Search Documents

By Robert A. Cortese, Carrie E. Lucci

Mine Safety and Health Administration (MSHA) regulations require underground coal mine operators to dust their mine corridors with an inert material to prevent coal dust explosions. The most commonly used material is pulverized limestone. Current practice to determine compliance with MSHA regulations requires the coal mine foreman or an MSHA inspector to collect samples of the deposited dust, a mixture of coal dust and limestone rock dust, for above ground laboratory analysis. To expedite this process, the U.S. Bureau of Mines has developed two instruments to facilitate the inspection and rock dusting processes, the explosibility meter and float dust deposition meter. The explosibility meter is a hand-held instrument which provides an in situ measurement of the explosible nature of homogeneous mine dust samples. The float dust deposition meter measures the mass loading density of the top layer of coal or limestone dust deposited on the mine floor during mining operations by the ventilation air. It may also be used to automate trickle rock dusting equipment. The operation of each device is based on the difference in the optical reflectance between the light limestone dust and the dark coal dust. The principal of the explosibility meter is based on the observation that, for a fixed coal volatility, the optical reflectance of dust mixtures is relatively constant at the limit of flammability, and independent of the coal dust particle size.

Jan 1, 1995

By Richard L. Ash

Introduction The blasting capabilities of commercial explosives are often rated according to their loading densities and detonation velocities. Both the density and velocity are relatively easily measured, the values of which can be used for determining the approximate detonation pressure developed by an explosive during any given set of blasting conditions (1-5). Knowledge of the actual rate of detonation attained at all points along a charger's length also is considered to give a good indication of how well the explosive is functioning. Many factors affect the density and velocity and have been thoroughly discussed by various authors (4, 6-12). For recording velocities several methods are available, but the resistance-wire, or probe, continuously recording technique has the distinct advantage of providing a record of the complete progress of an explosive reaction from the time it first initiates. Figure 1 is a copy of a typical record obtained by the procedure with certain significant information indicated. The theory and applications of the method are extensively covered in the literature so need not be reviewed for this report (13-18). Only the specific equipment and procedure employed for this investigation are presented.

Jan 1, 1973

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By Mingchun Lu, Zhijia Liu, Xueqi Zhang, Jianliang Zhang

"In order to solve the problem of shortage of scrap, especially high quality scrap, a new substitute for scrap or DRI has been developed. The decarbonization mechanism of granular pig iron has been analyzed and the technical process and decarbonized granular pig iron have been evaluated in this paper. The research result shows that this new process is superior to direct reduction process in product quality, construction investment, operation flexibility, production efficiency etc. Decarbonized granular pig iron (DGPI) not only can be used as conventional scrap but also can be charged into EAF as high purity .burden equivalent to heavy scrap:IntroductionIn the past years, with the universal application of continuos casting technique in China, the amount of scrap generated inside steelworks has been reducing continually. On the other hand, the EAF steel proportion is increasing and this gives to the obvious change in structure of steel product. At present, the requirement on both scrap quantity and scrap quality is being paid more and more attention. Because China is a country which is devoid of scrap and poor in resource (nature gas and high grade iron ore) for developing direct reduction iron (DRI) so that sponge iron can not be produced cosmically in China and has to be mainly imported. Instead of part of scrap, some cold pig iron in cold state has been charged into EAF in China. However the high carbon content in pig iron has limited its proportion in EAF metal burden. Because the price of pig iron is lower than that of imported DRI in China, the technique of granular pig iron decarboniztion is hopeful to become effective way to produce substitute for scrap or DRI."

Jan 1, 2000

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By Kristen Dunlap

There are several thousand remote stream crossing structures in the Tongass National Forest in need of removal. In 2007 thirty-three collapsing log bridges, log culverts, and metal culverts no longer in use were removed with explosives. Species of salmon, trout, char, and sculpin are present in the project area. Blasting overpressures may injure or kill fish in streams and ground vibrations can damage salmonid embryos in streambeds. Regulatory agencies offer guidelines with limits for blasting induced overpressures and vibrations. However, there has been no quantification of blast overpressures in shallow streams. Methods used to predict lethal levels for various blasting applications have not been completely validated. This research provides guidance for analyzing ground vibrations and water overpressures during blasting activities in or around fish streams.

Jan 1, 2009

By D. D. Rodier

Most zinc concentrates contain some silver and varying amounts of such valuable trace elements as gold, indium, germanium and gallium. With increasing similarities in plant installations, the predominance of electrolyte process and the increasing environmental constraints on iron disposal, it is essential that zinc smelters optimize the recovery of any valuable elements in their feed stocks. The process options, to date, of smelting, flotation or leaching of silver-rich leach residues cannot be applied economically to all installations. It is therefore necessary that new innovative processes, to recover silver and other valuable metals from relatively low grade feeds, be developed. This paper attempts to place this strategy in the context of today's constraints and will also provide a simple evaluation tool for any process alternatives.

Jan 1, 1990

By Ben-Zion Weiss, Melvin R. Meyerson

Chromium diffusion coatings on commercial Armco iron lead to carbide precipitation at the grain boundaries in and below the coatings. High compressive stresses are introduced into the coating and, as a result, tensile stresses are introduced into the base material below the coating. In coated samples, fatigue cracks form at the grain boundaries below the coating after only a limited portion of the total lifetime (5 to 10 pct). Residual tensile stresses and a stress concentration caused by precipitated carbides seems to be responsible for early crack nucleation. Stage I of Propagation may be divided into two substages: I-a in which the crack Propagates along grain boundaries, and I-b in which the crack propagates along slip boundaries according to a shear mode. In uncoated samples, the cracks form at slip bands after 40 to 50 pct of the total lifetime. In coated samples the Propagation process takes longer than in uncoated samples because of the moderate rate of crack extension until the crack breaks through the coating. The chromium-diffusion coating causes little if any increase in fatigue life. CHROMIUM diffusion is one of the most popular processes used to apply coatings to iron alloys. This popularity stems from the fact that the diffusion treatment is comparatively easy to carry out, and it improves certain surface properties such as corrosion and wear resistance as well as some other properties. Very little effort has been devoted to the investigation of the effect of chromium-diffusion coatings on mechanical properties and particularly on fatigue properties. Since the chromium coating usually represents a small fraction of the total volume of the base material it is generally assumed that the macro properties are dependent principally on the base material rather than the coating. Insofar as fatigue is concerned, there are indications that the fatigue life of the chromium coating is not less than that of the basic material and the fatigue properties are generally not reduced by it.' But chromium diffusion causes drastic structural and chemical changes in the region of the material surface2-4 which introduce additional residual stresses. Such changes must affect fatigue crack nucleation and may sometimes affect the initial stages of propagation. Furthermore, it is conceivable that the secondary stages of the crack propagation could be influenced by some irreversible structural changes in the core of the material, which stem from the long-time heat treatment at high temperatures required to apply the coating. This paper analyses the structural and compositional changes produced in commercial Armco iron by a chromium-diffusion coating and the effect of the coating on fatigue crack initiation and propagation. EXPERIMENTAL PROCEDURES The investigations were carried out with commercial Armco iron. The chemical composition of the iron, the number of specimens tested, the grain size produced during chromizing and heat treating, and the thickness and microhardness of the chromized layers are shown in Table I. Samples were chromized by a gas diffusion process. The temperature and time of the diffusion coating process were chosen according to a previous grain growth study. It had been found that at a temperature of 970°C and a holding time of between 3 and 9 hr there are practically no changes in grain size. To describe the grain size more accurately the ASTM method5 was supplemented by a statistical analysis of the mean volume diameter as outlined by Fullman6 and The The mean volume diameter was deter- mined from D = p/2m where D is the mean volume diameter, and m is the mean reciprocal value of grain diameters as seen on the micrograph. The shape and the size of the asymmetrical sample, see Fig. 1, were chosen so as to facilitate the study of fatigue crack initiation. Before coating, the samples were machined and the surface of the groove was polished. After chromizing, the two side surfaces were machined and polished so as to retain the coating only on the top surface of the groove. Residual stress in the chromized layer was measured on the top of the grooved section of the specimen after the diffusion process. The inclined incident X-ray beam procedure was used.9'10 The computations were performed with the initial assumption of a zero surface normal stress component. An electron microprobe analyzer was used to obtain the relative amounts of chromium and iron con-

Jan 1, 1970

By Zhucheng Huang, Zhikai Liang, Ronghai ZHONG, Lingyun Yi

In this work, research of reduction process was studied by means of rotary kiln (u1.5 m /C215 m) process anatomy in order to provide fine guidance to large-scale operation. It was shown that the average reduction degree of 89.96% and metallization ratio of 85.15% were obtained at the highest temperature of 977°C and total residence time of 90 min. The generation amount of metallic iron in section of temperature higher than 900°C and lower than 900°C was 34.15 and 56.38%, respectively. The section of lower temperature of 830–900 °C played an important role in formation of metallic iron, making it possible for mini-pellet to reduce quickly at lower temperature. Two main tasks were completed for mini-pellets in rotary kiln: the reduction of iron oxides in the range of 15.0–4.5 m as well as migration and bene ficiation of metallic iron, facilitating the subsequent separation of iron and gangue minerals.

Mar 1, 2018

By James Stuart

A man died when the primed charge he was holding against his chest exploded. He was doing legitimate explosive work, and he was following all the safety procedures he had been taught. He and his colleagues had done this, thousands of times previously, with no ill effects.

Jan 1, 2007

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

By C. R. Copeland

Combustion processes, comminution and materials handling can generate airborne particulates. Regulation of these particulates by the U.S. Environmental Protection Agency (U.S. EPA) is becoming progressively more stringent, and regulations will soon include ?nanoparticulates,? which are particles finer than 100 nanometers (0.1 mm). Nanoparticulates are believed to have significant negative health effects due to their high surface area and reactivity. Although it was argued that nanoparticulate concerns were only important for combustion, studies at Michigan Technological University have shown that materials handling and comminution release significant quantities of nanoparticles into the air. Laboratory studies have shown that the use of sodium metasilicate reduced airborne particles finer than 10 mm (PM10) by 86% and particles finer than 2.5 mm (PM2.5) by 80% for iron ore. Additional studies were conducted that revealed that nanoparticulate emissions were present in the types of operations conducted at pyrometallurgical facilities.

Jan 1, 2008

By Shenghui Guo, Ying Lei, Hao Niu, Huilong Luo, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the combination of microwave drying (MWD) and heat pump drying (HPD) drying experiments were designed by response surface methodology (RSM) based on central composite design (CCD) using design expert software (Version 7.15), and the process parameters were optimized. The conditions given by software are: the MWD time is 4.6 or 4.4 min; the HPD time is 9.0 or 8.6 min; and the sample mass is 620 or 600 g. Under those conditions the moisture content is 1.0 10-2kg water/kg wet basis, and the effectiveness ratio is 0.70 kg water/kwh. The results of confirmatory experiments conducted under the optimized conditions show the combined drying have superiority of decrease of energy consumption and increase of handling capacity over the single MWD or HPD.1 IntroductionSilica sand is one of a silicate mineral with properties as hard, anti-friction and less reactive, commonly used as raw material for foundry and construction. The silica sand obtained from mineral dressing processes such as scrubbing, magnetic separation and flotation. Its moisture content is approximately 0.08~0.12 kg water/kg wet basis. The most common methods used for drying are solar drying and hot air drying. But these methods have some shortcomings: for example, the solar drying has longer process time due to low energy yield, [1] hot air drying has low-energy efficiency and a lengthy drying time. [2]Microwave is electromagnetic waves with frequency are 300MHz to 300GHz. The outstanding features of microwave heating are rapidity and selectivity. The water specific inductive capacity of 60~78 is much bigger than common materials, the moisture always quickly absorb electromagnetic wave and rapidly transfer to vapors. So, it can significant reduce the drying time. [3] Heat pumps (HPs) are devices for raising the temperature of low grade heat energy to a more useful level using a relatively small amount of high grade energy."

Jan 1, 2011

By G. M. Ellis

This paper deals with some aspects of concrete construction in remote locations and/or cold climates. The writer's experience covers 25 years in construction in western and Central Canada. I will bring forth some pertinent observations and cost facts learned from this experience. Let us start by saying that there is nothing more important than preplanning the entire project. By this I mean the production of the engineering design, working drawings, soliciting of prices and ordering of all equipment and contractors work, the delivery of all equipment and all onsite work. All of this should be placed on a master schedule, preferably a C.P.M. We have been using C.P M. Scheduling for all of our work for 5 years and have found it in-valuable. This preliminary schedule will show initial items of work and target dates. After main equipment orders are placed and deliveries confirmed, the construction schedule can be revised to include manpower and construction equipment requirements. From this information the size of camp is determined. This, of course, must be ordered several months ahead. The manpower schedule can be broken into trades to tell us the number of men of each trade required at any time. This is important in helping to determine where the men must come from and whether or not any incentive is needed to get them. The schedule will also point out if it is impossible to get the project closed in before winter becomes too severe unless overtime is worked or the project is started in early spring. In most parts of Canada cold weather starts in October and lasts through April. A common term of reference has been to wait for the frost to come out of the ground before starting work in the spring. In some areas this can be as late as June. The construct-

Jan 1, 1971

By R. L. Montgomery

Heats of solution of cerium metal and cerium (III) chloride in hydrochloric acid were measured. The standard heat of formation of the aqueous cerium (III) ion at 25° C is -166.1 ± 0.3 kcal/mole. Heats of solution of cerium (III) chloride in hydrochloric acid are consistent with the existence of a complex CeC1++ having a stability constant of 1 and a heat of complexing of 5.4 kcal/mole.

Jan 1, 1962

By Rami Abousleiman, Gabriel Walton, Sankhaneel Sinha

"Although conventional coal mine designs are conservative regarding pillar strength, local failures such as roof-falls and pillar bursts still affect mine safety and operations. Previous studies have identified that discontinuous, layered roof materials have some self-supporting capacity. This research is a preliminary step towards understanding these mechanics in coal-measure rocks. Although others have considered broad conceptual models and simplified analogs for mine roof behavior, this study presents a unique numerical model that more completely represents in-situ roof conditions. The discrete element method (DEM) is utilized to conduct a parametric analysis considering a range of in-situ stress ratios, material properties, and joint networks to determine the parameters controlling the stability of single-entries modeled in two-dimensions. Model results are compared to empirical observations of roof-support effectiveness (ARBS) in the context of the coal mine roof rating (CMRR) system. Results such as immediate roof displacement, overall stability, and statistical relationships between model parameters and outcomes are presented herein. Potential practical applications of this line of research include: (1) roof-support optimization for a range of coal-measure rocks, (2) establishment of a relationship between roof stability and pillar stress, and (3) determination of which parameters are most critical to roof stability and therefore require concentrated evaluation.INTRODUCTIONRecent studies on pillar design have suggested that the assumptions utilized in traditional methods such as tributary area theory (TAT) (i.e. overburden has no self-supporting capacity, infinite pillar array, and CHILE material properties) are invalid in many geo-mining conditions (Esterhuizen, Mark, and Murphy, 2010; Frith and Reed, 2017). Although TAT is conservative with respect to pillar loading, and mine fatalities have steadily decreased since 1990, roof-falls and pillar bursts still occur and injure hundreds of miners per year (Mark, Pappas, and Barczak, 2011). Even though large-scale global mine failure has not occurred in a US coal mine since 2007, the mechanics of global and local stability as governed by the relationship between geologic parameters, mine geometry, and engineering design are still not well-constrained.Numerical methods are a highly effective tool that can be used to gain further insight into these relationships. When using such an approach, calibration to existing empirical relationships is imperative to ensure that numerical model results are realistic. In this study, we utilize the discrete element method (DEM) approach in Itasca’s Universal Distinct Element Code (UDEC v. 6.0) (Itasca, 2010).DEM accounts for explicit separation and contact of individual deformable blocks (Jing, 2003) and captures how discontinuities can affect system behavior. Discontinuous and anisotropic rockmass properties are typical features in coal-measure rock which contain various horizontal (bedding) and sub-vertical (joints) fractures depending on their depositional environment, diagenesis, and historic and current stress states."

Jan 1, 2019

By Jorge MRS Relvas

Recent research both on active and fossil systems has demonstrated that shallow subseafloor replacement processes are not only viable depositional mechanisms for massive sulfide mineralization, but likely contributed as a major component of the mineralization occurring in large VHMS deposits and in many present-day seafloor hydrothermal systems. In the giant Neves Corvo deposit, as in many others VHMS deposits of the Iberian Pyrite Belt, there is overwhelming evidence for silicate-sulfide replacement processes being largely responsible for the efficiency of the ore-forming systems and huge size of the deposits. Textural evidences at all scales, coupled with a well-constrained mass-balance geochemical analysis, indicate that extensive replacement in the lavadominated volcanic rocks of the footwall sequence, and disseminated replacement mineralization in the volcaniclastic and/or sedimentary units were major mechanisms of ore formation in the Neves Corvo deposit. Shallow metal deposition prior to fluid discharge on the seafloor is likely to play a major role in seafloor massive sulfide mineralization. This premise should be envisaged as critical in evaluating the economic potential of seafloor resources, and should certainly be part of the equation when plans for seafloor mineral exploration missions are drawn.

Sep 14, 2011

By L. E. Mylting

Modern ash handling systems exist in considerable numbers and a great deal of design and operating experience has been accumulated, It is the endeavor of this paper to point to a number of frequently recurring problems, A general appreciation of these problems will be helpful in both design and operation of systems. The light fly ash and the heavy bottom ash present different problems, and each will therefore be treated separately. Fly ash is collected in the ducting from the furnace to the stack and beneath the mechanical and electrostatic dust collectors. The greatest amount of dust is collected beneath the mechanicals and electrostatics. Hoppers are generally provided as integral parts of the collector. Suitable valves and piping are connected to these hoppers for removal of the dust. The size and shape of these hoppers are important factors in determining frequency of handling and the capacity of the system.

Jan 1, 1958