Search Documents

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By K. Lapakko

Kinetic tests results are influenced by methodological variables, including test duration and mine waste particle size. Some samples tested produced neutral drainage in kinetic tests for more than two years prior to drainage acidification. The potential for long "lag times" can be assessed based on the mine waste mineralogy. The lag time duration can be estimated using this mineralogy in conjunction with dissolution rates observed in the kinetic tests. The influence of particle size on the drainage quality is dependent on the variation of the availability of acid-producing and acid-neutralizing minerals with particle size.

Jan 1, 1998

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By Jean J. Tancous

Chromium recovery from wet-blue offal trimmings and shavings can be done with substantial chemical cost gains by incineration at 600° C for 5 hr. Pretreating the offal with 0.5 M Na2C03 and air-drying prior to incineration produce Cr04 .By simply incinerating the offal, without pretreatment, an ash containing water insoluble Cr203 was produced. The Cr203 in the ash was purified by leaching with water. Chromium and crude protein were efficiently extracted from offal using 5 pct Na103, 5 pct H2S04, and 3 pct NaCl at 40° C. This procedure was effective but expensive. Satisfactory leather as to odor, appearance and shrinkage temperature was made from chromium recovered from wet-blue offal by incineration and by extraction. Chromium conservation is possible by recycling chromium liquors and by precipitating chromium from spent tanning liquors prior to combining these liquors with other tannery wastes. Combining chromium liquors with other wastes introduces contaminants that make chromium recovery and reuse difficult. Leaching sludges with H2SO4 produced marginal chemical cost gains. Leather tanned with these solutions had satisfactory shrinkage temperature but the sludge odors and iron contamination were objectionable.

Jan 1, 1979

By H. F. Yancey

The Baum-type jig used so widely to clean bituminous coals has not been adopted for anthracite. If proved suitable for anthracite, its use might lower preparation costs in some plants. Cleaning trials on a Pennsylvania anthracite in a laboratory-size Baum-type jig were undertaken by the Bureau of Mines to provide indicative information that would be helpful in determining whether the cost of a full-scale installation would be justified. Clean coal surpassing standard anthracite specifications was obtained in all sizes from Stove through No. 5 Buckwheat. Recovery effi¬ciencies were acceptable down to 3/16-inch size, but there was excessive loss of coal in the finer sizes. Thus the fine refuse produced in a commercial plant might re¬quire retreatment. A comparative cleaning trial in a dense-medium pilot plant provided a recovery efficiency only l percent higher than obtained in jigging.

Jan 1, 1957

New Trade Status for Mainland China--On January 24, the Congress approved a most-favored-nation trade status with Mainland China for both imports and exports. A Presidential Proclamation had been issued earlier in anticipation of the Congressional action. Import duties on such commodities as tungsten, mercury, and antimony are automatically decreased. Defense Production Act Extended--The Defense Production Act of 1950 was extended 60 days to March 28, 1980. The provision for the usual 2-year extension of the Act is reportedly included in an omnibus energy bill that is tied up in committee. The Act under Title III provides for the expansion of productive capacity and supply and, more specifically, it gives priority to defense contracting where defense and non-defense interests conflict

Jan 1, 1980

By Rick Wilkins

The stability of steep embankments is a major safety issue in open pit mining, highway passes, and earth filled dams. A failure in any one of these situations could mean a loss of very expensive equipment, a long term inconvenience, and more importantly, a loss of life. These possible catastrophes could be avoided by installing a reliable real time monitoring system. Robotic total stations (RTSs) give one possible cost effective solution to creating a near real time monitoring system. Repeated surveys at predetermined time intervals can automatically generate warnings if slope movements exceed a preset tolerance level. The variation in atmospheric refraction, combined with possible instabilities in reference targets, can make a monitoring system based on RTSs produce false alarms. A methodology has been developed at the Canadian Centre for Geodetic Engineering (CCGE) for reducing these systematic error effects. The methodology has been realized in the creation of a software package that has been successfully implemented at large earthen dams in California and at an open pit mine operation in British Columbia.

May 1, 2002

By Joan Weinberg

The real gross national product (GNP) expanded by 2.3% during the second quarter, down from the anomalous 4.4% growth rate in the previous 3 months. If the expansion continues through October, it will have lasted 5 yr and become the second longest in 40 yr.2 As in the first quarter, improvement in U.S. exports played a role in the continuing--albeit slow--growth. More than 2 yr of declines in the dollar relative to currencies of other industrial countries have contributed to a slight reduction in the trade deficit in real (volume) terms, as real net exports of goods and services rose $1.9 billion (table 1). Exports grew a strong 12.1% while imports, which had fallen the previous two quarters, rose 7.4%. Manufactured goods and petroleum products accounted for most of the second quarter import increase. The American Petroleum Institute estimates that the volume of crude oil and refined products imports in the first half of 1987 surpassed those in the same period last year by 7.5%, reflecting falling domestic production and higher than expected demand. Expenditure on durable goods--those that last at least 3 yr-by both consumers and producers also contributed to the second quarter expansion. Personal consumption of durable goods rose 9.0%, after having fallen the two previous quarters. Motor vehicle purchases accounted for most of the second quarter increase and the first quarter decrease. Sales of automobiles surged in the last quarter of 1986, as consumers rushed to capture the sales tax deduction that was eliminated on January 1. Sales fell in the first quarter of 1987, but have now moved closer to the trend line exhibited in the first three quarters of 1986. Automobiles accounted for half the 0.8% July gain in retail sales, and two-thirds of the 1.4% June gain. Producers durable equipment purchases also rose this quarter, accounting for the increase in nonresidential fixed investment.

Jan 1, 1987

By Huyang Xie, Rishi Raj, Vera A. Versteeg

"A new method for MOCVD has been developed in which a precursor solution is directly injected into a reaction chamber. The vaporization of short pulses of liquid is facilitated by atomization with a piezoelectrically-operated nozzle. The system has been used successfully to grow oriented, thin Ti02 (rutile) films on sapphire substrates with the crystalline relationship (101)[010]R I (1120)[0001]s. A growth rate of approximately 2 monolayers per pulse was achieved at 650°C for a reactant impingement rate of about 800 monolayers per pulse. Also, epitaxial LiTaO3 thin films were grown on (0001) sapphire from a single source, bimetallic precursor, lithium tantalum hexa-t-butoxide as the precursor. X-ray diffraction shows that the LiTaOa c-axis is normal to the sapphire surface. The x-ray pole figure and crosssection TEM diffraction show that the films were also in-plane oriented, with sapphire [1010] parallel to lithium tantalate [1010]. These films are shown to have extremely low optical attenuation, and refractive index that compares well with bulk values.IntroductionMetalorganic chemical vapor deposition (MOCVD) techniques have come into increasing use in recent years, due to the growing versatility and availability of precursors and improved environmental advantages over the halogenated compounds used for conventional CVD. Most commonly, the films are deposited by dissolving the metalorganic reactant (typically a metal alkoxide) in a carrier gas, which is carried through heated lines to a heated substratel . The metal alkoxides decompose by pyrolysis, leaving the films on substrates. While this method has been used to produce excellent epitaxial and heterepitaxial films, it has the disadvantages of complexity: the precursor must be heated to fix its vapor pressure, the gas flow rate carefully controlled, and the carrier lines heated to prevent condensation before reaching the reactor. Additionally, this conventional method cannot be used with certain low-volatility precursors that decompose upon heating."

Jan 1, 1994

By M. S. Lee

A cold model study on the effects of various operating conditions on the dispersed-phase holdup in a liquid-liquid emulsion generated by bottom gas injection has been performed using water and kerosene. Dimensional analysis was used to correlate the holdup with the operating conditions and the sampling locations. The holdup increased with gas velocity, and decreased with axial and radial distances. The radial distribution of holdup follows a Gaussian function. The holdup increased with increasing ratio of the heavy phase to light phase volumes and decreased with the total height of the heavy phase. The combined effects of various operating conditions can be represented by the Froude number. The variation of the holdup within the plume was correlated by a single equation involving a set of dimensionless numbers.

Jan 1, 1995

By C. E. T. White

Although trace amounts of Indium are found in many ores, commercial production of the metal has come almost exclusively from residues, flue dusts and slags generated by Zinc recovery operations. Our paper attempts to summarize the various approaches used to recover Indium from these by-products. Some comments on production and price trends are included as well as our views on future availability.

Jan 1, 1982

By L. Garner McDonald

The U.S. Bureau of Mines, under contract to the U.S. Department of Energy, investigated the erosive-wear properties of seven commercial alloys with potential applications as valves for coal-conversion plants. A dry particle, jet-erosion apparatus was used to determine the wear of seven materials: 316 and 440-C stainless steels, K-68, K-701, and K-801 cemented tungsten carbides, HC-250 white cast iron, and Haynes 6B. The alumina abrasive entrained in the nitrogen gas jet had particle sizes of 27 or 50 µm, the abrasive velocities were 55 to 170 m/s, and the particle impingement angles were 15° to 90°. The maximum specific wear for ductile materials was found to occur at impingement angles of 15° to 30°, and the minimum specific wear occurred at 60° to 90°. For the brittle materials, maximum specific wear occurred at impingement angles of 50° to 85° and minimum specific wear was at the lowest angles. As the velocity and erosive particle size increased, the specific wear increased. The specific wear was related to the velocity by the power function WocAVn, where n was 1.8 to 3.9 for ductile materials and 1.8 to 3.6 for brittle materials.

Jan 1, 2010

By André de Almeida Grilo

Correias transportadoras de alta temperatura são ativos críticos para a pelotização devido ao prejuízo que sua falha pode trazer para a produção. Nesse sentido, deve-se avaliar a vida útil da correia em uso, visando, principalmente, auxiliar sua manutenção, e nesse contexto o presente trabalho tem como proposta utilizar a caracterização dos componentes e o estudo da degradação térmica do material da cobertura de correias transportadoras de alta temperatura. As caracterizações foram realizadas de modo comparativo entre três tipos distintos de correias transportadoras de alta temperatura fornecidas para a VALE S.A. Os reforços das correias foram caracterizados por FT-IR para análise qualitativa do polímero. De maneira semelhante, as borrachas foram caracterizadas por meio da análise do produto de pirólise via FT-IR e a densidade de ligações cruzadas por meio da técnica de inchamento do polímero e aplicação da equação de Flory-Rhener, o que ajudou a justificar o comportamento das diferentes marcas de correia perante a degradação térmica, estudada em um trabalho anterior. A partir desses resultados e utilizando dados de variação das propriedades mecânicas do material em função do tempo e temperatura de processo, pôde-se avaliar a taxa de dano causado a cada correia e, aplicando-se dados reais de processo, avaliou-se o desempenho das correias em trabalho.

Aug 8, 2018

By Dai Wang

Stoppings are necessary ventilation control devices for effective air distribution underground. However, one of the major problems underground mining has is that every stopping is a potential leaking source. Since air always flows from a point of high pressure to one of lower pressure, and the total pressure at every point in intake airways is higher than that in the return airways, air will always tend to leak from intake to return (Tien, 1996). In many mines, less than half of the air entering the mine actually gets to the working areas; the rest of it simply short-circuits directly to return airways through leaky stoppings instead (Timko and Thimons, 1983). Leakage through a stopping occurs because of pressure drops across the stopping and available leaky path in stoppings. Empirical equation has been widely used to characterize the relation the amount of leakage and variables that affect leakage. However the use of this equation requires accurate information for constants which are not always readily available. It is the attempt of this paper to derive an equation similar to the Atkinson Equation that can readily be applied to characterize pressure-leakage relationship for any given stopping.

Jan 1, 1998

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016

By Dean. R. S.

The work of the copper metallurgy section during the year was devoted to laboratory studies of sulphur recovery from smelter smoke and combination smelting of copper and manganese. Both of these subjects were new this year. Combination Smelting of Copper and Manganese According to published work, the affinity of manganese for sulphur is greater than that of iron for sulphur, so that if a suitable mixture of com-pounds of iron, copper, and manganese be smelted to form a matte and slag, manganese should concentrate in the matte, together with copper.

Jan 1, 1937

By Gus Van Weert

Hydrometallurgical oxidation of sulphides is capital and energy intensive, with autoclave and bio-technology competing for lowest overall cost status. The use of surface aerators instead of stirred tank reactors could provide lower costs for bio-oxidation of concentrates. With this in mind, the Delft Inclined Plate reactor was designed with inclined plates above a settler shaped reactor to continuously return slurry from the lowest point in the settler to the surface of the liquid. The multiplate superstructure overcomes the scale-up restriction of the standard circular surface aeration patterns. DIP aerator energy and volume requirements for oxygen transfer from air will be presented in terms of kg O2/kWh and kg O2/m3/h transferred as a function of wt % sand in the slurry and compared to stirred tank performance. Scale up from the 4 m3 pilot unit will be discussed.

Jan 1, 1996

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By A. E. Moss

"IntroductionTHE WORLD-WIDE search for iron ore has been vastly accelerated during the past fifteen years .and Canada is playing a most prominent role in this prospecting boom. During this period, the search for .and development of iron ore deposits in Canada bas proven eminently successful and there is every indication that exploration will continue to be active for many years.This paper has been prepared primarily for the information of those who have bad little or no experience in iron ore exploration. For convenience, it is divided into three parts: ( 1) a brief discussion of the marketing of iron ores, with special reference to Canadian production; (2) a summary of the main features to be considered when prospecting for or evaluating a potential iron ore deposit; and (3) an outline of the methods and procedures used in the search for the direct-shipping iron ores in the Quebec•-Labrador iron ore field.The Iron Ore MarketDue to the tremendous tonnages of high-grade direct-shipping iron ore indicated in the iron ore fields of the Quebec-Labrador and Steep •Rock areas, it might be assumed that there would have been a sharp decline in iron ore prospecting in this country. On the contrary, the development of these two major fields, which must be classed among the world's greatest, has been responsible for much of the current activity. The search for high and medium grade magnetite deposits is being• conducted in many parts of the country and a number of these have reached the development stage. Production is being expanded from the known fields, such as Wabana in Newfoundland and Michipicoten in Ontario."

Jan 1, 1955