Search Documents

ALTHOUGH the open-hearth charge contributes CO, C02, H2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion; the latter then is regarded simply as the source of the net heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were accomplished by blowing in air or oxygen, as in the bessemer converter, the net heat absorption would be negative; that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. - In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000 F (1600 to 1650 C), so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTING In a typical heat, the fuel furnishes about four million British thermal units per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner but it ranges downward from about one million Btu, depending not only on the charge but on the manner of calculation. In any event, this requirement appears small in comparison with the

Jan 1, 1951

By A. Landsberg

Kaolinitic clays are potentially a vast domestic resource for aluminum. Utilization of this resource could decrease or eliminate the nearly complete dependence of the United States on foreign raw materials for this important metal. Furthermore, processing of clay to aluminum through anhydrous chloride metallurgy could reduce the high electrical energy requirements of the conventional Hall-Heroult aluminum reduction process. Several anhydrous chloride processes have been proposed; however, unresolved technical problems have prevented their commercialization. In particular, an acceptable chemical means has not been found to extract aluminum from clay as a highly pure anhydrous aluminum chloride. This Bureau of Mines report identifies and discusses the important chemical problems involved in achieving an acceptably rapid, self-heating, selective chlorination reaction and the subsequent separation of iron chloride byproduct from the anhydrous aluminum chloride.

Jan 1, 1983

By Chen Bing Ching

Hsikwangshan mine is located at Lengshuijiang city of Hunan Province. It is a stibnite deposit. The orebody is gently inclined; its ore run is about 3 km in length and extends about 1.2 km along the direction of dip. The thickness of the ore body is non-uniform and varies from 1.5 to 20 m. The orebody is mined by room and pillar and cementation filling. The nine levels at the ore top have been mined out. At present, the mining operations are at the eleventh level. The mine ventilation system consist of three main fans which are installed in different shafts and are ventilated in parallel. The main fans can be connected to each other through comprehensive return air drifts. Two of the fans are located underground and the other on the surface. The general configuration of the ventilation system is shown in Figure 1. Because the operating areas are scattered and vary frequently as well, it is difficult to bring about air flow control. If the air flow cannot be varied with the variation of production in time, the air quantities are not sufficient in some areas and are excessive in others. However, it is also a problem to coordinate the three main fans with one another to obtain the optimum economic cost of operation. In order to make the air delivery fit the variation of production continuously to satisfy the ventilation requirement of the working faces and to reduce power consumption, we have made a great effort over five years to install an automatic control system for mine ventilation at the Hsikawangshan mine. The key part of this system is a microcomputer. The whole system consists of a console, which is located at the surface; the circuit network that is provided for signal transmission; air doors and ventilators at the working face; the scale air doors which are installed at the main branch airways; main fans and their speed regulating devices, as well as the sensors used for observing pressure, air quantities, temperature and the concentration of carbon monoxide, etc. This system can continuously telemeter the air quantities and carbon monoxide concentration in the main branch airways, air pressure, air quantities, electric current, the temperature of the bearings of the main fans, etc. According to the production air requirements, the system controls the ventilators or air doors which are located at the working faces and regulates the air quantity in the main branch airways. It can also choose the optimum mode of operation automatically, and regulate the rotating speed of the main fans to guarantee the least total power consumption while satisfying the total air quantity requirements. If abnormality of the observed results is discovered, the audible and flashing light alarm signal starts up automatically. The operating mode of ventilation equipment also feeds back to the control room and displays on the console. The configuration of control the system is shown in Figure 2.

Jan 1, 1987

By K Pery, J Leahy

Established metallurgical plants operate in a complex environment of interdependent drivers including technology change, operating and maintenance practice, evolving markets, HSEC requirements, statutory and plant requirements, personnel turnover, ore supply, and financial conditions, to name a few. A successful optimisation program should comprehend these factors and drive towards not only lower operating costs, but also higher rates of return for a given level of investment. Optimisation programs have the potential for very high rates of return on capital that Greenfield projects rarely have. This paper presents a robust strategy and methodology for plant optimisation initiatives as well as a case study of how it was implemented at the QNI Yabulu refinery in Queensland, Australia by an integrated team of researchers, engineers and operators. The methodology is premised on the fact that nobody knows the production asset as well as the current operating team. It covers the optimisation process from ideas generation, various stages of selection against the agreed criteria, development, including testwork, funding approval and implementation. It highlights the benefits in the use of integrated teams, the establishment of a sound project basis, and a diligent, phased approach.

Jan 1, 2004

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By J. Tang, B. Q. Li, R. Akarapu

"An integrated model is developed to represent the three-dimensional electromagnetic wave propagation and thermal phenomena during microwave heating of ceramics and dielectric/biological materials. The model development is based on the edge finite element formulation for electromagnetic fields and the node fmite element formulation for thermal phenomena. Results are presented and compared well with available analytical solutions and experimental measurements. With the model, the effect of sample positions on the electromagnetic and thermal field distributions is studied.IntroductionMicrowave, as an electro-heating source, has been widely used in the processing industries for packaged foods and other materials. The commonly used household microwave oven is a typical example of microwave heating processes. Other industrial microwave processing systems include large-scale microwave guides and cavities, which are used for the sintering operations as required for making ceramic components or for sterilizing the packaged foods."

Jan 1, 2004

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By \/eena Sahajwalla, Alexander Blagus

This paper reports the effect of using High Density Poly-Ethylene (HDPE)/coke blends on the reduction behaviour of Mn3O4 to MnO at 1000°C. The results suggest that CH4 release increases with increasing HDPE addition. The results show that the rapid release of methane, over only the initial five minutes, limited the interaction of Mn3O4/MnO with CH4. With the devolatilisation of HDPE there was increased porosity in samples containing HDPE, assumed to be the major factor in differences of reduction rates.

Jan 1, 2011

By Edgar L. Weinberg, W. Horatio Brown

The Austinville-Ivanhoe lead-zinc deposit occurs in the Lower Cambrian Shady dolomite. This deposit is located in southwestern Virginia in the faulted and folded Appalachian Valley and Ridge province. The ore bodies resemble the chimmey and manto deposits of northern Mexico and are formed by replacement and filling. They are confined to certain favorable zones of the Austinville and Ribbon members of the Shady. Structural and stratigraphic factors combine to control the location and form of the ore bodies. In certain places secondary oxide enrichment of the zinc minerals has contributed to the economic development of the area. It is concluded that the ore is epigenetic and is deposited by hydrothermal solutions rising through the fault "plumbing." Classification is epithermal-telethermal.

Jan 1, 1968

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By AIME AIME

A DOCUMENT of progress and of great interest to engineers is the report of the Military Affairs Committee of 'the Engineering Council, which has just been accepted and sent to the secretary of War. It provides .a plan whereby civilian engineers holding commissions in the Reserve Corps may; with their con- sent, be called into service of the army during peace at any time, either with troops in the field or in a consulting capacity on any government engineering work. The Military Affairs Committee finds ample authority in the military bill passed by Congress on June 4, 1920, for this arrangement and also for extending the privilege to military engineer, officer-s of the regular army to engage in civilian work during times of peace. It is hoped that the Secretary of War will adopt the suggestions and put the program outlined into effect. This is a constructive piece of work comparable to the efforts of the military Committee before the war which developed so much in the way of preparedness, particularly in the program of military lectures which, held in the auditorium in the Engineering Societies Building, became so popular that each lecture had

Jan 1, 1920

By M. F. Dunn

A handbook to provide a quick reference guide for selecting and using jet fans in a variety of conditions was prepared. The document is intended for use by front-line supervision, ventilation engineers, and mine planners. Included are discussions of jet fan characteristics, selection and use critieria, and do's and don't's for easier operation, safety, and performance. The handbook is based on research at three underground metal/nonmetal mines having cross-sectional areas of 900 to 2,000 ft2.

Jan 1, 1983

By Oleg I. Platonov

Method of high-temperature reduction of oxygen-bearing sulfurous gas has been developed at Copper Plant (CP) of MMC ?Norilsk Nickel? Trans-Polar Division (PD) with the aim of producing elemental sulfur from Vanyukov furnace? off-gas. Non-explosive reduction technology of oxygen-bearing sulfurous gas by methane utilized at Copper Plant has been designed to separate the processes of gas heating and sulfur dioxide reduction based on different kinetic of the reactions oxygen fixing and SO2 reduction. First, natural gas promptly reacts with oxygen contained in the process gas to heat a gas mixture up to the temperature of sulfur dioxide reduction (1200C). Then isothermal reduction takes place within 1 sec. Combustion chamber (pre-chamber) design developed based on the above principles is presented. Practical experience of the two reduction reactors operation at CP since 1996 proves high efficiency of the developed reduction process. The volume efficiency rises dramatically thanks to the fact that both fuel and reducing agent are fed into the reactor volume in the form of high-speed turbulent jets providing an intensive mixing of the reacting gases. On condition of equal internal volume of the reactors, the developed process offers higher efficiency of reagent interaction resulting in sulfur conversion exceeding 90%, as compared to the equilibrium one.

Jan 1, 2006

By L. V. Wade

The use of longwall/shortwall mining systems is under increasing scrutiny by the U. S, coal industry as a means to reverse the decline in productivity. The success of these mining systems depends to a great extent upon designing the system hardware to best suit local conditions. Of particular importance in this regard is designing the various elements of the total ground support system, including face, face end, and gate road supports, to accommodate local geologic conditions. This presentation centers on the problem of selecting the face support system. The existing geologic situation can influence the selection of the face support hardware in a variety' of ways. In general terms, these influences can be grouped into the following four areas: 1. The capacities required of the support unit; 2. The roof, coverage supplied by the support units; 3. The flexibility required of the support unit to meet changing geologic conditions; and 4. The required stiffness characteristics of the individual support units both vertically and horizontally. The following will center on the first area, i.e., the required d capacities of the support unit, in particular, the maximum required load density for a particular geologic situation.

Jan 1, 1976

By A Hacket, M Haest, I Vitins

Infrared spectroscopy has the ability to accurately measure mineralogy of drill cores, allowing for better spatial characterisation of iron ore deposits and potentially improving the prediction of key mining and processing parameters at the deposit scale. BHP Billiton Iron Ore is using infrared spectroscopic drill core logging to provide fast and accurate mineralogy for diamond cores and reverse circulation (RC) samples.Mineralogy can be predicted from infrared spectroscopic drill core data with errors on estimates ranging from six to 12 weight per cent. The error on the clay estimates is significantly lower than for hematite and goethite content estimates. This manuscript presents the results from a study on a bedded iron ore deposit, hosted in the Brockman iron formation, for which infrared spectroscopic data were collected on all of the diamond and RC drilling. Results show that these mineralogy estimates improve drill core logs, the geology model and the metallurgical block model.CITATION:Haest, M, Vitins, I and Hacket, A, 2013. Infrared spectroscopic drill core logging - making inroads to deposit scale 3D mineralogy, in Proceedings Iron Ore 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Koch D. F A

An electrochemical study of the dissolution of gold in aerated cyanide solution shows that the dissolution rate is determined by the nature of the surface. A passive film (probably a basic cyanide) formed at -0·6 V vs a saturated calomel electrode inhibits both the anodic dissolution of gold and the cathodic reduction of oxygen. Thallium has an "activating" effect on these reaction mechanisms.INTRODUCTIONIn general the dissolution rate of a solid in a liquid is studied by weight loss measurements or analysis of the solution at known time intervals. However, if the solid is a metallic conductor, on which a redox reaction can occur at the metal-solution interface, it can be studied by electrochemical techniques. Electrochemical measurements have the advantage that the overall reaction can be separated into its components, in some cases by electrical measurements alone, and in others by a combination of these with analytical determinations.The overall equation for the dissolution of gold in aerated cyanide solution may be written4Au + 02+ 8CN- + 2H20 = 4Au (CN)2- + 40H- ..... (1)which can be separated into the two electrochemical componentsrepresenting the oxidation of gold and the reductionof ogygen respectively.4Au + 8CN-,= 4Au(CN)2- + 4eand O2+ 2H20 + 4e = 40H- These two reactions occur at the gold-electrolyte interface and it is the purpose of this paper to discuss the mechanism...

Jan 1, 1964

By M. Khandrika, B. K. Parekh

Column flotation has proven to be the most effective technique for the flotation and recovery of ultrafine coal. The commercial application of columns in the coal industry is steadily increasing (Parekh et al., 1990; Yoon et al., 1992). For the flotation of coal or mineral air is used for generating bubbles. Using a conventional flotation cell, Miller and Mishra (1985) compared froth flotation behavior of fine coal using air, nitrogen and carbon dioxide gas. They concluded that carbon dioxide gas provided a higher rate of recovery and a lower ash content. The objective of the present study was to investigate the effect of various gases such as compressed air, nitrogen, argon, and carbon dioxide on the column flotation of fine coal.

Jan 1, 1999

The investigations of the Leningrad ruining lilstitute on this problem are carrying out in the following main directions: 1) The analysis and study of contaminants migration at particular sites of mining development; 2) The working out of theoretical and me- thodical basic principles of aquifers migration tests; 3) The work- ing out of methods of the forcasting of groundwater pollution pro- cesses; 4) The theoretical and uethodical substantiation of hydro- geological observations of groundwater pollution processes; 5) The wort ing out of the measures at the groundwater control and their rational use at the particular sites of mining development. The research that have been carried out by the present moment have covered the wide range of wining and geological conditions -- as from the point of view of specific genetic types of water-be- aring rocks (porous, fissured and fissured-porous), as well as from the point of view of pollution sources (surface waste water basins and underground basins of non-standard water) and the cha- racter of the latter's migration (tracers, physically neutral ef- fluents, heavy or light ones). The combination of specialized mi- gration tests and observations carryed out at uoayi, sites, as well as the following ar~,alysis o:i the data of field study allowed to get useful theoretical, methodical and practical results on the all directions above mentioned, ns the summing up of these results the author proposed the concept of controlled ground :ester polluti on. This conception is based on three whales" - groundwater self- purification, engineering prevention measures and ground-water monitoring correlated with each other by succes i.vely refined (ac- cording to the observation data) hydrogeologicZl forecasts.

Jan 1, 1988

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968

By Dharmil Patel, Michael J. Chow

"Construction progress is nearing completion at a Brownfield Site for a 100,000sf mixed-use 10 story building plus cellar for Silver Star Motors including a two-floor pre-owned Mercedes Benz showroom; high-end residential rental studios, 1, 2, and 3 bedroom apartments; and penthouses on the upper two floors. Excavation through impacted soil extended to 15ft depth. Project is approximately 7 ft north of a NYCT subway station, portions of the SOE are within inches of a 6ft diameter NYCDEP Sewer, and cellar extends below the depth of adjacent structures, requiring over 200 lf of underpinning.A complex series of earth retention systems was utilized consisting of underpinning, drilled-in soldier piles (micro-piles), timber/concrete lagging, soil anchors and inclined rakers supported by a partially constructed foundation mat. Foundation mat subgrade was approximately 4 ft below the groundwater level creating more challenges during underpinning and achieving suitable foundation subgrades. All construction was undertaken on a non-union basis.This paper describes the design, construction, and lessons learned for the multiple earth retention systems, Brownfield Remediation requirements, instrumentation, and monitoring used to manage complications of building adjacent to an active subway station, in close proximity to existing utilities, with underpinning and mat foundation installation below the water table.Results of the instrumentation program are summarized which utilized an AMTS, monitoring prisms on adjacent structures, automated seismographs, and manual NYCT surveys."

Jan 1, 2016