Search Documents

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

By Samuel Hoyt

THE writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + ß range, first described in 1913. These notes are offered, not at all as the final explanation of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520° C. and the other at about 600° C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600° C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600°. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + ß range and increased in magnitude with the amount of a up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + ß field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 12, 1918

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016

By D David

Amongst those whose task it is to design tumbling mills and other comminution machines there is an almost religious divide between devotees of the Bond method and devotees of other methods developed in more recent times. For a decade or so the issue was between the Bond power-based methods and the JKMRC (JK) simulation based approach. The newest method to challenge the status quo is power-based and was developed by Steve Morrell. As the title suggests, this paper will take some liberty at concluding that Fred Bond and Steve Morrell may be separated by history, but not by their approaches to their individual contributions to the science of comminution. Another driver for the paper is that although it is good to have diversity of thought, the existing divisions are problematic for those of us signing public disclosure documents. If alternative design methods produce materially different outcomes for the mill duty, then at least one of them is wrong or being used incorrectly. At some point the unsustainable argument may need to be put in a court of law that we metallurgists have two or more materially different design methods, each of which is correct! Therefore, perhaps a resolution is needed before this occurs?The works of both Fred Bond and Steve Morrell are each directly related to their contemporary grinding mill design and operational environments. Both their approaches are empirical, borne of observing and measuring real world situations. Both worked with theories that preceded them, gathered their own data and then each saw shortfalls in the status quo.Fred Bond was an escapee from revolution, a victim of The Great Depression, and had several near death experiences during his early site-based career. Perhaps he was fortuitously rescued from himself when asked by Allis Chalmers (A-C) to set up its rock testing laboratory in Milwaukie in 1930. Fred’s testing led him to conclude that neither the Kick nor the Von Rittinger theories explained his measurements. His writings on the failings of these old theories caused a divide between devotees of the old and new methods at that time. After many years, and much thought and plotting of data (the old way!), he came up with his now-famous equations (and his Third Theory) which have stood the test of time, certainly in the world of Bond-era machines.Coming from England via several African diamond mines, Steve Morrell immersed himself into the comminution world of the JK in Brisbane about a decade after Fred passed on. The JK had developed its semi-autogenous grinding (SAG) simulation framework using its own pendulum breakage tester, itself a derivative of the twin pendulum impact device invented by Bond decades earlier. At the JK Steve developed his authoritative Tumbling Mill Power equations and was involved in real world analysis of comminution problems on the global stage. Steve’s JK experience coincided with the demise of the rod mill, the rise of autogenous grinding (AG) and SAG milling and a rapid expansion in concentrator capacity.Morrell left the JK to pursue his own interests, which included ongoing consulting work, now demanded by the comminution world. He then turned to investigating a growing list of discrepancies between the opinions of designers and theoreticians, and the factual outcomes. The Morrell Method of design arose from this re-examination of ore testing, real world operating data and these glaring and expensive discrepancies between design and outcome. The elements necessary for a relook at the world of rock breakage were in place!CITATION:David, D, 2017. Steve and Fred would have been mates – a comminution design evolution story, in Proceedings MetPlant 2017, pp 2–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Javier Támara

Para aumentar la productividad de la empresa minera es necesario conocer el sistema de aire -en tanto se prioriza los intereses de los clientes, y así se puede suplir todos los componentes necesarios para garantizar una máxima eficiencia y confiabilidad del sistema completo de aire comprimido que va desde el filtro de admisión hasta el punto de uso. En ese sentido, el presente texto describe las estrategias para realizar Solucionazing en ahorro energético y así aumentar la produtividad de los sistemas de aire.

Aug 25, 2002

By John E. Lens

Driving bridge foundation piles into glacio-fluvial sands and gravels and glacial tills brought surprisingly longer than predicted driving lengths on several recent projects in Vermont. In some instances, piles drove more than 40 feet past refusal depths predicted from Standard Penetration Resistances from borings terminating in glacial till. Overall, piles developed substantially less skin friction than predicted using common capacity formulas and drove as much as 80 feet longer than predicted in the moderate to dense gravelly and cobbly soils. These piles were driven for one to five span highway bridges within narrow valleys with bedrock ranging from 80 to over 200 feet deep. Piles were for both conventional and integral abutment bridges. H-piles were used for a variety of reasons including lower unit cost, better availability, and better ability to drive through cobbly soils in upper strata. Dynamic testing was used to evaluate capacity, including skin friction and end bearing capacity. In order to develop better pile length and capacity predictions for future projects, VTrans and one of their geotechnical consultants are collaborating to develop criteria for improved pile capacity predictions in these river valleys. We are doing this by evaluating driving and dynamic testing data from four projects in comparison with the Federal Highway Administration (FHWA) DRIVEN pile design software, and methods from Myerhof (1976) and Tomlinson (1981). Our overall objective is to provide a basis for choosing appropriate pile types and reliably estimating pile lengths for projects in this terrain. Bridge foundation design projects in other mountainous terrain share similar design and construction challenges to those encountered in these Vermont projects. These include: difficult exploration drill rig access requiring smaller rigs with limited capability to drill through cobbles and boulders deep enough to reach bedrock; limited experience with displacement piles as alternatives to H-piles in this geology; and relatively greater variability in soil stratigraphy between foundations at these sites as a consequence of the relatively high energy depositional environment in mountainous terrain. This paper presents the case history summaries of the pile driving, results of the ?back analysis? capacity evaluations, examples of solutions employed on these projects to address the lower capacities achieved, and resulting pile capacity design guidelines and prediction criteria for these geologic conditions based on data from these projects.

Jan 1, 2007

Using the philosophy that 'change cannot be introduced through memos-you have to get people emotionallyinvolved', SRK's Environmental Group in South Africa is helping clients communicate their environmental management objectives more effectively through the powerful medium of interactive industrial theatre. Existing and pending environmental legislation, international pressures, and growing awareness of the environment have led South African industry to the point where responsible care, for both the environment and the health and safety of those affected by the activities of an industry, is now a focus of management policies.

Jan 1, 1995

Gold rooms represent a high security area and preventing theft is a challenging task. Where gravity concentrates or high value unit intermediate products are present, particular and specific security procedures must be put in place. This paper describes the development and implementation which reflects best practice in gold room security. Procedures involving key holder systems, key locks, swipe cards and double locks preventing any one person having access to the gold room, including specific procedures for gravity gold concentrators, will be addressed. The use of monitoring and how to deal with alarms and potential hold ups will be reviewed. The use of cameras and archival DVD recorders is common in gold rooms. The use of electronic surveillance, movement detectors, seismic monitors and the two person policy and gold room entry procedures are described, including how to deal with visitors. The importance of confidentiality regarding smelting and gold pick-up days, plus strategies employed to minimise storing large quantities of gold on site will be presented. The role of metallurgical accounting in providing quality auditable information and the minimum standards of record keeping required is discussed. The role of the Gold Squad will be outlined. Regular auditing and risk analysis and several case studies are cited where security was deficient or improved.

Aug 1, 2010

By Ben Murphy, Alejandro Yanez, Tatu Miettinen

"Flotation using large volume cells has grown in importance during recent years, particularly given the increasing demand for minerals whilst ore grades are decreasing. Outotec introduced the TankCell® e300 in 2007 to enable concentrator plants to process these higher tonnages. From the beginning, TankCell® e300s with FloatForce® mixing mechanisms have demonstrated good metallurgical performance with decreased operating costs and high availability. This paper deals with specific engineering challenges that need to be considered when installing these units rather than giving examples of performance. Today there are over 100 TankCell® e300s operational worldwide. As more of these units are installed new technical challenges are encountered and solutions developed to maximize their productivity. Lessons have been learnt by operators, engineering companies and the cell manufacturers on how best to design and layout these cells in modern concentrators to ensure smooth transition from design to installation to operation. This paper presents information on important design considerations and learning that has been obtained through the design, installation and commissioning of the TankCell e300 around the world. Areas pertaining to cells layout such as feed and discharge arrangements along with items of metallurgical concern such as sampling, reagent addition and the potential benefits of installing a variable speed drive on the motor will be covered in depth."

Jan 1, 2014

By B. K. Cantrell, D. H. Carlson, W. F. Watts, K. L. Rubow

The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH) regards "whole diesel exhaust" as "a potential occupational carcinogen." Threshold limit values (TLVs) are recommended for the gaseous pollutants CO, CO2, NO, N02, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality. Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulageway and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2 and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters. Concentrations of CO, C02, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3.

Jan 1, 1992

By Georgene Renner, William R. Yernberg, Steve Kral

Agapito Associates (AAI) provides consulting services in geo-engineering, mining engineering and related disciplines. Founded in 1978, the firm operates out of offices in Grand Junction, CO, Golden, CO and Lombard, IL. Members of the staff include mining, civil and geological engineers, physicists, geologists, numerical analysts, computer specialists, instrumentation specialists, plus administration and technical support personnel. AAI has provided consulting and engineering services to mining companies producing base metals, precious metals, coal, potash, trona, limestone, oil shale and salt, and to defense and nuclear-waste disposal industries. AAI also provides services for measuring in situ horizontal stresses using an advanced biaxial overcore stress downhole measurement system developed by Sigra of Australia. Since 1978, AAI has measured in situ stress in copper, oil shale, molybdenum, trona, limestone and coal mines, and in tunnels and concrete structures. Since 1994, the staff has completed 527 overcore stress determinations. AAI has the equipment and personnel for overcoring, sample coring and instrumentation installation in limited access, surface and underground mines. Portable Longyear CP-65 drills, borehole deformation gauges and strain indicators are used for difficult-access overcoring and are permissible for use in gassy mines.

Jan 1, 2006

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001

By J Taylor, A Dubowik

To increase the efficiency and improve the quality of diamond drilling at Olympic Dam, mine geologists have adapted and modified common practices in order to overcome the challenges imposed by such a unique environment. Mine geologists have to take into account both the complex geology during the diamond drill hole design phase, as well as incorporating diamond drilling into the larger-scale scheduling process already employed at Olympic Dam. This study seeks to explore how such modifications have evolved over time.The geology of Olympic Dam influences the design process of diamond drill holes, particularly due to the variation of lithology and alteration, as well as the presence of magnetite and major structures within the orebody. Exclusion zones are used to manage interactions with existing and planned mining activities, and their size is dependent upon the geology of the area. Specific deviation checks are used to monitor the deviation of diamond drill holes with respect to these?zones.The highly interactive environment of Olympic Dam requires unique planning for diamond drilling, resulting in the production and implementation of both long- and short-term schedules. Long-term schedules are targeted at determining drilling locations and ensuring drilling is completed prior to stope planning, while short-term schedules aid in enabling access to ensure timely set-up of drill sites. Estimated drilling rates, determined by expected lithologies and historical data, feed into the short-term schedule to assist in managing the operation and minimising the downtime of diamond drill rigs. A mine geologist is appointed as a diamond drill coordinator to organise and manage diamond drilling at a scheduling and operational level, streamlining the entire process.Analysis of historical data shows a strong correlation between implementation of the aforementioned practices and improved drilling rates. This study shows the importance of adapting universal tasks to particular environments and circumstances. Mine geologists at Olympic Dam continue to acquire knowledge to further improve the modified drilling practices as operational requirements, production pressures and economic factors change.CITATION:Taylor, J and Dubowik, A, 2014. The evolution of diamond drilling practices at Olympic Dam, in Proceedings Ninth International Mining Geology Conference 2014 , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By T. S. Fuller

MUCH study has been given by engineers in general, and investigators in particular, to the concentration of stress which occurs under load in structural members having irregularities in section such as notches, shoulders, key ways, tool marks, etc. The result of the effect of both fresh and salt water corrosion upon the endurance properties of various metals and alloys has been ably determined and the general laws underlying these phenomena carefully pointed out by McAdam. From a practical standpoint, 'however, it is after all the endurance value of corroded, non-symmetrical sections which is most pertinent. In the experiments about to be described rotating cantilever specimens of nickel steel of the 3.5 per cent nickel ' 0.35 per cent carbon type have been used. These were machined from bars l 1/8. in. dia. and 9% in. long and were heat-treated by quenching in oil from 825 deg. C. followed by reheating to 650' C. and oil quenching. The tensile and impact properties of this material so heat- treated follow:

Jan 1, 1931

By J Carter, B J. Armstrong

Best practice for the submission of samples to an internal or commercial laboratory requires quality control materials to be included for the purpose of independently and comprehensively assessing laboratory performance. These quality controls include the use of certified reference materials (CRMs) and may be blind to the laboratory. Iron ore companies purchase these materials from reputable manufacturers from stock of run-of-mine materials at the appropriate grades. The international standard, ISO 17034 (ISO, 2016), specifies the competency requirements for organisations manufacturing reference materials, and includes rigorous requirements for the assessment of homogeneity, stability and establishment of property values and their uncertainties. Homogeneity is one of the most important measures of suitability for all certified reference materials and refers to the degree to which the composition and properties of a sample are uniform throughout the batch, relative to the analytical precision of the method. More specifically, homogeneity studies of candidate reference materials should be assessed for both within sample variance and between sample variance with appropriate statistical controls. The design and application of homogeneity studies are discussed as they apply to both crushed and pulverised reference materials. Crushed certified reference materials have been utilised by the iron ore industry for a number of years and provide the user with a critical assessment of variances in sample preparation in addition to analysis. Crushed reference materials are similar in presentation to an RC sample and are generally used as discrete parcels of material submitted to the laboratory from the field. Pulverise certified reference materials miss the sample preparation step and are subsampled from th delivered sachet at the point of analysis. This paper compares the relative homogeneity performance of crushed and pulverised certified reference materials by grade across key iron ore chemical constituents. Outcomes are benchmarked to the international standard ISO 9516 (ISO, 2003) for the determination of various elements in iron ores by lithium borate fusion and X-ray fluorescence. Practical implications are discussed with reference to a case study from an iron ore laboratory in the Pilbara.

Sep 18, 2023

By A. M. Tonnos

Underground mining has yet to see an industry wide solution for control of their ventilation systems due to the complexity and sensitivity of the underground environment. Complexity arises from multi-level, multi-zone operations and sensitivity is associated with the impact that changes in equipment status and output have on air flows and quality throughout the mine. Our approach to solving this challenge incorporates system modeling and industrial control systems in a unified architecture. Although this approach can be applied to other processes and industries, this paper will cover the theoretical and practical aspects of an integrated model-control system (MCS) as it applies to underground mining ventilation.

Jan 1, 2009

By M J. Davies, R S. Davies

Despite increased expenditure, the global discovery rate of world-class ore deposits has been in decline for over a decade (Schodde, 2017). Mineral exploration has traditionally followed an empirical approach, searching for evidence of mineralisation upon the surface of the planet, then drilling to define the extent of an ore body beneath the surface. As outcropping deposits in well-defined areas are depleted, there is a need for exploration to extend to less well-explored search spaces. One popular new frontier is exploration at greater depths beneath the Earth's surface. However, exploring for deep deposits with limited surficial evidence requires the implementation of predictive targeting methodologies (Hronsky, 2011; McCuaig & Hronsky, 2014). The Mineral Systems Concept (Hronsky & Groves, 2008; McCuaig et al., 2010) provides a framework for predictive exploration targeting. Ore deposit formation is recognised to be a focused mineralising event. These events represent self-organising critical systems and are underpinned by the interaction of complex, non-linear processes. Through the collection and analysis of datasets that map mineralising processes, it may be possible to predict the size and location of resultant ore bodies. CITATION: Davies, M J and Davies, R S, 2018. Beyond below-ground geological complexity: Developing adaptive expertise in exploration decision-making, in Proceedings Complex Orebodies Conference 2018, pp 95–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M. Wright, A. H. Mwale

This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered.

Jan 1, 2003

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959