Search Documents

By Anne Lemnitzer

Experimental data are the cornerstone of scientific research, providing empirical evidence to validate hypotheses, test theories, inform decision-making and help develop innovative design and analysis methods. However, beyond traditional empirical validations, experimental data have also become the most crucial component of AI algorithms, measuring the algorithms' effectiveness, and allowing engineers to ensure their reliability and applicability. The DFI "Rock Socket Project," awarded in the spring of 2018 allowed for the indispensable, experimental data-based validation of structural shear magnitudes, which have been hypothesized and discussed for years within the deep foundations community and cautiously approached by many design engineers. The fundamental project idea, i.e., the investi- gation of pile shear magnitudes through experimental research, was sparked during a heated discussion in the October 2016 Drilled Shaft Committee meeting in New York. Should we design for amplified shear at the rock socket of a drilled shaft or is this merely an artifact of the p-y design approach? Data were needed to provide consensus.

Nov 1, 2023

By Jewel Andrew Gomes

Arsenic is considered as one of the toxic materials being controlled by Environmental Protection Agencies in several developed and developing countries. It is found in the nature as constituents of the soil, minerals and also in various organic forms. It enters the air, water, and land from wind-blown dust and gets into water from runoff, leaching, soil erosion and anthropogenically from chemicals used for wood preservation, insecticides, medicine, military purpose, pigments, and electronic circuitries. There are several techniques available for removal of Arsenic, such as coagulation/filtration, lime softening, ion exchange, reverse osmosis, nanofiltration, wet chemical, and electrochemical. Electrocoagulation has been found as one of the most efficient techniques to remove inorganic arsenic with more than 99% efficiency. In this paper, we present our work on electrochemical treatment of both the inorganic and organic arsenic from water using various sacrificial electrode materials, i.e., iron, aluminum, copper, and combination of them. The floc produced by this method has been also characterized using XRD, SEM/EDS, FTIR, and cyclic voltammetry.

Jan 1, 2010

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

By Minna Rämä

Iron containing leach residues like jarosite and goethite from electrolytic zinc production contain many valuable metals and harmful substances. These metals and substances should be removed in order to obtain an acceptable, stable and reusable product, and maximize economic feasibility as well as minimize environmental footprint. In this work, the processing of jarosite leach residue was studied in laboratory scale experiments under oxidizing and reducing conditions at high temperatures. First, the pretreated material was melted and oxidized to produce a melt of metal oxides. Second, the oxide melt was reduced in CO–CO2 atmosphere. Target after the reduction step was to obtain a clean slag and a liquid metal or speiss phase that collects the valuable metals, such as silver. The kinetics of the thermal processing were studied for determining optimal times and conditions for the aforementioned process steps. The preliminary results show that the process is thermodynamically feasible, and the desired phases can be obtained in the experimental conditions investigated.

By P T. Stoker, A Allman, D P. Carville

Classification of mineral resource estimates is one of the most important responsibilities of the Competent Person. In recent years, classification decisions have been driven more by the detailed block-by-block attributes generated by the now widely applied geostatistical estimation methods, and less by a general geological overview. This is increasingly resulting in æspotted dogÆ outputs, in which blocks of Inferred Resources or unclassified material separate blocks of Measured and/or Indicated Resources, or individual drill holes are surrounded by annuli of Measured and Indicated Resource blocks. Not only are such outputs potentially misleading, since they ignore fundamentals such as continuity of geology and mineralisation between drill holes and the imprecise nature of resource estimation, they can also cause substantial problems for engineers undertaking mine designs and estimating ore reserves, particularly for underground mines. Competent Persons for mineral resources must keep in mind the purpose of their work, and should use their experience and judgement to avoid or smooth out æspotted dogÆ classifications, providing a result commensurate with the level of geological and resource estimation confidence. For their part, ore reserve Competent Persons must understand the resource estimation and classification process, and should question resource classifications that are not consistent with the level of geological and resource estimation confidence.

Jan 1, 2006

By Boris CARO VARGAS, Bernard Theron

"In early 2014, Nicholson Construction Company was awarded, together with its tunneling sister company Bessac, the Norris Cut Miami Tunnel Project. The 2.5-meters diameter segmental lined tunnel, 1600-meters long, is aimed to replace the existing 54” force main connecting the Waste Water Treatment Plant (WTP) on Virginia Key to Fisher Island. To overcome project challenges such as the highly permeable limestone of the Fort Thomson Karstic Formation (one of the most permeable formation in the World), the project team has developed State of the Art solutions: The TBM was launched with pipe-jacking technique for the first 70-meters and then converted to segment erection mode. It allows substantial schedule savings and drastically reduces the size of the circular launching shaft. The TBM, jointly designed and manufactured by Bessac and Herrenknecht, can convert from slurry to EPB mode within a few minutes. The cutters can be replaced by wet divers thanks to an innovative application in the TBM industry. PRESENTATION OF THE PROJECT The aim of this project is to replace the existing 54-inch force main pipeline which transmitted all sewage collected from Miami Beach, Surfside, Bal Harbour, Bay Harbor, North Bay Village and Fisher Island to the Central District Wastewater Treatment Plant (CDWWTP) to Fisher Island. The existing pipeline consisted of pre-stressed concrete cylinder pipe which is in poor condition in a number of locations and could be subject to sudden failure. An adjacent portion of this existing force main under the Government Cut (North Fisher Island) has already been replaced as part of a previous design-build contract and involved the installation of a 60-inch diameter fiberglass-reinforced mortar pipe installed inside a micro-tunneled casing."

Jan 1, 2016

By Azadeh Riahi

The main goal of this paper is to investigate the effects of permeability anisotropy in Large Open Pit (LOP) mines for problems that exhibit homogeneous anisotropic characteristics. The most important effect of the groundwater flow in open pit mines is on the stability of the pit slopes. This study will investigate the effects of having increased permeability in both horizontal and vertical directions on three aspects of LOP behavior, location of phreatic surface, pore pressure distribution and stability of slopes. The hydromechanical coupling is simulated using a one-way coupling approach. The Shear Strength Reduction method (SSR) is applied to assess the stability of slopes. The studies performed in this paper suggest that anisotropy in permeability leads to a significantly different regime of pore pressure dissipation depending on two aspects, ratio of anisotropy and the relative magnitude of permeability to simulated time. As a result, variation in safety factors and the location and depth of the failure surface must be expected.

Jun 1, 2012

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By P. Eger

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By Fujio Ishii

The deoxidation of liquid nickel and nickel binary alloys with silicon has been determined at temperatures between 1500°C and 1650°C using quartz crucibles in order to investigate the deoxidation of nickel based alloys. The equilibrium constant of the deoxidation reaction in liquid nickel and the effects of the different alloying elements such as chromium, molybdenum, tungsten, iron, cobalt and coppcr on the activity coefficient of oxygen in liquid nickel have been established.

Jan 1, 1993

By D. Limpitlaw

The origins of mine closure practice have influenced the way in which it is implemented by companies and regulators. Mine closure practices essentially started developing in the 1970s in countries with advanced economies and mature mining industries. In these settings, the emphasis was justifiably placed on restoration of the landscape and an attempt was made to return to the ?natural? pre-mining land cover. These practices continued to evolve and incorporated socio-economic and cultural aspects, especially after the Brundtland Report in 1987 and the subsequent Earth Summit in 1992. Today mining is increasingly occurring in remote parts of developing countries where there may be significant need for infrastructure such as roads, clinics, and schools. The costs of returning land to low (economic) value pre-mining use may be far greater than establishing a viable postmining land use that could potentially add value to the community and take pressure off sites for greenfield development elsewhere. Furthermore, natural resource limitations (such as topsoil availability) may limit the degree to which the historical land cover can be re-established. Establishing post-mining land uses may aid in mitigating the loss of employment that is inevitable when mines close. Stakeholder participation in establishing post-mining land cover and land use options is critical for long-term success. Similarly, third parties must be identified to support the development of the post-mining land use This paper draws on the experience of the authors in several developing countries and presents a case for maximizing re-use of mining infrastructure. The paper does not advocate the adoption of poor rehabilitation standards, nor or the wholesale destruction of land capability, but rather leaving key infrastructure in place for post-mining use that may support sustainable development.

Jan 1, 2014

By H Arvidson, B Spence, S Helm

Mining is the art of disturbing ground. All phases of a mine’s life cycle from exploration to building and operating a mine, through closure, has a physical impact on the earth. There is currently increasing public and stakeholder awareness owing to a wide range of issues including heritage protection, environmental stewardship, and social impacts therefore ground disturbance must be conducted in a way that honours and respects all agreements, regulations, legislation, and social expectations. A comprehensive ground disturbance permitting process has been developed through consultation with major mining companies and Traditional Owner groups. It operates from strategic business planning through to closure and rehabilitation. Adherence to the principles and process of permitting helps to minimise risk by ensuring that mining companies conduct their business in an inclusive, professional, reliable, and consistent manner that stakeholders reasonably expect, and that mining companies can be proud of. Built on a geographical information system, supplemented with a specialist database, this process allows request, review, and approval by subject matter experts, to operate in a common environment that is transparent, facilitates collaboration, improves efficiencies, and reduces the risk of error or omission. The application of new technology can effectively highlight changes that naturally occur in today’s dynamic ESG domain and provides the perfect platform to record actual disturbance against authorised and planned allowances. The social license to operate demands that strong governance of the ground disturbance process, described herein, can be demonstrated to any interested stakeholder, and mining companies recognise that this principle is central to the betterment of the mining industry.

Sep 18, 2023

James Barnes is Managing Director of James Barnes & Associated Ltd which is a company that has invested ten years of development to provide developers with a transparent, user friendly consultation framework that identifies who needs to be consulted, how they are to be consulted and procedures required to manage the risks associated with getting all the wrong! Despite the assertion above, this paper is not about to provide delegates with the answer to whom they ought to consult or identify the expectations that Maori might have in regard to the consultation process. It would be a very brave person indeed who would venture an opinion on such a sensitive subject. There are no short cuts to finding out what expectations Maori might have on any given situation. Nothing can be taken for granted. What this paper will attempt to do however is provide practical insights into what might be on the minds of Maori interests as they deal with the issues associated with mineral resources, particularly those under Treaty of Waitangi Claim. The Treaty of Waitangi has a significant bearing on the current debate between Maori and the Crown regarding ownership of mineral resources in New Zealand. The Waitangi Tribunal is currently hearing a case presented by a number of Iwi over the ownership of oil and gas resources in Taranaki and Hawkes Bay. Others will follow. The Crown and Maori have never been able to settle differences over ownership rights without resorting to legal action and it looks like this scenario is about to be repeated in regards to minerals. The Crown has a duty to actively protect the Maori interest. This is a fundamental expectation in the relationship between Maori and the Crown. In the case of minerals, Maori have yet to see the Crown do its duty. The impact on developers has become evident through Maori objections to consent applications as the issues of mineral right remain unresolved.

Jan 1, 2000

By A. T. Churchman

The deformation modes of rhenium have been identified as those typical of the hexagonal metals, titanium, zirconium, and beryllium whose c/a ratios, in common with rhenium, are less than ideal for close packing. Slip is observed on (1010), (1011), and (0001) planes and twinning on (1121), (1122), and (1012) planes. The very high rate of work hardening is believed to be associated with intersecting partial dislocations on two (1010) systems which can combine to form sessile barriers. If the stacking fault energy is low, as postulated by Seeger, these barriers should be strong and not easily bypassed by cross slipping. Such an explanation could also account for the very small temperature dependence of the yield stress which was observed. RHENIUM is interesting scientifically as a member of the group of high melting point hexagonal metals: titanium, beryllium, and zirconium with a c/a ratio less than that for ideal close packing. Unlike them, however, it work hardens at a very high rate. This rate is greater and continues to a much higher degree of deformation than for nickel, normally considered to have a high rate of work hardening. This paper presents experimental observations on the modes of deformation of rhenium and, by comparison with other hexagonal metals, some speculation on the cause of the high work hardening. MATERIALS Johnson, Matthey rhenium powder of both 99.9 pct and 99.5 pct purity, see Table I, was compacted at 10 tons per sq in., part sintered at 1350°C in vacuo, and finally arc melted in a "gettered" argon atmosphere arc furnace to produce small buttons. Little difference was observed in the as-cast hardness or working down behavior of the two purities suggesting that either silicon and potassium do not have a significant effect on the working properties of rhenium or they were lost during arc melting. SPECIMEN PREPARATION The cast structure was broken up by cold-rolling with inter-stage annealing at 1600o or 1800°C in a vacuum high-frequency furnace using a tungsten susceptor. Strip for tensile testing was taken from two thicknesses of material 0.011 and 0.064 in. The former with intermediate anneals at 1800°C had a grain size of 900 grains per sq mm, while the latter with inter-stage annealing at 1600°C had a grain size of 3600 grains per sq mm. A coarse grain size was obtained by secondary recrystallization in a half button cold-worked by 30 pct reduction. Annealing times of from half an hour to several hours at 2200° to 2600°C in a "gettered" argon atmosphere arc furnace1 resulted in grains of up to 2 mm diam.

Jan 1, 1961

This paper provides a summary on the use of the POL YCOM high pressure grinding roll (HPGR) for increasing extraction in copper leaching. The energy-efficiency and significant hydrometa1lurgical benefits of the HPGR result in better acid-curing, higher solution application rates, improved copper extraction from various copper minerals and better recovery from high acid consuming ores. The HPGR's metallurgical features such as micro-fracturing, better liberation of disseminated and veinlet copper, increased oxygen and lixiviant penetration lead to higher copper extractions than achieved by conventional crushing. Flowsheet options, operational characteristics and applications for various copper ores are outlined.

Jan 1, 1996

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By F. L. Pirkle

The mineral zircon is mined for use as specialty foundry sands, abrasives, ores of ZrO2 and zirconium metal, refractories, and zirconium chemicals. It is produced as one of several products from heavy-mineral sand deposits associated with fossil shorelines. Because of its low coefficient of thermal expansion, its high melting point, its high refractive index, and its chemical inertness, it is an attractive refractory material. Zircon varies from deposit to deposit in terms of grain size, grain shape, and chemical impurity. Thus, there is a wide range of commercial products differing in impurity levels, particle shapes, and grain sizes.

Jan 1, 1992

By Scott Turner

Many of you radio listeners have probably never seen a mine . You may be glad of it, but you should not forget that there is a vast army of men in this country who not only have to see mines , but have to work in them day by day in order that you may be supplied with many of the things you need. Specifically , nearly a million men work in the mines of the United States , 700,000 in the coal mines , 110,000 in the metal mines , 100,000 in other mines and quarries , and 75,000 in the oil and gas fields . On a stormy night , the average citizen is apt to think of the perils of the seaman . Particularly in the old days before steamships , many a prayer went up " God help the poor sailor on a night like this . " At the same time , the sailormen often expressed fear for the poor landlubber , exposed as he was to the danger of falling chimneys , swaying signboards , and uprooted trees . So with the miner . Many of you may pity him , for working underground in complete darkness except for feeble artificial lighting , mining coal or ore , drilling hard rock , handling explosives , and perhaps breathing vitiated air . On the other hand , on stormy days , with rain , snow or hail falling , and with the temperature low , or on hot bright days , I have often heard miners joke about the poor fellows who had to stay " on top, " and could not get " down below" where there was no wind , where no snow fell, where the temperature was unchanging , and where a man could have his own working place , arranged to suit himself , with little interference from meddlers and with no automobiles to dodge . So do not feel too sorry for the miner . He is quite apt to be a strong , healthy , hearty person , making pretty good wages , and fairly well contented with his lot .

Dec 1, 1930

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By S. C. Termes

To help develop the basis for new fine-particle separation methods, the Bureau of Mines has investigated the use of cross-linked starches containing four chelating groups--carboxylate, iminodiacetate, dietha-nolamine, and xanthate--as flocculants for selected metal oxide and hydroxide mineral fines. It was found that those starches capable of interacting with the mineral surface by a chemisorpti,on mechanism (as indicated by zeta potential measurements) produced the highest recover-ies and'grades of the metal oxide or hydroxide when flocculated from a binary mixture with quartz. The effects of pH, dispersing agent, stirring rate, stirring time, and starch dosage on selective flocculation were studied for binary mixtures of hematite and chromite with quartz. Floc strength becomes important in achieving maximum recoveries by mechanical postflocculation separations.

Jan 1, 1985