Search Documents

By Arthur Miller, Andrew Weakley, Heather E. Lawson

"IntroductionDynamic failure events in an underground coal mine, or “bumps,” are defined as “the sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillars, or the solid block of coal being thrown into an open entry” (Peng, 2008). Reports of disastrous and often fatal dynamic failure events date back over one hundred years in the United States. Mining practices and technologies have significantly evolved over the course of the last century, yet these events continue to occur. The events at Crandall Canyon, Utah (Gates et al., 2007) and Brody No. 1 Mine in West Virginia (Barker and McNeely, 2014) are two recent failure events that resulted in a total of eleven fatalities. These events testify to the fact that dynamic failure remains an imperative safety concern. Furthermore, their continued occurrences indicate that engineering controls have proven inadequate at wholly mitigating the problem.Multiple conditions have been associated with the occurrence of dynamic failure phenomena, including• thick, competent strata that can create a bridging effect, resulting in high abutment stresses (Rice, 1935; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Agapito and Goodrich, 2000; Peng, 2008; Whyatt, 2008; Whyatt and Varley, 2010)• overburden thicknesses greater than 500–700 ft. (Rice, 1935; Peng, 2008)• a strong coal that is resistant to crushing (Rice, 1935; Peng,2008) or that is “uncleated or poorly cleated, strong…sustains high stress and tends to fail suddenly” (Agapito and Goodrich, 2000)• the presence of sandstone channels or rolls that can serve to concentrate stresses (Iannachione and Zelanko, 1995; Agapito and Goodrich, 2000)• fracturing of strong units above or below the coal seam (Whyatt and Varley, 2010)• slip along pre-existing discontinuities (Peperakis, 1958; Whyatt and Varley, 2010)• multiple seam mining interactions (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995; Newman, 2002; Peng, 2008)• mining sequences that can cause anomalously high stress concentrations (Campoli, Kertis, and Goode, 1987; Iannachione and Zelanko, 1995)"

Jan 1, 2015

By Tom Palangio, Ralph M. Olmstead

Video inspection of boreholes with cameras developed specifically for the mining industry is now possible. These designs are reliable, cost effective, and have the flexibility to be used in other applications.

Jan 1, 1998

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Roy J. Helfinstine, Gilbert H. Cady

One of the most urgent needs in the field of coal combustion is the ability to predict the performance of a coal from knowledge gained from small-scale tests. Numerous types of analyses and tests are conducted on coal, including the proximate and ultimate analyses, heating value, varieties of sulphur, ash analysis, ash fusion temperatures, free swelling index, petrographic analysis, and Gieseler. plasticity. The Illinois Geological Survey has made an intensive study of the value of these tests for judging the performance characteristics of the coal as actually utilized. To date, three reports1,2,3 have been issued, and another is being prepared. The present paper briefly summarizes some of the results found in the studies. Equipment The equipment used for the tests is described in some detail in the above mentioned publications. Briefly, it consisted of a domestic stoker, cast-iron boiler, and water-cooled heat exchanger, which were operated as a forced circulation hot-water system. The entire unit was mounted on scales. Instruments for recording the per- formance of the coal included a hot-water meter to indicate the quantity of water flowing through the boiler; a two-pen, mercury-actuated thermometer to record the temperatures of the water entering and leaving the boiler; a chemical-type meter to record the percentage of CO2 in the stack gases; a pressure gauge to record the static pressure in the stoker-air duct; and a multipoint potentiometer to record the temperatures in the stack and room, and the opacity of the stack gases. A 16 mm motion picture camera was available for taking pictures of either the fuel bed or the scale dial. Procedure The tests described in this report can be conveniently divided into three phases. For the first phase, a load of 5 or 6 tons of unwashed coal (usually screenings) was obtained from each of fourteen Illinois mines. These coals were all crushed and screened to a size of 35 in. (square hole) by 8 mesh. Combustion tests were made on a part of this raw, screened coal. Another portion was passed over a concentrating table to reduce the ash to what was considered to be commercially reasonable, and combustion tests were made on this upgraded coal. The ash content of the remaining coal was reduced to a still lower figure by passing it over the washing table with greater reject, or by standard float-sink procedure. This cleaned fraction was then tested in the stoker-boiler unit. Thus three coals with varying ash content were tested from each mine. For the second phase reported here, coals were obtained from four Arkansas mines and tested as received and after passing over the concentrating table with a normal reject. One Illinois coal was tested in the "washed" condition only. The third phase included tests on commercially prepared stoker coals

Jan 1, 1950

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d'Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

By C Woodward

AT the Belmont mine of the Anaconda Copper Min-ing Co., Butte, Mont., a new double-drum electric main hoist and a single-drum electric auxiliary hoist have recently been placed in operation to meet the demand for greater hoisting depths, and to replace a steam-driven hoist which was inefficient and inade-quate for the new conditions. The ease of operation, safety, and efficient consumption of power of the main hoist all tend toward improved hoisting conditions. It consists of a 2150 hp. d. c. motor, directly connected to a shaft carrying two drums equipped with clutches and brakes. The auxiliary hoist consists of a 1000 hp. d. c. motor directly con-nected to a single drum provided with the necessary brakes. Fig. 1 shows the general arrangement of the complete installation, with idler towers and head-frame. The headframe is built of Bethlehem H and G rolled sections, equipped with two 12-ft. dia. cast steel sheaves for the main hoisting ropes. The sheaves are mounted 129 ft., 6 in. above the collar of the shaft; and above them trolleys are provided for their removal or repairs. Between the headframe and the hoist machinery are two idler towers for supporting the ropes on 3-ft. man-ganese steel idlers provided with roller bearings which fleet on a fixed shaft. As a city street is between- the mine headframe, and hoists, it is necessary to protect the thoroughfare from drippings of the preservative compound used on the ropes which pass over the street. For this purpose, at the point where the hoisting ropes cross the street ,a bridge of trusses, supported on columns and roofed with corrugated iron, is provided from property line to property line. Since one of the idler, towers is set close to the street, a part of the structure is built in-tegral with the street covering. The general design of idler tower as well as the covering over the street is shown at A in Fig. 1.

Jan 9, 1927

By D. R. Gibbons

This morning I would like to speak to you about an area of chemistry that is enjoying a revival-organometallic compounds. This renewed interest, principally stimulated by defense needs, has already created new markets for the products of the mineral industry. Although the consumption of metals in these new products is modest at oresent, several hold promise of importance. Because this is a new and growing market, I am sure the Council of Economics is aware of many of its facets and is interested in new developments. Of course, the chemical industry has been a significant consumer of minerals for many years. I estimate that in 1957 the chemical-industry purchased a total of $1175 million worth of minerals as raw materials (not including fuels). This estimate can be broken down as follows: [Metals and metallic minerals $375 million Nonmetallic minerals (excluding hydrocarbons ) 330 million Hydrocarbons 470 million $1175 million]

Jan 1, 1958

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By K. Sample

Slope stability analysis plays an integral role in the design of various mining applications including waste dumps, heap leach piles, solution ponds, and tailings dams. Generally, limit equilibrium analysis using one of the several prevalent approaches is considered adequate. The density, saturation, and shear strength parameters of the materials forming the slope affect the failure mode and the calculated factor of safety (FS) against sliding. These parameters are generally based on laboratory tests. Field practices and construction procedures are often not completely simulated in the laboratory for various reasons (e.g. equipment limits, time and budget restraints, etc.). This paper presents a holistic assessment of slope stability analysis as practiced in mining applications, using example data from multiple heap leach projects. A sensitivity analysis is presented for variations in material properties, data interpretation, and computation methods. For each step in the design process, the possible variations in parameter values were identified and then used to perform traditional and probabilistic stability analyses. This simple, cradle-to-grave-type approach is used to evaluate the reliability of an example design, and the combined impact of multiple uncertainties on the factor of safety. Example Study The issue of addressing uncertainty in geotechnical design has been discussed in depth by numerous authors (Duncan 2000; Christian 2004; Whitman 1984; Christian et al. 1993). One may ignore the uncertainties involved in a design, take a conservative approach, rely on observational methods (Peck 1969), or attempt to quantify the uncertainty. Geotechnical projects in general, may include a combination of these methods. For important structures, such as heap leach pads, it is critical that sources of uncertainty in the stability analysis be acknowledged early on and considered in the overall design approach. As with any project, economics and other physical constraints, such as space limitation, often do not always allow for an overly-conservative, robust design. In an effort to quantify uncertainty and provide a sense of level of confidence in the safety and reliability of a design, probabilistic methods have been developed and implemented in many slope stability software packages. Reliability methods are often used in the design of open pit mine slopes, but not as commonly in designing heap leach pads and waste dumps. As an example, the stability analysis of a copper heap leach project is presented here to evaluate the effects of multiple sources of uncertainty and differing methods of data interpretation. Some of the parametric values, or the variation therein, are assumed on the basis of actual data from multiple heap leach projects, included in the paper as well. A generic representation of the example case study is shown in Figure 1. As depicted in the cross-section, the ultimate height of the design is 114 m (measured from the crest to the toe). The overall slope of the heap leach pad is 1.88 horizontal to 1 vertical (1.88H:1V), or 28°. The slope benches are considered in the overall slope. The example leach pad is founded on alluvial, colluvial and residual soils overlying weathered limestone. The ore to be placed on the pad is characterized as poorly graded gravel (GP) with average fines content (percent passing #200 sieve) of 4%. The liner subgrade is low permeability (fine) soil. The cover or the drainage material, placed directly above the geomembrane (between the liner and the ore), is crushed ore in this case. The phreatic surface was assumed to be 1 m above the base liner, which is what the collection system over the liner is typically designed for. [ ] In heap leach pads, typically, Linear Low Density Polyethylene (LLDPE) or High Density Polyethylene (HDPE) is used as the base liner. The decision is based on the elongation, strength and other requirements of the application as well as economic considerations. In this example study, the base liner was 80-mil single-side textured LLDPE. FIELD INVETIGATION AND SAMPLING When selecting appropriate values for the input parameters of the stability analysis, the level of uncertainty in the data and the assumptions that are made must be clearly identified and considered in the design. This concept has been emphasized through an extensive number of publications regarding geotechnical uncertainty and reliability (Christian et al. 1994; Duncan 2000; Christian 2004). The primary source of uncertainties involved in slope stability analysis for mining applications is inadequate geotechnical investigation, often lacking in a thorough assessment of in-situ material characterization and sampling disturbances. To emphasize this point, some background information is presented here. The tradeoff between the costs of a thorough site investigation versus the risks of design uncertainty has long been a challenging management decision in geotechnical projects. For mine sites, significant investment is typically made in exploration and estimating mineral resources and the geology of a mine site is often more thoroughly documented than other types of geotechnical projects. Nevertheless, the engineering properties of the soil and rocks relevant to slope stability receive less emphasis. Baecher and Christian (2003) observed that the areas of geotechnical concern, such as slopes and waste disposal facilities, are usually associated with mine costs rather than revenue, and therefore, significantly less money is devoted to their site characterization and laboratory testing. The expenditure for site investigations varies significantly from project to project, with higher levels of uncertainty and, therefore, the

Jan 1, 2009

By G. B. Gibbs

Equations are developed which describe the growth of graphite nodules during a-phase graphi-tization under various limiting conditions. When carbon diffusion is rate controlling a modified Birchenall-Mead equation predicts an "apparent activation energy" of 31 keal mole-1 for the parabolic growth constant. If reaction at the graphite or cementite interface is the slowest process growth kinetics are linear and the activation energy must be >50 keal mole-1. A comparison with the experimental observations confirms that carbon diffusion determines the rate of reaction. Apart from minor approximations associated with Lou! carbon solubility in a iron the theory may also be applied to I-phase graphitization. It is well-known that cementite exists as a meta-stable phase in Fe-C alloys and that if a specimen is held at diffusion temperatures for a sufficiently long period the cementite decomposes and graphite is precipitated. Graphitization occurs by the nu-cleation and growth of carbon nodules and several impurity elements catalyze the reaction when present in minute amounts.1 The growth kinetics of nodules have been extensively investigated in the fee ? range2, 3 and recently in the bee a range.1, 4 Experimental growth curves (nodule radius vs time) have slopes which decrease with time, but the scatter of points is generally too great for the precise shape of the curves to be determined with certainty. Birchenall and Mead5 concluded that they are parabolic in ? iron, indicating diffusion control, and that the migration of carbon atoms determines the growth rate. Harris et al, 1 advanced similar ideas for a-phase graphitization. On the other hand, Burke3 chose to regard the initial growth region as a transient followed by a linear law indicating interface control (i.e., cementite decomposition or graphite crystallization as the slowest process). Jeminson and Higgins6 originally considered the initial steep portions of "parabolie" to represent a linear growth law also. In support of these ideas it has been noted that the apparent ac-

Jan 1, 1965

By D P. Telionis, P P. Vlachos, R-H Yoon

Industrial processes involving multi-phase flows such as flotation require understanding of the relationships between bubbles, solid particles and the flow. Modern experimental tools are employed in this effort to measure with great accuracy the basic features of the motion of all three phases in turbulent flow. We employed a unique digital particle image velocimeter (DPIV) that can record with great accuracy and kHz temporal resolution, velocity vectors of all three phases, namely the fluid, the solid particles and the air bubbles. The interaction of these three phases was studied in homogeneous isotropic turbulence generated by cylindrical grids. Particles and bubbles were released into the turbulence and the motions of the three phases were monitored. The experimental results obtained in the present work were compared with the predictions of the models published in the literature.

Jan 1, 2005

By Bruce Geller

Attending the Prospectors and Developers Association of Canada (PDAC) meeting and exhibit has become an annual tradition for many in the mining industry. Similar to last year’s synopsis, this report is an overview of the 2003 conference from the eyes of a consulting mineralogist. It is supplemented by conversations with other participants. And it examines the conference handouts. Certain segments of the mining industry have seen improvement throughout the year in terms of metal prices, stronger demand and renewed interest by the investment community. Other segments continue their decline due to depressed commodity prices, higher oil prices, a continued weakness in the global economy and war uncertainties. SARS was known to the world, but it was not a Toronto epidemic during PDAC. In short, this year’s PDAC was permeated by an air of anxiety about the Middle East.

Jan 1, 2003

By John W. Cahn, David A. Karlyn, Morris Cohen

The massive B(bcc) — am (fcc) transformation in Cu-Zn alloys has been studied isothermally by pulse-heating the retained ß phase from room temperature to the reaction temperatures. The transformation is found to occur only in the single-phase a region of the equilibrium diagram. The massive growth rate is of the order of 1 cm per sec and is constant at each temperature, usually after a delay time of some milliseconds. The delay time depends on the reaction temperature in C-curve fashion, while the growth rate increases monotonically with temperature over the single-phase range. The absence of isothermal massive transformation in the two-phase region does not arise from slow growth rates at such temperatures, but because the reaction cannot get started there. It is proposed that the massive transjormation initiates at small preexisting a particles which have rejected zinc into the surrounding 0 matrix. Only within the single-phase region can these particles consume the excess zinc during diffusion-controlled growth and thereby accelerate to the steady-state massive growth rate. The onset of massive growth marks the end of the delay time, and the growth rate then becomes interface-controlled. These isothermal transformation characteristics explain why the usual composition range for massive-kinetic studies by quenching is so limited. The same principles can be extended to more complex alloy systems by recognizing that the single-phase region in which the massive transformation can occur may not be stable with respect to phases not participating in the reaction. MASSWE transformations are now recognized as a regular class of solid-state reactions involving no compositional change (like martensitic transformations) and no shear displacements (unlike martensitic transformations). The name was first coined by Greninger1 in 1939 to describe the coarse grains of fcc a solid solution generated via a fast reaction from the parent bcc 0 solid solution in Cu-A1 alloys. However, some 9 years earlier, phillips2 had already described a similar transformation in the Cu-Zn system. The fact that the massive a formed as a single phase during drastic quenching from the 0 region of the equilibrium diagram signified that compositional changes were precluded. and the reaction was presumed to take place as in a one-component polymorphic transition by nucleation and growth. Phillips also observed that the occurrence of the massive transformation in the Cu-Zn system was extremely sensitive to alloy composition. For example. in a Cu-37.3 at. pct Zn alloy. the ß — am (am = massive transformation product) reaction was found to predominate and was not suppressed by iced-brine quenching from the 0 region. whereas at compositions greater than 38.3 at. pct Zn the massive reaction did not appear at all. Knowledge concerning massive transformations has bee11 substantially enhanced over the years by Massalski and his coworkers; an excellent summary of his papers and the current understanding of this type of reaction has been published recently by Barrett and ~assalski." he massive transformation product grows in roughly nodular form. often with irregular boundaries but sometimes with almost planar interfaces. The latter may have simple crys-tallographic indices relative to the 0 matrix. or the indices may be complex just as in the case of mar-tensites.'1 Little is known about the existence of orientation relationships between the massive and parent phases. A striking feature of massive transformations is that the massive units start almost exclusively at grain boundaries of the parent phase and frequently propagate on a broad front across matrix grains and grain boundaries of various orientations. Because of the rapid growth rate, it is thought that the interface motion is controlled. not by long-range diffusion. but by thermally activated atom jumps across the transformation boundary.

Jan 1, 1970

By Scott Orenstein

Construction blasting has allegedly been the cause of property damage in the following situations: (1) When the detonation of the shot hurls rock and debris into the air that causes property damage upon impact; and (2) When property owners notice cracks in their walls and foundations after they experience the momentary vibrations that coincide with the detonation of the shot. The current state of the law for both these situations is firmly established. Blasting is classified as an abnormally dangerous activity, for which the blaster is held strictly liable, whether the damage is the result of flying debris or vibrations and concussions generated by the blast. It is when the alleged blasting damage is supposedly from concussions and vibrations, however, that the courts usually reach the wrong result. The typical scenario involves property owners that thoroughly investigate their property after feeling blast generated vibrations, and find cracks that they believe did not exist beforehand. Most often the truth is that the property owners have never noticed these cracks before because they have never looked that closely before. Any structure has a certain number of cracks due to a variety of causes, such as settlement overtime and temperature and humidity changes.

Jan 1, 2004

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By M S. Tuohy

Poorly judged or under-appreciated change plays a role in many major accidents. In particular, operational changes related to continuous improvement, maintenance and introduction of new technology can lead to unintended safety (and other) consequences. This paper provides an overview of the role of management of change in preventing unwanted impacts on safety, community relationships and the environment. It draws on a range of incidents covering mining, minerals processing, refining and smelting where inadequately assessed or ineffectively implemented change led to significant safety, environmental or community consequences. The paper will also highlight cases of well-managed complex change and the underlying model of decision-making in place to make those decisions. All these examples are drawn from Atturra’s experience in response to accidents or working with sites to improve their management systems. The paper will report on the challenges of applying conventional risk assessment approaches to complex or technically significant change. These typically result in either onerous and lengthy change procedures that are prone to workarounds or poor implementation. Conversely, ‘light touch’ or efficiency driven change processes present the risk of intended consequences by failing to bring appropriate expertise to bear in decision-making. Such balances can be resolved by considering the designation of ‘technical authority’ with appropriate expertise to consider the change and deconflict any production, cost or schedule trade-offs. Finally, the paper will reflect on the key components of management of change systems in the context of major accidents, highlighting good practice in how they are implemented. This will consider the integration of existing corporate processes, risk management and organisational structures into management of change systems, not just the content of change forms and procedures.

Apr 16, 2024

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.