market; presents the results of a study of the physical properties of domestic and foreign micas, which the author hopes may he of interest to every mica user, as it definitely answers many questions as to the suitability of various minas for particular purposes; and discusses mica-trade conditions and the future outlook for the domestic mica industry. ACKNOWLEDGMENTS The author takes pleasure in acknowledging his indebtedness to J. R. Thoenen, of the United Stator Bureau of Mines, under whose guidance the work reported herein was performed, and to Frank L. Hess, also of the Bureau, for information on the geological and mineralogical characteristics of mica-bearing pegmatites.

Jan 1, 1935

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By J. F. Poland

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By Shijie Wang

Lifetime achievements of Professor Reddy ’s teaching, research and scholarship in the field of chemical and materials science and engineering are briefly described. He has devoted his entire career in the introduction and application of process engineering principles to the quantitative description of materials processing reactions, and industrial operations. He has formulated quantitative methodologies based on first principles of thermodynamics, phase equilibria and kinetics to: design of slags and fluxes for production and purification of metals and alloys; development of Reddy-Blander model for a priori prediction of impurities capacities of melts; development of novel ionic liquid electrolytes for materials processing; development of new theories for alloys and molten salts; design materials for fuel cells and capacitors; use of thermodynamic approaches to predict physical properties of materials; industrial energy waste separation and remediation; and thermal energy storage. He is a scholar and mentor, and has made numerous scientific and service contributions to the society and metallurgical and materials engineering education.

Mar 1, 2017

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

By Lachezar Tsotsorkov

Being a mining company, Assarel-Medet has a significant impact upon the environmental components. In order to meet the legal requirements and the requirements stipulated by the effective permits as well as to reduce the environmental imprint throughout the years, the policy of the company to implement a number of projects to improve the environmental components quality and the environmental state in the company?s region. The projects associated with atmospheric air quality management and reduction of the impact exercised by Assarel-Medet JSC by implementing various measures to eliminate the potential sources of the impact, preventive and rehabilitation initiatives as well as organizational and administrative activities are among the most important ones. A stable improvement of atmospheric air quality in the region and minimization of the company impact upon the ground air state in the region was observed in the period from 2005 to 2012 due to the applied measures. This project is a contribution to the environmental protection, in particular to atmospheric air protection, by applying integral monitoring and modeling methods to identify the negative impact by the mining companies and plan measures to reduce and restrict it as well as to improve the quality of the environment and living area of people working and living in the impact range as an element of sustainable development.

Aug 1, 2013