Search Documents

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By A. H. Grobe, F. N. Rhines

AT elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible' and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscale forma¬tion) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detail5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the I-b and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 4o alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. EXPERIMENTAL PROCEDURE Silver.-The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By George Haag

El shotcrete tiene una función importante en el sostenimiento y protección de una excavación subterránea. En ese sentido, el presente texto señala los tipos de shotcrete (mezcla seca y mojada) ventajas, clases de equipo, provisión de aire, agua, mangueras, inyectores, la clase de aditivos, los tipos de segregados, los análisis de costos, seguridad, tiempo y otros factores.

Jul 1, 1977

By S. B. Casey

[ ] IN 1880, an electric arc was struck over metal for the first time to experiment with controllable melting. The glare of this arc has reflected on the stacks of the steel industry and continued to light the path of steelmakers in their never ending quest -for faster, more economical, and better ways of producing steel. William Siemens is credited with first employing the electric arc to melt metal in a closed hearth and produce basic metallurgical reactions. By the turn of the century, an Italian, named Stassano, was experimenting with ore reduction by the electric arc. In 1899, Dr. Paul Heroult, in France, used the direct arc principle for producing ferro-chromium. His experiments quickly led him to develop a dosed-top arc furnace for the production of steel, and his first commercial shipment was recorded in December, 1900. American steelmakers, quick to sense the possibilities of this method of melting, invited Heroult to our shores, where, in 1905, he was responsible for installing the first arc furnace on the North American continent. This furnace, at Sault Ste. Marie, was built for ore reduction. But Charles Holcomb, founder of Holcomb Steel. Co. of Syracuse, N. Y. contacted Heroult in 1905 and contracted for the first American direct-arc electric furnace for steelmaking. On April 5, 1906, the first heat was tapped from this 3-ton unit. The furnace was basic lined and powered by a single-phase, 500 kw generator, -producing high amperage at low voltage. It is interesting to note that, although the first few heats were made with cold charges, subsequent heats were duplexed. R. H. Bully, first superintendent of Holcomb Steel, persuaded the directors to purchase the unit to effect a more economical and efficient means of making tool steel by duplexing prime melting in a combustion fired furnace, and transfer of hot metal to the arc furnace for temperature adjusting, refining, and adding carbon and alloying elements. Today, duplexing is foreseen by some as the steelmaking process of the future. The promise shown by America's first arc furnace for ingot production quickly led to the purchase of a similar unit by The Firth Sterling Steel Co., in 1909, and to the purchase of the first arc furnace for production of steel castings, by the Treadwell Engineering Co., in 1911. From its humble start in 1906, production of arc furnace steel has never ceased to increase its yearly percentage of total steel production in the U. S., although certain other methods have declined or almost disappeared. By its ability to be used intermittently, the arc furnace gained favor and enhanced its reputation during depression days. When the attack on Pearl Harbor plunged us headlong into the long days of World War II, the arc furnace stood ready, flexible enough to be overburdened hearth wise 30 pct and power wise 25 pct, pouring its endless flood of alloy for the guns, tanks, ships, and planes which ultimately brought victory. During the post war boom, the now, proven virtues of low initial cost, faster installation, better yield, improved availability, and lower operating cost, enabled industry-particularly the small, new, independent producers-to locate strategically and profitably to meet the demand of an America that had been starved for new homes, appliances, cars, and highways. In the Korean police action, the arc furnace again proved itself by providing the latest alloys metallurgists could develop to meet the demands that the jet age and the innovations of guided missiles required. In today's peacetime prosperity, the arc furnace is continuing to provide the economic flexibility required to meet an ever increasing demand for better steel in the face of mounting costs, scrap shortages, and pressure toward decentralized location of industry.

Jan 1, 1961

Adams, John H., Pres. & Mgr., Alabama Lime & Stone Corpn., 1302-4-8 First Ave., Birmingham, Ala. '14 Adams, L. W., Otis Steel Co., Riverside Plant Cleveland, Ohio. '15 Adams, Leland D., Min. Engr., Mgr., Signal Mines Co., Goldbanks Quicksilver Co., 485 California St., San Francisco, Cal. '14 Adams, R. L., Min. Engr., Old Ben Coal Corpn., Mine 12 Christopher, III. `19 Adams, Robert M., Robert M. Adams Co 1201 Fidelity Bldg., Duluth, Minn. '20

Jan 1, 1925

By J. J. Pelley

NOT being a scientist, an engineer or a metallurgist, I consider it a very great honor indeed to be asked to address the American Institute of Mining and Metallurgical Engineers. Your program indicates that any lack of intricate and technical knowledge on my part in the field of metals will be well taken care of by others. Therefore, I believe any remarks that I have to make might well be devoted to the practical side of metals in railroad service and to the general railroad situation as I view it today. The experiments now being conducted on the railroads with so-called streamlined, light-weight trains and cars would not have been possible had it not been for scientific and engineering research in the past that made these lighter weight metals available. The railroads now have approximately forty units of these new trains in operation. Experi-ence with them will no doubt be a guidepost for future construction in that direction. While the best known experiments are in the passenger service, they are being extended into the freight service. Within the past three years there was constructed for the Association of American Railroads a new standard box car of ordinary carbon steel, in which, by reason of superior design, weight was reduced by 3500 to 4500 lb. under that of existing cars of like capacity. The Association is now testing a box car that weighs approximately six or seven tons less than practically all of the box cars of like capacity in service today. If these tests are successful a very large field for the use of lighter weight metals will immediately be opened, provided the costs of such metals are not too high. The fact that various experiments are being carried on with other classes of equipment constructed with so-called light-weight and non-corrosive metals no doubt will have a considerable effect upon the rebuild-ing of old equipment. The question then will be: How much can we afford to spend on the rebuilding of an old car weighing six to seven tons more than a new car constructed with the latest available materials?

Jan 1, 1936

By John M. Pitt

A rapid in situ stress measurement technique was developed for exposed underground surfaces. The method applies radial stress in small diameter (38mm) boreholes, initiating fracture propagation which is monitored by measuring ultrasonic pulse velocity. Theoretical relations for stress concentrations near boreholes provide independent expressions for unknown principal field stresses at incipient fracture; fracture orientation defines principal stress orientation. Accuracy and precision were evaluated using blocks of brittle material subjected to known stresses. Results were comparable to those obtained by other in situ stress measurement techniques.

Jan 1, 1984

By John G. Ayttes

"The following is a review of the advance of raise boring and its current position. The viewpoint presented is that the mining industry, through its worldwide acceptance of raise boring, has acknowledged the success of the method in general. Acceptance, however, does not imply complete satisfaction with either the equipment or current operating costs. Therefore, a brief review of how boring costs are being r educed is presented, citing examples. Recent raise borer applications of special interest are presented to show adaptability of current equipment, and some special projects in the planning stage are highlighted."

Jan 1, 1972

By Wayne van Drunnick, Mervyn Ruthnasamy, Olvier Guyot, Christophe Bouché

"Anglogold’s Mponeng Mine is situated in South Africa’s North West Province approximately 80km from Johannesburg. The reefs being mined in this area are among the deepest deep level mining operations in the world. These shafts often exceed several thousand meters making these operations complex and expensive.The gold plant is fed with run-of-mine ore which is stored in mill silos. Feedrate to the mills is controlled by a variable speed belt. Three parallel SAG mills (4.85 x 9m) treat 80-100tph, operating in closed circuit. Hydrocyclones classify the mill discharge, returning the oversize to the mill feed. Cyclone feed density and pressure are measured and are used with typical control loops to determine water addition rates to the mill. Control loops at PLC/SCADA level were historically used with limited success in the control of the milling circuits. Mill control for an installation of this type used mill mass (measured by load cells) and feedrate to control throughput. An online particle size analyser (PSI) was installed to assist grind control in tandem with pressure/density control on the cyclones. Although the accuracy of the measured grind was reliable, long term consistency of the PSI could not be guaranteed. Economic pressure from the business sector requires consistent mill throughput at optimum grind conditions. Fluctuations in production targets can manifest due to inconsistent control and the lack of real-time information from the process.This sensitivity to process movements may vary between shifts and also with changes in ore competency.Whilst tools are available to improve control, few have the sensitivity to process movements to provide real-time information for optimal grind control. For this reason an Advanced Control solution was sought. Advanced Control is often described as the supervision of basic PLC/SCADA control. Advanced control systems have to seamlessly compliment the existing control strategy and bridge the gap that exists between basic control and optimised control. A solution was found in the Metso Minerals CISA’s OCS (Optimising Control System). This French designed system makes changes to process setpoints to achieve peak performance and is distinguished from others by its soft sensor capabilities. The soft sensor is an embedded module in the OCS package that can be configured to estimate values normally obtained from field instruments. Advanced control using a Fuzzy Expert System assisted by Statistical tools (such as moving averages and a Soft Sensor using Phenomenological Models) would serve to bridge that gap. Metso Minerals CISA’s OCS is a modular system with various capabilities.It was successfully used to provide on-time process information via Soft Sensors. Circuit stability was achieved using Rule Based Expert Control in complete synergy with Fuzzy Logic. Two rule-based strategies were developed for this circuit. The first uses the online product size analyser as a primary control variable. The second uses a calculated kWh/t value and a modelled mill discharge density as primary control variables. The latter had more availability than the particle analyser and is currently in use."

Jan 1, 2003

By Gabriel S. Esterhuizen, Jarek Jakubec

In 2000, Laubscher’s Mining Rock Mass Rating (MRMR) classification system was updated and published. The new system brought a few fundamental changes that were in direct response to the challenges and problems encountered when applying the classification system in the mining environment, specifically caving operations. The fundamental changes introduced into the MRMR system in 2000 were the abandonment of the Rock Quality Designation (RQD) as an input parameter, accounting for healed and cemented joints, and the concept of rock block strength. The objective of this paper is not to discuss the role and usefulness of classification systems; the fact that classification systems are widely used in every stage of mining projects speaks for itself. This paper discusses some of the experiences gained with the MRMR 2000 system in various mining projects and shows how the changes to the system have resulted in improved assessment of rock mass conditions. Issues related to core logging for rock mass assessment are also presented.

Jan 5, 2007

By M. Moys

The use of temperature measurements for unusual applications in the analysis and control of column flotation and milling is discussed. This is followed by a review of some of the authors current research in the application of the discrete element method to the modelling of particulate processes, specifically milling, fluidized beds and chute flow.

Jan 1, 2005

By W. A. Calhoun

This report gives results of metallurgical investigations performed by the Bureau of Mines on mineral samples taken during April 1959, from Hawaiian bauxite deposits on the islands of Kauai, Maui, and Hawaii. The bauxite samples were tested at the Bureau's Rolla Metallurgy Research Center, Rolla, Mo., to determine if alumina could be extracted. The results were encouraging. Extraction of the alumina by the American Bayer type digest of crude ore samples from Kauai, Maui, and Hawaii recovered 78.8, 73.1, and 70.0 percent, of the total alumina, respectively. These recoveries were increased to 82.8, 85.5, and 79.5 percent by modifying the treatment, which consisted essentially of calcination and weak caustic desilication to provide a residue. The residue was then treated with calcium oxide and digested in a strong caustic solution to extract the alumina.

Jan 1, 1962

By J. I. Jr. Moore

Many articles have been written about the various operations of Britannia mines and mill, as well as treatises on the geology and ore deposits. A partial list of these papers is given below. Most of these papers have covered well the history of Britannia, and have included a thorough discussion of the geology and ore deposits; therefore, in this paper, no account of these subjects. is necessary. However, a short description of the ore deposits will be given as an aid to a clear understanding of the descriptions of the various mining methods. The Ore Deposits The ore deposits at Britannia occur along a shear zone and are five in number, named for the claims in which they lie, as follows: Jane, Bluff, Fairview, Empress, and Victoria. Each of these deposits is called a mine, as they are separated by 500 to 1,000 feet of barren ground. The Jane mine, although the first producer of the Britannia group, has not been in operation for a number of years. The deposit is a silicified replacement in sediments; with very little evidence of shearing. The Bluff deposit is a highly silicified replacement in porphyry, massive and irregular, very hard in the upper 600 feet with practically no shearing, and softer within chlorite schist in its lower 1,000 feet . The Fairview deposit consists of a series of twelve distinct veins or lodes, rather lenticular in shape, and occasionally merging.

Jan 1, 1928

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By Thomas W. Camm

The U.S. Bureau of Mines has developed a system for estimating mining and processing costs as a function of process feed rate with the objective of applying this system to abandoned mine tailings and to evaluate the benefits, if any, of metal recovery. Cost analysis was applied to the mine wastes of Smelterville Flats: an extensive area of mine tailings in the Bunker Hill Superfund Site with high concentrations of lead, zinc, and other sulfide minerals. Results from previous site characterization and metallurgical processing studies were used as the input for the cost analysis. This analysis indicated that processing this site at an optimum production rate of 3,500 short tons per day (st/d) could generate a positive cash flow.

Jan 1, 1993

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By Vineet Kumar Yadav, Akshay Dvivedi, Pradeep Kumar

Near-dry electric discharge machining (EDM) is a process variant of EDM, which uses two-phase flow of liquid and gas as dielectric medium. This article reports the results of an investigation pertaining to the drilling of holes on high speed steel (T2 grade) by a rotary tool near-dry EDM. The One-Factor-At-a-Time (OFAT) approach was used for experimentation. The effects of process parameters, viz. tool rotation speed, peak current, pulse duration, gas pressure and liquid flow rate on material removal rate (MRR) and overcut were investigated. The dielectric medium used was a mixture of glycerin-air. The experimental results reveal that rotation of the tool electrode along with high pressure of two-phase dielectric medium contribute in an effective flushing of inter electrode gap (IEG). Further, in rotary tool near-dry EDM process, higher values of current can be used. This improves process economics in terms of MRR. The MRR measured with rotary tool near-dry EDM was three to four times higher in comparison with conventional EDM. Additionally, appreciable surface quality was achieved.

Mar 1, 2017

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942