Search Documents

By Robert G. Benson, David M. Jones

The San Luis deposit of Costilla County, Colorado contains 11,021,000 tonnes (12,149,000 tons) of ore at 1.4 g/t (0.040 oz/st) gold in two mineable zones. Gold mineralization is associated with silicification and quartz-sericite-pyrite alteration localized in breccias along a low-angle "detachment" fault zone in Precambrian gneiss. Gangue minerals include chlorite, specularite, chalcopyrite, molybdenite, and fluorite. Mineralization is mid-Tertiary in age and may have an indirect genetic relation to the emplacement of felsic intrusions. Portions of the ore body are unconformably overlain by sedimentary rocks of the Tertiary Santa Fe Formation. The deposit formed during the early stages of extensional tectonism along the eastern edge of the present day Rio Grande rift.

Jan 1, 1990

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By A Cranley, A Giblett, S Thacker

The Newmont Tanami Operations are located in the Northern Territory, approximately 550 km north-west of Alice Springs. The Granites process plant commenced operations in 1986 as a 300?000 t/a ball mill / carbon-in-leach (CIL) plant and has undergone numerous expansions between that time and the current day, with project-to-date gold production exceeding 6.5 Moz. Annual plant throughput has exceeded 2.8 Mt/a while processing a blend of open pit material and ore from the Callie Deeps underground mine, with annual gold production exceeding 400 koz. In 2013 the operation processed 1.8 Mt of underground ore for the production of 323 koz of gold.This paper reviews the operation and expansion of The Granites process plant since the mid to late 1980s with particular focus on the gravity gold recovery circuit. The Tanami ores contain significant levels of free gold, and gravity recovery has long been an integral component of the metal recovery process at the Granites plant. The results of ten years of gravity circuit performance analysis and optimisation are presented.CITATION:Giblett, A, Cranley, A and Thacker, S, 2014. Three decades of gold production at the Newmont Tanami operations, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 209–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R. Pérez, James A. Finch, F. Tavera, Cesar O. Gomez

"Gas holdup is a variable which affects the operation of flotation columns. On one hand, gas holdup is a function of bubble size (a function of sparger type, frother characteristics and concentration, and air flowrate), tailings flowrate, solids content, and mixing patterns in the collection zone. On the other, gas holdup defines flotation kinetics and carrying capacity. Therefore, gas holdup is a useful variable to control and diagnose the operation of a flotation column, but the lack of a reliable sensor for on-line gas holdup monitoring has prevented its use in industry.This work describes the principle and the practical difficulties associated with the development of a gas holdup sensor based on the measurement of the electrical conductivity of dispersions. Two different approaches have been devised. These approaches will be described and test results presented of prototypes in laboratory and industrial columns.Background.Several years ago, a research program was initiated at McGill to use electrical conductivity as the basis for developing sensors for process measurements in mineral processing. Electrical conductivity is an intensive property which is a function of the concentration of the different phases present in a dispersion. The initial focus was on the detection of the interface between two dispersions with different characteristics (i.e., that between the collection and froth zones in flotation columns or that between clear water and sedimented solids in thickeners). The technique works in this case by searching for the location at which a sudden change in specific conductivity occurs, as a consequence of different gas holdup or solids content, and absolute values of the specific conductivity of the dispersions involved are not necessary1,2."

Jan 1, 1995

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011 Managing Heat Exposure Control?. The cost implications ?Controlling the environment ?Ventilation already a major expenses/energy user ?Large Canadian mines are currently delivering massive volumes of air 15-20 tons of air/ton ore ?Large investments in ventilation upgrades, mechanical cooling

May 1, 2010

In conjunction with steady increases in production levels, long-wall operators have applied greater quantities of ventilating air to control respirable dust and methane gas. As a result, air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high-velocities, especially during shield advance as dust falls from the shield canopy directly into theair stream. Laboratory tests to simulate dust liberation by shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH in a wind tunnel designed to study dust entrainment in high-velocity airstreams. Dust was introduced into the tunnel to determine dust concentration as it relates to entrainment, dilution, air velocity, and particle adhesion. Airborne dust samples were obtained by iso-kinetic sampling using BGI cyclones to quantify respirable dust concentration at the various air velocities. Laboratory tests were con-ducted at velocities ranging from 2.0 to 10.1 m/s (400 to 2000 fpm),and significant differences in airborne respirable dust levels were measured. This research is being conducted to provide fundamental information on the entrainment characteristics of respirable dust at high air velocities, which will subsequently lead to solutions for shield dust control. A discussion of the test procedures and results are presented.

Jan 1, 2004

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1985

By C. E. Taylor, L. V. Fegan

With on-stream electrical-resistance measurement as a basis, Bethlehem Steel developed a system for the completely automatic control of moisture in the feed to pelletizing. This system was later successfully adapted to the sintering process, with automatic control of moisture serving to maintain the air permeability required for effective burnthrough. Control of moisture content is an important factor in the agglomeration processes by which iron ores are converted into either pellets or sinter for use in blast furnace burdens. In both pelletizing and sintering the iron ore feed must be mixed with the proper amount of water so that capillary attraction and surface tension forces can be utilized to cause the ore particles to coalesce and form larger agglomerates. The success or failure of the entire pelletizing or sintering process depends on maintaining the proper moisture. Therefore, continuous automatic control of moisture is one of the conditions for the automation and optimum use of both pelletizing and sintering processes. In pelletizing, variation in moisture can cause ball size to change and is a common cause of cycling which results in a fluctuating feed to induration. Excessive moisture can cause lumps to form at the cutter bar and contributes to the formation of buildup on the green pellet screens. Green pellets with excess moisture deform and reduce bed permeability. In sintering, accurate control of moisture is also important because moisture must be within the limits that give the bed the required permeability for good burnthrough. In response to these problems, a moisture meter, based on the principle of electrical resistance measurement, was developed. This moisture meter has been a key factor in the development of systems for providing uniform feed of concentrates in most of Bethlehem's pelletizing and sintering plants. The automatic moisture control system for pelletizing was successfully plant-tested and resulted in the following: (1) Control of moisture in the green pellets to +0.2%. (2) Up to 50% reduction of bentonite consumption. (3) Control of unscreened green pellets so that 85% of the furnace product at Cornwall was within the size range of -5/8 +3/8 in. (4) Improved quality of product with a tumble test of 94 and a "Q" index of 90 as the result of feeding a consistently uniform feed to a shaft furnace. In sintering, where sinter-mix temperature change and variable feed could cause errors in moisture measurement, the system was designed to maintain the correct moisture under virtually all plant operating conditions. It was successfully plant-tested and is now in use in most of Bethlehem's sintering plants. The system achieves: (1) Control of moisture within the desired limits for optimum production. (2) Continuous measurement and control of moisture even with intermittent feeding of mix, so that attention by the operator is seldom required. The two automatic control systems provide smoother startup, minimize upsets and contribute to the consistent control of process variables in pelletizing and sintering. MOISTURE-CONTROL SYSTEM FOR PELLETIZING Fig. 1 shows the general arrangement of the system for automatic control of moisture in pelletizing.1 In this system a bin level controller, using a single probe which regulates filter speed, maintains a uniform low concentrate level in the bin.' The moisture meter, comprised of an analyzer and control components, continuously measures the moisture in the bed and adds water to adjust to the desired level. The meter is placed in an open-loop (feed-forward) control, i.e., water addition occurs downstream from the probes. Filter vacuum must be set so as to produce a filtercake moisture which is below the optimum for pelletizing. Bentonite is added after the

Jan 1, 1969

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

To improve mining safety and efficiency by providing a practical way of detecting faults and channel sands that disturb coal seams. Approach A seismic system using a shallow blasthole has been developed and tested. How It Works A small shock is caused in a shallow hole, sending seismic waves through the ground. These waves are reflected from the top of the coal seam, acid are detected by a line of geophones on the earth's surface. Dampening of the seismic signals by channel sands and other discontinuities in the seam is detected and recorded. See Figure 1. The seismic shock wave can be produced by exploding small charges, dropping a weight, firing a gas gun, or actuating a vibrator. Depending on the soil cover, the shock is usually generated in shallow vertical holes about 10 feet deep. Hole depth depends on the soil mantle thickness because it is preferable that the seismic shock originate below that layer.

Jan 1, 1976

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By G. Robson

"From monitoring gas levels and air quality in coal mines to protection from collisions for large vehicles at mine sites, SICK offers a wide range of sensors and systems to improve safety and to monitor potentially dangerous situations. SICK offers solutions for the analysis and monitoring of underground coal mining atmospheres. These systems supply the coal mine operator valuable safety and ventilation information, as well as data which identify and monitors atmospheres of those production areas within the mine which may or may not be worked, such as Goafs and sealed areas. Underground coal mines contain dangerous gases, which must be monitored and controlled in order to allow productive mining operations to take place and to minimize the risk of explosion. Underground mines are a potentially dangerous place for mine workers. These are the main reasons for using Tube bundle systems SICK has had great success in selling these systems into the Australian and New Zealand Markets and this is helped by the strong drive for mine safety from both the Mine Owners and the Regulatory bodies charged with the responsibility of ensuring Mine Regulations are met. The Australian mining industry uses Tube Bundle Systems at almost all underground sites, even after mining has ceases and the mine is placed in care and maintenance. Sick has been working in international markets for some time now but has had limited success in selling Tube bundle Systems to these markets. However in recent times there has been raised interest in Tube Bundle from China, India and Turkey as these countries strive to improve mine productivity and lessen the risk of explosion or Spontaneous Combustion. Our lack of penetration into International Coal markets has been very much based on the perceived cost of the system, not the benefits to safety and productivity. Unless a mine has had an event such as spon com or a Methane explosion they rarely consider the very low level measurement capability (20 PPM CO & 100 PPM CH4) or the long term trending benefits of the Tube Bundle system. It is only after a catastrophic event the System is considered. Real Time or electrochemical Sensors are commonly used to monitor the Mine Atmosphere, the real problems of methane build up or potential Spon Com in Goafs and sealed areas cannot be monitored using Real Time Sensors as the electrochemical cell deteriorates after approx. 12 months and in sealed areas these cells cannot be maintained or replaced. Whilst the Technique of Tube Bundle Systems is quite old SICK have spent many years redesigning the Tube Bundle System into a cost effective and real value for money product. The system uses state of the art sampling and highly accurate Infra-Red wide Spectrum Analysers."

Jan 1, 2016

By Rajive Ganguli

There are several elements of online pedagogy and information technology that are being used in the University of Alaska Fairbanks’(UAF) course “ES 201: Computer Techniques,” to enhance classroom teaching. The use of information technology in this class grew from a desire to make lecture notes available to students. This has grown to include a sophisticated, online delivery software package. It provides chat rooms, discussion groups, and online testing and grading. Online delivery aside, the class uses the telnet, e-mail and C++/FOR-TRAN compiler facilities of the university server during class to enhance learning. During class, for example, the students read the lecture notes on the Web browser, telnet to their university Unix accounts, check their e-mail and download programs (to be covered in class) sent by me, and then compile, run and modify the programs. The class, therefore, requires students to be active most of the time. This ensures their full attention and better learning due to the hands-on experience (Fig. 1).

Jan 1, 2000

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By R. W. Baldwin

As used in geophysical exploration, the term overvoltage applies to secondary voltages set up by a current into the earth which decay when the current is interrupted. These secondary effects may be measured by pick-up electrodes. The term induced polarization has often been employed to describe this same phenomenon. In its own operations Newmont Exploration Ltd. commonly uses the word pulse. The basis of this method in prospecting is that metallic particles, sulfides in particular, give a high response, whereas barren rock, with certain exceptions, gives a low response. Overvoltage has been tried in searching for many types of mineral occurrence but has been most successful in outlining the widespread disseminated mineralization associated with porphyry coppers. History:' Newmont Mining Corp. has been interested in overvoltage since 1946, when Radio Frequency Laboratories of Boonton, N. J.. drew the company's attention to phenomena observed in the laboratory. At the instigation of A. A. Brant further model studies were undertaken, and the first tests were performed in 1947. Tests at San Manuel, Ariz., in 1948 were very encouraging, clearly demonstrating that the method could be used to distinguish scattered sulfides at depth. H. 0. Seigel followed up the San Manuel work with a study to determine the phenomena involved.'

Jan 1, 1960

By Bigu J, Grenier M. G, Knight G

Particulate control is a major concern in underground mining and the subject of continuing research world wide. In Canada the federal government's Mining Research Laboratory at EIIiot Lake, Ontario, has been using two aerosol counters to aid its investigations. Specific studies with the units include: a) evaluating total and elemental size efficiencies of dust filtration units: b) characterizing the dust particulate cloud from different mining operations: and c) determining dust transportation characteristics.

Jan 1, 1988

By Karl Berger, Roman Schneeweis, Dietrich Mathweis

With increasing demands from customers to provide flat strip with tighter tolerances on material properties, particularly flatness of e.g. martensitic steel grades (M1500), it has become necessary to develop strategies to improve flatness without influencing the tensile properties for such hard steel grades. Usual skin pass mills are not capable to apply sufficient tension and roll force for these kinds of material to improve the flatness. Therefore, alternatives had to be searched for. This paper describes skin pass - / temper – rolling methods from the classical one to new alternatives in order to satisfy the demanding market of higher material properties and idle running mills in rolling plants.

Oct 1, 2019

By Paulo C. Fernández A, Sergio Matamala V, Claudio C. Gajardo, Christian A. Rees P

In fragmentation processes in open-pit mining, it has been observed that there are many opportunities for improvement if greater control of ore displacement in blasting is achieved, reducing the percentage of mixing between ore and waste material (dilution) through the integration of new technologies that allow its quantification and optimization of extraction polygons. This work investigates the relevance of the initiation sequence and direction of displacement in blasting in relation to ore dilution and the potential benefits of process optimization. A three-dimensional modeling tool was used to evaluate movement control optimizing the extraction zone based on the maximization of ore recovery. The study was made by iterating different scenarios, by varying only the initiation sequence and inter-hole delays. To validate the displacement simulation, a total of 10 blasts were carried out for calibration, obtaining a level of agreement between the simulation surface and the actual topographic survey of 80% or higher. The analysis included horizontal and vertical displacement, quantification of swell and dilution within extraction polygons for different scenarios, and informed decision-making based on ore control. The results clearly indicate that by modifying the blast initiation sequence, greater control over dilution in ore/waste transition areas is achieved, thus optimizing the recovery of the planned material and maximizing the ore grade. The use of this type of simulation tools allows for the generation of extraction strategies based on the value of the polygon, unnecessary displacements in the free face, optimal loading fronts, etc., maximizing the recovery of ore and stockpile material, complying with the planned tonnage and ore grade for each extraction polygon, delivering added value to the chain and emphasizing the importance of adding new technologies to the mining industry that allow for the optimization of processes to maximize profits.

Jan 26, 2026