Search Documents

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

By J. R. Walls

Mining is one of world's oldest industries. Its rich history continues into modern times. The Waste Isolation Pilot Plant (WIPP) located in southeastern New Mexico is writing the next chapter in mining history. In fact, WIPP technology is the key to closure of the nuclear cycle with the disposal of nuclear waste in a deep geological repository. It might seem odd that the age-old institution of mining would be linked to the problem of nuclear waste disposal. In fact, the nuclear industry would not exist without mining. Uranium ore is mined from either underground or surface mines as the initial step in harnessing the magnificent resource of nuclear energy.

Jan 1, 1996

By W. E. Anable

The Bureau of Mines studied the purification of commercially available vanadium in the 100-kw electron-beam furnace. Purification studies were conducted on a 100-gram button scale by melting and holding the liquid vanadium at temperatures ranging from 2,060° to 2,080° C at pressure of 5(10)-5 torr for periods ranging from 5 to 20 minutes. The effect of doping vanadium with carbon and metallic additions was determined. This study demonstrated that hydrogen was readily removed to 3 ppm or less, oxygen and carbon were reduced to less than 100 ppm each, and the metallic impurities were reduced Co the range of 10 to 500 ppm. The nitrogen content was not reduced in any of the buttons; rather, the nitrogen concentration generally increased as samples were held for successively longer periods. Oxygen was removed much faster and more completely when vanadium was doped with small carbon additions or one of several dopes prior to melting.

Jan 1, 1967

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By Shankar S. Hegde

In many areas of the United States much of the most readily minable coal is nearing depletion, while at the same time, increased national attention is being given to coal as a major alternate energy source. If some of the thinner, more erratic, deeper and lower quality coals, which comprise the great bulk of U.S. resources, are to be mined efficiently and economically, greater attention must be devoted to careful planning of mines and to preparation facilities. One of the cornerstones to careful and successful mine planning is precise knowledge of coal thickness and areal distribution, roof and floor quality, and seam quality. Data on which this knowledge is based are obtained from various borehole techniques and, in some cases, seismic methods. Despite the many technical innovations that have been made in acquiring subsurface data, little attention has been given to the problem of systematic storage and retrieval procedures of the data and assembling them in a form that can be used for various computer mapping programs now available. (See Bilter and Martin, 1977; Bryant and Zobrist, 1977 and Farrell and Wherry, 1978). The purpose of this paper is to describe a series of user oriented programs developed over the past five years which are specifically designed for precise logging of rock core, accurate storage and retrieval of this data, correlation of seams between logs, tagging seams, computer assisted data posting of maps and preparing maps and profile sections for report illustrations. The entire system stresses increased precision and speed for a series of operations which are now largely manual, time consuming and prone to error.

Jan 1, 1980

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By T. Thriveni, Ji Whan Ahn

"The current advanced technologies for the manufacture of light weight metals processing significantly increasing and attributes to the safety, performance, recyclability and economy. Still lack of technologies developed for light weight metals processing waste utilization and application. Environmentally friendly methods need to develop for better understanding the processing waste utilization. Alumina and aluminium processing creates a wide range of waste products, the most significant being is red mud. Bauxite residue is a high volume hazardous waste and nearly 3 billion tons have been dumped worldwide. Approximately, 120 Million tons/yr of red mud being produced without any environmental sustainable solution. Currently the most significant technology is waste utilization. The bauxite residue is suitable for road base construction, golf bunker sand, back fill and, general fill. Sustainable recycling technologies are necessary for the bauxite residue utilization for the recovery of rare earth elements and cement materials. Carbonation or CO2 sequestration of carbon dioxide is a method pioneered for the bauxite residue is modified to reduce alkalinity. The carbonation of alkaline material is an inexpensive and safe process that leads to the formation of thermodynamically stable products. The use of the carbonation can be an advantageous solution for environmental climate change and sustainability problems in the new century.INTRODUCTIONIn 2014, bauxite consumption was estimated to be 9.6 million tons, nearly all of which was imported, worth an estimated 269 million dollars. More than 95% of the bauxite was converted to alumina, and the remaining 5% went to non-metallurgical products, such as abrasives, chemicals, proppants, and refractories. Global aluminum demand is growing steadily spurred by growth in India and China (RBCAluminum Market Outlook, 2013) (Figure 1). Aluminum consumption is expected to rise 5% annually through the end of the decade, reaching 67 million tons per year by 2020. Global bauxite production decreased by 17% from that of 2013, principally owing to lower production in Indonesia. In response to a Government ban on exporting bauxite and other unprocessed mineral ores that took effect on January 12, 2014, bauxite mines throughout Indonesia shut down and production decreased from 55.7 million tons in 2013 to an estimated 500,000 tons in 2014. The ban was part of a mining law that was instituted in 2009 to increase development of downstream processing facilities in Indonesia."

Jan 1, 2016

By P. Sklenicka

Remediation of the environmental (and social) disturbances caused by opencast brown coal mining in the past in north-west Bohemia isa priority for state environmental policy. In order to provide a concept for full restoration of land following disturbance by opencast mining, a special interdisciplinary project supported by a grant from the Czech Ministry of Environment was started in 2000. The initial stage of the project was intended to summarize and evaluate the findings and the works carried out in connection with various reclamation activities in the afflicted area over a period of more than 50 years. The main aims of the three-year project are to make use of the best available landscape environmental management knowledge in order to harmonize the ecological, aesthetic, productive and social functions of new valuable landscape, including the recovery of historical continuity and an understanding of ?landscape memory?. The basic landscape functions were assessed on two different scale levels. On a large scale, the relevant attributes were investigated over the whole area of the Sokolov brown coal basin (220 km2). The data and experience acquired were used to define large-scale guiding principles for the rehabilitation of a post-mining landscape. On a small scale, the basic characteristics and functions of the landscape were analysed in the Litov-Chlum model area (2 km2). The information derived from this analysis was used to formulate a small-scale approach for the rehabilitation of the model area and also to define general methodological principles. Keywords: rehabilitation, post-mining landscape, degraded landscape, non-productive priorities

Jan 1, 2004

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By M Sykes

Gold was initially discovered at Ballarat in 1851. After initial alluvial mining, underground quartz mining commenced in 1853, continuing until 1918. The historic miners were considered to be capable of mining anywhere in the world after overcoming the difficult conditions within the Ballarat goldfields. Whilst mining has changed dramatically since the early 1900s the challenges with underground mining at Ballarat have not. Modern pumping systems cope with the moderate water inflows. However, modern machinery and efficient mining methods influence opening sizes and extraction techniques. In some cases modern techniques have accentuated the challenging ground conditions and complex orebodies that were faced by the historic miners. As the Ballarat East project has progressed towards production, technical challenges relating to geomechanics and mine planning are being resolved resourcefully.

Jan 1, 2008

By C. H. Bucknam

Net carbonate value (NCV) characterization methods for acid generation potential measurement originated from studies on the Carlin Trend during the 1990's and have been subsequently standardized through cooperation of the Acid Drainage Technology Initiative Metal Mining Sector and the American Society of Testing and Materials International. The paper describes the evolution and standardization of the NCV methods, the importance of mineralogy in interpreting the results and application of the methods to implementation of the Global Acid Rock Drainage (GARD) Guide.

Jan 1, 2011

By Ren Bryce

The ninth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the SME Annual Conference & Expo in Minneapolis, MN. A total of 33 students presented their work at the contest. The competition began in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes. The students worked hard at their research and then set aside time to complete all the necessary steps to enter the contest. The MPD recognizes the effort required to enter and, as a result, provides monetary rewards to all participants. As in past years, there are separate levels of competition for undergraduates and graduates, and the prizes are designated accordingly. At the graduate level, first place receives $1,000, second place $500, third through seventh $200 each, and all others $125 each. At the undergraduate level, first place receives $1,000, second place $500, third place $250, and all others $125 each.

By W. E. Miller, W. P. Yant, G. W. Jones, R. E. Kennedy

"The determinations of the limits of inflamability of diethyl ether and ethylene in air described in this report were made primarily for comparison with similar determination of other compounds in the same apparatus and by the same laboratory technic. The experimental procedure and the results obtained differ somewhat from those of other investigations. The work also included determinations of the limits of inflamability of these combustibles in oxygen The investigation,was conducted at the Pittsburgh Experiment Station of the United States Bureau of Mines in cooperation with Merck & Co., Inc. LIMITS OF IMFLAMIABILITY OF DIETHYL ETHER-AIR MIXTURESThe limits of inflamability if diethyl ether in air were determined for upward propagation of flame in an upright, closed 8-liter, cylindrical iron bomb 10.2 cm in inside diameter and 96.5 cm in length. This bomb been described in a previous publication. 6Two brands of diethyl ether were used, one a C. P. sulphuric ether manufactured by Baker & Adamson, and,the other Merck & Co. product manufactured for anaesthesia and containing about 3.5 percent of ether alcohol."

Jul 1, 1935

By José María Lezcano, Diego Urquiaga, Pedro Delvasto, Marcos Garayar

La extracción de minerales ricos en sulfuros metálicos tiene el inconveniente de generar drenajes ácidos (AMD), los cuales causan severos impactos en los ecosistemas acuáticos, el suelo y el recurso hídrico. Como posibilidad de remediación (alcalinización) de estos pasivos, en el presente trabajo se propone el uso de coproductos férricos oxidados (CFO). Luego de presentar las características de un tipo de CFO específico, se muestran los resultados —a escala de laboratorio—sobre la respuesta alcalina del mismo, y se discuten las implicancias de estos hallazgos para el tratamiento de los AMD.

Nov 30, 2020

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

By H. Simonsen

Risk assessment consists of a search for the answers to: ?What can happen? ?How likely it is that it can happen? ?What are the consequences if it does happen? Perhaps the most important aim of risk analysis is to predict the likelihood that a planned profit will be achieved over a given period of time. A typical risk model employed for this purpose includes a stochastic connection between the dependent variable of an expression that describes a process and independent variables represented as random quantities. The output will be a probabilistic distribution. The uncertainties in a planned mining operation include: ?Commodity market characteristics, particularly price ?Ore reserves and mineralogical composition ?Mining method ?Process performance ?Capital and operating costs ?Schedule duration ?Economic environment effects. The processes employed in the probabilistic estimation of a project?s outcome include both Monte Carlo simulations and simulations where variable correlation is considered important. The risk model, once developed and tested, provides a framework for a rational approach to risk analysis and the testing of alternatives.

Jan 1, 1999

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By A Chadwick, J de Ross, C Adams

Imagine a æshinyÆ new mine, $1 B in the bank and record commodity prices. So how does a company and its management team create enough tension to maximise profit and to establish a culture that can weather the good and bad times?That was exactly the situation the team at OZ MineralsÆ world class Prominent Hill mine in South Australia faced in 2009.Three years later, the harder times have come - lower though still healthy commodity prices, rising industry costs, fierce competition for talent, geological and technical issues (common to developing mines). However, the company was able to maximise profit during the good times and equip the culture to deal with the tougher times with minimal turnover.Through the combination of simple systems and processes, people development, application of commercial technical acumen and a combination of yin and yang leadership, OZ Minerals has achieved something quite rare - sustainable continuous improvement.The journey started with a vision. The EGM Operations created the æsparkÆ. The dream was to create a æfranchise mineÆ that could be rolled out to new mines and acquisitions as the company grew. However, the real leadership came from his lieutenants who provided the important yin and yang. The GM commercial provided the tools, processes, systems and the bottom line focus. The GM operations focused on culture, leadership, training and sustainability. This powerful combination (along with some good old persistence) was able to create the critical mass required to make continuous improvement go æviralÆ.This paper explores this unique case to uncover the essential ingredients that were created and mixed together. It will touch on the key human, technical and system elements that helped achieve significant improvements in plant recoveries, mine throughput and operational efficiencies, while overcoming human capacity, geotechnical and contractual challenges.CITATION:de Ross, J, Chadwick, A and Adams, C, 2012. How to create a perfect storm, in Proceedings International Mine Management 2012, pp 239-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By AIME AIME

PRACTICALLY all the Section delegates as well as a sprinkling of Institute officers and mere members were on hand for the annual business meeting of the Institute on Monday afternoon of the Annual Meeting. President McAuliffe presided, with C. H. Mathewson as associate chairman. Americo Albala was first called on to discuss the work of the Pan American Institute of Mining Engineering and Geology. C. Will Wright said that the need for such an organization was evident, and a resolution was passed asking the incoming President to appoint a committee to investigate cooperation with that body, of which Mr. Albala is executive secretary.

Jan 1, 1943