Search Documents

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

With the employment of a system of ore pillars to support the hanging wall during the mining operations at the North Mine, it was found that, when the stopes were worked out and the pillars remained intact, the main footwall drives developed an undulating longitudinal section due to the shrinkage of the filling in the worked out stopes.These depressions collected water, which made the footwall drives very wet under foot, and everitually worked its way into the pillar workings and the levels below.Water was also finding its way into the shafts because of the silting-up of the level drainage systems and, as both the shafts are down-cast, this tended to increase the humidity of the air entering the mine.To overcome these troubles it was decided to try a system of siphons as a method of subsidiary drainage.SYSTEM AT PRESENT IN USE.All drainage water is collected as near to its source as possible, run into a sump in an adjacent low lying part of the level, and continuously removed from these sumps by a siphon system.Each level has its own system. Water is collected from the sumps by a 1-in. pipe and delivered to a pipe running the length of the level along the back of the footwall drive. At the shaft the pipe is increased to...

Jan 1, 1938

By D. W. Lawler

Prior to the manufacture of sulphuric acid in metallurgical plants, the SO2 rich gas from the smelter, roaster, or furnace must be cleaned to removed particulates, volatile contaminants, SO3, and water. Cleaning is accomplished by contacting the. gas with cooled weak acid. The system is designed so that all the contaminants, originally in the gas are captured in the weak acid, which then becomes an effluent from the plant. Historically, the entire weak acid effluent stream has been treated for disposal, with no attempt to recycle or recover any part if it. This is becoming increasingly environmentally unacceptable, and operators must consider better methods of treatment and recovery. In this paper, Kvaerner Chemetics discuss a number of options that allow the contaminants to 'be separated from the acid' value. This will result in an acid byproduct that can be sold or used elsewhere, and will minimize the volume of hazardous byproducts that must be discharged.

Jan 1, 1998

By Paul Soros

The Conneaut, Ohio, terminal of the Bessemer & Lake Erie Railroad was the first rail-to-ground-to-water coal terminal on the Great Lakes. Compared to the traditional method of holding coal in railroad cars at the ports for dumping their contents into vessels, it provided for: a. Immediate train turn-around independently of vessel arrivals. b. Winter storage of coal at the port, permitting year round shipment by the mines and year round operation of the railroad.

Jan 1, 1969

By Raj K. Rajamani, Solomon A. Tucker, Michael K. McCarter

"In a study aimed at exploring possible improvements in operating performance at an Open Pit Copper (OPC) mine in the western U.S., the impact of blast energy changes on crushing performance was evaluated. OPC feeds its 3-stage crushing plant in 12-hour-day shifts with skarn ore from three domains: Pit_B (B), Pit_S Low-Grade (SLG) and Pit_S High-Grade (SHG), in the blending ratio 1:1:1 (B/SLG/SHG). Thecrushed product is fed to a 2-stage ball mill circuit. "

Jan 1, 2017

By Markus A. Reuter, Joep Verwoerd, Marc J. A. Pijnenborg, Yongxiang Yang

"Incineration is a proven disposal technology for all waste materials with heat release potentials, and provides high degree of toxic destruction and control for a broad range of hazardous materials. In the Netherlands, all the hazardous wastes are processed at AVR-Chemie located at the Rotterdam harbour, through rotary kiln incinerators. The newly enforced regulations from the European Union with stricter emission levels require a better understanding of the incineration process and improved process control. However, the transport phenomena and combustion processes within the kiln system are very complex and not well understood. In order to get better understanding of the incineration process, research has been carried out to study the fluid flow and combustion behaviour of the incineration system. Computational Fluid-dynamics (CFD) was used to simulate the gas flow and waste combustion process, and temperature measurements of the operating rotary kiln incinerator were conducted to validate the CFD model. This paper will present the latest results from the current research project for simulating gas flow and combustion heat transfer for a wide range of hazardous waste streams.The simulation of the waste incineration process was carried out using a general-purpose CFD code Phoenics. The rotary kiln and the secondary combustion chamber (SCC), with a waste processing capacity of 50,000 ton/y and an energy input of 30 – 40 MW, is translated into a CFD model. The model includes a k-e turbulence model and a global gas-phase combustion model (3-gas or 7-gas combustion model). The 3- gas model (Simple Chemically-Reacting System, SCRS) predicts only the thermal effect of the fuel combustion, and only one global fuel is used, therefore, real chemical species are not taken into account. In the 7-gas combustion model, (an Extended SCRS, ESCRS), different forms of waste fed into the incinerator have been modelled into a mixture of a general hydrocarbon fuel C3H4 and other components such as CO, CO2 and H2O. Thus, all the incoming fuel streams with different compositions and calorific values can be properly converted into separate inlets. The combustion of the waste is assumed to take place only in gas phase in two steps: (1) primary combustion of the main fuel component C3H4 to form CO and H2, (2) secondary combustion of CO and H2O to form CO2 and H2O. The rate of each combustion reaction is assumed to be controlled by turbulent mixing of fuel and oxidant (air or oxygen), i.e. the Eddy-Break-up (EBU) model. The resulted temperature field was validated with temperature measurement data, and the simulated temperature distribution from both 3-gas and 7-gas model have reasonable agreement with the measured data."

Jan 1, 2003

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By Veneta Groudeva

A pyritic ore containing zinc, lead and copper as? the relevant primary sulfide minerals, .as well as gold and silver finely disseminated in the sulfide matrix, was? leached in percolation columns. Each column contained 30 kg of ore crushed to minus 10 mm. Firstly, zinc and copper were efficiently leached by means of chemolithothrophic bacteria? in acidic sulfate bearing medium. Zinc was leached more rapidly than copper but the final extractions of these metals were similar (about 75% in 300 days). A part of the galena was oxidized to the. insoluble lead sulfate during the leaching. The pyr:ite was, however, relatively slightly attacked. The ore was then leached by means of FeC11 - HCl solutions both in the presence and in the absence of bacteria to solubilize the lead. The chemolithotrophic bacteria grew in media containing both chloride and sulfat~ ions and maintained a high ferric to ferrous ion ratio in the percoiating solutions. The chemical leaching was, however, more efficient since ft was possible to carry it out at higher chloride ion concentrations. About 10% of the lead was leached in this way in 90 days. Finally, the ore was leached by thiourea in the presence of a gold-oxidant (oxone) to extract the gold and silver. Over 60% of the gold and over 55% of the silver were extracted from the ore in 150 days, while. the extractions of these precious metals from an untreated ore sample were lower than 25%.

Jan 1, 1991

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

The use of pipeline-c to carry crude'oil and petroleum pro-ducts is a reliable and economic*Way to transport large quantities of oil. The length and size of these pipelines have continued to grow throughout the world as the demand for petroleum has in-creased and as the price of other transportation-methods has risen. At the present time pipelines 'can move a barrel of oil a distance of 100 miles at an average cost of ,80.06 U.S. dollars.The major elements in pipeline design are discussed. Methods of calculating pressure drop and horsepower requirements are pre-sented. These are variations of standard equations.in which the elements of each equation are expressed in terms common to the petroleum industry. Major equipment is discussed., particularlyas it relates to operation and economics.Cost data are presented to aid in preliminary economic ana-lysis. Curves illustrate the cost of oil transportation at flow rates between 10,000 and 500,000 barrels per day and permit the selection of pipe diameter-which will result in minimum operating costs.

Jan 1, 1962

By O. C. Blade

Production of crude petroleum in the Middle East (southwestern Asia) and in South America has increased greatly during recent years and has become a significant factor in the world's production of crude oil. Crude oil from fields in the Middle East increased from 256,164,000 barrels in 1946 to 305,833,000 barrels in 1947 and 417,201,000 barrels in 1948. Production from South American fields increased from 446,417,000 barrels in 1946 to 518,652,000 barrels in 1947 and 574,837,000 barrels in 1948. Crude-oil production from Canadian fields increased from 7,726,876 barrels in 1947 to 12,370,875 barrels in 1948, most of the increase being attributable to two fields, Leduc and Redwater, both represented by analyses in this report. Present indications are that production of crude petroleum from all these regions will continue to increase.

Jan 1, 1950

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the -pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint .of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth .history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By J. Winters, L. Vos, C. Canoo

Committed to a sustainable development of zinc applications, Union Miniere is investigating processes for the minimisation of waste and residues originating from the classic hydrometallurgical zinc process. In that context, Union Miniere has developed a method for the cold inertisation and solidification of goethite, the Graveliet® process. The result is a hard and inert gravel that can be used in the building industry. During the past two years, a pilot plant for the production of Graveliet® has been built and operated. In the present paper, the Graveliet® process and the pilot plant are described after which the properties of the produced gravel are discussed, from both a mechanical and an environmental point-of-view. Graveliet fulfils the criteria for use as a secondary building material. The GravelietJ process is a viable technology to avoid stockpiling of goethite residues and it thus assures the long-term development of the hydrometallurgical zinc process.

Jan 1, 2000

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others.

Jan 1, 1950

By Rufus Flinchum

Two of the most critical concerns a blaster faces today are airblast and flyrock. Airblast, sometimes called noise or overpressure, can cause damage to neighboring structures, especially windows. It also is the cause for many vibration complaints. The human sense of hearing is often more acute to identifying source than the sense of touch. When a blast occurs, the airblast is what identifies the event. The vibration that may be felt is then associated with the airblast. Vibrations of greater magnitude, such as passing trucks or construction work on the house, go unnoticed because their sounds are familiar or expected. Flyrock is the number one killer and cause of damage. Elasting laws provide limits for these two concerns. Failure to comply may result in fines, closing of the operation, and even prison. Airblast and flyrock originate from two distinct areas, the open face and the bench surface. Each of these areas is addressed in the detailed proven procedures that follow, and if used by the blaster in conjunction with his own blasting knowledge, a sound blasting plan can be developed to minimize the occurrence of airblast and flyrock.

Jan 1, 1992

By Martti Hagfors, Jussi Saavalainen

The underwater explosions has been used as a test method for the determination energy content of explosives. The test method is suitable for all kind of explosives; homogeneous, heterogeneous, wa-ter-resistant, no-water resistant, cap sensitive, booster sensitive, explosives with hard confinement, explosives without confinement etc. It is also the only test method by which shock, gas heave and to-tal energy values of the explosives can be measured separately. This feature makes it possible to use the test method to develop the explosives for different purposes; the military high explosives need more shock energy where as the gas heave energy is very important feature for the blasting and sea mine explosives.

Jan 1, 2010

By D Morgan, D Sato, B Lumsden, S Senanayake

Laboratory flotation tests on fresh cyclone overflow samples are a useful tool to troubleshoot and indeed to improve plant performance; however, reproducibility between laboratory flotation test and plant performance is important for interpretation of the laboratory tests and hence their usefulness. Chemical reproducibility can be achieved with the addition of the required reagents; however, reproducing the physics of forces and energy in a 5 L cell compared to a 50 000 L plant cell or a 500 000 L plant cell is not generally studied or discussed. For some tests such as collector evaluation the physics of the flotation process may not be critical, but for some evaluations in the laboratory, it can be important.All flotation plants suffer from losses of valuable <20 µm mineral. Selective mineral aggregation has long been recommended to improve the poor flotation recovery of <20 µm sulfide minerals; however, successfully testing any type of selective sulfide mineral aggregation’s effect on flotation recovery in the laboratory on practical plant samples requires reproducing plant cell physics. The energy input per litre and the forces in a laboratory cell are vastly different to a plant cell. Reproducibility between laboratory and plant tests requires that these differences be minimised. The physics of the laboratory flotation cell is particularly important when fine mineral aggregation tests are carried out.This paper outlines a modified laboratory aggregation and flotation method that closely reproduces plant performance in a laboratory test.CITATION:Sato, D, Lumsden, B, Senanayake, S and Morgan, D, 2014. Development of a laboratory flotation method to test plant mineral aggregation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L. Alagha, L. A. Sanchez-Calderon

The existing methods for recycling lithium-ion batteries present initial hurdles related to the safe handling and preparation of the batteries to avert potential explosions. Submerging batteries in sodium chloride (NaCl) solution has become an acceptable industrial practice. However, the use of NaCl to discharge lithium-ion batteries rusts the batteries’ cases and releases metals which impacts the downstream processes that involve selective recovery of Li. This study aimed to determine the optimal concentrations and pH range of NaCl for the discharge of lithium-ion batteries for the purpose of minimizing the leach of Al, Co, Cu, Fe, Li, and Ni.

Feb 1, 2024