Search Documents

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

Discussion following the presentation at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, included the author's introduction, written contributions by Bedson P.P., Gregory T.W.D. and Morgan J.D., oral contributions by Louis H., Greener T.Y. and Severs W., and the author's reply

Dec 1, 1916

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

By C. M. Iheagwara

An overview of the scope and ramifications of scrap recycling in the Nigerian metallurgical industries has been presented in this paper. The modern state-of-the-art processing techniques and the operational strategies employed in the recycling plants are discussed. Optimization techniques for cost effective recycling operations are highlighted. As new units within existing metallurgical plants and new metal working plants approach commercial operations, expansion of existing recycling plants and the emergence of new ones have been showing to hold the key to their profitability from the raw material standpoint. The present economic predicament of the entire industrial sub-sector, lack of sufficient foreign exchange to procure new machineries and the emergence of a maintenance culture have triggered a phenomenal increase in the number of spin-off industries which depend on metal recycling activities. This, it is argued, widens the horizon for scrap processing/recycling.

Jan 1, 1992

By Louis H. Berkelhamer

"INTRODUCTION ""Free silica"" includes all free forms of silicon dioxide, such as quartz, chalcedony, tridymite, cristbbalite, opal, diatomaceous earth, and lechatelierite. The term, has been used rather loosely however, as synonymous with quartz, as quartz is the most abundant form of free silica. ""Combined silica,"" on the other hand, has been reserved to denote silica combined with other elements as silicates.Improvements in methods for the determination of free silica, and quartz in particular, have been the subject of considerable interest during the past decade, owing mainly to the accented and increased knowledge concerning quartz as a causative factor in silicosis. Analysis for quartz, however, is of importance in many other fields, including the determination of quartz in ceramic raw materials, such as feldspar and clay; the evaluation of a beneficiation procedure by the ore dresser, such as in the concentration of iron ore; control studies of a manufactured product, such as silica brick; and routine analysis of rock, mineral, and ore samples by chemists and petrographers."

Jul 1, 1944

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By Marie-Aline Van Ende, In-ho Jung

A thermodynamic database for the oxyfluoride system CaO-MgO-Al2O3-SiO2-Na2O-K2O-Li2OMnO- FeO-F has been developed based on the critical evaluation and optimization of all available experimental thermodynamic and phase diagram data. The developed database can be used for phase diagram and equilibrium solidification calculations for multicomponent systems and for understanding the solidification behavior of mold fluxes. Based on this thermodynamic database, a simple kinetic model was developed to simulate the interactions between the mold flux and molten steel using effective equilibrium reaction volumes combined with the thermodynamic database.

Jan 1, 2014

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

A preliminary program dated April 25, 1974 was prepared for Development Engineering, Inc. (D.E.I.) on research and development, laboratory; field and other engineering studies for the disposal of retorted oil shale. This program was revised and published as a final document dated December 17, 1974. The document included a discussion on the peculiarity of retorted shale materials to be investigated and a discussion of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The proposed research and development program was divided into eight work phases as follows: I - Program Development II - Exploratory Laboratory tests on old U.S.B.M., retored shale III - Laboratory tests on Pilot Plant retorted shale IV - Laboratory tests on retorted shale from Semi-Works Plant, and field and test plots and ponds. V - Field compaction tests

Jan 1, 1975

By Aner W. Erickson

"Preliminary examination of tungsten deposits on the Mountain View property near Hyder, Alaska, was made by Neal M. Muir, an engineer of the Bureau of Mines daring the summer of 1942. Fifteen samples were cut, rough esti¬mates of ore reserves were made, and it was proposed to extend the drift on scheelite-bearing vein 300 feet in a northwesterly direction.From May 22 to October 24, 1944, an exploratory project was conducted on the property by the Bureau. In the course of this work, the camp buildings were rehabilitated; the dam, hydraulic line, and machinery were repaired; 226 feet of drift was driven; 80 groove samples aggregating 3.9 tons in weight were cut; a 6,000-foot surface and underground traverse was run; and the area was mapped in detail.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is doe Neal W. Muir, project engineer, and Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for their supervision of the field work and revision of the report.Acknowledgment is also made to Silbak Premier, Ltd., for rendering valuable assistance in the repair of equipment and for extending various courtesies to Bureau of Mines personnel during the conduct of this project.The Mountain View property is located at latitude 55° 59' north, and longitude 130° 03' west in the Salmon River mining district of southeastern Alaska, about 5 miles in a northwesterly direction from the town of Hyder, which lies at the head of Portland Canal, as shown in figures 1 and 2. Vein outcrops and surface workings are at an elevation of 950 feet and occupy the west flank of a low ridge between Skookum and Fish Creeks, as shown in figure 3. The portal of the long adit exposing the vein at depth is on Skookum Creek about 550 feet north of the confluence of Skookum and Fish Creeks.Access to the property is over a 4-foot wide trail built and maintained by the United States Forest Service. This trail is suitable for pack animals and is adequate for transportation of supplies and material for exploratory work. During the periods of camp construction and past exploratory operations a 4,000-foot, single-cable, aerial tramway, now in disrepair, served for transportation of materials and all machinery from the Salmon River Highway to the property. The cost of such hauling was high, amounting to $12 a ton. Topography is suitable for construction of a ""cat road"" 2 miles in length, connecting the property with the Salmon River Highway. It is estimated that such a road could be built for $5,000 a mile, and supplies, machinery, and concentrates could be haled over it at a cost of less than $2.50 a ton."

Sep 1, 1946

By M. E. Kundick, W. E. Dieter, L. Cohen

The major details of design and maintenance of a seamless stainless steel fume hood system , developed by the Bureau of Mines , are described and illustrated . Operating and housekeeping routines are outlined .

Jan 1, 1964

By P. N. Summerfield

This report describes the first phase of a general investigation designed to ascertain whether an electronic roof-testing device can be developed that will improve the ability to detect "loose" or "drummy" roof rock over that possible by striking the roof with a sounding bar and noting the character of the air vibrations with the unaided ear or the rock vibrations with the fingers. The amplitude, frequency content, and duration of the vibrations produced by striking solid and drummy roof rock with a hammer or sounding bar have been measured. Results disclosed that there is a significant difference between the characteristics of the vibrations produced in solid and drummy roof. This difference is such that the design of an electronic device to indicate quantitatively the condition of the roof rock appears possible. INTRODUCTION The conventional method of roof testing consists of striking the roof with a bar2/ and judging its soundness from the character of the air vibrations heard with the ear and/or the rock vibrations felt with the fingers -a procedure that depends upon the experience and the sensory abilities of the observer. Impact testing of a solid roof rock usually produces a sharp ping or click, whereas impact testing of a drummy roof rock produces a dull thud or drummy sound. This method of roof testing is, at most, only a qualitative test, and many roof rocks are difficult to classify as drummy or solid.

Jan 1, 1956

By M. Lindgren

"Hydrometallurgical processing involves process stages, like leaching, that create harsh environment for stainless steels. High acidity, the presence of chlorides and oxidizing ions combined with relatively high temperature create risk for both uniform and localized corrosion. Advanced electrochemical techniques were employed to study uniform and pitting corrosion of two stainless steel grades 316L and 2205. Results obtained with the linear polarization resistance technique combined with the harmonics distortion analysis, electrochemical noise and coupled multielectrode array systems are compared to the results of conventional electrochemical techniques and immersion tests.INTRODUCTIONHydrometallurgical processing has become favoured in metals production in recent years due to energy costs, leaner ore bodies and environmental factors. Because the hydrometallurgical processing route is flexible, various types of secondary raw materials, like flotation tailings, dusts, sludges and slimes can also be treated in addition to conventional mineral concentrates (Sarveswara Rao & Acharya, 2008).Hydrometallurgical processing relies on aqueous chemistry, usually acids, at temperatures around 100°C for the recovery of metals from ores, concentrates, recycled or residual materials. The processing route can typically be divided into three stages: leaching, solution concentration/purification and metal recovery. The processing environment is aggressive, especially in leaching. High acidity, relatively high temperature together with impurities, like chloride ions, place high demands on the corrosion resistance of construction materials. The dominant corrosion mechanism may be uniform corrosion or localized corrosion depending on the process conditions (Ekman & Torsner, 2010). This complicates the prediction of corrosion rates and, consequently, cost effective material selection.Traditional means to evaluate uniform corrosion resistance of stainless steels are immersion tests and the results are published in the form of iso-corrosion diagrams (Outokumpu Stainless, 2010). For the localized corrosion, namely pitting and crevice corrosion, immersion tests can be used but the duration of the test is rather long because an incubation period takes place prior to the occurrence of the actual localized corrosion damage. Electrochemical techniques, traditionally in the form of cyclic polarization scans, have been employed to assess the susceptibility of a material to pitting corrosion (Papavinasam, 2008). They cannot, however, give any indication of the pitting corrosion rate and lack potential for on-line measurements."

Jan 1, 2012

By LESTER W. STRAUSS

FOR fifteen months after the other dominions of the British Empire and the entire so-called sterling 11loc loosed the shackles that bound the111 to the gold standard, South Africa, giant among gold-producing nations, remained stubbornly attached to gold at the traditional ratio of 85 shillings in currency to one ounce of gold. But eventually even South Africa had to heed the dictates of trade and the obvious interests of its great gold-mining industry. In December, 1932, South Africa's currency severed its golden bonds. Today the South African pound is 011 a par wit11 the British pound.

Jan 1, 1935

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011