Search Documents

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

By Anthony D. Hammond

The use of geographic information systems (GIS) as a tool to analyze and display data is gathering momentum in the mining industry. Of particular interest is the capability of GIS to link spatial features and tabular data. The application of GIS in underground mining discussed here concentrates on four technical areas. They are land ownership and mineral claims, exploration management, production and mine safety.

Jan 1, 2002

By J. W. Pugh, J. D. Nisbet

THIS study of the ternary has been made as one phase of a metallurgical investigation which began nearly four years ago in the General Electric Company's Research Laboratory in Schenectady, N. Y. The objective of this program is the discovery of new metallurgical information which will lead to the development of better high-temperature materials. Combinations of the four pure base elements—iron, chromium, nickel, and cobalt—are being studied at the present time. It is essential in an investigation such as this to know as much as possible about the constitutional diagrams involved. The study of the iron-chromium-nickel system has been made to this end. Preliminary Explanation of Experimental Procedure: In all, fifty-five alloys at steps of 10 at. pct were made for the investigation of this ternary. Several ternary alloys in the chromium rich corner had to be omitted because their extreme brittleness made testing impractical. All alloys were vacuum melted with hydrogen reduction and centrifugally cast. The apparatus and technique of this process has been described in detail by Nisbet.1,2 The purity of the alloys prepared in this way is considered to be quite good. Impurities are listed as follows: Pct Carbon.............................0.02 Oxygen................................0.02 Nitrogen.........................0.005 Magnesium..................0.03-0.05 Sulphur...........................trace Hydrogen....................trace Phosphorous..................trace Silicon........................ trace After casting, all samples were given a homo-genization treatment which consisted of holding them for 15 hr at 1150°C (2100°F) and water quenching. Testing was begun with the samples in this condition. The tests employed in the study of this system were (1) dilatometer, (2) hardness versus aging temperature, (3) tensile strength and elongation versus temperature, (4) microstructure analysis, and (5) electrical resistance versus temperature. Dilatometer tests were made at the rather rapid heating rate of 1093°C (2000°F) in one hour on a Bristol-Rockwell type instrument. Hardness data were taken on specimens cooled from 204", 427", 649°, 760°, 871°, 982°, and 1093°C under conditions which are thought sufficient to bring the specimens to equilibrium in all but the cases of the very sluggish transformations. Electrical resistance data for several specimens were taken for both heating and cooling conditions in a vacuum furnace especially designed for this work by D. W. Bainbridge, formerly of this laboratory. Provisions were made for heating and cooling standard specimens at a constant rate, while autographic records of resistance and temperature were made simultaneously. Micrographs of all the alloys were made in the quenched condition. Some question may exist as to how such physical values as hardness, tensile strength, and elongation were interpreted to indicate a change in phase. Original data were recorded on physical property versus temperature graphs, each of which was made from the data of a single alloy (fig. la). From these, another series of graphs were plotted with the physical property as a function of composition for constant temperatures (fig. 1b). Sharp deviations in the slope of these composition versus hardness curves often indicate a change in phase. The example of fig. 1 will serve to describe this experimental technique. The plotting of a single point from graph "a" to graph "b," and finally to the phase diagram "c," is illustrated. The location of the point on graph "b" is indicated as point (1). If all the alloys of the A-B binary system were solid solutions at temperature X, the hardness in this curve would be expected to rise at a fairly even rate as A is diluted with B to a maximum at some intermediate value between A and B, as

Jan 1, 1951

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

East Nelson and Marlborough, in the northeast of the South Island, contain a wide variety of metallic minerals, including gold, silver, copper, chromite, antimony and scheelite, but no sustained metallic mining industry has evolved. Gold was the most sought-after mineral during the first century of European settlement and numerous discoveries were made but these failed to live up to expectations. While traces of gold are widespread in east Nelson, including in quartz veins in Nelson City, no payable deposits were found. In Marlborough the probability of a gold discovery had initially seemed remote but all this changed with the finding of rich deposits in the bed of the Wakamarina River in 1864, which provided a much-needed boost to the provincial economy. However, the decline of gold mining in Marlborough began virtually as soon as it had commenced. Extensive floods in 1865 hastened the exodus of miners to the profitable new fields of the West Coast.

Jan 1, 1993

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G. L. Oldright

[This paper is the fifth 4/ of a series of publications on smelting in the load blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various tines with the main factors governing the operation of the blast furnace, and metallurgical losses.]

Jan 1, 1929

By E. G. Deane

THE CHAIRMAN (P. G. BECKETT, Globe, Ariz.).-The mining of large orebodies has in the last few years been such a big factor in the copper output of this State, and, in fact, of the whole country, I feel that we should have some valuable discussion this evening on the various mining methods described in the papers which are to be read; and I hope you will start a discussion on Mr. Deane's paper. J. A. EDE, La Salle, Ill.-I would like to ask whether, the timbers being left in, they have any fires owing to that fact? E. G. DEANE.-No, we do not. The timbers in the mat seem to lose life. I cannot tell you exactly what change takes place, but they do not burn readily. There is undoubtedly a chemical change in them-a change that makes them lose all strength. I , spoke of the strength of the sills. When we first started, we put in 4 by 8 sills, but those sills had no more strength in 6 months than a 2-in. plank would have. .J. P. HODGSON, Bisbee, Ariz.- I would like to ask Mr. Deane if the central supply raise in the- center of the block has been satisfactory; and also whether in extracting the ore they put small raises up so that wheelbarrows are not used in the stope?

Jan 12, 1916

By H Kim, M J. Sun

In order to reduce carbon emissions from the steelmaking process and achieve carbon neutrality, global steel companies are establishing their own medium to long-term strategies and implementation plans using competitive technological advantages held by each steel company. At this point, Hyundai Steel has formulated a product-oriented carbon-neutral strategy based on innovative processing that makes use of Hyundai Steel’s own strength. Based on our experience in electric arc furnace product manufacturing and blast furnace operation in an integrated steel mill, Hyundai Steel is driving the Hy3 (Hy-cube) project, which involves a unique hybrid production system utilising hydrogen and hydrogen-based renewable energy sources. This initiative aims to achieve carbon-neutral production and eventually specialise in producing premium carbon-neutral automotive parts. The project has originality in that it involves not only designing processes using electric furnaces to produce premium steel products such as car body panels and electrical steel sheets, but also aims to reduce carbon emissions from the process, developing carbon-neutral products based on market demand. To assess the feasibility of the Hy3 project, Hyundai Steel conducted two pilot productions. The first pilot was producing a prototype of lower-arm part using electric arc furnace with three different kinds of raw materials: molten iron, HBI (hot briquetted iron), and scrap. Successful performance evaluation of auto parts with 1 GPa strength was achieved. The second pilot has been focused on tire cord steel, with the first-phase tests yielding a 33 per cent reduction in carbon footprint (CFP). Using the advantages of operating experience in electric arc furnace, Hyundai Steel is preparing for test operations producing various automotive parts using an electric arc furnace (EAF) to advance the Hy3 concept. From a medium to long-term technological development perspective, Hyundai Steel’s blueprint includes producing high-end carbon-neutral steel products using hydrogen-reduced iron as raw material.

Jun 19, 2024

By M. E. Wadsworth, J. R. Lewis, J. M. Quets

Samples of snythetic magnetite were reduced in hydrogen at various partial pressures and temperatures. The reaction mas found to be surface controlled and directly proportional to hydrogen partial pressure over the temperature range studied (400° to 1000°C). A transition in the mechanism occurred at approxirnately 590°C. This has been attributed to a change in the slow step of the reduction reaction resulting from the presence of stable wüstite at higher temperatures. Below 590°C the heat of activation for the reduction was found to be 14,700 cal per mole and it was 3,200 cal per mole above 590°C. THE reduction of the oxides of iron has been a subject of study and interest for many years. Edstrom1 has reviewed the work up to 1953 and his findings provide much basic information concerning details of the reduction of hematite (Fe2O3 ) and magnetite (Fe3O4) with both H2 and CO. He concluded that below 600°C the reduction of both hematite and magnetite was essentially identical, since the rate was controlled by a surface reaction at a magnetite gas interface and the iron formed was very porous. The decrease in the reduction rate for both hematite and magnetite immediately above 600°C was attributed to the formation of a stable wüstite phase across which diffusion was very slow. The wide difference in reduction kinetics for hematite and magnetite above 600°C was explained in terms of the character of the wüstite formed. The rate of magnetite reduction increased slowly with temperature beyond the minimum immediately above 600°C and rates equivalent to those observed at 550°C were not obtained until the temperature was increased beyond 850oC. Edstrom and Bitsianes2 studied the solid-state reduction of magnetite, the reaction of which can be written (4x-3)Fe + Fe3O4—4 FexO [1] where x is between 0.83 and 0.95. The rate was found to be controlled by the kinetics of transport of iron ions through the wüstite phase. Bogdandy and Riecke3 studied the kinetics of reduction of small grains of iron oxide in hydrogen and qualitatively attributed the slow step in the reduction process to the diffusion of hydrogen and water vapor through pores. McKewan4 has analysed the data of Joseph,5 Stalhane and Malmburg,6 and Lewis7 and has demonstrated that the kinetics of reduction of both hematite and magnetite are controlled by surface reactions and also that the variation in surface area during reduction must be accounted for. McKewan was able to correlate the reduction data by the equation rodo[1-(1-R)1/3] = Kt [2] where ro is the initial particle radius, do is the density of the iron oxide, R is the fraction reduced at time t, and K is a rate constant. The applicability of Eq. [2] for temperatures above 600°C where a stable wüstite phase is present, indicates the slow step in the over-all kinetics does not result from diffusion unless diffusion occurs laterally along the oxide metal interface or through a wüstite layer of constant thickness. Diffusional control through a layer of wüstite is unlikely, however, in view of the pressure effects demonstrated by Tenenbaum and Joseph,' Diepschlag,9 McKewan,10 and the results of the present study. McKewan has demonstrated a linear rate dependence on the hydrogen partial pressure over the temperature range 400" to 1050°C for the reduction of hematite.

Jan 1, 1961

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

By R. J. Wasilewski

The resistivity of single crystal and of polycrystalline metal has been determined between 77° and 1500°K. At comparable purity, the resistivity of the poly crystalline metal differs from that calculated from the axial resistivity values. The observed anisotropy is briefly discussed. A zone refined titanium rod was obtained from F. J. Darnell.1 The hardness of this material varied between 52 and 64 Bhn, indicative of its high purity. Single-crystal specimens were cut out from a few large grains, elongated predominantly along <1120>. Resistance measurements were taken with specimens immersed in liquid nitrogen, solid CO,, and acetone, and at ice point, and then recorded continuously between room temperature and 1200" to 1250°C, throughout at least one full heating and cooling cycle at a rate of l° to 3°C per min. Four probe measurements were taken using spot-welded Pt wire 0.003 in. in diam as potential terminals, and the electromotive force drop was determined poten-tiometrically. A standard resistance, in series with the specimen, served to determine the dc current (generally about 80 ma) in the circuit. In order to eliminate spurious thermal electromotive forces, the circuit polarity was automatically reversed at 5-min intervals, and the mean of the two adjacent readings taken as the true electromotive force value. The discrepancy between the readings at reversed polarities was generally of the order of a few µ v, as all the spot-welded joints were contained within a volume of some 5 mm cube. The relative resistance (R T/R 273o) variation with temperature is tabulated below, and shown in Fig. 1, as measured during the first heating run. The discontinuous drop in resistance, corresponding to the a — ß transformation, started for both initial orientations at 1170°K; i.e., some 15°K above the accepted value of 882°C (1155°K). Judging by the temperature ranse of transformation—some 30°K for the single crystal and 20°K for the polycrystal-line specimen—this difference is believed caused by the solution of the oxygen present initially on the surface of the specimens. The general trend of the resistance vs temperature shown in Fi,;. 1 is in qualitative agreement with that previously reported for polycrystalline titanium metal. 2,3 Significant anisotropy is, however, indicated by the crossing over of the curves for <1120> and <0001> orientations at 273°, 650°, and 1000°K. This difference is most startlingly shown in Fig. 2, where instantaneous temperature coefficients (l/R273 x dR /dT) are plotted for both the first heat-

Jan 1, 1962

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior&apos;s Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once an analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at its power plants. A quality assurance program can also help a mine deliver a consistent product to a utility&apos;s power plants. The importance of accuracy, timeliness and consistency are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By Andy Boeckmann

Engineers and owners widely recognize the benefits of foundation reuse - cost savings, reduced construction schedules and reduced environmental impacts, among others. Yet for many projects with existing foundations identified as reusable, reuse is an idea that is discussed at length before cold feet prevail. To address this disconnect, Deep Foundations Institute (DFI) formed the Foundation Reuse Task Force in 2021, which intends to promote reuse, leveraging experience among DFI members and collaborating across pertinent committees. Indeed, the task force includes about 40 members drawn from the Subsurface Characterization for Deep Foundations, Sustainability and Testing and Evaluation committees. One of the first orders of business for the task force was to create a database of successful reuse projects, developing short summary documents highlighting the database projects and recruiting reuse-focused presentations for the ITS Money program. Solid progress has been made on each front: the case history database includes 12 cases so far; the first three summary documents were recently published to DFI's website and foundation reuse projects have been well represented among the past year's ITS Money program. The reuse case history summary documents are available at www.dfi.org/foundation-reuse- case-histories; each of the three is also discussed below. The summary documents demonstrate the feasibility and benefits of foundation reuse. The documents are therefore a useful tool for foundation engineers to share with owners, structural engineers and anyone else who may be hesitant to pursue foundation reuse. The task force continues to welcome new members and anyone interested in joining can contact Andy Boeckmann. The task force is also eager to highlight additional reuse success stories. Anyone with case history information to share is also encouraged to contact Boeckmann.

Jul 1, 2022

By W. L. Fink, L. A. Willey

During the war there was introduced a new higher strength aircraft alloy designated 75S.1,2,3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75.5 alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75s alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. Procedure Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75s "as rolled" sheet (0.064 in. thick). The composition4 was as follows: Weight Percentage Cu Mn Mg Zn Cr A1 with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16-in. id by %-in. od by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064-in. thickness over the junction and adjacent lead wires for a distance of I 1/2 in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3-in. by 9-in. by 0.064-in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75s extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of 3i-in., 2-in., 3-in, and 4-in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 1/2 in. Thcrmocouple~ were peened into the bottoms Of .1/8-in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1949

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country&apos;s primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country&apos;s many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was &apos;subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By Ernest A. Hersam

The small amalgamation-test of the laboratory is not always reliable as a basis for important decisions as to the character and commercial treatment of ores. The conditions of continuous practice on a large scale are not always reproduced in the brief laboratory-test. Sometimes such a reproduction would be very difficult, or impracticable; sometimes it is not even attempted, and the test is performed in a rough way, without regard to the effects of small variations in the methods pursued. The aim of a laboratory amalgamation-test is to learn how much of the gold or silver in an ore can be economically recovered by amalgamation on a commercial scale. The yield can be increased, perhaps, by additional chemical treatment or by extreme comminution of the ore; but this might cost more than the value of such increase. Moreover, in practice, other operations often follow amalgamation; and these operations may remedy a defective extraction by amalgamation, more economically than could be done by directly increasing that extraction. The test should be performed, therefore, upon a uniformly-sized material, and under conditions that are precisely known and capable of being exactly duplicated, or purposely modified. The crucial feature of the test is the effectiveness of the contact made between the gold or silver of the ore and the amal-gamating-surfme. This may depend upon the temperature; the duration of contact; its force, due to gravity or impact; the hardness, plasticity or liquidity of the amalgam; the roughness or other quality of the amalgam-surface; the scouring action of the ore upon the amalgam, or the suspension and

Jan 1, 1905

By Ping K. Di

A naturally aged and synthesized manganese oxide-coated granular media was found in our laboratory to have the capability of the removal of soluble Mn(H) from mine drainage by adsorption and oxidation. Mine drainage commonly also includes other heavy metal ions. Extending this principle, this paper presents the removal of heavy metals including lead, copper, cobalt, zinc and nickel in the aqueous solution by using the synthesized manganese oxide-coated granular media. It was found that the adsorption of lead, copper, cobalt, zinc and nickel on the manganese oxide-coated media follows both Langmuir and Dubinin-Radushkevich adsorption isotherms except in the concentration range less than 0.1 mmole/L. The adsorption mechanism involves the ion exchange between the heavy metal ions and synthesized manganese oxide coated on the media. The synthetic manganese oxide surface has a strong metal binding ability to the heavy metals in the order of Pb2+ > Cu2+ > Ni2+ > Zn2+ > C02+ based on the adsorption results using batch and continuous column operations. The breakthrough curves of these heavy metals showed that the synthesized media could be used effectively in the removal of these heavy metal ions in a cell or packed column. The process can simultaneously facilitate the immobilization of the heavy metals on the synthesized manganese oxide coated media. A subsequent pH adjustment dislodges the heavy metals and regenerates the synthetic media. Thus, the process accomplishes the adsorption, immobilization and concentration of the heavy metal from waste stream in one monolithic procedure.

Jan 1, 1995

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011