Search Documents

By K. A. Semlak, F. N. Rhines

NFILTRATION is a term used to designate that i- process by which the pores of a metal powder are filled with a relatively low-melting liquid metal through the action of capillary forces. This is accomplished in practice either by heating the porous body in contact with the solid infiltrant metal above the melting point of the latter, or by preheating the porous body separately and then dipping it into the liquid metal. The liquid, as it sweeps through the porous body, replaces the gases progressively, thus yielding a relatively dense product in a short time.' Liquid-phase sintering, which is related to infiltration, is a process by which a mixture of two or more metal powders is sintered at a temperature between the liquidus and solidus of the ultimate alloy.' According to Cannon" liquid-phase sintering can be divided into three stages which he calls liquid flow, accommodation, and solid sintering. The largest density increase occurs during the first stage, where the lower melting component melts and, driven by capillary forces, flows among the particles of the higher melting component, where, after dissolution of the bonds between the solid particles, it moves them into close packing. This happens so quickly that little has yet been learned of its mechanism. A study of the rate of capillary rise of a liquid metal in a higher melting metal-powder compact may be expected, therefore, to contribute not only to a firmer understanding of the process of infiltration as such but also to a more extensive knowledge of what occurs during the initial stage of liquid-phase sintering. Theoretical Basis In order to derive a mathematical expression of the rate of infiltration, it has been assumed that a powder compact consists of a great many parallel capillary tubes and that the rate of rise of a liquid in an average capillary channel represents the rise in the entire compact. For a straight capillary, assuming that Poiseuille's law obtains for the non-stationary state and that wetting is very rapid, Ligenza and Bernstein' have derived the following differential eauation of motion where h is the height of rise of the column of liquid at time t, R, is the radius and 1 the length of the capillary, t) and 7, the viscosities of liquid and air, respectively, p and p, the density of the liquid and air, respectively, y the liquid-gas surface tension, 0 the liquid-solid contact angle, and g the acceleration due to gravity. The term on the left of Equation [I] represents the rate of change of momentum of the contents of the capillary tube. On the right the terms represent, respectively, the forces due to a) surface tension, b) viscous resistance, c) gravity, and d) end-drag effect. Equation [I] is not amenable to explicit solution, but for a tube of sufficiently small radius, the rate of rise may be slow enough so that the rate of change of momentum and end-drag terms may be neglected. The validity of this simplification was established by Ligenza and Bernstein' by graphical differentiation of observed data obtained from organic liquids rising in glass tubes. The solution of this simplified case is:

Jan 1, 1959

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By Valtemir Coelho Rodrigues

Nos últimos anos face a quantidade significativa de reparos gerais, parciais e emergenciais no revestimento refratário dos fornos em um curto período de tempo (média 02 fornos por ano), haviam paradas prolongadas dos fornos de cal para execução destes reparos onde era necessário prever todos os anos um alto valor para compra de cal, revestimento refratário e mão de obra de manutenção refratária. Afim de reduzir estes custos, aumentar a disponibilidade e produtividade dos fornos, foi feito um estudo e análise para detectar os problemas para serem tratados. Chegamos a conclusão que para aumentar a campanha dos fornos era necessário manter um ritmo estável de produção para evitarmos os choques térmicos no revestimento, treinamento da contratada e implantação do novo projeto para realização de limpeza dos canais o que eliminava o impacto de alavancas contra o revestimento, revisar o projeto o que mudaria a geometria e a composição de algumas peças refratárias, aperfeiçoamento dos monitoramentos do revestimento dos fornos para identificação mais rápido das ocorrências de problema de forma a permitir a aplicação de técnicas corretivas de maneira eficiente além de um intenso trabalho junto ao quadro operacional incluindo cursos e melhorias nos procedimentos que impactavam diretamente na operação correta dos fornos, além disso, melhorias significativas de manutenção contribuíram para melhor performance dos fornos de cal. É possível checar os resultados que este projeto proporcionou aumentando em 06 anos no mínimo a campanha dos fornos eliminando os reparos parciais e emergenciais realizando somente reparos gerais além da redução de custos.

Aug 17, 2017

By X Hu, C-C Yang, J Pan

In this work, preheating and roasting tests of pellets made from blends of Western Australia ultra-fine (WAU) magnetite concentrate and Chinese domestic magnetite concentrate or Brazilian hematite concentrate were carried out. The results showed that pellets made from 100 per cent WAU magnetite concentrate possesses inferior preheating and roasting performance when preheating at 1050°C for 20 minutes and roasting at 1300°C for 40 minutes, the compressive strength of preheated and fired pellets is 502 N/pellet and 2313 N/pellet, respectively. When 40 per cent Chinese domestic magnetite concentrate or 20 per cent Brazilian hematite concentrate was blended with 60 per cent or 80 per cent WAU magnetite concentrate, the appropriate preheating temperature of the pellets are reduced from 1050°C to 950°C and 975°C, and also the firing temperature of two types pellets are decreased from 1300°C to 1250°C and 1280°C respectively. Moreover, the compressive strength of fired pellets is obviously improved up to 2746 N/pellet and 2630 N/pellet respectively. Microstructure analysis of the fired pellets made from 100 per cent WAU shows its poor growth of Fe2O3 grains, low interlinkage degree of hematite grains, small size of crystallised grains and high porosity of pellet; however, the fired pellets that blended with domestic magnetite concentrate or with Brazilian hematite concentrate have fully growth of Fe2O3 grains, closer interlinkage of hematite grains, lower porosity and stronger consolidation. The preheating and roasting performance of WAU magnetite concentrate pellets can be improved by optimising ore matching.CITATION:Pan, J, Hu, X, Zhu, D-Q and Yang, C-C, 2017. Pelletising performance of Western Australian ultra-fine magnetite concentrate and strengthening technique by optimising ore matching, in Proceedings Iron Ore 2017, pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems in¬clude: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of en¬vironmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental dif¬ficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 1, 1980

By R. B. Dunn

Whilst coalmining in the United Kingdom has been synonymous with longwall mining practice there have been changes in recent times which have enabled not only an extension in the length of the face to be worked but also in the ability to extract both thick and thinner seams. Additionally the industry has taken a positive view in the extension of retreat methods of extraction applied for different reasons both to particularly thick and specially thin seams. To permit development of a flexible programme to meet these diverse needs, it has been necessary to design machinery along with mining systems specially suited to these requirements. In reviewing current UK thinking special emphasis is made on the extraction of thinner seams generally of higher quality coal at moderate depths with a commentary on some recent results.

Jan 1, 1979

The validity of a steady state assumption made by Adams and Nicol (1986) in the modelling of the elution of gold from activated carbon was investigated. It is shown that the accuracy of the steady state approximation is dependent, not only on the magnitudes of the solution flow rate and reactor volume, but also on the lumped elution rate constant. Under the experimental conditions used by Adams and Nicol (1986) the steady state assumption was inaccurate. This could be circumvented in this instance by applying a rigorous general model which accounts for unsteady state behaviour in the solution and in the activated carbon to the experimental data.

Jan 1, 1997

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By J. E. Kemp

1. Situation.—From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway. which connects Monterey with Tampico. follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares. and from Linares one can see far away to the southeast the peaks of another group of mountains rising from the general plateau and forming a more eastern

Jan 1, 1906

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems include: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of environmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental difficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 9, 1980

By Toshia Ishii, Jun Kubota, Noriko Kubo

"For steel continuous castings, it is essential to control molten steel velocity at the meniscus, since the velocity is closely related to surface defects on the resultant products. Argon gas is supplied with molten steel into the mold through the submerged entry nozzle to prevent nozzle clogging. In this study, to investigate the influence of argon gas on molten steel flow, a numerical simulation was carried out by a two-phase model. Simulation results indicate that as argon gas bubbles ascend near the nozzle by their buoyancy, they induce the molten steel flow with them and resulted a meniscus molten steel flow from the nozzle to the narrow face of the mold. This flow direction is opposite to the case without argon gas. The calculated data are compared with the experimental data. The comparison shows generally good agreement between the measured and the calculated data. IntroductionIn a steelmaking process, molten steel carried by a ladle is first fed into a buffer vessel called tundish. From the tundish, it is then fed into a continuous casting mold. Molten steel solidifies gradually in the mold (the primary cooling zone) forming a solidified shell. As the solidified shell is just thick enough to support the molten steel at the mold exit, it is withdrawn through the mold by pinch rolls. It is progressively thicken as it is further cooled with water sprays in the secondary cooling zone. At the end of guide roll zone, completely solidified steel is cut into desirable lengths. Schematic view of a typical continuous casting is shown in Figure 1."

Jan 1, 1999

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

By Stephen C. Tadolini, Raymond A. Mazzoni

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these “simple” devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors’ opinions of course).

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

By Brian T. Hamilton, Richard Piliounis, Cian Murphy

"The Eglinton-Crosstown Light Rail Transit line is a 19-kilometre corridor with a 10-kilometre underground portion currently being constructed by Metrolinx in Toronto through a densely populated urban environment. Tunneling works are being completed through two separate design-bid-build contracts that include consideration for a phased handover to a follow on contractor who will take ownership of the tunnels, including warranties, and will complete the stations and remainder of the system through a PPP delivery model including maintenance of the system for 30 years. Warranty provisions, settlement apportionment, tunnel leakage, potential delays and conflicts between contractors are just some of the risks the team managing tunnel contract integration had to consider when developing the PPP contract. This paper will present an overview of how these risks were assessed and allocated through the contracts and the strategies adopted to minimize risks to Metrolinx while ensuring successful procurement was maintained. INTRODUCTION The Big Move is a 25 year, $50 billion ($-CAD) plan for coordinated and integrated transportation in the Greater Toronto and Hamilton Area (GTHA) in Ontario, Canada. This plan has been initiated by Metrolinx, a division of the provincial government of Ontario, and its vision, goals and objectives are rooted in creating a high quality of life; a thriving, sustainable and protected environment; and a strong, prosperous and competitive economy for the GTHA. The Big Move will triple the length of rapid transit service in the GTHA to 1,725km, significantly increase the percentage of the GTHA population living within two kilometers of rapid transit, reduce commute times to an average of 77 minutes per person per day and decrease greenhouse gas emissions from passenger transportation per person by 29%. Work is currently underway on several projects and more than $16 billion ($-CAD) of the planned investment has already been committed. A key project that forms part of this commitment is the Eglinton Crosstown Light Rail Transit (LRT) Project which is being delivered in the City of Toronto under Metrolinx’s Rapid Transit (RT) Program. This complex and sizeable undertaking has been broken into a number of separate contracts comprising: LRT Vehicles contract; Eglinton West Tunnels Project; Eglinton East Tunnels Project; and a Public-Private-Partnership (PPP) contract to complete the underground stations, at-grade stops, all rail infrastructure and systems and to maintain the entire system for 30 years. The PPP contract, which includes an initial capital portion of approx. $5.1 billion ($-CAD), has recently been awarded to Crosslinx Transit Solutions, a Special Purpose Vehicle (SPV) consortium comprised of SNC Lavalin, Aecon, Dragados and EllisDon."

Jan 1, 2016

By John G. Banker

Titanium/steel clad has been selected as the material of construction for six pressure acid leaching autoclaves for nickel production from laterite ores. These six pressure vessels are now in production service in western Australia. Titanium provides reliable corrosion protection in the nickel laterite pressure leaching environment. Clad metal construction offers a significant cost reduction for equipment of this type in comparison to solid titanium. Clad metal construction offers superior durability and reliability in comparison with non-metal or titanium loose-lined equipment. Experiences in titanium clad equipment construction and performance are reviewed. The presentation addresses aspects of design, fabrication, and testing which are necessary to assure reliable equipment. The explosion cladding proces and titanium alloy selection considerations are also discussed.

Jan 1, 2000