Search Documents

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during '"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term ''productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By P. J. Uggowitzer, K. Steinhoff, A. Wolf

"With the increasing acceptance of the Thixoforging process in the last few years, also the technical and commercial requirements for this forming technology and its components increased. So far, a great deal of work has been done in the development of an efficient process and control design. However, less attention has been paid to the development of new specifically tailored aluminum wrought alloys for this specific manufacturing process. · In this paper a new AlMgSi-alloy (A6082), optimized for the Thixoforging process, is presented. In the first part, the technical potential of the new alloy is specified by its microstructural evolution and flow characteristics in the semi-solid state. In the second part, the mechanical properties of thixoforged components of different conventional AlMgSi-alloys a (e illustrated · and compared to the new alloy.IntroductionSemi-solid metalworking, also known as semi-solid forming, is a hybrid manufacturing method that incorporates elements of both casting and forging. The key to the process relies on the peculiar flow behavior of slurries containing non-dendritic solid, which was first studied at the MIT by Flemings et al. [i], in the early 1970s. It was discovered, that if an alloy is uniformly stirred during freezing, discrete rounded particles of solid are formed rather than the normal dendrites, and the slurry is highly fluid (-5 Pas) up at least 50% solid. In addition, these slurries posses thixotropic flow characteristics: the viscosity is dependent on sheare rate and time. The more vigorously they are stirred, the more fluid they become. However, on standing the viscosity recovers and the material stiffens (-106 Pas).The semi-solid forming process exploits this phenomenon. In a first step, the required non-dentritical- microstructure is obtained by mechanical or electromagnetic stirring during primary solidification of the alloy. The stirred slurry is generally fully solidified as a feedstock billet and - in a second process step - reheated above the solidus temperature into the semi-solid state. In this condition, the thixotropic properties permit the material to be handled by robotic devices and transferred to a die (Thixocasting) or subjected to- a forming process by means of forging (Thixoforging). Owing to the shear stress which acts on the semisolid material during forming operation, the viscosity of the material is reduced attaining so the desired fluid-like flow characteristics."

Jan 1, 2000

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972

By S G. Gatehouse

Extensive gold mining activity û dominantly alluvial û has taken place in the Sofala-Wattle Flat district since the 1850s.This work will have located most, if not all, of the visible sources for the gold in current stream systems.Also, there are many gold bearing elevated Tertiary alluvial terraces in the district which may confuse possible gold signals from primary hard rock sources in the streams.Associated element signatures eg As and other chalcophiles, will discriminate non-alluvial signatures but will not necessarily distinguish non gold bearing mineralisation.Both trace elements and conventional gold analyses will dominantly re-identify known occurrences. Conventional BCL sampling is considered misleading as experience from the Oberon area to the south of Sofala demonstrated that BCL sampling was very sensitive û perhaps too sensitive.All occurrences û major or minor û of gold will be detected (Gatehouse, 1992). To improve on BCL sampling, a small, -120# sample with selective duplication was recommended to screen coarse-grained gold anomalism and a program of sampling covering an area thought to be prospective was enacted.Samples returning anomalous Au were analysed in duplicate and if the results demonstrated reproducibility, indicating fine gold only, the sample site was assigned a high priority.It was found that most of the reproducible samples clustered in one area û Spring Gully. The results of this sampling program led to immediate identification and, ultimately, the successful delineation of the Spring Gully gold deposit near Wattle Flat.

Jan 1, 2004

By Yuanyuan Wang, XUEWEN WANG, Jinzhi Wei, Ligang Wen, Muxin Jia, Zhengyao Li

The abstract discusses the use of disodium carboxymethyl trithiocarbonate (D8) as an effective depressant in the flotation separation of stibnite and pyrite. The study investigates the mechanism behind D8's selective inhibition of pyrite, utilizing techniques like micro-flotation experiments, contact angle measurements, infrared spectroscopy, adsorption capacity analysis, and zeta potential measurements. The findings reveal that D8 physically adsorbs onto both pyrite and stibnite, but its adsorption capacity on pyrite is significantly higher. This adsorption enhances the hydrophilicity of the pyrite surface, hindering the adsorption of the collector and effectively depressing pyrite flotation, while having minimal impact on stibnite floatability.

Mar 14, 2022

By P. Michael

Proponents of geomorphic mine land reclamation have criticized current reclamation practices in the coal fields of steep-sloped Central Appalachia as too narrowly focused on civil engineering principles and neglectful of the functional and aesthetic benefits of reclaiming mine sites in ways that mimic natural landforms and drainage patterns. They observe that current mining and reclamation practices are radically transforming the mountain-and-valley terrain into gigantic flat plateaus and, in doing so, disrupting the beauty and ecology of the natural landscape. Instead of designing and constructing linear or planar surfaces and unvarying slope gradients during the reclamation process, they recommend ?landforming,? i.e. the adoption of curvilinear, compound slope forms that blend well with the surrounding physiography and represent the result of naturally stabilizing geomomorphic processes. The authors feel that the concept of geomorphic mine land reclamation is sound, however, its application to the Central Appalachian coal fields faces significant--albeit not insurmountable--challenges. They include: (1) existing reclamation enforcement regulations that are focused on civil engineering principles and not explicitly supportive of geomorphic methodologies; (2) regulatory agencies? current intent to limit the down-gradient reach of excess spoil fills in order to allay disruption or burial of natural streams; (3) actual or perceived increases in reclamation costs; and (4) the challenge of designing and constructing ?natural? landforms that are mature and stable in an otherwise youthful, erosional landscape.

Jan 1, 2010

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral-property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive-industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN `01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN '01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB were expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2003

By Guy R. B. Elliott

If chemical mining is to work, it is extremely important to watch heat balances. Some reactions with coal give off heat and others absorb heat. The reactions of coal with oxygen or air give off heat, but the reactions of coal with steam or with carbon dioxide absorb heat. By balancing the proportions of the two types of reactions, the energy of the coal can be almost completely recovered and environmental damage is minimized. The chemical reactions are listed in Table 1 in the usual form with subscripts (s) and (g) indicating solid or gaseous materials. In reaction 1, solid corbon, C(s), reacts with gaseous oxygen, O2(g), to produce gaseous carbon dioxide, CO2 (g). H means enthalpy or available heat in the material; F is free energy, and it measures whether the reaction can go at all, and if so, how much.

Jan 9, 1973

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By M. Sukhram

This paper presents a technique to determine the direction of velocity in liquid aluminum (Al) by measuring the temperature distribution within a cylindrical rod while it is inserted into the flow. The heating pattern of the rod is a result of the interaction of the thermal fields of the rod with the liquid Al. This interaction freezes aluminum onto the cylinder in a characteristic pattern and as a result the temperature response within the rod also follows a distinctive heating pattern. Monitoring the temperature within the cylindrical rod as a function of spatial and temporal coordinates, the direction of velocity can be inferred. Experimental research work involving liquid Al was conducted at the University of Toronto using the Revolving Liquid Metal Tank (RLMT). The RLMT is a resistance furnace which can hold up to 50kg of liquid Al. In this RLMT tangential velocities up to 0.35m1s can be generated. Experimental data for different superheat and magnitude of velocity demonstrate that the sensor records different heating patterns under different fluid flow conditions. Using the transient temperature information, the direction of velocity of the molten Al flow field can be detected.

Jan 1, 2011

By N. Pajunen, R. Mäkikoskela

"The current state of environment has been achieved by acting linearly. At the same time, we know that transition towards circular economy cannot be made the same way that we have used to, trusting only a market economy and economic growth. Environmental improvements have been promoted, some progress has been made, but major steps towards sustainability have not been taken. Industry is now facing significant change, from process related environmental thinking to product-based environmental thinking.Engineers make decisions which have lifelong influence and even longer on environment and society. Material engineers in case of saving natural resources and increasing material cycle, have an important role to play in the transition towards sustainability. Best knowledge of minerals and materials is in the material development phase. If we want to increase the cycle of different materials, it is vital to make decisions towards circular economy in early phase of product´s life cycle.The target of this study is to promote circular economy; to increase material efficiency; to save natural resources; and to extend product lifecycles in process industry via product design and material development. In this study we have a new kind of cooperation. We combine two disciplines, engineering science and fine arts. We promote sustainability via breaking out the silos. We bring the cyclic artistic thinking into engineering science and environmental research. The new research combination makes the existing information visible in a new way, and it will change attitudes and ways to act by means other than traditional linear rationality.We have tested the new working method via the industrial case study with the chosen product: the sandwich panel of construction industry. The target of the study was to create something new from the chosen product with artistic thinking. The working method will be presented in this paper."

Jan 1, 2016

By G. W. Kenzy

Recently, in the United States, questions of possible deleterious synergistic health effects of the gaseous and particulate components in the diesel exhaust and mineral and coal dust have been the impetus for extensive research by several agencies. At the present time, diesel engines are tested and approved for use in gassy and non-gassy underground metal and non-metal mines under Parts 31, 32, and 36 of Title30 of the Code of Federal Regulations. Diesel-powered equipment for use in underground coal mines, though not explicitly addressed in the law, is administered under Parts 32 and 36 of Title 30, with Part 36 being applied in the case of equipment working inby the last open crosscut or in the return airways. Operation of diesel equipment in underground mines has the potential for serious health and safety hazards from the gases, vapors, and particulates in the exhaust. Therefore, various countries have rules and regulations for the safe deployment of diesel equipment. The applicable laws and regulations from several countries who have long experience with diesel-powered equipment in their mines are reviewed. Four major areas have been addressed: (1) testing and approval procedures of diesel engines, (2) ambient mine air quality specifications, (3) frequency of sampling and location of samples, and (4) air quality specifications in splits where diesel-powered equipment are operated. The review indicates that most regulations generally consider four possible hazards: (1) toxic components in the engine exhaust, (2) ignition of flammable atmospheres by the engine or electrical equipment, (3) fire hazards presented by the engine fuel oil and by combustible material that might come in contact with the equipment, and (4) mechanical hazards. There is a remarkable similarity in the laws with regard to engine design, testing and approval procedures. However, the aspects with regard to mine air quality and quantity are quite variable-- from a general statement to very specific standards for many different diesel exhaust constituents. However, the laws with regard to synergistic effects of diesel exhaust components and other mine air contaminants are an exception.

Jan 1, 1980

By Francisco M. S. Garrido, Fabiano A. C. M. Passos, Carla N. Barbato, Karoline K. Ferreira, Danielle C. Castro, Adriana A. S. Felix, Luiz C. Bertolino, Fernanda A. N. G. Silva, Karla M. A. Simões

Cancrinite and sodalite are characterized by high capacity of adsorption due to its porous structure. The aim of this work was to use kaolin from Borborema-Seridó/Brazil as a source of aluminium and silicon to hydrothermal synthesis of sodalite and cancrinite and to evaluate the best conditions to the formation of these phases. Therefore, kaolin was heated at 700 and 900 °C for 2 h in order to transform kaolinite in metakaolin. Thereafter, experiments with the calcined kaolin’s were carried out between 150 and 230 °C for 30–270 min on a stainless steel pressure vessel using NaOH, Na2CO3 and H2O. The samples were characterized by X-ray diffraction, nuclear magnetic resonance, scanning electronic microscopy, thermogravimetry, and Zeta potential. The most pure sodalite phase was obtained at 230 °C, with the kaolin/NaOH ratio of 1:1, low concentration of Na2CO3 and smaller time of synthesis (30 min). On the other hand, for the synthesis of cancrinite phase at 230 °C, it was necessary to use kaolin heated at 900 °C, a longer time of synthesis (270 min) and a higher concentration of Na2CO3.

Mar 1, 2017

By Frank J. Markewicz

The expanding: demand for ilmenite for use in the manufacture of titanium pigments, the knowledge that much of this raw material comes from distant points and therefore has to include a heavy freight charge in the price of the delivered product, and the further knowledge that ilmenite occurs both in the crystalline rocks of northern New Jersey and also in some of the Triassic igneous rocks, were considerations which led to a search for ilmenite-bearing sands in southern New Jersey. That this search was successful is now history, and it is the senior author's privilege to state here that most of the credit belongs to his associates who did all of the heavy work of hand-augering for samples, and who made all of the heavy-mineral separations. We all are grateful to members of the Department of Geology at Rutgers and Princeton Universities for the use of equipment which enabled us to evaluate certain samples from our ilmenite exploration program. In addition, we wish to express our appreciation to many companies for their cooperation and for their permission to publish mineral and chemical analyses. We also acknowledge with much appreciation our debt to the geologists and engineers with whom we have had many lively and rewarding discussions relative to the ilmenite deposits.

Jan 1, 1958

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase

Jan 1, 1937

By Kim Fagerlund

A novel apparatus for studying refractory infiltration and dissolution/degradation under a temperature gradient was developed. To supersede conventional isothermal refractory testing, a new temperature gradient technique, based on a crucible equipped with a cooling element, has been developed to provide practical information on the penetration and dissolution of refractory materials under cooled conditions. This technique was adopted and applied to several refractory-slag systems. Commercially available magnesia chrome refractory bricks against a copper-containing calcium ferrite type of slag were tested and compared using both a conventional crucible test and the new temperature gradient method. The experiments were conducted at 1300-1420°C under a controlled atmosphere of nitrogen or air. It was noticed that the type of porosity has a significant effect on infiltration of magnesia chrome refractories. Furthemore, the copper-containing calcium ferrite slag caused a severe slag attack and refractory failure in some cases, due to its fluidity and corrosive nature.

Jan 1, 2002

By A. R. Byers

"This paper describes the distribution, occurrence, and paragenesis of known sulphide deposits within an area bounded by longitudes 102°00' to 106°00' west and latitudes 54 ° 301 to 57 °00 1 north. The Precambrian bed-rock which outcrops over all but the southern fringe of the area con- . sists of regional metamorphic assemblages ranging from low grade or green schist facies to high grade or amphibolite-granulite facies. The areas . of low-grade metamorphism correspond to 'islands' of volcanic rocks which are surrounded by highgrade paragneisses and migmatites. Intrusive rocks range in composition from ultrabasic to granitic and may be divided into syntectonic and posttectonic sequences. The average composition of the former is granodiorite and of the latter quartz diorite.The massive sulphide deposits fall naturally on basis of mineral content into the following divisions: ( 1) pyrrhotite and / or pyrite, (2) sphalerite and/ or chalcopyrite plus iron sulphides, (3) sphalerite and galena, ( 4) sulphide-bearing pegmatite, and (5) nickeliferous pyrrhotite and / or chalcopyrite. The deposits of iron sulphides are ubiquitous. Ratio of pyrrhotite to pyrite is fairly constant for individual deposits, but their areal distribution appears to be independent of the nature of the enclosing rock and grade of regional metamorphism. All deposits containing ore-grade quantities of base metals have been concentrated at favourable structural locations. Copper-zinc and lead-zinc deposits appear to be associated with syntectonic granodiorite with the lead-zinc concentrations confined to calc-silicate gneisses. Copper-nickel deposits show a close relationship to post-tectonic gabbros and pyroxenites. The paragenesis is more or less the same for the majority of deposits, with iron sulphides and sphalerite being introduced early and followed by chalcopyrite and galena. Some vertical and / or horizontal zoning is apparent in a few deposits. Temperatures of formation and origin of the deposits are briefly discussed."

Jan 1, 1960