Search Documents

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

By Clarence O. Babcock

In this report, the Bureau of Mines presents a method for reducing the complexity of designing room-and-pillar mining systems by treating them as anisotropic soft inclusions in the surrounding ore or host rock. Theoretical models were derived for the calculation of the effective Young's moduli for these systems. The predicted behavior of the plate-type elements used in these models agreed well with test results from 21 plates each with 49 holes spaced on a 7 X 7 Cartesian grid. The plates behaved as anisotropic solids, the effective Young's moduli of which could be predicted from the scaled hole size and spacing. Actual hole shape was insignificant. The effective Young's moduli for simple mining systems are calculated in sample problems. This approach should provide information about field stress in the mining region and the stress distribution in the surrounding ore or host rock when the actual mining configuration is replaced by an anisotropic inclusion in a finite element analysis. The field stress within the inclusion can then be applied to the actual opening shape to determine the stress distribution within the mining region.

Jan 1, 1970

By A. S. Appleton, M. B. Bever

The stored and expended energies of an Au-Ag alloy deformed in torsion were investigated as functions of strain, strain rate, and temperature. At room temperature, the stored energy, measured by tin solution calorimetry, increased linearly up to an intermediate strain, above which it was nearly constant; at 78 °K the relation was linear up to fracture. Approximate values of the energy stored at 4 OK indicate a rapid increase below 78 OK. The energy stored by specimens deformed successively at 4o and 78oK changed slowly with increasing second strain from the curve for energy stored at 4 OK (measured after annealing at 78oK) to that for deformation at 78°K. The ratios of the stored to the expended energy at room temperature and 78 oK were unusually large. The additional amount of energy stored at the lower temperature is attributed mainly to an increase in the number and energy of dislocations. The stored energy as a function of strain rate at 4oK (measured after annealing at 78oK) increased to a sharp maximum over a narrow range of strain rates, whereas the expended energy changed only slightly. These effects are explained by the generation of point defects resulting from the enforced nonconservative movement of jogs in fast moving screw dislocations. The effect of straining successively at two strain rates at 4oK was also investigated. Stress-strain curves for 4o, 78oK, and room temperature and the results of micro examination of specimens deformed at these temperatures are also reported. THIS investigation is a continuation of a research program primarily concerned with the effects of variables on the energy relations involved in the deformation of metals. The variables investigated in earlier work have included strain, strain rate, temperature of deformation (room temperature and 78oK), and the type of deformation process. Most of this work has been carried out with Au-Ag alloys. In the investigation reported here, the deformation process was torsion, which had not been used previously in the program. The stored and expended energies involved in the deformation process were measured as functions of strain, strain rate and the temperature of deformation in the range 4" to 373" K. The microhardness and microstructure of deformed specimens were also investigated. The relation between stored energy and strain differs for different deformation processes.1,2 In general, the stored energy increases with strain and may attain a nearly constant value at large strains. This value and the rate at which it is reached, however, depend on the process of deformation. This dependence has been attributed, at least in part, to differences in the effective strain rate and rise in temperature of the specimen during deformation. The effects of the temperature of deformation on both the stored energy and the energy expended in the working process have been the subject of only a few investigations.3-6 Values of these quantities at low temperatures are of special interest as they yield information on point defects which, for many metals, is not obtainable at higher temperatures. The effect of the strain rate on the stored and expended energies has received little attention The strain rate has usually been measured only in relative terms, and hence the interpretation of its effect on the stored energy has been mainly comparative.

Jan 1, 1963

By Frank Cappuccitti, James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured.The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2005

By G. E. Erdman

Gouverneur Talc produces a dry mineral filler from the tremolite talc rocks located near Gouverneur, New York. The raw material for this rock powder is a silicate rock and dust is controlled by water sprays whenever it becomes a problem underground. In the milling operation, there are some nine baghouse-type dust collectors which are utilized for the control of dust created in the crushing and grinding process. These collectors have been installed over a period of years since 1947 and are assigned to specific areas where the particle sizing of the dust can be returned to the plant circuit or product involved at the point of collection. It has been found very advantageous to mount most of these collectors on the top of the mill building and packhouses where the return of the dust can be accomplished by a gravity feed. In the years of effort involved in efficient control of dust generated in the plant, many things have been learned in the construction of ducts for control valves. The company has found useful such things as grasshopper legs for interconnecting silos with similar products, the elimination of fiat dust ducts, cleaning cyclones for coarse dust or heavy loadings, refractory linings for cyclones and certain duct areas, and the avoidance of square intersections when diverting or combining ducts. Operating cost records indicate that collectors handling the finest dust have the least expense. Operating costs on high-temperature dusts generally run higher than other types of material collected. Experience further indicates that the multiple cyclone-type collectors can provide a low cost and efficient way of removing hot dusts from process air streams before the introduction of the material into a baghouse. High moisture conditions and cold northern climates have been found to combine and create conditions under which baghouses can not efficiently function as dust collectors. Gouverneur Talc feels that its several dust collection systems have been a considerable maintenance expense but well worth the cost when it came to safeguarding the employees' health and preventing air pollution.

Jan 1, 1974

By A. A. Tytko, T. S. Golosinski

"The paper discusses the accuracy of magnetic inspections of corroded hoist ropes. It quantifies the error of measured LMA (loss of metallic area) caused by presence in the rope of ferromagnetic products of corrosion. The paper concludes that in mining practice this error is not significant. Hoist Rope Corrosion and its AssessmentCorrosion is one of the most common forms of wire rope wear. For ropes working in wet mine shafts, ropes used by the fishing industry and, in general, ropes working in humid and chemically active environments, corrosion wear is usually the prime reason for rope discard. In most mining applications, rope corrosion is accompanied by fatigue cracking of wires, abrasion of external wires, internal nicking and other forms of wear.Quantification of corrosion damage in ropes using standard inspection procedures and examination methods is very difficult. Qualitative comparisons are sometimes used to describe the degree of rope corrosion to compensate for the lack of quantitative measures (SABS 0293, 1996). If available, the results of magnetic examinations of ropes may be of help in assessing their corrosion weakening.Magnetic rope examination requires that the rope first be magnetized. After that, the rope magnetic flux and the leakage flux along the rope are measured. The first is assumed to be directly proportional to rope metallic area (LMA) and its changes are indicative of the rope’s loss of breaking strength (LBS). Existence of the second indicates existence of local faults (LF) in the inspected rope. As the corrosion of rope results in development of corrosion cracks and in loss of rope metallic area, both the LF and the LMA should be used to quantify the level of rope corrosion. More specifically, the changes to the amplitude of the LF signal are considered to provide qualitative information on rope corrosion (Hansel et al., 1990), while those of the LMA signal are believed to provide quantitative information (Geller and Rousseau, 1990; Golosinski, 1996)."

Jan 1, 1999

By Dave Tahija

"Many investigations are being performed with the goal of removing carbon dioxide from the atmosphere and permanently storing it in geologically stable settings. At the same time, carbon dioxide in the form of dissolved carbonate is steadily accumulating in the world's oceans. Both carbon dioxide sequestration and oceanic accumulation are constrained by the aqueous thermodynamics of the carbonate system. These constraints are illustrated using the STABCAL computer model to generate potential-pH and aqueous distribution diagrams of seawater in contact with various pressures of carbon dioxide gas. STABCAL diagrams and titration simulations are also used to model some potentially useful cation-carbonate sequestrationsystems.IntroductionAtmospheric carbon dioxide concentrations have risen dramatically in the past couple of centuries and are rising still, primarily as a result of human activities, especially the burning of fossil fuels. Increased atmospheric carbon dioxide concentrations have been implicated as a main cause of global warming but have other effects as well.Rising levels of atmospheric carbon dioxide result in increased concentrations of dissolved carbonate complexes in water, including the oceans. These dissolved carbonates interact with other dissolved substances, altering overall seawater chemistry, most noticeably causing lowered pH levels.Some of these chemical changes are observed directly, for instance the general drop in oceanic pH, [1], while others can be inferred and predicted using thermodynamic modeling. The chemistry of dissolved carbonate in seawater is not especially intricate, as such chemical systems go, but neither is it simple enough to be worked out on the back of an envelope. Interactions between the several simple carbonate species and all the major dissolved cations in seawater should be considered, as well as the effects of competing anions, especially chloride and sulphate, since they are much more abundant than carbonate in seawater."

Jan 1, 2011

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By G. P. Gladis, R. H. Atkinson

PALLADIUM has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items-at least 100 times as rare as gold. Although both visual and spectrophotometric examination demonstrated that the color of palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400° to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

The small scale alluvial gold mining industry in Papua New Guinea (PNG) is c.irrently the only form of small scale mining carried out in this country. It already contributes significantly to the economy with current production estimated at 2 000-2 500kg per year. Until recently, small scale alluvial gold mining has been confined to simple panning and sluicing of high grade alluvial and colluvial deposits. Traditionally the small scale miner in PNG has only worked gravels with gold grades in excess of 500mg/m3. Grades of this order are required to justify the hard physical labour involved ~n hand operated small scale mining methods. .he introduction of higher throughput technologies such as trommels fed by hydraulic excavators has the effect of altering what constitutes an economically viable deposit. Mechanised techniques allow for the consideration of grades of almost half that level. The potential and opportunities for utilising this type of small scale mechanised mining in PNG are enormous with large areas of ground with gold grades running in excess of 250mg/m3 and often up to 2000mg/m3 throughout the country. An assessment of the current operating economics of this technology in the PNG context is the principal objective of this paper. Small to medium scale mechanised mining can potentially contribute significantly to the PNG economy particularly as it lies within the react-, of many PNG businessmen. Its potential is currently somewhat limited by a general lack of infrastructure and is also constrained by socio-political factors.

Jan 1, 1991

By H. Ries

In the marketing of mineral products, it is always highly desirable for both the producer and the consumer to be able to discuss things in a common language, and this can only be done if there are standard methods for expressing the properties of the raw materials. Having developed such a form of expression, the next step would be the making of specifications, which may serve as a basis for selecting raw materials. Considering the large number of non-metallic minerals that are used, there are not a few for which there are no standard laboratory tests to be used in determining their properties, or even standard specifications on which grades or market price may be based. Indeed in many cases the consumer simply requests the producer to submit samples, and rejects or accepts them without any explanation. Could the producer know in advance just what the consumer needed, time and money might often be saved. It appears to the writer that it is of the highest importance to devise standard laboratory tests wherever possible, as this enables the consumer to state definitely what he needs, and is of great assistance to the producer. It should also work to reduce misunderstandings and disputes. In the case of sands, we find that they show a wide variation in their character, ranging from those that are so coarse as to be of gravelly nature to those that are so fine that they might be classed as silt; and from very clayey ones to those that are practically free from clay. For this wide range of sands, we have a corresponding variety of uses, which are based mainly on the physical properties of the sand, although these are not always very definitely stated. The chemical composition need rarely be considered, if the sand is of siliceous nature. To determine and express these properties there should be standard tests, which are to be followed in all cases where the material is tested in the laboratory. The use of sands for foundry work (making molds or cores) is old, and it has been recognized for some time that the important properties to be

Jan 1, 1926

By Wilton Johnson

The development and use of minerals and mineral fuels are essential to national security and to the maintenance of an expanding economy. As a Nation, we often met these needs but failed to recognize and assess the impact that mining and mineral processing activities have on other natural resources. Currently, the growing demand for energy and minerals is accompanied by an increasing awareness that the provision of these resources must not conflict with society's demand for a clean and habit-able environment. Although present mining and mineral processing activities incorporate, or have under development, technology capable of minimizing environ-mental impacts on land, air, and water, many older operations, particularly in the first half of this century, lacked the technological, social, and environmental insights that exist today. Consequently, a substantial backlog of damaging and potentially damaging conditions remains from such problems as mine subsidence, acid water generation, burning and nonburning waste banks, abandoned surface-mined lands, abandoned underground mine fires, and abandoned mine shafts and oil and gas wells.

Jan 1, 1979

By AIME AIME

A MODERN copper reduction works has both a genera1 chemical laboratory for control work and a research laboratory for the study of improvement of present processes and better working-up of by-products. The division of work in the general laboratory would naturally differ in different plants. The following statement to the writer from a chemist in one of the works will give a good idea of the type. of work in the general laboratory :

Jan 1, 1929

By Blamey Stevens

My previous paper is entitled, The Laws of Igneous Ernanation Pressure. The present paper lays no claim to the exactitude and completeness of a law, since it is of a provisional nature and may be disregarded when experiments have established a basis for more exact reasoning. The general physical states in which aqueous emanations may occur are first considered. The possible physical couditions under which the mineral elements may occur in emanations are then discussed, and a classification of deposits, dependent on emanation, is proposed. A system of scientific experimental investigation is outlined, and it is shown that the physical and chemical properties of emanation may be exactly determined thereby. The investigation is urged as feasible and simple, and not necessarily requiring large and costly apparatus. It is the only step necessary to make possible the formulation of a complete set of laws of igneous emanation. Process of Emanation. In a rising column, magma ranges in temperature from 900° to 1,200°C. Exhalation must begin at some fairly great depth. What this depth may be we can only surmise, since no experimental evidence is available. Exhalation, however, continues as the magma flows upward, until at another level the occluded gases have all escaped. This depth is probably upward of 5,000 ft. (See Fig. 1.) All exhalations must come from between these two levels. As the whole emanation is the sum of the exhalations and residues, the residues must come from below the uppermost level. They will be most abundant when coming from those parts of the intrusion which have solidified below the lower level.

Jan 1, 1913

By J. G. Richardson, K. H. Coats

During the initial growth of a gas bubble in an aquifer storage reservoir the injected gas tends to override the water. The resulting low displacement efficiency and high rate of gas travel down-structure make it difficult to maintain water-free production. This paper illustrates the use of two-dimensional, two-phase calculations to simulate this gas-water displacement. Calculations were performed for a stratified aquifer and for several homogeneous sands differing in permeability, porosity and thickness. Results are discussed and compared with performance predictions obtained from the simpler Buckley-Leuerett and Dietz formulas. This comparison indicates the necessity for the two-dimensional calculations in realistically simulating the gravity override of the water by injected gas. INTRODUCTION In recent years natural gas has been stored near markets in aquifers where insufficient storage capacity is available in depleted fields. Operators of these aquifer storage reservoirs have encountered technical problems relating to the gas-water displacement accompanying initial growth of the gas bubble. Injected gas tends to override the water, with a resultant low displacement efficiency and high rate of gas travel down-structure toward spill points. Low displacement efficiency makes if difficult to sustain water-free gas production. Sometimes the fingering of gas down-structure may be so pronounced that the injection rate must be severely curtailed, which excessively lengthens the time required for bubble growth. This paper is concerned with estimating — for given aquifer characteristics and fluid properties — the displacement efficiency, rate of gas movement down-structure and rate of gravity drainage of water behind the gas front. Several published articles relate to simulative capability necessary to handle this problem. The Dietz formula1 and Buckley-Leverett2 method have some applicability to the problem; Woods and comer3 reported one-dimensional, radial calculations which accounted for the two-phase flow of gas and water. Most recent research directed toward understanding aquifer behavior in relation to gas storage has concentrated on single-phase flow in aquifer.4 Douglas, Peaceman and Rachford5 presented a method for calculating multidimensional two-phase flow in reservoirs; their method has been applied in work reported by Nielsen and Tek,6 Blair and peaceman7 and Goddin.8 Refs. 5 and 7 show comparisons between experimental data and calculations similar to those employed here. One purpose of this paper is to illustrate the use of two-dimensional, two-phase flow calculations in simulating the difficult problem of water displacement by gas in a vertical cross-section. The pronounced fluid density and viscosity differences combine with the disparity in horizontal and vertical dimensions of the cross-section to pose one of the more difficult problems in reservoir simulation. The calculations described account for capillary and gravity forces, relative permeability and reservoir heterogeneity. An example reservoir is described and calculated results are presented for a variety of injection rates and values of permeability, reservoir thickness and dip angle. A second purpose is to compare the two-dimensional calculations with results obtained from the Buckley-Leverett and Dietz formulas. For this reason most calculations were performed for a simplified example reservoir to which the latter techniques might reasonably be applied. However, the computer program employed applies equally well to cases involving arbitrary spatial variations of permeability, porosity, reservoir thickness and dip angle.

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By Dean C. Holt

This work was done to appraise the potential of titanium minerals in known titanium- bearing placer deposits and potential titanium- bearing placer areas in western Montana . Reconnaissance studies were made of more than 225 stream areas . Churn drilling and other placer exploration techniques were used in sampling eight deposits . The sampling results indicate that areas containing more than 10 pounds of ilmenite and other titanium- bearing black - sand minerals per cubic yard occur in the Bitterroot , Upper Clark Fork , and Jefferson River drainages . The chief source for the constituents of the black sands appears to be the Idaho batholith , and the highest black - sand concentrations are generally found near the source . Sample testing methods include gravity and magnetic separation and visual microscopic as well as chemical and radiometric analyses on deposits sampled in detail .

Jan 1, 1964

By Jackson R. Pressley, M L. Hopkins, R E. Danell, N T. Moxon, Andrew Bowman

Efficient and cost effective blasting is achieved by closely matching the explosive energy to the strength of the material in which it is being used. Although there are many empirical relationships wich approximate this situation complete the blast optimization can only be achieved by quantitatively assessing explosive/rock interactions and explosive performance. The performance of an explosive is essentially governed by its velocity of detonation or the rate at which the detonation wave travels through the explosive column.

Jan 1, 1991