Search Documents

By Emil B. Milosavljevic

The photochemical reactions of cyanide ion induced by light were investigated in the presence or absence of a titanium(IV) oxide semiconductor photocatalyst. The light sources employed were the sun and arrays of either mercury or fluorescent (cool white) lamps. The results obtained verify that cyanide decomposes much faster when TiO2 is present in the solution and that it is first oxidized to cyanate. However, contrary to the previous studies, it is established that cyanide is subsequently further oxidized via nitrite all the way to nitrate irrespective of the light source. As expected, the rates of the oxidation processes decrease with the illumination source utilized in the following order: Hg-lamps > sunlight > fluorescent lamps. As nitrate is a significantly less hazardous contaminant than cyanide, complete photocatalytic oxidation of cyanide to nitrate may be a viable method for decontamination of cyanide wastes. Contrary to previous claims, we find that cyanide is slowly photochemically decomposed even in the absence of TiO2. For example, with the mercury lamps as the light source, in two hours, cyanide concentration decreases to essentially zero; up to 7% was converted to cyanate and the remainder to unidentified products.

Jan 1, 1992

By B. R. Mohal, F. F. Aplan, S. Chander

"ABSTRACTThe wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5 ] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3( CH2 )8-C6H4,- ( OC2H, ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3)2-C6H4- ( OC2H4) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 to determine the effect of surfactants on wettability of cotton fibers. In this procedure commonly known as the Draves test, the concentration of a surfactant required to give a 'sink time' of 25 s is determined.Other investigators have used slight variations of the Walker method to study the wetting of fine particles [ 8-12 ] , by measuring the time for wetting a given amount of powder. There are differences in the manner in which the time of wetting is measured, however. Some investigators measure the time for the last trace of coal to disappear [ 8,11 ] whereas others determine the time for the vast majority of particles to sink [ 10 ] . Some investigators report a wetting rate [ 11 ] which is a value calculated on the basis of the time for the 'last traces of particles to sink'. The differences in choice of criterion for wetting can result in different values for wetting rates as illustrated in Fig. 1 which is based upon our measurements of the amount of powder wetted as a function of time. The procedure for wetting rate measurements is described in the next section. The technique in which time for disappearance of the 'last traces of particles' is determined gives the smallest value for the wetting rate, while the technique in which the time for wetting of the 'vast majority' of particles is determined will give intermediate rates. The terms 'last traces of particles' and 'vast majority of particles' are usually not defined explicitly and can lead to large differences in wetting rates measured by different investigators. Since our measurements show that the wetting rates for an assembly of powder decreases with time, we have used the initial wetting rates to compare the wetting behavior of coal in solutions of different surfactants."

Mar 1, 1989

By I. Weir-Jones

[Currently the cost of carrying out 'in situ' geotechnical investigation programmes or installing and operating monitoring systems at construction or mining sites is rising var." rapidly. This is primarily because of our ever increasing labour rates. As a result of this problem efforts are no,, being made develop techniques for the economical; collection of large quantities of geotechnical data relating, to such problems as done stability evaluation, the behaviour of underground openings, or 'in situ' testing procedures. The efforts to reduce the labour content. are particularly apparent in those procedures which have traditionally been manpower intensive e.g. 'in situ' permeability testing where an entire drilling crew and their associated eguipment have been on standby while testis has been carried out; or data collection in underground construction operations where much tine is typically wasted obtaining or maintaining access to instrument sites. In an attempt to illustrate one specialist consulting company's approach to the problem of reducing investigation costs, this rarer examines four recent developments in the field of geotechnical investigation and monitoring which have come about during the last two Years as a result of cur research and development programme. Although these techniques and devices have been developed for specific projects, they all have broad applications in the geotechnical field and they are indicative of the direction in which this company feels developments will take place.]

Jan 1, 1975

By Eric Dussell

Commercial or industrial explosives are mechanically-mixed, fuel-oxidizer composites which exhibit varying degrees of non-ideal behavior. Non-ideality results from a relatively slow and state-insensitive reaction rate (Lee, 1990) and is characterized by C-J pressures, velocities or expansion isentropes significantly lower than those expected from equilibrium, steady-state calculations such as Tiger or BKW (Mader, 1979). This departure results from significant amounts of explosive material which remain unreacted at the sonic point. Energy released by continued combustion within the emergent supersonic region downstream of the sonic point, constrained by local sound speed, cannot flow to the shock front and do work on it. The significant amount of this ‘late energy” and its slow time rate of release must be considered in any blast performance model.

Jan 1, 1997

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By F. Czerwinski

Mechanically fragmented chips of an AZ91D magnesium alloy were transformed into a semisolid slurry within the Thixomolding® system. Microstructural analysis of a material at various processing stages revealed that the cold deformation of the alloy, experienced during chipping, led to the recrystallization and growth of equiaxed grains which were subsequently converted to the globular structures by melting the grain-boundary network.

Jan 1, 2004

By S. A. Wookey

More than 90 per cent of the ore produced by stoping at McIntyre is mined by horizontal cut-and-fill methods. The remainder is mined by square set and fill. In the stopes on the upper levels, mill holes are spaced 80 ft. apart and usually it is feasible to mine the breast for the full distance between the mill holes in one operation and to break, clean out and fill without any support for the roof or walls, other than the odd crown bar or sprag. The ore is scraped to the mill holes by small (10 to 15 hp.) air-operated slusher hoists. No grizzlies are used over the chutes and care is taken to break up the big pieces beforehand. Fill usually is spread by tramming sand or waste in a one-ton car from the fill raise. Fill raises are driven parallel to the strike of the vein and are inclined at approximately 48°. In long stopes, where more than one fill raise is necessary, they are spaced about 300 ft. apart. It is sometimes necessary to stand square sets for a short distance each way under the brow of the fill raise. support needed increases and on the lower levels and in some wide stopes where closer support of the back is necessary, it has become standard practice to timber the stope with 12 by 12-in. timber. Rough timber sets consisting. of caps, tightly blocked to the back and supported on posts 7 ft. high, are placed at about 5 ft. intervals. These sets are generally salvaged from the lower breast before blasting and are used again on the upper slice after the fill has been placed. In general, two or three breasts may be broken down before mucking out and filling and the ground stands long enough to enable this to be done safely. On the lower levels and in certain wide stopes and in heavy ground, a more intermittent method must be used. Only one breast or even part of a breast can be blasted and the back must be timbered before the ore can be removed. In these cases, sill timbers 16 ft. long, supported at one end on posts from the fill and at the other end on pins inserted in holes drilled in the face, are used. Timber cribs 5 by 9 ft. built from the fill to the roof and tightly blocked to the back are used throughout the mine to reinforce both the timber sets and the square sets.

Jan 1, 1946

By Jesse White, Arlin Olson

"An Engineering Scale Technology Demonstration (ESTD) unit utilizing the THOR fluidized bed steam reforming technology was built and operated by Hazen Research, Inc. for the purpose of denitrating and solidifying various Department of Energy (DOE) radioactive tank waste surrogates into granular products. The ESTD offered the opportunity to investigate the operational characteristics of two fluidized beds in series to test process system designs such as those for fluidization, feeding, and product collection. Operational characteristics that were evaluated included bed attrition rate, particle growth, and elutriation; and the effects that variations in process parameters (e.g., fluidizing gas flow rate, feed composition, feed injection method, and gas distributor design) had upon these characteristics were observed. Testing of the process systems on this scale allowed for design changes to be made where the cost in time and money were significantly less by comparison to those same modifications being made on the commercial scale.IntroductionFluidized bed steam reforming (FBSR) offers a moderate temperature (620-750°C) continuous method by which various liquid wastes can be processed irrespective of whether they contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology has exhibited the potential to process these wastes into either a carbonate or crystalline ceramic (mineral) granular product.Pilot scale testing was performed using the THOR Treatment Technologies, LLC (ITT) FBSR process, as it offered the opportunity to evaluate multiple aspects in an environment more conducive to experimentation. Process changes and system modifications could be made faster and with less cost impact as compared with changes to an assembled commercial plant. These aspects include verification of process chemistry and kinetics, evaluation of materials of construction, equipment sizing and design, and the interactions of the systems. Evaluation of process chemistry allowed for the verification of thermodynamic and kinetic models, and was used in conjunction with these models to improve the database and modeling assumptions. It also allowed for the reevaluation of data from earlier bench scale testing with the opportunity for long-term operations. These long-term effects may include the buildup of one or more elements that results in the formation of eutectics leading to the destabilization of a fluidized bed, or the shift in particle size as a result of attrition or agglomeration. The pilot plant also provided an environment to evaluate materials of construction."

Jan 1, 2014

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By Gary A. Halvorson

Plots were established on regraded abandoned mine spoil to determine if nearby good quality spoil could be used in place of topsoil for the reclamation of these sites. Gypsum, calcium chloride, and power plant ash were also tested to determine the effectiveness of these materials in reclaiming these sites. Two sites were selected on which very little vegetation was growing on highly sodic spoil material. Gypsum, calcium chloride, and ash were added to the spoil at a rate designed to reduce the (sodium adsorption ratio) SAR in the surface 15 cm to 10 or less. The good quality spoil (replacement soil) was then laid on the swface at rates of 0, 5 or 15 cm of material. The plots were seeded to a mixture of smooth bromegrass (Bromus enennis Leyss.), crested wheatgrass (Agropyron desertorum (Fisch. Ex Link) Schult.) and alfalfa (Medicago sativa L.). The addition of 5 or 15 cm of replacement spoil significantly improved vegetative growth on these sites. Chemical treatments had no effect on vegetative growth. Weathered ash showed no adverse effects on plant growth or soil properties.

Jan 1, 1991

By R. R. Godard

The practice of dust abatement or control is not new to any operation of United States Steel Corporation. This report will review those activities, past and present, within the five operating districts of United States Steel-Coal Operations with specific reference to mechanical and continuous mining, and including both the health and safety aspects of the problem. Obviously, the first principle of dust control is to inhibit its formation If this is not practical, steps may be taken to prevent its becoming airborne. Airborne dust control can be realized by either collecting it at the point of generation, diluting it with large volumes of air to reduce concentration, settling it by various means, or with reference to ignition hazard only, render it incombustible by neutralization with an inert material. These basic principles have been verified by the work of many, including the Bureau of Mines, U. S. Department of Interior, Bituminous Coal Research, Inc., and the Mining Research Establishment of the National Coal Board of Great Britain. Their application to every day mining problems is best illustrated by the following examples.

Jan 1, 1967

By J. Stiksma, J. Dennett, R. Kalanchey, J. Ji, M. Collins, T. Chan, R. Berezowsky

A pilot plant campaign has been conducted by Sherritt Technologies in support of Eldorado Gold Corporation’s evaluation of pressure oxidation technology for the treatment of refractory gold concentrates from the Certej deposit in Romania. Four separate concentrates, containing 3.5 to 5.4 g/t Au, 13.0 to 14.5% S2- and 12.0 to 32.5 g/t Ag, were tested in the eight-day campaign. The major gold-bearing mineral was pyrite. Preliminary batch tests indicated that gold extraction from the oxidized concentrates in subsequent cyanide leaching was adversely affected by the presence of organic carbon in the pressure oxidation feed when chloride in solution was at an elevated level. As such, the process conditions that were tested during the pilot plant operation were selected to either counteract the negative impact of the organic carbon, or to deactivate it during pressure oxidation. Both process routes proved feasible, yielding gold extraction of 95 to 98% in cyanide leaching of the oxidized concentrates. Silver extraction was typically in the range of 80 to 90%, provided that the oxidized concentrates were also processed in a lime boil step prior to cyanide leaching.

Jan 1, 2014

By M. J. Ferrante

High-temperature enthalpy and X-ray powder diffraction studies were con-ducted on aluminum sulfide (Al2S3) as part of the Bureau of Mines effort to provide new data for the advancement of mineral technology consistent with environmental preservation and energy conservation. Relative enthalpies were measured with a copper-block calorimeter from 298.15 to 879 K. Tabulated values are listed for heat capacity, entropy, Gibbs energy functions, and relative enthalpies between 298.15 and 900 K. Enthalpies were also given in the form of an equation and combined with published data to calculate standard enthalpies of formation and Gibbs energies of formation for reactions of crystalline aluminum with crystalline, liquid, and gaseous diatomic sulfur. The hexagonal, rhombohedral, and cubic phases of Al2S3 were identified by X-ray powder diffraction studies, and the indexed powder diffraction patterns of these phases are given. The hexagonal phase was stable to about 852 K and was partially converted to the rhombohedral form at 879 K.

Jan 1, 1981

By Claudia Castillo, Katja Freitag, Jan Cilliers, Diana Drinkwater, Robert Seitz

The talent gap in mining is not a new challenge. Mining companies continue to seek innovative ways to attract, develop and retain talent, and younger workers are looking for opportunities to develop their professional careers. Training provides a key value proposition for both employees and employers as it helps build a talent pipeline while offering opportunities for learning and growth and value creation. In 2020, Metcelerate launched its 20-month program for early career mineral processing engineers. The program helps develop critical technical skills in the workplace and is a tool to identify motivated engineers and change culture within teams. Learners cap their skills development by executing a technical investigation. This generates immediate value—a win-win outcome for learner and company.

Feb 1, 2025

By N. Rowlands

The importance of mineralogical and chemical characterization of fine particles in the fields of mineral and metallurgical processing is discussed. Emphasis is placed on electron beam analysis techniques including electron diffraction and energy dispersive analysis with special reference to the scanning trans- mission electron microscope. The correct choice of instrument depending upon particle size, composition and nature of sample is stressed and the analytica1 capabilities of different types of instruments are evaluated. Recent applications of electron beam equipment to processing problems are presented and the paper concludes with a review of new developments in the fields of surface analysis and micro-diffraction.

Jan 1, 1985

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.'s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

By Peter Joralemon

I want to limit my remarks to epigenetic ore deposits, but do not necessarily subscribe to the classic theories of hydrothermal ore deposition. I will consider an epigenetic deposit as a primary deposit in which the economic minerals have been introduced subsequent to the formation of the enclosing rock, regardless of the source. Past ore discoveries have been made to a great extent by prospecting techniques that have remained relatively constant over the last many decades. In many cases the discoveries have been enlarged or enhanced with the use of technical tools such as geophysics, but theoretical geology, which should serve as a foundation for exploration, has shown little progress of practical importance since the turn of the century.

Jan 1, 1967

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Mine explosions are one of the most concerning risks related to underground coal mining, as a single gas explosion can cause injuries and fatalities among miners. Underground infrastructure seals and build-in-place (BIP) refuge alternatives (RAs) are employed to isolate an area from active workings to mitigate coal mining-related accident risks. They are designed to withstand blast pressures from a possible accidental detonation of the contained gas or a coal dust explosion. Crosscut seals and BIP RAs, typically consisting of steel-reinforced concrete, are prone to strong convergence and have a significant leakage potential due to high convergence damage near mined-out areas. The roof-to-floor convergence can change the structural integrity of these structures, and altered structural integrity can lead to less explosion resistance capability. Hence, a thorough analysis is needed to further understand their explosion response under various strata conditions.

Jul 1, 2023

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules, under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and. tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment.

Jan 1, 1937